NCP103 Low Dropout Regulator CMOS 150 mA The NCP103 is 150 mA LDO that provides the engineer with a very stable, accurate voltage with low noise suitable for space constrained, noise sensitive applications. In order to optimize performance for battery operated portable applications, the NCP103 employs the dynamic quiescent current adjustment for very low IQ consumption at no-load. * Operating Input Voltage Range: 1.7 V to 5.5 V * Available in Fixed Voltage Options: 0.9 V to 3.5 V Contact Factory for Other Voltage Options Very Low Quiescent Current of Typ. 50 mA Standby Current Consumption: Typ. 0.1 mA Low Dropout: 75 mV Typical at 150 mA 1% Accuracy at Room Temperature High Power Supply Ripple Rejection: 75 dB at 1 kHz Thermal Shutdown and Current Limit Protections Stable with a 1 mF Ceramic Output Capacitor Available in uDFN 1.0 x 1.0 mm Package These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant Typical Applicaitons * * * * MARKING DIAGRAM 1 UDFN4 MX SUFFIX CASE 517CU Features * * * * * * * * * www.onsemi.com PDAs, Mobile phones, GPS, Smartphones Wireless Handsets, Wireless LAN, Bluetooth(R), Zigbee(R) Portable Medical Equipment Other Battery Powered Applications XX M 1 XX = Specific Device Code M = Date Code PIN CONNECTION EN IN 3 4 2 1 GND OUT (Bottom View) ORDERING INFORMATION See detailed ordering, marking and shipping information on page 14 of this data sheet. VIN VOUT IN CIN EN ON OFF OUT NCP103 GND COUT 1 mF Ceramic Figure 1. Typical Application Schematic (c) Semiconductor Components Industries, LLC, 2016 October, 2019 - Rev. 13 1 Publication Order Number: NCP103/D NCP103 IN ENABLE LOGIC EN THERMAL SHUTDOWN BANDGAP REFERENCE MOSFET DRIVER WITH CURRENT LIMIT OUT AUTO LOW POWER MODE ACTIVE DISCHARGE* EN GND *Active output discharge function is present only in NCP103AMXyyyTCG devices. yyy denotes the particular VOUT option. Figure 2. Simplified Schematic Block Diagram PIN FUNCTION DESCRIPTION Pin No. Pin Name Description 1 OUT Regulated output voltage pin. A small ceramic capacitor with minimum value of 1 mF is needed from this pin to ground to assure stability. 2 GND Power supply ground. 3 EN Driving EN over 0.9 V turns on the regulator. Driving EN below 0.4 V puts the regulator into shutdown mode. 4 IN Input pin. A small capacitor is needed from this pin to ground to assure stability. - EPAD Exposed pad should be connected directly to the GND pin. Soldered to a large ground copper plane allows for effective heat removal. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit VIN -0.3 V to 6 V V Output Voltage VOUT -0.3 V to VIN + 0.3 V or 6 V V Enable Input VEN -0.3 V to VIN + 0.3 V or 6 V V Output Short Circuit Duration tSC s TJ(MAX) 150 C TSTG -55 to 150 C ESD Capability, Human Body Model (Note 2) ESDHBM 2000 V ESD Capability, Machine Model (Note 2) ESDMM 200 V Input Voltage (Note 1) Maximum Junction Temperature Storage Temperature Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per EIA/JESD22-A114, ESD Machine Model tested per EIA/JESD22-A115, Latchup Current Maximum Rating tested per JEDEC standard: JESD78. THERMAL CHARACTERISTICS (Note 3) Rating Thermal Characteristics, uDFN4 1x1 mm Thermal Resistance, Junction-to-Air 3. Single component mounted on 1 oz, FR 4 PCB with 645 mm2 Cu area. www.onsemi.com 2 Symbol Value Unit RqJA 170 C/W NCP103 ELECTRICAL CHARACTERISTICS -40C TJ 85C; VIN = VOUT(NOM) + 1 V for VOUT options greater than 1.5 V. Otherwise VIN = 2.5 V, whichever is greater; IOUT = 1 mA, CIN = COUT = 1 mF, unless otherwise noted. VEN = 0.9 V. Typical values are at TJ = +25C. Min./Max. are for TJ = -40C and TJ = +85C respectively. Parameter Test Conditions Operating Input Voltage Output Voltage Accuracy -40C TJ 85C VOUT 2.0 V Symbol Min VIN VOUT Max Unit 1.7 5.5 V -40 +40 mV +2 % Line Regulation VOUT + 0.5 V VIN 5.5 V (VIN 1.7 V) RegLINE 0.01 0.1 %/V Load Regulation IOUT = 1 mA to 150 mA RegLOAD 10 30 mV IOUT = 1 mA to 150 mA or 150 mA to 1 mA in 1 ms, COUT = 1 mF TranLOAD -30/ +20 Load Transient Dropout Voltage (Note 4) VOUT > 2.0 V Typ 180 235 VOUT = 1.85 V 120 165 75 125 72 120 70 120 65 110 VOUT = 3.0 V VDO VOUT = 3.1 V VOUT = 3.3 V Output Current Limit mV VOUT = 1.5 V VOUT = 2.8 V IOUT = 150 mA -2 VOUT = 90% VOUT(nom) ICL IOUT = 0 mA IQ 50 95 mA Shutdown Current VEN 0.4 V, VIN = 5.5 V IDIS 0.01 1 mA EN Pin Threshold Voltage High Threshold Low Threshold VEN Voltage increasing VEN Voltage decreasing VEN_HI VEN_LO VEN = 5.5 V IEN 0.3 PSRR 75 dB VN 60 mVrms Ground Current EN Pin Input Current 550 mA V 0.9 0.4 1.0 mA Power Supply Rejection Ratio VIN = 3.6 V, VOUT = 3.1 V IOUT = 150 mA Output Noise Voltage VIN = 2.5 V, VOUT = 1.8 V, IOUT = 150 mA f = 10 Hz to 100 kHz Thermal Shutdown Temperature Temperature increasing from TJ = +25C TSD 160 C Temperature falling from TSD TSDH 20 C VEN < 0.4 V, Version A only RDIS 100 W Thermal Shutdown Hysteresis Active Output Discharge Resistance f = 1 kHz 150 mV 4. Characterized when VOUT falls 100 mV below the regulated voltage at VIN = VOUT(NOM) + 1 V. Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 3 NCP103 TYPICAL CHARACTERISTICS 2.815 IOUT = 1 mA 1.204 1.202 1.200 IOUT = 150 mA 1.198 1.196 1.194 VIN = 2.5 V VOUT = 1.2 V CIN = 1 mF COUT = 1 mF 1.192 1.190 1.188 -40 -30 -20 -10 0 10 20 30 40 VOUT, OUTPUT VOLTAGE (V) VOUT, OUTPUT VOLTAGE (V) 1.206 2.810 2.800 2.790 2.785 2.775 2.770 -40 -30 -20 -10 0 50 60 70 80 90 10 20 30 40 50 60 70 80 90 TJ, JUNCTION TEMPERATURE (C) Figure 3. Output Voltage vs. Temperature VOUT = 1.2 V Figure 4. Output Voltage vs. Temperature VOUT = 2.8 V 70 IGND, GROUND CURRENT (mA) -40C 60 50 25C 40 85C 30 20 VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 10 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 600 550 VIN = 3.8 V 500 VOUT = 2.8 V CIN = 1 mF 450 COUT = 1 mF 400 350 300 250 200 150 100 50 0 0.01 0.001 85C 25C -40C 0.1 1 10 100 1000 VIN, INPUT VOLTAGE (V) IOUT, OUTPUT CURRENT (mA) Figure 5. Quiescent Current vs. Input Voltage Figure 6. Ground Current vs. Output Current 0.1 IOUT = 150 mA 540 480 420 360 300 240 180 IOUT = 1 mA 120 60 0 -40 -30 -20 -10 0 VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 10 20 30 40 50 60 70 REGLINE, LINE REGULATION (%/V) IQ, QUIESCENT CURRENT (mA) VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 2.780 TJ, JUNCTION TEMPERATURE (C) 600 IGND, GROUND CURRENT (mA) IOUT = 150 mA 2.795 80 0 0.0 IOUT = 1 mA 2.805 80 90 0.08 0.06 0.04 0.02 0 -0.02 -0.04 -0.06 -0.08 -1 -40 -30 -20 -10 0 VIN = 1.7 V to 5.5 V VOUT = 1.2 V IOUT = 1 mA CIN = 1 mF COUT = 1 mF 10 20 30 40 50 60 70 80 90 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 7. Ground Current vs. Temperature Figure 8. Line Regulation vs. Output Current VOUT = 1.2 V www.onsemi.com 4 NCP103 TYPICAL CHARACTERISTICS 0.06 0.04 0.02 0 -0.02 VIN = 3.8 V to 5.5 V VOUT = 2.8 V IOUT = 1 mA CIN = 1 mF COUT = 1 mF -0.04 -0.06 -0.08 -0.1 -40 -30 -20 -10 0 REGLOAD, LOAD REGULATION (mV) REGLOAD, LOAD REGULATION (mV) 10 10 20 30 40 50 60 70 80 90 8 7 6 5 4 VIN = 2.5 V VOUT = 1.2 V IOUT = 1 mA to 150 mA CIN = 1 mF COUT = 1 mF 3 2 1 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 TJ, JUNCTION TEMPERATURE (C) Figure 9. Line Regulation vs. Temperature VOUT = 2.8 V Figure 10. Load Regulation vs. Temperature VOUT = 1.2 V 10 100 9 90 8 7 6 5 4 VIN = 3.8 V VOUT = 2.8 V IOUT = 1 mA to 150 mA CIN = 1 mF COUT = 1 mF 3 2 1 0 -40 -30 -20 -10 0 10 20 30 40 80 70 60 TJ = 85C 50 TJ = -40C 40 30 VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 20 TJ = 25C 10 0 50 60 70 80 90 0 15 30 45 60 75 90 105 120 135 150 TJ, JUNCTION TEMPERATURE (C) IOUT, OUTPUT CURRENT (mA) Figure 11. Load Regulation vs. Temperature VOUT = 2.8 V Figure 12. Dropout Voltage vs. Output Current VOUT = 2.8 V 100 800 750 90 IOUT = 150 mA 80 70 60 IOUT = 100 mA 50 40 IOUT = 0 mA 30 20 10 0 -40 -30 -20 -10 0 VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 10 20 30 40 50 60 70 ICL, CURRENT LIMIT (mA) VDROP, DROPOUT VOLTAGE (mV) 9 TJ, JUNCTION TEMPERATURE (C) VDROP, DROPOUT VOLTAGE (mV) REGLINE, LINE REGULATION (%/V) 0.1 0.08 700 650 VOUT = 2.8 V 600 VOUT = 1.2 V 550 500 450 400 350 80 90 300 -40 -30 -20 -10 0 VIN = VOUT(nom) + 1 V or 2.5 V VOUT = 90% VOUT(nom) CIN = 1 mF COUT = 1 mF 10 20 30 40 50 60 70 80 90 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 13. Dropout Voltage vs. Temperature Figure 14. Current Limit vs. Temperature www.onsemi.com 5 NCP103 ISC, SHORT-CIRCUIT CURRENT (mA) 800 750 700 VOUT = 2.8 V 650 VOUT = 1.2 V 600 550 500 450 VIN = VOUT(nom) + 1 V or 2.5 V VOUT = 0 V CIN = 1 mF COUT = 1 mF 400 350 300 -40 -30 -20 -10 0 10 20 30 40 800 750 700 650 600 550 500 450 400 VOUT = 0 V CIN = 1 mF COUT = 1 mF 350 300 50 60 70 80 90 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4 5.6 TJ, JUNCTION TEMPERATURE (C) VIN, INPUT VOLTAGE (V) Figure 15. Short-Circuit Current vs. Temperature Figure 16. Short-Circuit Current vs. Input Voltage 350 0.9 315 0.8 IEN, ENABLE CURRENT (nA) 1 OFF -> ON 0.7 0.6 ON -> OFF 0.5 0.4 0.3 VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 0.2 0.1 0 -40 -30 -20 -10 0 10 20 30 40 VEN = 5.5 V 280 245 210 VEN = 0.4 V 175 140 105 35 0 -40 -30 -20 -10 0 50 60 70 80 90 VIN = 5.5 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 70 10 20 30 40 50 60 70 80 90 TJ, JUNCTION TEMPERATURE (C) TJ, JUNCTION TEMPERATURE (C) Figure 17. Enable Voltage Threshold vs. Temperature Figure 18. Current to Enable Pin vs. Temperature 100 IDIS, DISABLE CURRENT (nA) VEN, VOLTAGE ON ENABLE PIN (V) ISC, SHORT-CIRCUIT CURRENT (mA) TYPICAL CHARACTERISTICS 80 60 40 20 0 -20 -40 VIN = 5.5 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF -60 -80 -100 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 TJ, JUNCTION TEMPERATURE (C) Figure 19. Disable Current vs. Temperature www.onsemi.com 6 NCP103 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE NOISE (mV/rtHz) 10000 IOUT = 150 mA 1000 IOUT 100 10 VIN = 2.5 V VOUT = 1.2 V CIN = 1 mF COUT = 1 mF 1 0.01 0.1 IOUT = 10 mA RMS Output Noise (mV) 10 Hz - 100 kHz 100 Hz - 100 kHz 1 mA 60.93 59.11 10 mA 52.73 50.63 150 mA 51.20 48.96 IOUT = 1 mA 1 100 10 1000 FREQUENCY (kHz) Figure 20. Output Voltage Noise Spectral Density for VOUT = 1.2 V, COUT = 1 mF OUTPUT VOLTAGE NOISE (mV/rtHz) 10000 IOUT = 150 mA 1000 IOUT 100 10 IOUT = 10 mA VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 1 mF 1 0.01 0.1 RMS Output Noise (mV) 10 Hz - 100 kHz 100 Hz - 100 kHz 74.66 1 mA 79.23 10 mA 75.03 70.37 150 mA 77.28 72.66 IOUT = 1 mA 1 10 100 1000 FREQUENCY (kHz) Figure 21. Output Voltage Noise Spectral Density for VOUT = 2.8 V, COUT = 1 mF OUTPUT VOLTAGE NOISE (mV/rtHz) 10000 IOUT = 150 mA 1000 IOUT 100 10 1 mA VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF COUT = 4.7 mF 1 0.01 0.1 IOUT = 10 mA RMS Output Noise (mV) 10 Hz - 100 kHz 100 Hz - 100 kHz 80.17 75.29 10 mA 81.28 76.46 150 mA 81.31 76.77 IOUT = 1 mA 1 10 100 1000 FREQUENCY (kHz) Figure 22. Output Voltage Noise Spectral Density for VOUT = 2.8 V, COUT = 4.7 mF www.onsemi.com 7 NCP103 TYPICAL CHARACTERISTICS 100 RR, RIPPLE REJECTION (dB) 80 70 60 50 40 30 20 10 0 0.1 VIN = 3.8 V VOUT = 2.8 V CIN = none MLCC, X7R, 1206 size 1 10 100 1000 10000 IOUT = 1 mA IOUT = 10 mA IOUT = 150 mA 90 80 70 60 50 40 30 20 10 0 0.1 VIN = 3.8 V VOUT = 2.8 V CIN = none MLCC, X7R, 1206 size 1 10 100 1000 10000 FREQUENCY (kHz) FREQUENCY (kHz) Figure 23. Power Supply Rejection Ratio, VOUT = 1.2 V, COUT = 1 mF Figure 24. Power Supply Rejection Ratio, VOUT = 2.8 V, COUT = 4.7 mF 100 10 ESR (W) RR, RIPPLE REJECTION (dB) 100 IOUT = 1 mA IOUT = 10 mA IOUT = 150 mA 90 UNSTABLE OPERATION 1 STABLE OPERATION VIN = 5.5 V CIN = 1 mF COUT = 1 mF MLCC, X7R, 1206 size 0.1 0.01 0 15 30 45 60 75 90 105 120 135 IOUT, OUTPUT CURRENT (mA) Figure 25. Output Capacitor ESR vs. Output Current www.onsemi.com 8 150 NCP103 VOUT IINRUSH VOUT 40 ms/div 40 ms/div IINRUSH 1 V/div VOUT VIN = 3.8 V VOUT = 2.8 V VEN = 1 V COUT = 1 mF CIN = 1 mF IOUT = 150 mA VEN VOUT 40 ms/div 40 ms/div Figure 28. Enable Turn-on Response, COUT = 4.7 mF, IOUT = 1 mA Figure 29. Enable Turn-on Response, COUT = 4.7 mF, IOUT = 150 mA VIN VIN = 3.8 V to 4.8 V VOUT = 2.8 V COUT = 1 mF CIN = 1 mF tRISE = 1 ms IOUT = 1 mA 500 mV/div 1 V/div 500 mV/div VIN = 3.8 V VOUT = 2.8 V VEN = 1 V COUT = 1 mF CIN = 1 mF IOUT = 1 mA IINRUSH 500 mV/div Figure 27. Enable Turn-on Response, COUT = 1 mF, IOUT = 150 mA 200 mA/div 500 mV/div Figure 26. Enable Turn-on Response, COUT = 1 mF, IOUT = 1 mA VEN VIN = 4.8 V to 3.8 V VOUT = 2.8 V COUT = 1 mF CIN = 1 mF IOUT = 1 mA VIN tFALL = 1 ms VOUT 10 mV/div 10 mV/div 200 mA/div VEN 1 V/div 1 V/div IINRUSH VIN = 3.8 V VOUT = 2.8 V VEN = 1 V COUT = 1 mF CIN = 1 mF IOUT = 150 mA VOUT 20 ms/div 10 ms/div Figure 30. Line Transient Response - Rising Edge, VOUT = 2.8 V, IOUT = 1 mA Figure 31. Line Transient Response - Falling Edge, VOUT = 2.8 V, IOUT = 1 mA www.onsemi.com 9 200 mA/div VEN 500 mV/div VIN = 3.8 V VOUT = 2.8 V VEN = 1 V COUT = 1 mF CIN = 1 mF IOUT = 1 mA 200 mA/div 500 mV/div TYPICAL CHARACTERISTICS NCP103 VOUT 500 mV/div tRISE = 1 ms VIN = 3.8 V to 4.8 V VOUT = 2.8 V COUT = 10 mF CIN = 1 mF IOUT = 150 mA VIN 20 mV/div VIN VOUT tFALL = 1 ms 4 ms/div 4 ms/div Figure 33. Line Transient Response - Falling Edge, VOUT = 2.8 V, IOUT = 150 mA IOUT 50 mA/div VIN = 2.5 V VOUT = 1.2 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) IOUT tFALL = 1 ms COUT = 1 mF 20 mV/div 20 mV/div COUT = 4.7 mF COUT = 1 mF VOUT COUT = 1 mF 4 ms/div 20 ms/div Figure 34. Load Transient Response - Rising Edge, VOUT = 1.2 V, IOUT = 1 mA to 150 mA, COUT = 1 mF, 4.7 mF Figure 35. Load Transient Response - Falling Edge, VOUT = 1.2 V, IOUT = 1 mA to 150 mA, COUT = 1 mF, 4.7 mF VOUT tRISE = 1 ms 50 mA/div IOUT IOUT VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) tFALL = 1 ms COUT = 1 mF COUT = 4.7 mF 20 mV/div 50 mA/div VIN = 2.5 V VOUT = 1.2 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) tRISE = 1 ms VOUT 20 mV/div VIN = 4.8 V to 3.8 V VOUT = 2.8 V COUT = 1 mF CIN = 1 mF IOUT = 150 mA Figure 32. Line Transient Response - Rising Edge, VOUT = 2.8 V, IOUT = 150 mA 50 mA/div 20 mV/div 500 mV/div TYPICAL CHARACTERISTICS COUT = 1 mF VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) COUT = 4.7 mF VOUT 4 ms/div 10 ms/div Figure 36. Load Transient Response - Rising Edge, VOUT = 2.8 V, IOUT = 1 mA to 150 mA, COUT = 1 mF, 4.7 mF Figure 37. Load Transient Response - Falling Edge, VOUT = 2.8 V, IOUT = 1 mA to 150 mA, COUT = 1 mF, 4.7 mF www.onsemi.com 10 NCP103 VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) IOUT IOUT 500 mA/div 500 mA/div TYPICAL CHARACTERISTICS tRISE = 1 ms tFALL = 1 ms 20 mV/div VIN = 3.8 V VIN = 5.5 V VIN = 3.8 V VOUT VIN = 5.5 V 2 ms/div 10 ms/div Figure 38. Load Transient Response - Rising Edge, VOUT = 2.8 V, IOUT = 1 mA to 150 mA, VIN = 3.8 V, 5.5 V Figure 39. Load Transient Response - Falling Edge, VOUT = 2.8 V, IOUT = 1 mA to 150 mA, VIN = 3.8 V, 5.5 V VIN = 5.5 V VOUT = 2.8 V IOUT = 10 mA CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) VIN Full Load 100 mA/div 20 mV/div VOUT VIN = 3.8 V VOUT = 2.8 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) VOUT Overheating VIN = 5.5 V VOUT = 1.2 V CIN = 1 mF (MLCC) COUT = 1 mF (MLCC) IOUT Thermal Shutdown 1 V/div 50 mV/div VOUT TSD Cycling 4 ms/div 10 ms/div Figure 40. Turn-on/off - Slow Rising VIN Figure 41. Short-Circuit and Thermal Shutdown www.onsemi.com 11 NCP103 APPLICATIONS INFORMATION General The NCP103 is a high performance 150 mA Low Dropout Linear Regulator. This device delivers very high PSRR (over 75 dB at 1 kHz) and excellent dynamic performance as load/line transients. In connection with very low quiescent current this device is very suitable for various battery powered applications such as tablets, cellular phones, wireless and many others. The device is fully protected in case of output overload, output short circuit condition and overheating, assuring a very robust design. disable state the device consumes as low as typ. 10 nA from the VIN. If the EN pin voltage >0.9 V the device is guaranteed to be enabled. The NCP103 regulates the output voltage and the active discharge transistor is turned-off. The EN pin has internal pull-down current source with typ. value of 300 nA which assures that the device is turned-off when the EN pin is not connected. In the case where the EN function isn't required the EN should be tied directly to IN. Input Capacitor Selection (CIN) Output Current Limit It is recommended to connect at least a 1mF Ceramic X5R or X7R capacitor as close as possible to the IN pin of the device. This capacitor will provide a low impedance path for unwanted AC signals or noise modulated onto constant input voltage. There is no requirement for the min. /max. ESR of the input capacitor but it is recommended to use ceramic capacitors for their low ESR and ESL. A good input capacitor will limit the influence of input trace inductance and source resistance during sudden load current changes. Larger input capacitor may be necessary if fast and large load transients are encountered in the application. Output Current is internally limited within the IC to a typical 550 mA. The NCP103 will source this amount of current measured with a voltage drops on the 90% of the nominal VOUT. If the Output Voltage is directly shorted to ground (VOUT = 0 V), the short circuit protection will limit the output current to 580 mA (typ). The current limit and short circuit protection will work properly over whole temperature range and also input voltage range. There is no limitation for the short circuit duration. Thermal Shutdown When the die temperature exceeds the Thermal Shutdown threshold (TSD - 160C typical), Thermal Shutdown event is detected and the device is disabled. The IC will remain in this state until the die temperature decreases below the Thermal Shutdown Reset threshold (TSDU * 140C typical). Once the IC temperature falls below the 140C the LDO is enabled again. The thermal shutdown feature provides the protection from a catastrophic device failure due to accidental overheating. This protection is not intended to be used as a substitute for proper heat sinking. Output Decoupling (COUT) The NCP103 requires an output capacitor connected as close as possible to the output pin of the regulator. The recommended capacitor value is 1 mF and X7R or X5R dielectric due to its low capacitance variations over the specified temperature range. The NCP103 is designed to remain stable with minimum effective capacitance of 0.22 mF to account for changes with temperature, DC bias and package size. Especially for small package size capacitors such as 0402 the effective capacitance drops rapidly with the applied DC bias. There is no requirement for the minimum value of Equivalent Series Resistance (ESR) for the COUT but the maximum value of ESR should be less than 3 W. Larger output capacitors and lower ESR could improve the load transient response or high frequency PSRR. It is not recommended to use tantalum capacitors on the output due to their large ESR. The equivalent series resistance of tantalum capacitors is also strongly dependent on the temperature, increasing at low temperature. Power Dissipation As power dissipated in the NCP103 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. The maximum power dissipation the NCP103 can handle is given by: Enable Operation P D(MAX) + The NCP103 uses the EN pin to enable/disable its device and to deactivate/activate the active discharge function. If the EN pin voltage is <0.4 V the device is guaranteed to be disabled. The pass transistor is turned-off so that there is virtually no current flow between the IN and OUT. The active discharge transistor is active so that the output voltage VOUT is pulled to GND through a 100 W resistor. In the 125 C * T A q JA (eq. 1) The power dissipated by the NCP103 for given application conditions can be calculated from the following equations: P D [ V INI GND@I OUT ) I OUTV IN * V OUT www.onsemi.com 12 (eq. 2) NCP103 qJA, JUNCTION-TO-AMBIENT THERMAL RESISTANCE (C/W) 240 PD(MAX), TA = 25C, 2 oz Cu 0.9 220 PD(MAX), TA = 25C, 1 oz Cu 200 180 qJA, 1 oz Cu 160 0.7 0.6 140 qJA, 2 oz Cu 0.5 120 100 0 0.8 100 200 300 400 500 600 PD(MAX), MAXIMUM POWER DISSIPATION (W) 1 260 0.4 700 COPPER HEAT SPREADER AREA (mm2) Figure 42. qJA vs. Copper Area (uDFN4) Reverse Current nominal value. This time is dependent on various application conditions such as VOUT(NOM), COUT and TA. For example typical value for VOUT = 1.2 V, COUT = 1 mF, IOUT = 1 mA and TA = 25C is 90 ms. The PMOS pass transistor has an inherent body diode which will be forward biased in the case that VOUT > VIN. Due to this fact in cases, where the extended reverse current condition can be anticipated the device may require additional external protection. PCB Layout Recommendations To obtain good transient performance and good regulation characteristics place CIN and COUT capacitors close to the device pins and make the PCB traces wide. In order to minimize the solution size, use 0402 capacitors. Larger copper area connected to the pins will also improve the device thermal resistance. The actual power dissipation can be calculated from the equation above (Equation 2). Expose pad should be tied the shortest path to the GND pin. Power Supply Rejection Ratio The NCP103 features very good Power Supply Rejection ratio. If desired the PSRR at higher frequencies in the range 100 kHz - 10 MHz can be tuned by the selection of COUT capacitor and proper PCB layout. Turn-On Time The turn-on time is defined as the time period from EN assertion to the point in which VOUT will reach 98% of its www.onsemi.com 13 NCP103 ORDERING INFORMATION Voltage Option Marking NCP103AMX090TCG 0.9 V AQ 0 NCP103AMX100TCG 1.0 V 5 180 NCP103AMX105TCG 1.05 V A 0 NCP103AMX110TCG 1.1 V E 180 NCP103AMX120TCG 1.2 V D 0 NCP103AMX125TCG 1.25 V D 180 NCP103AMX130TCG 1.3 V AD 0 NCP103AMX150TCG 1.5 V E 0 NCP103AMX160TCG 1.6 V Y 180 NCP103AMX180TCG 1.8 V K 180 NCP103AMX185TCG 1.85 V F 0 NCP103AMX210TCG 2.1 V P 180 NCP103AMX220TCG 2.2 V R 180 NCP103AMX240TCG 2.4 V AL 0 NCP103AMX250TCG 2.5 V AX 0 NCP103AMX260TCG 2.6 V V 180 NCP103AMX270TCG 2.7 V AK 0 NCP103AMX280TCG 2.8 V J 0 NCP103AMX285TCG 2.85 V K 0 NCP103AMX300TCG 3.0 V L 0 NCP103AMX310TCG 3.1 V P 0 NCP103AMX320TCG 3.2 V AY 0 NCP103AMX330TCG 3.3 V Q 0 NCP103AMX345TCG 3.45 V AE 0 NCP103AMX350TCG 3.5 V 3 180 NCP103AMX360TCG 3.6 V AV 0 NCP103BMX100TCG 1.0 V 5 270 NCP103BMX105TCG 1.05 V A 90 NCP103BMX110TCG 1.1 V E 270 NCP103BMX120TCG 1.2 V D 90 NCP103BMX125TCG 1.25 V D 270 NCP103BMX130TCG 1.3 V CD 0 NCP103BMX150TCG 1.5 V E 90 NCP103BMX160TCG 1.6 V Y 270 NCP103BMX180TCG 1.8 V K 270 NCP103BMX185TBG 1.85 V CJ 0 NCP103BMX185TCG 1.85 V CJ 0 NCP103BMX210TCG 2.1 V P 270 NCP103BMX220TCG 2.2 V R 270 NCP103BMX250TCG 2.5 V CH 0 NCP103BMX260TCG 2.6 V V 270 Device Marking Rotation NCP103BMX280TCG 2.8 V J 90 NCP103BMX285TCG 2.85 V K 90 NCP103BMX300TCG 3.0 V L 90 NCP103BMX310TCG 3.1 V P 90 NCP103BMX330TCG 3.3 V Q 90 NCP103BMX345TCG 3.45 V CE 0 NCP103BMX350TCG 3.5 V 3 270 Option Package Shipping With active output discharge function uDFN4 (Pb-Free) 3000 / Tape & Reel Without active output discharge function uDFN4 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Bluetooth is a registered trademark of Bluetooth SIG. ZigBee is a registered trademark of ZigBee Alliance. www.onsemi.com 14 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS UDFN4 1.0x1.0, 0.65P CASE 517CU ISSUE A 1 SCALE 4:1 A B D PIN ONE REFERENCE 2X 0.05 C 0.05 C 2X EE EE 3X C0.18 X 45 5 C0.27 x 0.25 E L2 A 0.10 C DIM A A1 A3 b D D2 E e L L2 (A3) A1 0.05 C C SIDE VIEW e DETAIL A 3X 2 SEATING PLANE MILLIMETERS MIN MAX --- 0.60 0.00 0.05 0.15 REF 0.20 0.30 1.00 BSC 0.38 0.58 1.00 BSC 0.65 BSC 0.20 0.30 0.27 0.37 GENERIC MARKING DIAGRAM* e/2 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.03 AND 0.07 FROM THE TERMINAL TIPS. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. DETAIL A TOP VIEW NOTE 4 DATE 18 DEC 2014 L XX M 1 D2 D2 45 5 4 XX = Specific Device Code M = Date Code 3 4X BOTTOM VIEW b 0.10 M C A B 0.05 M C *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G" or microdot " G", may or may not be present. NOTE 3 RECOMMENDED MOUNTING FOOTPRINT* 2X 0.65 PITCH 0.58 DETAIL B 3X 0.43 PACKAGE OUTLINE 4X 0.23 1.30 0.53 1 4X 0.30 3X 0.10 DETAIL B DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: 98AON76666F UDFN4, 1.0X1.0, 0.65P Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2019 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative