NPN SILICON HIGH FREQUENCY TRANSISTOR FEATURES UPA814T OUTLINE DIMENSIONS (Units in mm) * SMALL PACKAGE STYLE: 2 NE688 Die in a 2 mm x 1.25 mm package * LOW NOISE FIGURE: NF = 1.5 dB TYP at 2 GHz * HIGH GAIN BANDWIDTH: fT = 9 GHz * HIGH COLLECTOR CURRENT: 100 mA PACKAGE OUTLINE S06 2.1 0.1 1.25 0.1 0.65 DESCRIPTION 1 6 2 5 3 4 2.0 0.2 NEC's UPA814T is two NPN high frequency silicon epitaxial transistors encapsulated in an ultra small 6 pin SMT package. Each transistor is independently mounted and easily configured for either dual transistor or cascode operation. The high fT, low voltage bias and small size make this device suited for various hand-held wireless applications. ABSOLUTE MAXIMUM RATINGS1 (TA = 25C) SYMBOLS PARAMETERS UNITS RATINGS VCBO Collector to Base Voltage V 9 VCEO Collector to Emitter Voltage V 6 VEBO Emitter to Base Voltage V 2 IC Collector Current mA 100 PT Total Power Dissipation 1 Die 2 Die mW mW 110 200 TJ Junction Temperature C 150 TSTG Storage Temperature C -65 to +150 Note: 1.Operation in excess of any one of these parameters may result in permanent damage. 0.2 (All Leads) 1.3 0.9 0.1 0.7 +0.10 0.15 - 0.05 0 ~ 0.1 PIN OUT 1. Collector Transistor 1 2. Base Transistor 2 3. Collector Transistor 2 4. Emitter Transistor 2 5. Emitter Transistor 1 6. Base Transistor 1 Note: Pin 3 is identified with a circle on the bottom of the package. ELECTRICAL CHARACTERISTICS (TA = 25C) PART NUMBER PACKAGE OUTLINE SYMBOLS PARAMETERS AND CONDITIONS UPA814T S06 UNITS MIN TYP MAX ICBO Collector Cutoff Current at VCB = 5V, IE = 0 A 0.1 IEBO Emitter Cutoff Current at VEB = 1 V, IC = 0 A 0.1 hFE1 Forward Current Gain at VCE = 1 V, IC = 3 mA fT Cre2 |S21E|2 NF hFE1/hFE2 Gain Bandwidth at VCE = 3 V, IC = 20 mA, f = 2 GHz 80 110 GHz 9.0 Feedback Capacitance at VCB = 1 V, IE = 0, f = 1 MHz pF 0.75 Insertion Power Gain at VCE = 3 V, IC =20 mA, f = 2 GHz dB 6.5 Noise Figure at VCE = 3 V, IC = 7 mA, f = 2 GHz dB 1.5 hFE Ratio: hFE1 = Smaller Value of Q1, or Q2 hFE2 = Larger Value of Q1 or Q2 160 0.85 0.85 Notes: 1. Pulsed measurement, pulse width 350 s, duty cycle 2 %. 2. The emitter terminal should be connected to the ground terminal of the 3 terminal capacitance bridge. For Tape and Reel version use part number UPA814T-T1, 3K per reel. California Eastern Laboratories UPA814T TYPICAL PERFORMANCE CURVES (TA = 25C) COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE 2 200 El Pe em rE en ts lem in en To t al t 100 20 10 5 2 1 0.5 0.2 0.1 0.05 0.02 0 50 100 0.01 0 150 0.5 1 Ambient Temperature, TA (C) Base to Emitter Voltage, VBE (V) COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE DC CURRENT GAIN vs. COLLECTOR CURRENT 200 30 VCE = 1 V 200 A 180 A DC Current Gain, hFE Collector Current, IC (mA) VCE = 1 V 50 Free Air Collector Current, IC (mA) Total Power Dissipation, PT (mW) 100 160 A 20 140 A 120 A 100 A 80 A 10 60 A 100 40 A lB = 20 A 0 0 1 2 3 4 5 1 2 5 10 20 50 100 Collector to Emitter Voltage, VCE (V) Collector Current, IC (mA) GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT INSERTION POWER GAIN vs. COLLECTOR CURRENT 10 10 VCE = 1 V f= 2 GHz Insertion Power Gain, IS21eI2 (dB) Gain Bandwidth Product, fT (GHz) 0.5 0.1 0.2 6 5 0 VCE = 1 V f= 2 GHz 5 0 1 2 3 5 Collector Current, IC (mA) 7 10 1 2 3 5 Collector Current, IC (mA) 7 10 UPA814T TYPICAL PERFORMANCE CURVES (TA = 25C) FEEDBACK CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE NOISE FIGURE vs. COLLECTOR CURRENT 3 f = 1 MHz Feddback Capacitance, CRE (pF) VCE = 1 V Noise Figure, NF (dB) f = 2 GHz 2 f = 1 GHz 1 0.5 0.1 0 1 2 3 5 7 10 1 5 10 Collector Current, lC (mA) Collector to Base Voltage, VCB (V) MAXIMUM AVAILABLE GAIN/INSERTION POWER GAIN vs. FREQUENCY NOISE FIGURE vs. FREQUENCY 20 VCE = 1 V lc = 5 mA VCE = 1 V lc = 5 mA 1.5 30 Noise Figure, NF (dB) Maximum Available Power Gain, MAG (dB) Insertion Power Gain, IS21eI2 (dB) 1.0 MAG 20 IS21EI 2 10 0 1 0.5 0.1 0.5 1 5 0.1 Frequency, f (GHz) 0.5 1.0 2 Frequency, f (GHz) ORDERING INFORMATION PART NUMBER UPA814T-T1-A QUANTITY 3000 PACKAGING Tape & Reel Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) * Internet: http://WWW.CEL.COM PRINTED IN USA ON RECYCLED PAPER -1/99 DATA SUBJECT TO CHANGE WITHOUT NOTICE 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.