CY62167G/CY62167GE MoBL®
16-Mbit (1M words × 16-bit/2M words × 8-bit)
Static RAM with Error-Correcting Code (ECC)
Cypress Semiconductor Corporation 198 Champion Court San Jose,CA 95134-1709 408-943-2600
Document Number: 001-81537 Rev. *P Revised May 26, 2017
16-Mbit (1M words × 16-bit/2M words × 8-bit) Static RAM with Error-Correcting Code (ECC)
Features
Ultra-low standby current
Typical standby current: 5.5 μA
Maximum standby current: 16 μA
High speed: 45 ns/55 ns
Embedded error-correcting code (ECC) for single-bit error
correction
Wide voltage range: 1.65 V to 2.2 V, 2.2 V to 3.6 V, and
4.5 V to 5.5 V
1.0-V data retention
Transistor-transistor logic (TTL) compatible inputs and outputs
Error indication (ERR) pin to indicate 1-bit error detection and
correction
48-pin TSOP I package configurable as 1M × 16 or 2M × 8
SRAM
Available in Pb-free 48-ball VFBGA and 48-pin TSOP I
packages
Functional Description
CY62167G and CY62167GE are high-performance CMOS,
low-power (MoBL®) SRAM devices with embedded ECC[1]. Both
devices are offered in single and dual chip enable options and in
multiple pin configurations. The CY62167GE device includes an
ERR pin that signals a single-bit error-detection and correction
event during a read cycle.
To access devices with a single chip enable input, assert the chip
enable (CE) input LOW. To access dual chip enable devices,
assert both chip enable inputs – CE1 as LOW and CE2 as HIGH.
To perform data writes, assert the Write Enable (WE) input LOW,
and provide the data and address on the device data pins (I/O0
through I/O15) and address pins (A0 through A19) respectively.
The Byte High Enable (BHE) and Byte Low Enable (BLE) inputs
control byte writes and write data on the corresponding I/O lines
to the memory location specified. BHE controls I/O8 through
I/O15 and BLE controls I/O0 through I/O7.
To perform data reads, assert the Output Enable (OE) input and
provide the required address on the address lines. You can
access read data on the I/O lines (I/O0 through I/O15). To perform
byte accesses, assert the required byte enable signal (BHE or
BLE) to read either the upper byte or the lower byte of data from
the specified address location.
All I/Os (I/O0 through I/O15) are placed in a high-impedance state
when the device is deselected (CE HIGH for a single chip enable
device and CE1 HIGH / CE2 LOW for a dual chip enable device),
or the control signals are de-asserted (OE, BLE, BHE).
These devices have a unique Byte Power-down feature where,
if both the Byte Enables (BHE and BLE) are disabled, the
devices seamlessly switch to the standby mode irrespective of
the state of the chip enables, thereby saving power.
On the CY62167GE devices, the detection and correction of a
single-bit error in the accessed location is indicated by the
assertion of the ERR output (ERR = High). See the Truth Table
– CY62167G/CY62167GE on page 16 for a complete description
of read and write modes.
The CY62167G and CY62167GE devices are available in a
Pb-free 48-pin TSOP I package and 48-ball VFBGA packages.
The logic block diagrams are on page 2.
The device in the 48-pin TSOP I package can also be configured
to function as a 2M words × 8-bit device. Refer to the Pin
Configurations section for details.
For a complete list of related documentation, click here.
Product Portfolio
Product
Features and
Options
(see the Pin
Configurations
section)
Range VCC Range (V) Speed (ns)
Current Consumption
Operating ICC, (mA) Standby, ISB2 (µA)
f = fmax
Typ[2] Max Typ[2] Max
CY62167G(E)18 Single or dual
Chip Enables
Optional ERR pin
Industrial 1.65 V–2.2 V 55 29 32 7 26
CY62167G(E)30 2.2 V–3.6 V 45 29 36 5.5 16
CY62167G(E) 4.5 V–5.5 V
Notes
1. This device does not support automatic write-back on error detection.
2. Typical values are included only for reference and are not guaranteed or tested. Typical values are measured at VCC = 1.8 V (for VCC range of 1.65 V–2.2 V), VCC =3V
(for VCC range of 2.2 V–3.6 V), and VCC = 5 V (for VCC range of 4.5 V–5.5 V), TA = 25 °C.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 2 of 23
1M x 16 /
2M x 8
RAM ARRAY
ROW DECODER
A1
A2
A3
A4
A5
A6
A7
A8
A9
A0
COLUMN DECODER
A10
SENSE AMPS
ECC DECODE
A11
A12
A13
A14
A15
A16
A17
A18
A19
ECC ENCODE DATAIN DRIVERS
I/O0-I/O7
I/O8-I/O15
BHE
WE
OE
BLE
CE2
CE1
BYTE
POWER DOWN
CIRCUIT
CE
BHE
BLE
Logic Block Diagram – CY62167G
1M x 16 /
2M x 8
RAM ARRAY
ROW DECODER
A1
A2
A3
A4
A5
A6
A7
A8
A9
A0
COLUMN DECODER
A10
SENSE AMPS
ECC DECODE
A11
A12
A13
A14
A15
A16
A17
A18
A19
ECC ENCODE DATAIN DRIVERS
I/O0-I/O7
I/O8-I/O15
BHE
WE
OE
BLE
CE2
CE1
BYTE
POWER DOWN
CIRCUIT
CE
BHE
BLE
ERR
Logic Block Diagram – CY62167GE
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 3 of 23
Contents
Pin Configuration – CY62167G ........................................ 4
Pin Configuration – CY62167GE ..................................... 5
Maximum Ratings ............................................................. 7
Operating Range ...............................................................7
DC Electrical Characteristics .......................................... 7
Capacitance ......................................................................9
Thermal Resistance .......................................................... 9
AC Test Loads and Waveforms ....................................... 9
Data Retention Characteristics ..................................... 10
Data Retention Waveform .............................................. 10
Switching Characteristics ..............................................11
Switching Waveforms ....................................................12
Truth Table – CY62167G/CY62167GE ........................... 16
ERR Output – CY62167GE ............................................. 16
Ordering Information ...................................................... 17
Ordering Code Definitions ......................................... 18
Package Diagrams .......................................................... 19
Acronyms ........................................................................ 21
Document Conventions ................................................. 21
Units of Measure .......................................................21
Document History Page ................................................. 22
Sales, Solutions, and Legal Information ...................... 23
Worldwide Sales and Design Support ....................... 23
Products ....................................................................23
PSoC® Solutions ......................................................23
Cypress Developer Community .................................23
Technical Support ..................................................... 23
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 4 of 23
Pin Configuration – CY62167G
Figure 1. 48-ball VFBGA Pinout (Dual Chip Enable without ERR) – CY62167G [3]
Figure 2. 48-pin TSOP I Pinout (Dual Chip Enable without ERR) – CY62167G [3, 4]
WE
A11
A10
A6
A0
CE1
I/O
10
I/O
8
I/O
9
A4
A5
I/O
11
I/O
13
I/O
12
I/O
14
I/O
15
V
SS
A9
A8
OE
Vss
A7
I/O
0
BHE
CE2
A17
BLE
V
CC
I/O
2
I/O
1
I/O
3
I/O
4
I/O
5I/O
6
I/O
7
A15
A14
A13
A
12
A19
A18 NC
3
26
5
4
1
D
E
B
A
C
F
G
H
A16
NC
VCC
A1A2
A3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A15
A14
A13
A12
A11
A10
A9
A8
A19
NC
WE
CE
2
NC
BHE
BLE
A18
A17
A7
A6
A5
A4
A3
A2
A1
A16
BYTE
Vss
I/O15/A20
I/O7
I/O14
I/O6
I/O13
I/O5
I/O12
I/O4
Vcc
I/O11
I/O3
I/O10
I/O2
I/O9
I/O1
I/O8
I/O0
OE
Vss
CE
1
A0
Notes
3. NC pins are not connected internally to the die and are typically used for address expansion to a higher-density device. Refer to the respective datasheets for pin
configuration.
4. Tie the BYTE pin in the 48-pin TSOP I package to VCC to use the device as a 1 M × 16 SRAM. The 48-pin TSOP I package can also be used as a 2 M ×8 SRAM by
tying the BYTE signal to VSS. In the 2 M ×8 configuration, pin 45 is the extra address line A20, while BHE, BLE, and I/O8 to I/O14 pins are not used and can be left floating.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 5 of 23
Pin Configuration – CY62167GE
Figure 3. 48-ball VFBGA Pinout (Single Chip Enable with ERR) – CY62167GE [5, 6]
Figure 4. 48-ball VFBGA Pinout (Dual Chip Enable with ERR) – CY62167GE [5, 6]
WE
A
11
A
10
A
6
A
0
CE
I/O
10
I/O
8
I/O
9
A
4
A
5
I/O
11
I/O
13
I/O
12
I/O
14
I/O
15
V
SS
A
9
A
8
OE
Vss
A
7
I/O
0
BHE
ERR
A
17
BLE
V
CC
I/O
2
I/O
1
I/O
3
I/O
4
I/O
5
I/O
6
I/O
7
A
15
A
14
A
13
A
12
A
19
A
18
NC
3
26
5
4
1
D
E
B
A
C
F
G
H
A
16
NC
V
CC
A
1
A
2
A
3
WE
A
11
A
10
A
6
A
0
CE
1
I/O
10
I/O
8
I/O
9
A
4
A
5
I/O
11
I/O
13
I/O
12
I/O
14
I/O
15
V
SS
A
9
A
8
OE
Vss
A
7
I/O
0
BHE
CE
2
A
17
BLE
V
CC
I/O
2
I/O
1
I/O
3
I/O
4
I/O
5
I/O
6
I/O
7
A
15
A
14
A
13
A
12
A
19
A
18
NC
3
26
5
4
1
D
E
B
A
C
F
G
H
A
16
ERR
V
CC
A
1
A
2
A
3
Note
5. NC pins are not connected internally to the die and are typically used for address expansion to a higher-density device. Refer to the respective datasheets for pin
configuration.
6. ERR is an Output pin. If not used, this pin should be left floating.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 6 of 23
Figure 5. 48-pin TSOP I Pinout (Dual Chip Enable with ERR) – CY62167GE [7, 8]
Pin Configuration – CY62167GE (continued)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A15
A14
A13
A12
A11
A10
A9
A8
A19
NC
WE
CE
2
ERR
BHE
BLE
A18
A17
A7
A6
A5
A4
A3
A2
A1
A16
BYTE
Vss
I/O15/A20
I/O7
I/O14
I/O6
I/O13
I/O5
I/O12
I/O4
Vcc
I/O11
I/O3
I/O10
I/O2
I/O9
I/O1
I/O8
I/O0
OE
Vss
CE
1
A0
Notes
7. NC pins are not connected internally to the die and are typically used for address expansion to a higher-density device. Refer to the respective datasheets for pin
configuration.
8. Tie the BYTE pin in the 48-pin TSOP I package to VCC to use the device as a 1 M ×16 SRAM. The 48-pin TSOP I package can also be used as a 2 M × 8 SRAM by
tying the BYTE signal to VSS. In the 2 M × 8 configuration, pin 45 is the extra address line A20, while the BHE, BLE, and I/O8 to I/O14 pins are not used and can be
left floating.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 7 of 23
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage temperature ............................... –65 °C to + 150 °C
Ambient temperature
with power applied .................................. –55 °C to + 125 °C
Supply voltage
to ground potential .............................. –0.5 V to VCC + 0.5 V
DC voltage applied to outputs
in High Z state[9] .................................. –0.5 V to VCC + 0.5 V
DC input voltage[9] .............................. –0.5 V to VCC + 0.5 V
Output current into outputs (LOW) ............................. 20 mA
Static discharge voltage
(MIL-STD-883, Method 3015) ................................. >2001 V
Latch-up current ..................................................... >140 mA
Operating Range
Grade Ambient Temperature VCC[10]
Industrial –40 °C to +85 °C 1.65 V to 2.2 V,
2.2 V to 3.6 V,
4.5 V to 5.5 V
DC Electrical Characteristics
Over the operating range of –40 °C to 85 °C
Parameter Description Test Conditions 45/55 ns Unit
Min Typ [11] Max
VOH Output HIGH
voltage 1.65 V to 2.2 V VCC = Min, IOH = –0.1 mA 1.4 V
2.2 V to 2.7 V VCC = Min, IOH = –0.1 mA 2.0
2.7 V to 3.6 V VCC = Min, IOH = –1.0 mA 2.4
4.5 V to 5.5 V VCC = Min, IOH = –1.0 mA 2.4
4.5 V to 5.5 V VCC = Min, IOH = –0.1 mA VCC – 0.4[12] ––
VOL Output LOW
voltage 1.65 V to 2.2 V VCC = Min, IOL = 0.1 mA 0.2
2.2 V to 2.7 V VCC = Min, IOL = 0.1 mA 0.4
2.7 V to 3.6 V VCC = Min, IOL = 2.1 mA 0.4
4.5 V to 5.5 V VCC = Min, IOL = 2.1 mA 0.4
VIH Input HIGH
voltage[9] 1.65 V to 2.2 V 1.4 VCC + 0.2
2.2 V to 2.7 V 1.8 VCC + 0.3
2.7 V to 3.6 V 2.0 VCC + 0.3
4.5 V to 5.5 V 2.2 VCC + 0.5
VIL Input LOW
voltage[9] 1.65 V to 2.2 V –0.2 0.4
2.2 V to 2.7 V –0.3 0.6
2.7 V to 3.6 V –0.3 0.8
4.5 V to 5.5 V –0.5 0.8
IIX Input leakage current GND < VIN < VCC –1.0 +1.0 μA
IOZ Output leakage current GND < VOUT < VCC, Output disabled –1.0 +1.0
ICC VCC operating supply current VCC = Max, IOUT = 0 mA,
CMOS levels f = 22.22 MHz
(45 ns) –29.036.0mA
f = 18.18 MHz
(55 ns) –29.032.0
f = 1 MHz 7.0 9.0
Notes
9. VIL(min) = –2.0 V and VIH(max) = VCC + 2 V for pulse durations of less than 20 ns.
10. Full device AC operation assumes a 100-µs ramp time from 0 to VCC (min) and 200-µs wait time after VCC stabilizes to its operational value.
11. Indicates the value for the center of distribution at 3.0 V, 25 °C and not 100% tested.
12. This parameter is guaranteed by design and is not tested.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 8 of 23
ISB1[13] Automatic Power-down
Current – CMOS Inputs;
VCC = 2.2 V to 3.6 V and
4.5 V to 5.5 V
CE1 > VCC – 0.2 V or CE2 < 0.2 V
or (BHE and BLE) > VCC – 0.2 V,
VIN > VCC – 0.2 V, VIN < 0.2 V,
f = fmax (address and data only),
f = 0 (OE, and WE), VCC = VCC(max)
–5.516.0
μA
Automatic Power-down
Current – CMOS Inputs
VCC = 1.65 V to 2.2 V –7.026.0
ISB2[13] Automatic Power-down
Current – CMOS Inputs
VCC = 2.2 V to 3.6 V and
4.5 V to 5.5 V
CE1 > VCC – 0.2V or
CE2 < 0.2 V or
(BHE and BLE) > V CC – 0.2 V,
VIN > VCC – 0.2 V or
VIN < 0.2 V,
f = 0, VCC = VCC(max)
25 °C 5.5 6.5[14]
40 °C 6.3 8.0[14]
70 °C 8.4 12.0[14]
85 °C 12.0 16.0
Automatic Power-down
Current – CMOS Inputs
VCC = 1.65 V to 2.2 V
CE1 > VCC – 0.2 V or CE2 < 0.2 V
or (BHE and BLE) > VCC – 0.2 V,
VIN > VCC – 0.2 V or VIN < 0.2 V,
f = 0, VCC = VCC(max)
–7.026.0
DC Electrical Characteristics (continued)
Over the operating range of –40 °C to 85 °C
Parameter Description Test Conditions 45/55 ns Unit
Min Typ [11] Max
Notes
13. Chip enables (CE1 and CE2) and BYTE must be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other inputs can be left floating.
14. The ISB2 maximum limits at 25 °C, 40 °C, and 70 °C are guaranteed by design and not 100% tested.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 9 of 23
Capacitance
Parameter [15] Description Test Conditions Max Unit
CIN Input capacitance TA = 25 °C, f = 1 MHz, VCC = VCC(typ) 10.0 pF
COUT Output capacitance 10.0 pF
Thermal Resistance
Parameter [15] Description Test Conditions 48-ball VFBGA 48-pin TSOP I Unit
ΘJA Thermal resistance
(junction to ambient)
Still air, soldered on a 3 × 4.5 inch,
four-layer printed circuit board
31.50 57.99 °C/W
ΘJC Thermal resistance
(junction to case) 15.75 13.42 °C/W
AC Test Loads and Waveforms
Figure 6. AC Test Loads and Waveforms
V
HIGH
V
CC
OUTPUT
R2
30 pF
INCLUDING
JIG AND
SCOPE
GND
90%
10% 90%
10%
Rise Time = 1 V/ns Fall Time = 1 V/ns
OUTPUT V
TH
Equivalent to: THÉVENIN EQUIVALENT
ALL INPUT PULSES
R
TH
R1
Parameters 1.8 V 2.5 V 3.0 V 5.0 V Unit
R1 13500 16667 1103 1800 Ω
R2 10800 15385 1554 990 Ω
RTH 6000 8000 645 639 Ω
VTH 0.80 1.20 1.75 1.77 V
VHIGH 1.8 2.5 3.0 5.0 V
Note
15. Tested initially and after any design or process changes that may affect these parameters.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 10 of 23
Data Retention Characteristics
Over the Operating Range
Parameter Description Conditions Min Typ [16] Max Unit
VDR VCC for data retention 1.0 V
ICCDR[17, 18] Data retention current 1.2 V < VCC < 2.2 V,
CE1 > VCC 0.2 V or CE2 < 0.2 V
or (BHE and BLE) > VCC – 0.2 V,
VIN > VCC 0.2 V or VIN < 0.2 V
7.0 26.0 μA
2.2 V < VCC < 3.6 V or
4.5 V < VCC < 5.5 V,
CE1 > VCC 0.2 V or CE2 < 0.2 V
or (BHE and BLE) > VCC – 0.2 V,
VIN > VCC 0.2 V or VIN < 0.2 V
5.5 16.0 μA
tCDR[19] Chip deselect to data retention
time
–0.0
tR[19, 20] Operation recovery time 45/55 ns
Data Retention Waveform
Figure 7. Data Retention Waveform [21]
Notes
16. Indicates the value for the center of distribution at 3.0 V, 25 °C and not 100% tested.
17. Chip enables (CE1 and CE2) and BYTE must be tied to CMOS levels to meet the ISB1 / ISB2 / ICCDR spec. Other inputs can be left floating.
18. ICCDR is guaranteed only after the device is first powered up to VCC(min) and then brought down to VDR.
19. These parameters are guaranteed by design and are not tested.
20. Full-device operation requires linear VCC ramp from VDR to VCC(min) > 100 μs or stable at VCC(min) > 100 μs.
21. BHE.BLE is the AND of both BHE and BLE. Deselect the chip by either disabling the chip enable signals or by disabling both BHE and BLE.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 11 of 23
Switching Characteristics
Parameter [22] Description 45 ns 55 ns Unit
Min Max Min Max
Read Cycle
tRC Read cycle time 45.0 55.0 ns
tAA Address to data valid/Address to ERR valid 45.0 55.0 ns
tOHA Data hold from address change/ERR hold from address
change 10.0 10.0 ns
tACE CE1 LOW and CE2 HIGH to data valid / CE LOW to ERR
valid
45.0 55.0 ns
tDOE OE LOW to data valid/OE LOW to ERR valid 22.0 25.0 ns
tLZOE OE LOW to Low Z[23, 24] 5.0 5.0 ns
tHZOE OE HIGH to High Z[23, 24, 25] 18.0 18.0 ns
tLZCE CE1 LOW and CE2 HIGH to Low Z[23, 24] 10.0 10.0 ns
tHZCE CE1 HIGH and CE2 LOW to High Z[23, 24, 25] 18.0 18.0 ns
tPU CE1 LOW and CE2 HIGH to power-up[26] 0.0 0.0 ns
tPD CE1 HIGH and CE2 LOW to power-down[26] 45.0 55.0 ns
tDBE BLE/BHE LOW to data valid 45.0 55.0 ns
tLZBE BLE/BHE LOW to Low Z[23] 5.0 5.0 ns
tHZBE BLE/BHE HIGH to High Z[23, 25] 18.0 18.0 ns
Write Cycle [27, 28]
tWC Write cycle time 45.0 55.0 ns
tSCE CE1 LOW and CE2 HIGH to write end 35.0 40.0 ns
tAW Address setup to write end 35.0 40.0 ns
tHA Address hold from write end 0 0 ns
tSA Address setup to write start 0 0 ns
tPWE WE pulse width 35.0 40.0 ns
tBW BLE/BHE LOW to write end 35.0 40.0 ns
tSD Data setup to write end 25.0 25.0 ns
tHD Data hold from write end 0.0 0.0 ns
tHZWE WE LOW to High Z[23, 24, 25] 18.0 20.0 ns
tLZWE WE HIGH to Low Z[23, 24] 10.0 10.0 ns
Notes
22. Test conditions assume signal transition time (rise/fall) of 3 ns or less, timing reference levels of 1.5 V (for VCC > 3 V) and VCC/2 (for VCC < 3 V), and input pulse
levels of 0 to 3 V (for VCC > 3 V) and 0 to VCC (for VCC < 3V). Test conditions for the read cycle use the output loading shown in Figure 6 on page 9, unless specified otherwise.
23. At any temperature and voltage condition, tHZCE is less than tLZCE, tHZBE is less than tLZBE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any device.
24. Tested initially and after any design or process changes that may affect these parameters.
25. tHZOE, tHZCE, tHZBE, and tHZWE transitions are measured when the outputs enter a high-impedance state.
26. These parameters are guaranteed by design and are not tested.
27. The internal write time of the memory is defined by the overlap of WE = VIL, CE1 = VIL, BHE or BLE or both = VIL, and CE2 = VIH. All signals must be ACTIVE to
initiate a write and any of these signals can terminate a write by going INACTIVE. The data input setup and hold timing must refer to the edge of the signal that
terminates the write.
28. The minimum write cycle pulse width for Write Cycle No. 1 (WE Controlled, OE LOW) should be equal to the sum of tHZWE and tSD.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 12 of 23
Switching Waveforms
Figure 8. Read Cycle No. 1 of CY62167G (Address Transition Controlled) [29, 30]
Figure 9. Read Cycle No. 1 of CY62167GE (Address Transition Controlled) [29, 30]
ADDRESS
DATA I/O PREVIOUS DATAOUT
VALID DATAOUT VALID
tRC
tOHA
tAA
ADDRESS
DATA I/O PREVIOUS DATAOUT VALID DATAOUT VALID
tRC
tOHA
tAA
ERR PREVIOUS ERR VALID ERR VALID
tOHA
tAA
Notes
29. The device is continuously selected. OE = VIL, CE = VIL, BHE or BLE, or both = VIL.
30. WE is HIGH for read cycle.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 13 of 23
Figure 10. Read Cycle No. 2 (OE Controlled) [31, 32, 33, 35]
Figure 11. Write Cycle No. 1 (WE Controlled, OE LOW) [32, 34, 35, 33]
Switching Waveforms (continued)
tRC
tHZCE
tPD
tACE
tDOE
tLZOE
tDBE
tLZBE
tLZCE
tPU
HIGH IMPEDANCE DATAOUT VALID HIGH
IMPEDANCE
ADDRESS
CE
OE
BHE/
BLE
DATA I/O
VCC
SUPPLY
CURRENT
tHZOE
tHZBE
ISB
ADDRESS
CE
DATA I/O
tWC
tSCE
tHD
tSD
tBW
BHE/
BLE
tAW tHA
tSA tPWE
tLZWE
tHZWE
WE
DATAIN VALID
Note 36
Notes
31. WE is HIGH for read cycle.
32. For all dual chip enable devices, CE is the logical combination of CE1 and CE2. When CE1 is LOW and CE2 is HIGH, CE is LOW; when CE1 is HIGH or CE2 is LOW,
CE is HIGH.
33. Address valid prior to or coincident with CE LOW transition.
34. The internal write time of the memory is defined by the overlap of WE = VIL, CE1 = VIL, BHE or BLE, or both = VIL, and CE2 = VIH. All signals must be ACTIVE to initiate
a write and any of these signals can terminate a write by going INACTIVE. The data input setup and hold timing must refer to the edge of the signal that terminates the
write.
35. Data I/O is in the high-impedance state if CE = VIH, or OE = VIH, or BHE, and/or BLE = VIH.
36. During this period, the I/Os are in the output state. Do not apply input signals.
37. The minimum write cycle pulse width should be equal to the sum of tHZWE and tSD.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 14 of 23
Figure 12. Write Cycle No. 2 (CE Controlled) [38, 39, 40]
Switching Waveforms (continued)
ADDRESS
CE
WE
BHE/
BLE
DATA I/O
OE
tWC
tSCE
tAW
tSA
tPWE
tHA
tBW
tHD
tHZOE tSD
DATA
IN VALID
Note 41
Notes
38. For all dual chip enable devices, CE is the logical combination of CE1 and CE2. When CE1 is LOW and CE2 is HIGH, CE is LOW; when CE1 is HIGH or CE2 is LOW,
CE is HIGH.
39. The internal write time of the memory is defined by the overlap of WE = VIL, CE1 = VIL, BHE or BLE or both = VIL, and CE2 = VIH. All signals must be ACTIVE to initiate
a write and any of these signals can terminate a write by going INACTIVE. The data input setup and hold timing must refer to the edge of the signal that terminates the
write.
40. Data I/O is in the high-impedance state if CE = VIH, or OE = VIH, or BHE, and/or BLE = VIH.
41. During this period, the I/Os are in output state. Do not apply input signals.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 15 of 23
Figure 13. Write Cycle No. 4 (BHE/BLE Controlled, OE LOW) [42, 43, 44]
Figure 14. Write Cycle No. 5 (WE Controlled) [42, 43, 44]
Switching Waveforms (continued)
DATAIN VALID
ADDRESS
CE
WE
DATA I/O
tWC
tSCE
tAW
tSA tBW
tHA
tHD
tHZWE tSD
BHE/
BLE
tPWE
tLZWE
Note 45
ADDRESS
CE
WE
BHE/BLE
DATA I/O
OE
tWC
tSCE
tAW
tSA tPWE
tHA
tBW
tHD
tHZOE tSD
DATAIN VALID
Note 45
Notes
42. For all dual chip enable devices, CE is the logical combination of CE1 and CE2. When CE1 is LOW and CE2 is HIGH, CE is LOW; when CE1 is HIGH or CE2 is LOW,
CE is HIGH.
43. The internal write time of the memory is defined by the overlap of WE = VIL, CE1 = VIL, BHE or BLE or both = VIL, and CE2 = VIH. All signals must be ACTIVE to
initiate a write and any of these signals can terminate a write by going INACTIVE. The data input setup and hold timing must refer to the edge of the signal that
terminates the write.
44. Data I/O is in the high-impedance state if CE = VIH, or OE = VIH, or BHE, and/or BLE = VIH.
45. During this period, the I/Os are in output state. Do not apply input signals.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 16 of 23
Truth Table – CY62167G/CY62167GE
BYTE [46] CE1CE2WE OE BHE BLE Inputs/Outputs Mode Power Configuration
X[47] HX
[47] X X X X High-Z Deselect/Power-down Standby (ISB) 2M × 8/1M × 16
XX
[47] L X X X X High-Z Deselect/Power-down Standby (ISB) 2M × 8/1M × 16
XX
[47] X[47] X X H H High-Z Deselect/Power-down Standby (ISB)1M × 16
H L H H L L L Data Out (I/O0–I/O15)Read Active (I
CC)1M × 16
HLHHLHL
Data Out (I/O0–I/O7);
High-Z (I/O8–I/O15)
Read Active (ICC)1M × 16
HLHHLLH
High Z (I/O0–I/O7);
Data Out (I/O8–I/O15)Read Active (ICC)1M × 16
H L H H H L H High-Z Output disabled Active (ICC)1M × 16
H L H H H H L High-Z Output disabled Active (ICC)1M × 16
H L H H H L L High-Z Output disabled Active (ICC)1M × 16
H L H L X L L Data In (I/O0–I/O15) Write Active (ICC)1M × 16
HLHLXHL
Data In (I/O0–I/O7);
High-Z (I/O8–I/O15)Write Active (ICC)1M × 16
HLHLXLH
High-Z (I/O0–I/O7);
Data In (I/O8–I/O15)
Write Active (ICC)1M × 16
L L H H L X X Data Out (I/O0–I/O7)ReadActive (I
CC)2M × 8
L L H H H X X High-Z Output disabled Active (ICC)2M × 8
L L H L X X X Data In (I/O0–I/O7) Write Active (ICC)2M × 8
ERR Output – CY62167GE
Output[48] Mode
0 Read operation, no single-bit error in the stored data.
1 Read operation, single-bit error detected and corrected.
High-Z Device deselected / outputs disabled / Write operation
Notes
46. This pin is available only in the 48-pin TSOP I package. Tie the BYTE to VCC to configure the device in the 1M ×16 option. The 48-pin TSOP I package can also be
used as a 2M × 8 SRAM by tying the BYTE signal to VSS.
47. The ‘X’ (Don’t care) state for the chip enables refer to the logic state (either HIGH or LOW). Intermediate voltage levels on these pins is not permitted.
48. ERR is an Output pin. If not used, this pin should be left floating.
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 17 of 23
Ordering Information
Speed
(ns)
Voltage
Range Ordering Code
Package
Diagram
Package Type
(all Pb-free)
Key Features /
Differentiators
ERR Pin /
Ball
Operating
Range
45 2.2 V–3.6 V CY62167GE30-45BV1XI 51-85150 48-ball VFBGA Sing Chip Enable Yes Industrial
CY62167GE30-45BV1XIT
CY62167GE30-45BVXI Dual Chip Enable Yes
CY62167GE30-45BVXIT
CY62167G30-45BVXI No
CY62167G30-45BVXIT
CY62167GE30-45ZXI 51-85183 48-pin TSOP I Dual Chip Enable Yes
CY62167GE30-45ZXIT
CY62167G30-45ZXI No
CY62167G30-45ZXIT
4.5 V–5.5 V CY62167G-45BVXI 51-85150 48-ball VFBGA Dual Chip Enable No
CY62167G-45BVXIT
CY62167G-45ZXI 51-85183 48-pin TSOP I Dual Chip Enable No
CY62167G-45ZXIT
CY62167GE-45ZXI Yes
CY62167GE-45ZXIT
55 1.65 V–2.2 V CY62167GE18-55BVXI 51-85150 48-ball VFBGA Dual Chip Enable Yes
CY62167GE18-55BVXIT
CY62167G18-55BVXI No
CY62167G18-55BVXIT
CY62167G18-55ZXI 51-85183 48-pin TSOP I No
CY62167G18-55ZXIT
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 18 of 23
Ordering Code Definitions
X = blank or T
blank = Bulk; T = Tape and Reel
Temperature Grade: X = I
I = Industrial
Pb-free
X = blank or 1
blank = Dual Chip Enable; 1 = Single Chip Enable
Package Type: XX = BV or Z
BV = 48-ball VFBGA; Z = 48-pin TSOP I
Speed Grade: XX = 45 or 55
45 = 45 ns; 55 = 55ns
Voltage Range: XX = 30 or blank or 18
30 = 3 V typ; blank = 5 V typ; 18 = 1.8 V typ
ERR output: Single-bit error correction indicator
Process Technology: G = 65 nm
Bus Width: 7 = × 16
Density: 6 = 16-Mbit
Family Code: 621 = MoBL® SRAM family
Company ID: CY = Cypress
CY XX XX
621 67GX
-X
XX
EXX
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 19 of 23
Package Diagrams
Figure 15. 48-ball VFBGA (6 × 8 × 1.0 mm) Package Outline, 51-85150
51-85150 *H
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 20 of 23
Figure 16. 48-pin TSOP I (18.4 × 12 × 1.2 mm) Package Outline, 51-85183
Package Diagrams (continued)
4
5
SEE DETAIL A
SEE DETAIL B
STANDARD PIN OUT (TOP VIEW)
REVERSE PIN OUT (TOP VIEW)
3
2X (N/2 TIPS)
B
B
N/2
0.20
D
D1
A
1
2
5
E
A
N/2 +1
2X
2X
B
N
0.10
0.10
SEATING PLANE
C
A1
e9
2X (N/2 TIPS)
0.10 C
A2
DETAIL A
0.08MM M C A-B
SECTION B-B
7c
b1
SEATING PLANE
PARALLEL TO
b6
DETAIL B
BASE METAL
e/2
X = A OR B
X
GAUGE PLAN
E
0.25 BASIC
WITH PLATING
7
L
C
R
(c)
8
c1
1N
N/2 N/2 +1
3. PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN): INK OR LASER MARK.
4. TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
5. DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE
6. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR
MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON LOWER RADIUS OR
7. THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
8. LEAD COPLANARITY SHALL BE WITHIN 0.10mm AS MEASURED FROM THE
9. DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS (mm).
2. PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
1.051.000.95
A2
N
R
0
L
e
c
D1
E
D
b
c1
b1
0.50 BASIC
0.60
0.08
0.50
48
0.20
8
0.70
0.22
0.20
20.00 BASIC
18.40 BASIC
12.00 BASIC
0.10
0.17
0.10
0.17
0.21
0.27
0.16
0.23
A1
A
0.05 0.15
1.20
SYMBOL
MIN. MAX.
DIMENSIONS
NOM.
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE
MOLD PROTRUSION ON E IS 0.15mm PER SIDE AND ON D1 IS 0.25mm PER SIDE.
PROTRUSION SHALL BE 0.08mm TOTAL IN EXCESS OF b DIMENSION AT MAX.
THE FOOT. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD
TO BE 0.07mm .
0.10mm AND 0.25mm FROM THE LEAD TIP.
SEATING PLANE.
10. JEDEC SPECIFICATION NO. REF: MO-142(D)DD.
51-85183 *F
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 21 of 23
Acronyms Document Conventions
Units of Measure
Acronym Description
BHE Byte High Enable
BLE Byte Low Enable
CE Chip Enable
CMOS Complementary metal oxide semiconductor
I/O Input/output
OE Output Enable
SRAM Static random access memory
TSOP Thin small outline package
VFBGA Very fine-pitch ball grid array
WE Write Enable
Symbol Unit of Measure
°C degree Celsius
MHz megahertz
μAmicroampere
μsmicrosecond
mA milliampere
mm millimeter
ns nanosecond
Ωohm
%percent
pF picofarad
Vvolt
Wwatt
CY62167G/CY62167GE MoBL®
Document Number: 001-81537 Rev. *P Page 22 of 23
Document History Page
Document Title: CY62167G/CY62167GE MoBL®, 16-Mbit (1M words × 16-bit/2M words × 8-bit) Static RAM with
Error-Correcting Code (ECC)
Document Number: 001-81537
Rev. ECN No. Orig. of
Change
Submission
Date Description of Change
*M 4791835 NILE 06/15/2015 Changed status from Preliminary to Final.
*N 5027105 NILE 11/25/2015 Updated DC Electrical Characteristics:
Changed minimum value of VOH parameter from 2.2 V to 2.4 V
corresponding to Operating Range “2.7 V to 3.6 V” and
Test Condition “VCC = Min, IOH = –1.0 mA”.
*O 5439177 VINI 09/16/2016 Updated DC Electrical Characteristics:
Changed minimum value of VIH parameter from 2.0 V to 1.8 V
corresponding to Operating Range “2.2 V to 2.7 V”.
Updated Note 9 (Replaced 2 ns with 20 ns).
Updated Ordering Information:
Updated part numbers.
Updated Ordering Code Definitions.
Updated to new template.
*P 5751153 VINI 05/26/2017 Updated Package Diagrams:
spec 51-85183 – Changed revision from *D to *F.
Updated to new template.
Completing Sunset Review.
Document Number: 001-81537 Rev. *P Revised May 26, 2017 Page 23 of 23
CY62167G/CY62167GE MoBL®
© Cypress Semiconductor Corporation, 2012–2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
ARM® Cortex® Microcontrollers cypress.com/arm
Automotive cypress.com/automotive
Clocks & Buffers cypress.com/clocks
Interface cypress.com/interface
Internet of Things cypress.com/iot
Memory cypress.com/memory
Microcontrollers cypress.com/mcu
PSoC cypress.com/psoc
Power Management ICs cypress.com/pmic
Touch Sensing cypress.com/touch
USB Controllers cypress.com/usb
Wireless Connectivity cypress.com/wireless
PSoC® Solutions
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Forums | WICED IOT Forums | Projects | Video | Blogs |
Training | Components
Technical Support
cypress.com/support