TVS Diodes Surface Mount - 1500W > TPSMC series TPSMC Series RoHS Pb e3 Description Uni-directional Bi-directional The TPSMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features * Hi reliability application and automotive grade AEC-Q101 qualified * For surface mounted applications to optimize board space * Low profile package. * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 * EFT protection of data lines in accordance with IEC 61000-4-4 * Built-in strain relief * VBR @TJ= VBR@25C x (1+T Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Peak Pulse Power Dissipation at TA=25C by 10/1000s Waveform (Fig.2)(Note 1), (Note 2) Symbol Value Unit PPPM 1500 W PM(AV) 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 200 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only VF 3.5 V TJ , TSTG -65 to 150 C Power Dissipation on Infinite Heat Sink at TA=50OC Operating Junction and Storage Temperature Range Typical Thermal Resistance Junction to Lead RuJL 15 C/W Typical Thermal Resistance Junction to Ambient RuJA 75 C/W x (TJ - 25)) (T:Temperature Coefficient) * Glass passivated chip junction * 1500W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 1A above 13V * High temperature soldering guaranteed: 260C/10 seconds at terminals * Plastic package is flammability rated V-0 per Underwriters Laboratories * Meet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Functional Diagram Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Bi-directional Cathode Anode Uni-directional 1 (c) 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 TVS Diodes Surface Mount - 1500W > TPSMC series Electrical Characteristics Part Number (Uni) Part Number (Bi) TPSMC12A TPSMC13A TPSMC15A TPSMC16A TPSMC18A TPSMC20A TPSMC22A TPSMC24A TPSMC27A TPSMC30A TPSMC33A TPSMC36A TPSMC39A TPSMC43A TPSMC47A TPSMC51A TPSMC56A TPSMC62A TPSMC68A TPSMC75A TPSMC82A TPSMC91A TPSMC12CA TPSMC13CA TPSMC15CA TPSMC16CA TPSMC18CA TPSMC20CA TPSMC22CA TPSMC24CA TPSMC27CA TPSMC30CA TPSMC33CA TPSMC36CA TPSMC39CA TPSMC43CA TPSMC47CA TPSMC51CA TPSMC56CA TPSMC62CA TPSMC68CA TPSMC75CA TPSMC82CA TPSMC91CA UNI BI Reverse Stand off Voltage VR (Volts) 12AA 13AA 15AA 16AA 18AA 20AA 22AA 24AA 27AA 30AA 33AA 36AA 39AA 43AA 47AA 51AA 56AA 62AA 68AA 75AA 82AA 91AA 12CA 13CA 15CA 16CA 18CA 20CA 22CA 24CA 27CA 30CA 33CA 36CA 39CA 43CA 47CA 51CA 56CA 62CA 68CA 75CA 82CA 91CA 10.20 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 30.80 33.30 36.80 40.20 43.60 47.80 53.00 58.10 64.10 70.10 77.80 Marking Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 11.40 12.40 14.30 15.20 17.10 19.00 20.90 22.80 25.70 28.50 31.40 34.20 37.10 40.90 44.70 48.50 53.20 58.90 64.60 71.30 77.90 86.50 12.60 13.70 15.80 16.80 18.90 21.00 23.10 25.20 28.40 31.50 34.70 37.80 41.00 45.20 49.40 53.60 58.80 65.10 71.40 78.80 86.10 95.50 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 For bidirectional type having VR of 10 volts and less, the IR limit is double. (c) 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 2 Maximum Maximum Maximum Clamping Peak Reverse Voltage VC Pulse Leakage IR @ Ipp Current Ipp @ VR (V) (A) (A) 16.7 18.2 21.2 22.5 25.2 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 70.1 77.0 85.0 92.0 103.0 113.0 125.0 91.0 83.5 71.7 67.6 60.3 54.9 49.7 45.8 40.5 36.7 33.3 30.5 28.2 25.6 23.5 21.7 19.7 17.9 16.5 14.8 13.5 12.2 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X TVS Diodes Surface Mount - 1500W > TPSMC series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IT IR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 0.31x0.31" (8.0x8.0mm) Copper Pad Area 1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time continues on next page. 3 (c) 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 TVS Diodes Surface Mount - 1500W > TPSMC series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (C) tr=10sec PM(AV), Steady Sate Power Dissipation (W) Cj (pF) Uni-directional V=0V Uni-directional @VR 100 Bi-directional @VR Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) IFSM - Peak Forward Surge Current (A) 200 180 160 140 120 100 80 60 40 20 0 10 100 Number of Cycles at 60 Hz (c) 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 10/1000sec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 TA - Ambient Temperature (C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only 1 2 50 4.0 Figure 6 - Steady State Power Dissipation Derating Curve Bi-directional V=0V 10 ( ) t-Time (ms) 100000 1000 Half Value IPPM IPPM 0 Figure 5 - Typical Junction Capacitance 10000 Peak Value IPPM 100 175 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 4 150 175 TVS Diodes Surface Mount - 1500W > TPSMC series Soldering Parameters Pre Heat Lead-free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 30 seconds max Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes max. Do not exceed 260C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 Weight 0.007 ounce, 0.21 grams Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity Color band denotes positive end (cathode) except Bidirectional. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22--A111 Dimensions DO-214AB (SMC J-Bend) Cathode Band (for Uni-directional products only) C A B H D F E G J K L I Solder Pads (all dimensions in mm) Dimensions Inches Millimeters Min Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - (c) 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 TVS Diodes Surface Mount - 1500W > TPSMC series Part Numbering System Part Marking System TPSMC XXX C A F Cathode Band 5% VBR VOLTAGE TOLERANCE Littelfuse Logo BI-DIRECTIONAL XXXX VBR VOLTAGE SERIES YMXXX Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Component Package Part number TPSMCxxxXX DO-214AB Packaging Option Quantity 3000 Tape & Reel - 16mm tape/13" reel Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.63 (16.0) 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) (c) 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/10/16 Dimensions are in inches (and millimeters). Direction of Feed