UM10698 User manual for I2C-bus RTC demo board OM11059A Rev. 4 -- 2 November 2015 User manual Document information Info Content Keywords PCF85063TP, PCF86063ATL, OM11059A, demoboard, how to get started, I2C-bus, RTC, Real-Time Clock, tuning Abstract User manual for the RTC I2C-bus demoboard OM11059A which contains PCF85063TP and PCF85063ATL UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A Revision history Rev Date Description v.4 20151102 Revised user manual v.3 20140227 Revised user manual v.2 20130404 Revised user manual v.1 20130320 New user manual, first revision Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 2 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 1. Introduction The PCF85063x are a family of CMOS Real-Time Clocks (RTC) and calendar optimized for low power consumption. Different features sets are available. The two version of OM11059A are the ideal evaluation/demo boards to use in the design phase of any project, just power and I2C-bus must be hooked up. A separate demoboard and a user manual are available for the SPI-bus RTC PCF85063BTL: OM11059 and UM10699. 2. Key features There are two RTC variants of the PCF85063x RTC with I2C-bus: PCF85063TP basic functionality with I2C-bus interface PCF85063ATL enhanced functionality with I2C-bus interface 2.1 PCF85063TP The PCF85063TP is a Real-Time Clock with very small form factor, counting seconds, minutes, hours, days, weekdays, months, and years. Electronic oscillator tuning RAM: 1 Byte Package: HWSON8 package: 2 x 3 x 0.5 mm Interrupt: every 30 s or 60 s (e.g. for waking up the microcontroller) Interface: 400 kHz I2C-bus Fig 1. UM10698 User manual Block diagram of the PCF85063TP RTC All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 3 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 2.2 PCF85063ATL The PCF85063ATL is a Real-Time Clock with very small form factor, counting seconds, minutes, hours, days, weekdays, months, and years. Electronic oscillator tuning RAM: 1 Byte Package: HXSON10 package: 2.6 x 2.6 x 0.5 mm Alarm control Timer Interrupt: every 30 s or 60 s, alarm, timer Interface: 400 kHz I2C-bus Clock out: enabled by pin or by software Fig 2. UM10698 User manual Block diagram of the PCF85063ATL RTC All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 4 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 3. Hardware set-up 3.1 General requirements for the RTCs PCF85063TP and PCF85063ATL The RTC circuit just requires one external part: a tuning fork quartz as resonator. The oscillation capacitors are integrated and therefore there is no need for external capacitors. The quartz crystal must be placed close to the RTC circuit, avoiding long lines which may pick up noise. Avoid any tracks with high frequency signals (fast edges) close to the RTC, quartz, or quartz interconnect. The interface is the standard Fast Mode I2C-bus, operating up to 400 kHz. Adjust pull-up values to match the required interface speed keeping them as high impedance as possible for power system saving. Ensure that the specified minimum requirements of the hold times tLOW and tHIGH are fulfilled. Supply voltage: The RTC is specified from 0.9 V to 5.5 V. The I2C-bus interface is specified from 1.8 V to 5.5 V. It is recommended to have a decoupling capacitor on the VDD-VSS rails close by. Due to the low power consumption of below 1 W, no precautions for heat dissipations are required. CLKOUT can be used to measure the frequency or be used as reference for frequency generation with a PLL. Fig 3. Interfacing to microcontroller UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 5 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 3.2 Demo board OM11059A (original version) U1 = PCF85063TP, U2 = PCF85063ATL. Fig 4. Picture of demo board OM11059A The original version of OM11059A allows to easily demonstrate the operation of the PCF85063x with I2C-bus interface. No need to solder the tiny package to a breadboard 100 mil connector for straight forward connections. Both RTCs are on board and can be selected by setting the jumpers J1 and J2 (see Fig 5). Fig 5. Jumper settings On the market, there are quartzes with different load capacitance CL. 12.5 pF is most common, 7 pF offers however lower power consumption. To evaluate the difference, the PCF85063TP is connected to a quartz with CL=7 pF and the PCF85063ATL is connected to a quartz with 12.5 pF. Also the VDD blocking capacitors are mounted (C1, C2). UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 6 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A Straight forward interfacing: - Set jumper to either PCF85063TP or PCF85063ATL - Connect supply voltage (e.g. 3.3 V): VSS to pin 1, VDD to pin 2 - Connect I2C-bus (pull-up resistor needed): SCL to pin 3, SDA to pin 4 - Communicate to the RTC Fig 6. OM11059A block diagram UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 7 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A Fig 7. OM11059A schematic for PCF85063TP and PCF85063ATL 3.3 Demo board OM11059A (newer version) U1 = PCF85063ATL. Fig 8. Picture of PCF85063ATL demo board OM11059A The 2nd version of OM11059A allows to easily demonstrate the operation of only the popular PCF85063ATL with I2C-bus interface. No need to solder the tiny package to a breadboard 100 mil connector for straight forward connections. UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 8 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A Straight forward interfacing: - Set jumper J1 for operation without current meter; jumper J2 & J3 used to invoke INT and CLKOE - Connect supply voltage (e.g. 3.3 V): VSS (GND) to pin 1, VDD to pin 2 - Connect I2C-bus (pull-up resistor needed): SCA to pin 3, SDL to pin 4 - Communicate to the RTC Fig 9. OM11059A schematic for PCF85063ATL 4. Software set-up 4.1 Functionality The RTC PCF85063TP and PCF85063ATL are controlled via standard I2C-bus interface. Common I2C protocol applies. The interface is the standard Fast Mode I2C-bus, operating up to 400 kHz. Theoretically there is no lower speed limit, however a read or write access to the RTC must be finalized within one second after initiating it, otherwise time counter increments could be lost. During access, the time registers of the RTC are frozen and after the read or write sequence is completed, a seconds increment is executed if required. The clock tracks the actual time from seconds to year. It must be initially set to the correct time of the actual time zone. The days per month and leap year are corrected automatically. Leap years are assumed whenever the year is dividable by 4. The RTC can be programmed to generate an interrupt every 30 seconds or every 60 seconds. UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 9 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A At address byte 03h is a general purpose RAM byte to store temporary information. 4.2 System testing There is a fast mode facility to test the functionality of the RTC; it can be activated by setting the EXT_TEST bit in the Control_1 word. The RTC PCF85063x has a frequency tuning facility; its operation is explained in section RTC tuning. The RTC can stay switched on all the time. There is no need to restart or reset the clock. 4.3 Software instructions for setting the clock 4.3.1 Setting the time Setting the clock to 3.45 pm December 15, 2011: * I2C-bus S Start condition * Slave address 1010 0010 write bit set * Register address 0000 0000 address pointer to status word 0 * Status word 0 set 12 hour mode and select option for 12.5 pF quartz (for the PCF85063ATL) set 12 hour mode and select option for 7 pF quartz (for the PCF85063TP) 0000 0011 0000 0010 * I2C-bus Repeated start condition * Slave address 1010 0010 * Register address 0000 0100 address pointer to seconds register * Seconds 0000 0000 0 Seconds (clock integrity ok MSB OS = 0) * Minutes 0100 0101 45 min * Hours 0010 0011 PM, 3 (clock integrity ok OS = 0) * Days 0001 0101 15th * Weekdays 0000 0100 Thursday (4th day of the week) * Month 0001 0010 December * Year 0001 0001 (20)11 * I2C-bus P Stop condition write bit set 4.3.2 Reading the clock UM10698 User manual * Reading the clock (2 minutes after writing) * I2C-bus S Start condition * Slave address 1010 0010 write bit set * Register address 0000 0100 address pointer to seconds byte (4) * I2C-bus Sr repeated start condition * Slave address 1010 0011 read mode * Read register 4, seconds ........ e.g. 56 Seconds, (clock integrity ok OS = 0) All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 10 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A * Minutes ........ e.g. 45 (Minutes) * Hours ........ e.g. 03 (PM 03h) * Days ........ e.g. 15 (15th) * Weekdays ........ e.g. 04 (Thursday) * Month ........ e.g. 12 (December) * Year ........ e.g. 11 (20)11 * I C-bus P Stop condition 2 5. RTC tuning 5.1 Frequency tuning The 32 kHz quartzes are typically sold with a tolerance at room temperature of either 10 ppm or 20 ppm. 11.5 ppm corresponds to 1 s/day. The quartzes require a characteristic load capacity of either 7 pF or 12.5 pF. Oscillators utilizing 7 pF quartzes feature slightly lower power consumption, where the quartzes of 12.5 pF have largest production quantities. The tracks between quartz and RTC represent also some parasitic capacitances and must be kept short. The PCF85063 has a tuning facility where above tolerances can be compensated. Tuning procedure: * Measure the 32xxx Hz (f) signal at the CLKOUT pin. * The offset is calculated in ppm as f[ppm] = 106 x (f - 32768) / 32768 * Consult the offset table in the data sheet. Take the correction value and write it into the register 02h. * The correction is done by means of inhibition or addition: the oscillator runs at constant speed, then every 2 hours (mode 0) 1 second is corrected to by making it shorter or longer. This is not easily visible at the CLKOUT. * Corrections can also be applied every 4 minutes by using mode 1. This mode will consume slightly more power. The 32 kHz quartzes are of the type tuning fork and feature a parabolic frequency response over temperature. When the application is dominantly used over a limited temperature range, it is often helpful to tune the frequency to be slightly higher at the turn-over point. The error around 25 C (clock goes too fast) is then compensated during the time when temperature is lower or higher. For example, for operation between 5 C and 45 C, tune the clock 8 ppm faster than the value for 25 C would be. (See Fig 5.) UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 11 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A (1) Characteristic if tuned to 32.768 kHz at 25 C. (2) Characteristic if tuned with the positive offset foff. Fig 10. Temperature averaged over application range 5 C to 45 C UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 12 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 6. Legal information 6.1 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. 6.2 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the UM10698 User manual customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Evaluation products -- This product is provided on an "as is" and "with all faults" basis for evaluation purposes only. NXP Semiconductors, its affiliates and their suppliers expressly disclaim all warranties, whether express, implied or statutory, including but not limited to the implied warranties of noninfringement, merchantability and fitness for a particular purpose. The entire risk as to the quality, or arising out of the use or performance, of this product remains with customer. In no event shall NXP Semiconductors, its affiliates or their suppliers be liable to customer for any special, indirect, consequential, punitive or incidental damages (including without limitation damages for loss of business, business interruption, loss of use, loss of data or information, and the like) arising out the use of or inability to use the product, whether or not based on tort (including negligence), strict liability, breach of contract, breach of warranty or any other theory, even if advised of the possibility of such damages. Notwithstanding any damages that customer might incur for any reason whatsoever (including without limitation, all damages referenced above and all direct or general damages), the entire liability of NXP Semiconductors, its affiliates and their suppliers and customer's exclusive remedy for all of the foregoing shall be limited to actual damages incurred by customer based on reasonable reliance up to the greater of the amount actually paid by customer for the product or five dollars (US$5.00). The foregoing limitations, exclusions and disclaimers shall apply to the maximum extent permitted by applicable law, even if any remedy fails of its essential purpose. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 6.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are property of their respective owners. All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 13 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 7. List of figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Block diagram of the PCF85063TP RTC .......... 3 Block diagram of the PCF85063ATL RTC ........ 4 Interfacing to microcontroller ............................. 5 Picture of demo board OM11059A .................... 6 Jumper settings................................................. 6 OM11059A block diagram................................. 7 OM11059A schematic for PCF85063TP and PCF85063ATL .................................................. 8 Picture of PCF85063ATL demo board OM11059A ........................................................ 8 OM11059A schematic for PCF85063ATL ......... 9 Temperature averaged over application range 5 C to 45 C ................................................... 12 UM10698 User manual All information provided in this document is subject to legal disclaimers. Rev. 4 -- 2 November 2015 (c) NXP B.V. 2015. All rights reserved. 14 of 15 UM10698 NXP Semiconductors User manual for I2C-bus RTC demo board OM11059A 8. Contents 1. 2. 2.1 2.2 3. 3.1 3.2 3.3 4. 4.1 4.2 4.3 4.3.1 4.3.2 5. 5.1 6. 6.1 6.2 6.3 7. 8. Introduction ......................................................... 3 Key features ......................................................... 3 PCF85063TP ..................................................... 3 PCF85063ATL ................................................... 4 Hardware set-up .................................................. 5 General requirements for the RTCs PCF85063TP and PCF85063ATL ...................... 5 Demo board OM11059A (original version) ......... 6 Demo board OM11059A (newer version) ........... 8 Software set-up ................................................... 9 Functionality ....................................................... 9 System testing.................................................. 10 Software instructions for setting the clock ........ 10 Setting the time ................................................ 10 Reading the clock ............................................. 10 RTC tuning ......................................................... 11 Frequency tuning ............................................. 11 Legal information .............................................. 13 Definitions ........................................................ 13 Disclaimers....................................................... 13 Trademarks ...................................................... 13 List of figures..................................................... 14 Contents ............................................................. 15 Please be aware that important notices concerning this document and the product(s) described herein, have been included in the section 'Legal information'. (c) NXP B.V. 2015. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 2 November 2015 Document identifier: UM10698 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: NXP: OM11059A,598