D−8 DGN−8 D−16
1
FEATURES
TPS2065-1
DGNPACKAGE
(TOPVIEW)
TPS2062-1/TPS2066-1
DANDDGNPACKAGE
(TOPVIEW)
DESCRIPTION
APPLICATIONS
TPS201xA
TPS202x
TPS203x
33 mΩ, single 0.2 A − 2 A
0.2 A − 2 A
0.2 A − 2 A
TPS2014
TPS2015
TPS2041B
TPS2051B
TPS2045
TPS2055
TPS2061
TPS2065
80 mΩ, single 600 mA
1 A
500 mA
500 mA
250 mA
250 mA
1 A
1 A
GENERAL SWITCH CATALOG
TPS2042B
TPS2052B
TPS2046
TPS2056
TPS2062
TPS2066
TPS2060
TPS2064
80 mΩ, dual 500 mA
500 mA
250 mA
250 mA
1 A
1 A
1.5 A
1.5 A
TPS2100/1
260 mΩIN1 500 mA
IN2 10 mA
OUT
IN1
IN2 TPS2102/3/4/5
IN1 500 mA
IN2 100 mA
1.3 Ω
TPS2043B
TPS2053B
TPS2047
TPS2057
80 mΩ, triple
500 mA
500 mA
250 mA
250 mA
TPS2044B
TPS2054B
TPS2048
TPS2058
80 mΩ, quad
500 mA
500 mA
250 mA
250 mA
80 mΩ, dual
TPS2080
TPS2081
TPS2082
TPS2090
500 mA
500 mA
500 mA
250 mA
TPS2091
TPS2092 250 mA
250 mA
80 mΩ, quad
TPS2085
TPS2086
TPS2087
TPS2095
500 mA
500 mA
500 mA
250 mA
TPS2096
TPS2097 250 mA
250 mA
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
CURRENT-LIMITED, POWER-DISTRIBUTION SWITCHES
•Output Discharge Function•70-m ΩHigh-Side MOSFET•1-A Continuous Current•Thermal and Short-Circuit Protection•Accurate Current Limit(1.1 A min, 1.9 A max)•Operating Range: 2.7 V to 5.5 V
The TPS206x-1 power-distribution switches are•0.6-ms Typical Rise Time
intended for applications where heavy capacitive•Undervoltage Lockout
loads and short-circuits are likely to be encountered.This device incorporates 70-m ΩN-channel MOSFET•Deglitched Fault Report ( OC)
power switches for power-distribution systems that•No OC Glitch During Power Up
require multiple power switches in a single package.•1-A Maximum Standby Supply Current
Each switch is controlled by a logic enable input.•Ambient Temperature Range: -40 ° C to 85 ° C
Gate drive is provided by an internal charge pumpdesigned to control the power-switch rise times and•ESD Protection
fall times to minimize current surges during switching.The charge pump requires no external componentsand allows operation from supplies as low as 2.7 V.•Heavy Capacitive Loads
These switches provide a discharge function that•Short-Circuit Protections
provides a controlled discharge of the output voltagestored on the output capacitor.
When the output load exceeds the current-limit threshold or a short is present, the device limits the output currentto a safe level by switching into a constant-current mode, pulling the overcurrent ( OCx) logic output low. Whencontinuous heavy overloads and short-circuits increase the power dissipation in the switch, causing the junctiontemperature to rise, a thermal protection circuit shuts off the switch to prevent damage. Recovery from a thermalshutdown is automatic once the device has cooled sufficiently. Internal circuitry ensures that the switch remainsoff until valid input voltage is present. This power-distribution switch is designed to set current limit at 1.5 Atypically.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
Copyright © 2007 – 2009, Texas Instruments IncorporatedPRODUCTION DATA information current as of publication date.Products conform to specifications per the terms of TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
ABSOLUTE MAXIMUM RATINGS
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foamduring storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE OPTION AND ORDERING INFORMATION
(1)
RECOMMENDED TYPICAL PACKAGEDMAXIMUM SHORT-CIRCUIT NUMBER OF DEVICES
(2)T
A
ENABLE
CONTINUOUS CURRENT LIMIT SWITCHES
MSOP (DGN) SOIC(D)LOAD CURRENT AT 25 ° C
Active high Single TPS2065DGN-1– 40 ° C to 85 ° C Active low 1 A 1.5 A TPS2062D-1DualActive high TPS2066DGN-1
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TIwebsite at www.ti.com .(2) The package is available taped and reeled. Add an R suffix to device types (e.g., TPS2062-1DR).
over operating free-air temperature range unless otherwise noted
(1)
UNIT
Input voltage range, V
I(IN)
(2)
– 0.3 V to 6 VOutput voltage range, V
O(OUT)
(2)
, V
O(OUTx)
-0.3 V to 6 VInput voltage range, V
I( EN)
, V
I(EN)
, V
I( ENx)
, V
I(ENx)
– 0.3 V to 6 VVoltage range, V
I( OC)
, V
I( OCx)
– 0.3 V to 6 VContinuous output current, I
O(OUT)
, I
O(OUTx)
Internally limitedContinuous total power dissipation See Dissipation Rating TableOperating virtual junction temperature range, T
J
-40 ° C to 125 ° CStorage temperature range, T
stg
– 65 ° C to 150 ° CHuman body model MIL-STD-883C 2 kVElectrostatic discharge (ESD) protection
Charge device model (CDM) 500 V
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under recommended operatingconditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2) All voltages are with respect to GND.
2Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
DISSIPATING RATING TABLE
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
T
A
≤25 ° C DERATING FACTOR T
A
= 70 ° C T
A
= 85 ° CPACKAGE
POWER RATING ABOVE T
A
= 25 ° C POWER RATING POWER RATING
D-8 585.82 mW 5.8582 mW/ ° C 322.20 mW 234.32 mWDGN-8 1712.3 mW 17.123 mW/ ° C 941.78 mW 684.33 mW
MIN MAX UNIT
Input voltage, V
I(IN)
2.7 5.5 VInput voltage, V
I( EN)
, V
I(EN)
, V
I( ENx)
, V
I(ENx)
0 5.5 VContinuous output current, I
O(OUT)
, I
O(OUTx)
0 1 ASteady state current through discharge. Device disabled, measured through output pin(s) 8 mAOperating virtual junction temperature, T
J
-40 125 ° C
over recommended operating junction temperature range, V
I(IN)
= 5.5 V, I
O
= 1 A, V
I(/ENx)
= 0 V, or V
I(ENx)
= 5.5 V (unlessotherwise noted)
PARAMETER TEST CONDITIONS
(1)
MIN TYP MAX UNIT
POWER SWITCH
Static drain-source on-state resistance,
V
I(IN)
= 5 V or 3.3 V, I
O
= 1 A, – 40 ° C ≤T
J
≤125 ° C 70 135 m Ω5-V operation and 3.3-V operationr
DS(on)
Static drain-source on-state resistance,
V
I(IN)
= 2.7 V, I
O
= 1 A, -40 ° C ≤T
J
≤125 ° C 75 150 m Ω2.7-V operation
(2)
V
I(IN)
= 5.5 V 0.6 1.5t
r
(2)
Rise time, output
V
I(IN)
= 2.7 V 0.4 1C
L
= 1 µF, R
L
= 5 Ω, T
J
= 25 ° C msV
I(IN)
= 5.5 V 0.05 0.5t
f
(2)
Fall time, output
V
I(IN)
= 2.7 V 0.05 0.5
ENABLE INPUT EN OR EN
V
IH
High-level input voltage 2.7 V ≤V
I(IN)
≤5.5 V 2
VV
IL
Low-level input voltage 2.7 V ≤V
I(IN)
≤5.5 V 0.8
I
I
Input current V
I( ENx)
= 0 V or 5.5 V, V
I(ENx)
= 0 V or 5.5 V -0.5 0.5 µA
t
on
(3)
Turnon time C
L
= 100 µF, R
L
= 5 Ω3
mst
off
(3)
Turnoff time C
L
= 100 µF, R
L
= 5 Ω10
CURRENT LIMIT
T
J
= 25 ° C 1.1 1.5 1.9V
I(IN)
= 5 V, OUT connected to GND,I
OS
Short-circuit output current Adevice enabled into short-circuit
-40 ° C ≤T
J
≤125 ° C 1.1 1.5 2.1
I
OC_TRIP
(3)
Overcurrent trip threshold V
I(IN)
= 5 V, current ramp ( ≤100 A/s) on OUT 2.4 3 A
SUPPLY CURRENT (TPS2065-1)
T
J
= 25 ° C 0.5 1No load on OUT, V
I( ENx)
= 5.5 V,Supply current, low-level output µAor V
I(ENx)
= 0 V
-40 ° C ≤T
J
≤125 ° C 0.5 10
T
J
= 25 ° C 43 60No load on OUT, V
I( ENx)
= 0 V,Supply current, high-level output µAor V
I(ENx)
= 5.5 V
-40 ° C ≤T
J
≤125 ° C 43 70
Reverse leakage current V
I(OUTx)
= 5.5 V, IN = ground
(3)
T
J
= 25 ° C 0 µA
SUPPLY CURRENT (TPS2062-1, TPS2066-1)
T
J
= 25 ° C 0.5 1No load on OUT, V
I( ENx)
= 5.5 V,Supply current, low-level output µAor V
I(ENx)
= 0 V
-40 ° C ≤T
J
≤125 ° C 0.5 20
T
J
= 25 ° C 50 70No load on OUT, V
I( ENx)
= 0 V,Supply current, high-level output µAor V
I(ENx)
= 5.5 V
-40 ° C ≤T
J
≤125 ° C 50 90
Reverse leakage current V
I(OUTx)
= 5.5 V, IN = ground
(3)
T
J
= 25 ° C 0.2 µA
(1) Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into accountseparately.
(2) Not tested in production, specified by design.(3) Not tested in production, specified by design.
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
DEVICE INFORMATION
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)over recommended operating junction temperature range, V
I(IN)
= 5.5 V, I
O
= 1 A, V
I(/ENx)
= 0 V, or V
I(ENx)
= 5.5 V (unlessotherwise noted)
PARAMETER TEST CONDITIONS
(1)
MIN TYP MAX UNIT
UNDERVOLTAGE LOCKOUT
Low-level input voltage, IN 2 2.5 V
Hysteresis, IN T
J
= 25 ° C 75 mV
OVERCURRENT OC1 and OC2
Output low voltage, V
OL(OCx)
I
O( OCx)
= 5 mA 0.4 V
Off-state current
(4)
V
O( OCx)
= 5 V or 3.3 V 1 µA
OC deglitch
(4)
OCx assertion or deassertion 4 8 15 ms
Discharge resistance V
CC
= 5 V, disabled, I
O
= 1 mA 100 Ω
THERMAL SHUTDOWN
(5)
Thermal shutdown threshold
(4)
135 ° C
Recovery from thermal shutdown
(4)
125 ° C
Hysteresis
(4)
10 ° C
(4) Not tested in production, specified by design.(5) The thermal shutdown only reacts under overcurrent conditions.
Pin Functions
PIN
I/O DESCRIPTIONNAME TPS2065-1 TPS2062-1 TPS2066-1
EN 4 – – I Enable input, logic high turns on power switchEN1 – 3 – I Enable input, logic low turns on channel 1EN2 – 4 – I Enable input, logic high turns on channel 2EN1 – – 3 I Enable input, logic high turns on channel 1EN2 – – 4 I Enable input, logic high turns on channel 2GND 1 1 1 Ground connectionIN 2, 3 2 2 I Input voltage; connect a 0.1 µF or greater ceramic capacitor from IN to GNDas close to the IC as possibleOC 5 – – O Active-low open-drain output, asserted during over-currentOC1 – 8 8 O Active-low open-drain output, asserted during over-current for channel 1OC2 5 5 O Active-low open-drain output, asserted during over-current for channel 2OUT 6, 7, 8 – – O Power-switch outputOUT1 – 7 7 O Power-switch output for channel 1OUT2 – 6 6 O Power-switch output for channel 2
4Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
OUT
OC
IN
EN
GND
Current
Limit
Driver
UVLO
Charge
Pump
CS
Thermal
Sense
Deglitch
Note A:Currentsense
(SeeNote A)
EN Discharge
Control
Thermal
Sense
Driver Current
Limit
Charge
Pump
UVLO
CS
Driver Current
Limit
CS
Thermal
Sense
Charge
Pump
GND
EN1
IN
EN2
OC1
OUT1
OUT2
OC2
Deglitch
Deglitch
(SeeNote A)
(SeeNote A)
(SeeNoteB)
(SeeNoteB)
Note A:Currentsense
NoteB: Activelow( )forTPS2062. Activehigh( )forTPS2066ENx ENx
EN Discharge
Control
EN Discharge
Control
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
FUNCTIONAL BLOCK DIAGRAM (TPS2065-1)
FUNCTIONAL BLOCK DIAGRAM (TPS2062-1 and TPS2066-1)
FUNCTIONAL BLOCK DIAGRAM (TPS2062-1 and TPS2066-1)
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
PARAMETER MEASUREMENT INFORMATION
RLCL
OUT
trtf
90% 90%
10%
10%
50% 50%
90%
10%
VO(OUT)
VI(EN)
VO(OUT)
VOLTAGE WAVEFORMS
TEST CIRCUIT
ton toff
50% 50%
90%
10%
VI(EN)
VO(OUT)
ton toff
VI(EN)
5 V/div
VO(OUT)
2 V/div
RL = 5 W,
CL = 1 mF
TA = 255C
t − Time − 500 ms/div
VI(EN)
5 V/div
VO(OUT)
2 V/div
RL = 5 W,
CL = 1 mF
TA = 255C
t − Time − 500 ms/div
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
Figure 1. Test Circuit and Voltage Waveforms
Figure 2. Turnon Delay and Rise Time With 1- µ F Load Figure 3. Turnoff Delay and Fall Time With 1- µ F Load
6Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
VI(EN)
5 V/div
VO(OUT)
2 V/div
RL = 5 W,
CL = 100 mF
TA = 255C
t − Time − 500 ms/div
VI(EN)
5 V/div
IO(OUT)
500 mA/div
t − Time − 500 ms/div
VI(EN)
5 V/div
IO(OUT)
500 mA/div
470 mF
100 mF
220 mF
VIN = 5 V
RL = 5 W,
TA = 255C
t − Time − 1 ms/div
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 4. Turnon Delay and Rise Time With 100- µ F Load Figure 5. Turnoff Delay and Fall Time With 100- µ F Load
Figure 6. Short-Circuit Current, Figure 7. Inrush Current With DifferentDevice Enabled Into Short Load Capacitance
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
VO(OC)
2 V/div
IO(OUT)
1 A/div
t − Time − 2 ms/div
VO(OC)
2 V/div
IO(OUT)
1 A/div
t − Time − 2 ms/div
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 8. 2- ΩLoad Connected to Enabled Device Figure 9. 1- ΩLoad Connected to Enabled Device
8Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
TYPICAL CHARACTERISTICS
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
23456
Turnon Time − ms
VI − Input Voltage − V
CL = 100 mF,
RL = 5 W,
TA = 255C
1.5
1.6
1.7
1.8
1.9
2
23456
CL = 100 mF,
RL = 5 W,
TA = 255C
Turnoff Time − mS
VI − Input Voltage − V
0
0.1
0.2
0.3
0.4
0.5
0.6
2 3 4 5 6
Rise Time − ms
VI − Input Voltage − V
CL = 1 mF,
RL = 5 W,
TA = 255C
0
0.05
0.1
0.15
0.2
0.25
2 3 4 5 6
CL = 1 mF,
RL = 5 W,
TA = 255C
Fall Time − ms
VI − Input Voltage − V
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
TURNON TIME TURNOFF TIMEvs vsINPUT VOLTAGE INPUT VOLTAGE
Figure 10. Figure 11.
RISE TIME FALL TIMEvs vsINPUT VOLTAGE INPUT VOLTAGE
Figure 12. Figure 13.
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
0
10
20
30
40
50
60
−50 0 50 100 150
VI = 5.5 V
VI = 3.3 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Enabled −
II (IN) Aµ
VI = 5 V
0
10
20
30
40
50
60
70
−50 0 50 100 150
VI = 5.5 V
VI = 5 V
VI = 3.3 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Enabled −
II (IN) Aµ
T − JunctionT
Jemperature − C
o
I − Off-StateCurrent − Am
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
−50 0 50 100 150
T − JunctionT
Jemperature − C
o
I − Off-StateCurrent − Am
0
1
2
3
4
5
6
7
10
−50 0 50 100 150
8
9
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TPS2061, TPS2065-1 TPS2062-1, TPS2066-1SUPPLY CURRENT, OUTPUT ENABLED SUPPLY CURRENT, OUTPUT ENABLEDvs vsJUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 14. Figure 15.
TPS2065-1 TPS2062-1, TPS2066-1SUPPLY CURRENT, OUTPUT DISABLED SUPPLY CURRENT, OUTPUT DISABLEDvs vsJUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 16. Figure 17.
10 Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
1.34
1.36
1.38
1.4
1.42
1.44
1.48
1.5
1.52
1.54
1.56
−50 0 50 100 150
1.46
VI = 3.3 V
VI = 5 V
VI = 3.3 V
VI = 5.5 V
TJ − Junction Temperature − 5C
− Short-Circuit Output Current − A
IOS
VI = 2.7 V
0
20
40
60
80
100
120
−50 0 50 100 150
Out1 = 5 V
Out1 = 3.3 V
Out1 = 2.7 V
IO = 0.5 A
TJ − Junction Temperature − 5C
rDS(on) − Static Drain-Source
On-State Resistance − mΩ
2.1
2.14
2.18
2.22
2.26
2.3
−50 0 50 100 150
UVLO Rising
UVLO Falling
UVOL − Undervoltage Lockout − V
TJ − Junction Temperature − 5C
1.5
1.7
1.9
2.1
2.3
2.5
2.5 3 3.5 4 4.5 5 5.5 6
TA = 255C
Load Ramp = 1A/10 ms
Threshold Trip Current − A
VI − Input Voltage − V
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
TYPICAL CHARACTERISTICS (continued)
STATIC DRAIN-SOURCE ON-STATE RESISTANCE SHORT-CIRCUIT OUTPUT CURRENTvs vsJUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 18. Figure 19.
THRESHOLD TRIP CURRENT UNDERVOLTAGE LOCKOUTvs vsINPUT VOLTAGE JUNCTION TEMPERATURE
Figure 20. Figure 21.
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
0
50
100
150
200
0 2.5 5 7.5 10 12.5
Current-Limit Response − sµ
Peak Current − A
VI = 5 V,
TA = 255C
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
TYPICAL CHARACTERISTICS (continued)
CURRENT-LIMIT RESPONSE
vsPEAK CURRENT
Figure 22.
12 Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
APPLICATION INFORMATION
POWER-SUPPLY CONSIDERATIONS
IN
OC1
EN1
OC2
2
8
5
7
0.1 µF 22 µF
0.1 µF 22 µF
Load
Load
OUT1
OUT2
PowerSupply
2.7Vto5.5V
6
EN2
3
4
GND
0.1 µF
TPS2062-1
1
OVERCURRENT
OC RESPONSE
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
Figure 23. Typical Application
A 0.01- µF to 0.1- µF ceramic bypass capacitor between IN and GND, close to the device, is recommended.Placing a high-value electrolytic capacitor on the output pin(s) is recommended when the output load is heavy.This precaution reduces power-supply transients that may cause ringing on the input. Additionally, bypassing theoutput with a 0.01- µF to 0.1- µF ceramic capacitor improves the immunity of the device to short-circuit transients.
A sense FET is employed to check for overcurrent conditions. Unlike current-sense resistors, sense FETs do notincrease the series resistance of the current path. When an overcurrent condition is detected, the devicemaintains a constant output current and reduces the output voltage accordingly. Complete shutdown occurs onlyif the fault is present long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted before thedevice is enabled or before V
I(IN)
has been applied (see Figure 15 ). The TPS206x-1 senses the short andimmediately switches into a constant-current output.
In the second condition, a short or an overload occurs while the device is enabled. At the instant the overloadoccurs, high currents may flow for a short period of time before the current-limit circuit can react. After thecurrent-limit circuit has tripped (reached the overcurrent trip threshold), the device switches into constant-currentmode.
In the third condition, the load has been gradually increased beyond the recommended operating current. Thecurrent is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device isexceeded (see Figure 17 ). The TPS206x-1 is capable of delivering current up to the current-limit thresholdwithout damaging the device. Once the threshold has been reached, the device switches into its constant-currentmode.
The OCx open-drain output is asserted (active low) when an overcurrent or overtemperature shutdown conditionis encountered after a 10-ms deglitch timeout. The output remains asserted until the overcurrent orovertemperature condition is removed. Connecting a heavy capacitive load to an enabled device can cause amomentary overcurrent condition; however, no false reporting on OCx occurs due to the 10-ms deglitch circuit.The TPS206x-1 is designed to eliminate false overcurrent reporting. The internal overcurrent deglitch eliminatesthe need for external components to remove unwanted pulses. OCx is not deglitched when the switch is turnedoff due to an overtemperature shutdown.
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
GND
IN
EN1
EN2
OC1
OC2
OUT1
OUT2
TPS2062-1 Rpullup
V+
POWER DISSIPATION AND JUNCTION TEMPERATURE
THERMAL PROTECTION
UNDERVOLTAGE LOCKOUT (UVLO)
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
Figure 24. Typical Circuit for the OC Pin
The low on-resistance on the N-channel MOSFET allows the small surface-mount packages to pass largecurrents. The thermal resistances of these packages are high compared to those of power packages; it is gooddesign practice to check power dissipation and junction temperature. Begin by determining the r
DS(on)
of theN-channel MOSFET relative to the input voltage and operating temperature. As an initial estimate, use thehighest operating ambient temperature of interest and read r
DS(on)
from Figure 18 . Using this value, the powerdissipation per switch can be calculated by:P
D
= r
DS(on)
× I
2
Multiply this number by the number of switches being used. This step renders the total power dissipation fromthe N-channel MOSFETs.
Finally, calculate the junction temperature:T
J
= P
D
× R
θJA
+ T
A
Where:
T
A
= Ambient temperature ° CR
θJA
= Thermal resistanceP
D
= Total power dissipation based on number of switches being used.
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generallysufficient to get a reasonable answer.
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present forextended periods of time. The TPS206x-1 implements a thermal sensing to monitor the operating junctiontemperature of the power distribution switch. In an overcurrent or short-circuit condition, the junction temperaturerises due to excessive power dissipation. Once the die temperature rises to approximately 140 ° C due toovercurrent conditions, the internal thermal sense circuitry turns the power switch off, thus preventing the powerswitch from damage. Hysteresis is built into the thermal sense circuit, and after the device has cooledapproximately 10 ° C, the switch turns back on. The switch continues to cycle in this manner until the load fault orinput power is removed. The OCx open-drain output is asserted (active low) when an overtemperature shutdownor overcurrent occurs.
An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the inputvoltage falls below approximately 2 V, the power switch is quickly turned off. This facilitates the design ofhot-insertion systems where it is not possible to turn off the power switch before input power is removed. TheUVLO also keeps the switch from being turned on until the power supply has reached at least 2 V, even if theswitch is enabled. On reinsertion, the power switch is turned on, with a controlled rise time to reduce EMI andvoltage overshoots.
14 Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
UNIVERSAL SERIAL BUS (USB) APPLICATIONS
HOST/SELF-POWERED AND BUS-POWERED HUBS
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
The universal serial bus (USB) interface is a 12-Mb/s, or 1.5-Mb/s, multiplexed serial bus designed forlow-to-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). The four-wire USBinterface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided fordifferential data, and two lines are provided for 5-V power distribution.
USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where poweris distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 Vfrom the 5-V input or its own internal power supply.
The USB specification defines the following five classes of devices, each differentiated by power-consumptionrequirements:
•Hosts/self-powered hubs (SPH)•Bus-powered hubs (BPH)•Low-power, bus-powered functions•High-power, bus-powered functions•Self-powered functions
SPHs and BPHs distribute data and power to downstream functions. The TPS206x-1 has higher currentcapability than required by one USB port; so, it can be used on the host side and supplies power to multipledownstream ports or functions.
Hosts and SPHs have a local power supply that powers the embedded functions and the downstream ports (seeFigure 25 ). This power supply must provide from 5.25 V to 4.75 V to the board side of the downstreamconnection under full-load and no-load conditions. Hosts and SPHs are required to have current-limit protectionand must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs, monitors, printers,and stand-alone hubs.
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
IN
OC1
EN1
OC2
EN2
GND
0.1 µF
2
8
3
5
4
7
33 µF
33 µF
GND
1
OUT1
TPS2062-1
PowerSupply
D+
D−
VBUS
GND
D+
D−
VBUS
Downstream
USBPorts
USB
Controller
3.3V 5V
33 µF GND
OUT2
D+
D−
VBUS
33 µF GND
D+
D−
VBUS
6
0.1 µF
0.1 µF
0.1 µF
0.1 µF
LOW-POWER BUS-POWERED AND HIGH-POWER BUS-POWERED FUNCTIONS
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
Figure 25. Typical Four-Port USB Host / Self-Powered Hub
BPHs obtain all power from upstream ports and often contain an embedded function. The hubs are required topower up with less than one unit load. The BPH usually has one embedded function, and power is alwaysavailable to the controller of the hub. If the embedded function and hub require more than 100 mA on power up,the power to the embedded function may need to be kept off until enumeration is completed. This can beaccomplished by removing power or by shutting off the clock to the embedded function. Power switching theembedded function is not necessary if the aggregate power draw for the function and controller is less than oneunit load. The total current drawn by the bus-powered device is the sum of the current to the controller, theembedded function, and the downstream ports, and it is limited to 500 mA from an upstream port.
Both low-power and high-power bus-powered functions obtain all power from upstream ports; low-powerfunctions always draw less than 100 mA; high-power functions must draw less than 100 mA at power up and candraw up to 500 mA after enumeration. If the load of the function is more than the parallel combination of 44 Ωand 10 µ F at power up, the device must implement inrush current limiting (see Figure 26 ). With TPS206x-1, theinternal functions could draw more than 500 mA, which fits the needs of some applications such as motor drivingcircuits.
16 Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
IN
OC1
OC2
2
8
3
5
4
7
0.1 µF 10 µF
Internal
Function
OUT1
PowerSupply
3.3V
EN1
6
0.1 µF 10 µF
OUT2 Internal
Function
0.1 µF
10 µF
USB
Control
GND
VBUS
D−
D+ TPS2062-1
EN2
GND
1
USB POWER-DISTRIBUTION REQUIREMENTS
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
Figure 26. High-Power Bus-Powered Function
USB can be implemented in several ways, and, regardless of the type of USB device being developed, severalpower-distribution features must be implemented.•Hosts/SPHs must:– Current-limit downstream ports– Report overcurrent conditions on USB V
BUS•BPHs must:– Enable/disable power to downstream ports– Power up at < 100 mA– Limit inrush current ( < 44 Ωand 10 µF)•Functions must:– Limit inrush currents– Power up at < 100 mA
The feature set of the TPS206x-1 allows them to meet each of these requirements. The integratedcurrent-limiting and overcurrent reporting is required by hosts and self-powered hubs. The logic-level enable andcontrolled rise times meet the need of both input and output ports on bus-powered hubs, as well as the inputports for bus-powered functions (see Figure 27 ).
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
DP1
DM1
DP2
DM2
DP3
DM3
DP4
PWRON1
OVRCUR1
PWRON2
OVRCUR2
DM4
DP0
DM0
VCC
XTAL1
XTAL2
OCSOFF
SN75240
D+
D −
5V
GND
D+
D −
5V
D+
D −
5V
D+
D −
5V
48-MHz
Crystal
Downstream
Ports
TUSB2040
HubController
Tuning
Circuit
A
B
C
D
33 µF†
SN75240
A
B
C
D
GND
GND
GND
33 µF†
33 µF†
33 µF†
D+
D −
Upstream
Port
TPS2041B
SN75240
A
B
5V
GND
C
D
1 µF
IN
GND
FerriteBeads
FerriteBeads
FerriteBeads
FerriteBeads
BUSPWR
GANGED
TietoTPS2041EN Input
OC EN
OUT
5-VPower
Supply
IN
GND
3.3V
4.7 µF
0.1 µF
4.7 µF
EN1
IN
OC1
OUT1
TPS2062-1
EN2
OC2
OUT2
0.1 µF
GND
Note:USBrev1.1requires120 mFperhub.
TPS76333
GENERIC HOT-PLUG APPLICATIONS
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
Figure 27. Hybrid Self / Bus-Powered Hub Implementation
In many applications it may be necessary to remove modules or pc boards while the main unit is still operating.These are considered hot-plug applications. Such implementations require the control of current surges seen bythe main power supply and the card being inserted. The most effective way to control these surges is to limit andslowly ramp the current and voltage being applied to the card, similar to the way in which a power supplynormally turns on. Due to the controlled rise times and fall times of the TPS206x-1, these devices can be used toprovide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature of theTPS206x-1 also ensures that the switch is off after the card has been removed, and that the switch is off duringthe next insertion. The UVLO feature insures a soft start with a controlled rise time for every insertion of the cardor module.
18 Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
Power
Supply
0.1 µF
1000 µF
Optimum
2.7Vto5.5V
PCBoard
OvercurrentResponse
TPS2062-1
OC1
GND
EN1
IN
EN2
OUT1
OUT2
OC2
Blockof
Circuitry
Blockof
Circuitry
DETAILED DESCRIPTION
Power Switch
Charge Pump
Driver
Enable ( ENx or ENx)
Overcurrent ( OCx)
TPS2062-1
TPS2065-1
TPS2066-1
www.ti.com
................................................................................................................................................ SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009
Figure 28. Typical Hot-Plug Implementation
By placing the TPS206x-1 between the V
CC
input and the rest of the circuitry, the input power reaches thesedevices first after insertion. The typical rise time of the switch is approximately 1 ms, providing a slow voltageramp at the output of the device. This implementation controls system surge currents and provides ahot-plugging mechanism for any device.
The power switch is an N-channel MOSFET with a low on-state resistance. Configured as a high-side switch, thepower switch prevents current flow from OUT to IN and IN to OUT when disabled. The power switch supplies aminimum current of 1 A.
An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gateof the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requireslittle supply current.
The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associatedelectromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and falltimes of the output voltage.
The logic enable disables the power switch and the bias for the charge pump, driver, and other circuitry to reducethe supply current. The supply current is reduced to less than 1 µA when a logic high is present on ENx, or whena logic low is present on ENx. A logic zero input on ENx, or a logic high input on ENx restores bias to the driveand control circuits and turns the switch on. The enable input is compatible with both TTL and CMOS logiclevels.
The OCx open-drain output is asserted (active low) when an overcurrent or overtemperature condition isencountered. The output remains asserted until the overcurrent or overtemperature condition is removed. A10-ms deglitch circuit prevents the OCx signal from oscillation or false triggering. If an overtemperature shutdownoccurs, the OCx is asserted instantaneously.
Copyright © 2007 – 2009, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
Current Sense
Thermal Sense
Undervoltage Lockout
Discharge Function
TPS2062-1
TPS2065-1
TPS2066-1
SLVS714A – FEBRUARY 2007 – REVISED MARCH 2009 ................................................................................................................................................
www.ti.com
A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently thanconventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitrysends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power FET into itssaturation region, which switches the output into a constant-current mode and holds the current constant whilevarying the voltage on the load.
The TPS206x-1 implements a thermal sensing to monitor the operating temperature of the power distributionswitch. In an overcurrent or short-circuit condition the junction temperature rises. When the die temperature risesto approximately 140 ° C due to overcurrent conditions, the internal thermal sense circuitry turns off the switch,thus preventing the device from damage. Hysteresis is built into the thermal sense, and after the device hascooled approximately 10 degrees, the switch turns back on. The switch continues to cycle off and on until thefault is removed. The open-drain false reporting output ( OCx) is asserted (active low) when an overtemperatureshutdown or overcurrent occurs.
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a controlsignal turns off the power switch.
When the device is disabled (when enable is deasserted or during power-up power-down when V
I
< UVLO) thedischarge function is active. The discharge function offers a resistive discharge path for the external storagecapacitor. This is suitable only to discharge filter capacitors for limited time and cannot dissipate steady statecurrents greater than 8 ma.
20 Submit Documentation Feedback Copyright © 2007 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2062-1 TPS2065-1 TPS2066-1
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
TPS2062D-1 ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2062D-1G4 ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2062DR-1 ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2062DR-1G4 ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2065DGN-1 ACTIVE MSOP-
Power
PAD
DGN 8 80 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2065DGN-1G4 ACTIVE MSOP-
Power
PAD
DGN 8 80 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2065DGNR-1 ACTIVE MSOP-
Power
PAD
DGN 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2065DGNR-1G4 ACTIVE MSOP-
Power
PAD
DGN 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2066DGN-1 ACTIVE MSOP-
Power
PAD
DGN 8 80 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2066DGN-1G4 ACTIVE MSOP-
Power
PAD
DGN 8 80 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2066DGNR-1 ACTIVE MSOP-
Power
PAD
DGN 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS2066DGNR-1G4 ACTIVE MSOP-
Power
PAD
DGN 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
PACKAGE OPTION ADDENDUM
www.ti.com 27-Feb-2009
Addendum-Page 1
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 27-Feb-2009
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TPS2062DR-1 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TPS2065DGNR-1 MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1
TPS2066DGNR-1 MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 18-Jul-2011
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TPS2062DR-1 SOIC D 8 2500 340.5 338.1 20.6
TPS2065DGNR-1 MSOP-PowerPAD DGN 8 2500 346.0 346.0 35.0
TPS2066DGNR-1 MSOP-PowerPAD DGN 8 2500 346.0 346.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 18-Jul-2011
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated