G4OAC15A - OPTO 22 - Datasheet.Directory

G4 Digital AC Output Modules

PAGE

DATA SHEET

Form 0252-130503

G4 Digital AC Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2012 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

Features

4000 volts optical isolation (transient)

Built-in LED status indicator

Logic levels of 5, 15, and 24 VDC

Removable fuse

Current rating: 3 amps at 45° C

UL Motor Load rating: 1.5 amps

Ability to withstand one-cycle surge of 80 amps

Operating temperature: -30 °C to 70 °C

Description

Opto 22’s G4 AC output modules are used to control or switch

AC loads. Each module provides up to 4000 volts of optical

isolation (transient) between field outputs and the control

side of the circuit, and each features zero voltage turn-on and

zero current turn-off. All AC output modules are equivalent to

single-pole, single-throw, normally open contacts (Form A,

SPST-NO) except the G4OAC5A5, which is equivalent to a

single-pole, single-throw, normally closed contact (Form B,

SPST-NC).

Each module is equipped with a 4 amp fast-blow fuse. The

fuse breaking capacity is 40 amps at 250 VAC. Current should

be limited to prevent the short circuit current from exceeding

the rated breaking capacity of the fuse.

The G4OAC5MA and the G4OAC5AMA are special modules

featuring a manual-on/manual-off/automatic switch, ideal for

diagnostic testing of control applications.

Typical applications for AC output modules include switching

loads such as AC relays, solenoids, motor starters, heaters,

lamps, and indicators.

Part numbers ending in FM are Factory Mutual approved.

G4OAC5A and

G4OAC5AMA Modules

Part Numbers

Part Description

G4OAC5 G4 AC Output 12–140 VAC, 5 VDC Logic

G4OAC5FM G4 AC Output 12–140 V AC, 5 VDC Logic,

Factory Mutual Approved

G4OAC5A G4 AC Output 24–280 VAC, 5 VDC Logic

G4OAC5AFM G4 AC Output 24–280 V AC, 5 VDC Logic,

Factory Mutual Approved

G4OAC5A5 G4 AC Output 24–280 VAC, 5 VDC Logic

G4OAC5A5FM G4 AC Output 24–280 VAC, 5 VDC Logic

NC, Factory Mutual Approved

G4OAC5MA G4 AC Output 12–140 VAC, 5 VDC Logic

With Manual/Auto Switch

G4OAC5AMA G4 AC Output 24–280 VAC, 5 VDC Logic

With Manual/Auto Switch

G4OAC15 G4 AC Output 12–140 VAC, 15 VDC

Logic

G4OAC15A G4 AC Output 24–280 VAC, 15 VDC

Logic

G4OAC24 G4 AC Output 12–140 VAC, 24 VDC

Logic

G4OAC24A G4 AC Output 24–280 VAC, 24 VDC

Logic

G4 Digital AC Output Modules

PAGE

DATA SHEET

Form 0252-130503

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

Specifications

Units G4OAC5

G4OAC5FM* G4OAC5A

G4OAC5AFM* G4OAC5A5

G4OAC5A5FM* G4OAC5MA G4OAC5AMA

Nominal line voltage VAC 120 120/240 120/240 120 120/240

Output voltage range VAC 12–140 24–280 24–280 12–140 24–280

Key feature — — — Normally closed Diagnostic

switch Diagnostic

switch

Current rating:

At 45 °C ambient

At 70 °C ambient A

UL Motor Load Rating A 1.5 1.5 1.5 1.5 1.5

Isolation input-to-

output (transient):

1 ms

1 minute

volts 4000

1500 4000

1500

Off-state leakage at

nominal voltage (60 Hz) mARMS 5 1.25/2.5 1.25/2.5 5 1.25/2.5

Nominal logic voltage VDC 5 5 5 5 5

Logic voltage range VDC 4–8 4–8 4–8 4–8 4–8

Logic pickup voltage VDC 4 4 4 4 4

Logic dropout voltage VDC 1 1 1 1 1

Logic input current at

nominal logic voltage mA 12 12 12 12 12

Control resistance

(Rc in schematic) ohms 220 220 220 220 220

One-cycle surge A peak 80 80 80 80 80

Turn-on time @ 60 Hz milliseconds ≤8.3** ≤8.3** ≤8.3** ≤8.3** ≤8.3**

Turn-off time @ 60 Hz milliseconds ≤8.3*** ≤8.3*** ≤8.3*** ≤8.3*** ≤8.3***

Peak repetitive voltage VAC 500 5 00 500 500 500

Minimum load current mA 20 20 20 20 20

Output voltage drop

maximum peak V 1.6 1.6 1.6 1.6 1.6

Operating frequency Hz 25–65 25–65 25–65 25–65 25–65

dV/dT-off-state V/micro-

seconds 200 200 200 200 200

dV/dT-commutating -- snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

snubbed for

0.5 power

factor load

Temperature

Operating:

Storage: °C

°C -30 to +70

-30 to +85 -30 to +70

-30 to +85

* Part numbers ending in FM are Factory Mutual approved.

** One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave.

*** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave.

G4 Digital AC Output Modules

G4 Digital AC Output Modules DATA SHEET

Form 0252-130503

PAGE

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

Specifications (cont.)

Units G4OAC15*** G4OAC15A*** G4OAC24*** G4OAC24A***

Nominal line voltage VAC 120 120/240 120 120/240

Output voltage range VAC 12–140 24–280 12–140 24–280

Key feature —————

Current rating:

At 45 °C ambient

At 70 °C ambient A

UL Motor Load Rating A 1.5 1.5 1.5 1.5

Isolation input-to-output (transient):

1 ms

1 minute volts 4000

1500 4000

1500

Off-state leakage at nominal volt-

age (60 Hz) mARMS 5 1.25/2.5 5 1.25/2.5

Logic voltage range VDC 10.5–16 10.5–16 19.5–32 19.5–32

Logic pickup voltage VDC 10.5 10.5 19.5 19.5

Logic dropout voltage VDC 1 1 1 1

Logic input current at nominal logic

voltage mA 15 15 18 18

Control resistance

(Rc in schematic) ohms 1 K 1 K 2.2 K 2.2 K

One-cycle surge A peak 80 80 80 80

Turn-on time @ 60 Hz micro-

seconds ≤8.3* ≤8.3* ≤8.3* ≤8.3*

Turn-off time @ 60 Hz micro-

seconds ≤8.3** ≤8.3** ≤8.3** ≤8.3**

Peak repetitive voltage VAC 500 500 500 500

Minimum load current mA 20 20 20 20

Output voltage drop maximum peak V 1.6 1.6 1.6 1.6

Operating frequency Hz 25–65 25–65 25–65 25–65

dV/dT-off-state V/micro-

second 200 200 200 200

dV/dT-commutating -- snubbed for 0.5

power factor load snubbed for 0.5

power factor load

Temperature

Operating:

Storage: °C

°C -30 to +70

-30 to +85 -30 to +70

-30 to +85

* One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave.

** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave.

*** Not for use with Opto 22 brains.

G4 Digital AC Output Modules

PAGE

DATA SHEET

Form 0252-130503

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

Dimensions

Schematics

More About Opto 22

www.opto22.com • Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Form 1335-121210

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2013 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

Products

Opto 22 develops and manufactures reliable, flexible, easy-to-

use hardware and software products for industrial automation,

energy management, remote monitoring, and data

acquisition applications.

OptoEMU Energy Management System

The easy-to-use OptoEMU Sensor monitors electrical energy

use in your facility and delivers detailed, real-time data you

can see, analyze, and use in building and control systems. The

Sensor can monitor energy data from pulsing meters,

electrical panels or subpanels, and equipment. View energy

data online using a software service or incorporate the data

into your control system for complete energy management.

SNAP PAC System

Designed to simplify the typically complex

process of selecting and applying an

automation system, the SNAP PAC

System consists of four integrated

components:

•SNAP PAC controllers

•PAC Project™ Software Suite

•SNAP PAC brains

•SNAP I/O™

SNAP PAC Controllers

Programmable automation controllers

(PACs) are multifunctional, modular controllers based on

open standards.

Opto 22 has been manufacturing PACs for over two

decades. The standalone SNAP PAC S-series, the rack-mounted

SNAP PAC R-series, and the software-based SoftPAC™ all

handle a wide range of digital, analog, and serial functions for

data collection, remote monitoring, process control, and

discrete and hybrid manufacturing.

SNAP PACs are based on open Ethernet and Internet Protocol

(IP) standards, so you can build or extend a system easily,

without the expense and limitations of proprietary networks

and protocols. Wired+Wireless™ models are also available.

PAC Project Software Suite

Opto 22’s PAC Project Software Suite provides full-featured,

cost-effective control programming, HMI (human machine

interface) development and runtime, OPC server, and

database connectivity software for your SNAP PAC System.

Control programming includes both easy-to-learn flowcharts

and optional scripting. Commands are in plain English;

variables and I/O point names are fully descriptive.

PAC Project Basic offers control and HMI tools and is free for

download on our website, www.opto22.com. PAC Project

Professional, available for separate purchase, adds one

SoftPAC, OptoOPCServer, OptoDataLink, options for controller

redundancy or segmented networking, and support for legacy

Opto 22 serial mistic™ I/O units.

SNAP PAC Brains

While SNAP PAC controllers provide central control and data

distribution, SNAP PAC brains provide distributed intelligence

for I/O processing and communications. Brains offer analog,

digital, and serial functions, including thermocouple

linearization; PID loop control; and optional high-speed digital

counting (up to 20 kHz), quadrature counting, TPO, and pulse

generation and measurement.

SNAP I/O

I/O provides the local connection to sensors and equipment.

Opto 22 SNAP I/O offers 1 to 32 points of reliable I/O per

module, depending on the type of module and your needs.

Analog, digital, and serial modules are all

mixed on the same mounting rack and

controlled by the same processor (SNAP

PAC brain or rack-mounted controller).

Quality

Founded in 1974, Opto 22 has established a

worldwide reputation for high-quality

products. All are made in the U.S.A. at our

manufacturing facility in Temecula,

California. Because we test each product

twice before it leaves our factory, rather

than only testing a sample of each batch,

we can guarantee most solid-state relays

and optically isolated I/O modules for life.

Free Product Support

Opto 22’s California-based Product Support Group offers free,

comprehensive technical support for Opto 22 products. Our

staff of support engineers represents decades of training and

experience. Support is available in English and Spanish by

phone or email, Monday–Friday, 7 a.m. to 5 p.m. PST.

Additional support is always available on our website: how-to

videos, OptoKnowledgeBase, self-training guide,

troubleshooting and user’s guides, and OptoForums.

In addition, hands-on training is available for free at our

Temecula, California headquarters, and you can register online.

Purchasing Opto 22 Products

Opto 22 products are sold directly and through a worldwide

network of distributors, partners, and system integrators. For

more information, contact Opto 22 headquarters at 800-321-

6786 or 951-695-3000, or visit our website at