11 December 2014 Page 1 1500W Single Output Power Supply FEATURES Universal AC input with active PFC Programmable output voltage and current High efficiency up to 90% +5V / 0.5A auxiliary output 1.5U profile, high power density RoHS compliant MP1500 Series Forced current sharing for parallel operation Power OK signal ( power good, logic low ) Remote ON-OFF, remote sense function Over voltage, overload, over temperature, short circuit and fan failure protection SPECIFICATION Others Safety & EMC (6) Environmental Function Protections Input Output Model MP1500-1121 MP1500-1151 MP1500-1241 MP1500-1271 MP1500-1481 RoHS compliant DC Voltage Range Rated Current Current Range Rated Power Ripple & Noise (Max.) (2) Voltage Adj. Range Voltage Tolerance (3) Line Regulation Load Regulation Setup, Rise Time Hold Up Time (Typ.) Voltage Range (4) Frequency Range Power Factor (Typ.) Efficiency (Typ.) AC Current (Typ.) Inrush Current (Typ.) Leakage Current Over Load Over Voltage Over Temperature Auxiliary Power Remote ON/OFF Control Power OK Signal Output Voltage Trim Output Current Trim Parallel Operation (5) Working Temp. Working Humidity Storage Temp., Humidity Temp. Coefficient Vibration Safety Standards Withstand Voltage Isolation Resistance EMI Conduction & Radiation Harmonic Current EMS Immunity Cooling Dimension (L*W*H) Packing www.autec.com 12V 125A 0 ~ 125A 1500W 150mVp-p 15V 24V 27V 48V 100A 62.5A 55.5A 31.3A 0 ~ 100A 0 ~ 62.5A 0 ~ 55.5A 0 ~ 31.3A 1500W 1500W 1500W 1500W 150mVp-p 150mVp-p 150mVp-p 150mVp-p 5.0% Typical adjustment by potentiometer. 1.0% 0.5% 1.0% 800ms, 200ms at full load 16ms / 230VAC at full load 90 ~ 264VAC, 127 ~ 370VDC 47 ~ 63Hz EN61000-3-2 ( 0.98/230VAC, 0.99/115VAC at full load ) 87% 88% 89% 89% 90% 18A / 115VAC, 9A / 230VAC 30A / 115VAC, 45A/ 230VAC <2.5mA / 240VAC 105% ~ 110% of rated output power Protection type: Constant current limiting, Latching( Recycle AC power or inhibit ) Variable OVP, 120% 5% Vout. Protection type: Latching ( Recycle AC power or inhibit ) 85C 5C Protection type: O/P voltage shut down ( Auto recovery after temperature decreases ) 5V @ 0.5A (+/- 3%) External switch or NPN Transistor Open drain signal low when PSU turns on, Max. Sink current: 20mA, Max. drain voltage: 40V. Adjustment of output voltage is between 30 ~ 105% of rated voltage Adjustment of output current is between 40 ~ 105% of rated current Please refer to function -25 ~ +60C ( Refer to output load de-rating curve ) 20 ~ 90% R.H non-condensing -40 ~ +85C, 10 ~95% R.H 0.02%/C ( 0 ~ 50C ) 10 ~ 500Hz, 5G 10min./1 cycle, period for 60 min each along X,Y,Z axes Compliance to IEC 60068-2-6-2007 UL 60950-1, 2nd Edition, TUV EN60950-1: 2006+A11 approved I/P-O/P: 3KVAC I/P-FG: 1.5KVAC O/P-FG: 0.5KVAC I/P-O/P, I/P-FG, O/P-FG: 100M / 500VDC EN55022: 2006 Class B EN6100-3-2:2006 Class A, EN61000-3-3: 1995+A1: 2001+A2: 2005 En61204-3: 2000, EN55024: 1998+A1: 2001+A2: 2003 Light industry level, criteria A Controlled by power use & temperature ( Internal ball bearing fan ) 280*127*63.5 mm / 11.02*5.00*2.50 inch 3.2kg ; 6 pcs / 19.2kg / 0.98 CUFT Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 11 December 2014 Page 2 Mechanical Specification Pin Function Description LED Signal Description www.autec.com Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 11 December 2014 Page 3 De-rating Curves Manual Controls www.autec.com Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 11 December 2014 Page 4 Mounting Instructions www.autec.com Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777 11 December 2014 Page 5 Notes 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and a 25C ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance: includes set up tolerance, line regulation and load regulation. 4. De-rating is required under low input voltages. Please check the de-rating curve for more details. 5. One unit may not operate if the total output load is less than 5% of rated load in parallel operation. 6. The power supply is considered a component which will be installed into a system. The final system should be re- confirmed to meet EMC directives. www.autec.com Autec Power Systems Tel: (805)522-0888 667 E Cochran St, Simi Valley, CA93065 Fax: (805)522-8777