DMM7510-NFP - KEITHLEY - Datasheet.Directory

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

The Model DMM7510 combines all the advantages

of a precision digital multimeter, a graphical

touchscreen display, and a high speed, high

resolution digitizer to create an industry first:

a graphical sampling multimeter. The digitizer

gives the Model DMM7510 unprecedented signal

analysis flexibility; the five-inch capacitive touch-

screen display makes it easy to observe, interact

with, and explore measurements with “pinch

and zoom” simplicity. This combination of high

performance and high ease of use offers unparal-

leled insight into your test results.

Capture Waveforms with the

Built-in 1MS/sec Digitizer

Capturing and displaying waveforms and tran-

sient events just got easier with the DMM7510’s

voltage or current digitizing function. The built-in 1MS/sec, 18-bit digitizer makes it possible to

acquire waveforms without the need to use a separate instrument. The digitizing functions employ

the same ranges that the DC voltage and current functions use to deliver exceptional dynamic mea-

surement range. In addition, the voltage digitizing function uses the same DC voltage input imped-

ance (10GΩ or 10MΩ) levels to reduce loading significantly on the DUT.

• Precision multimeter with 3½-

to 7½-digit resolution

• 14 PPM basic one-year DCV

accuracy

• 100mV, 1Ω, and 10µA ranges

offer the sensitivity needed for

measuring low level signals

• Make accurate low resistance

measurements with offset

compensated ohms, four-wire,

and dry circuit functions

• Capture and display waveforms

or transients with 1MS/sec

digitizer

• Large internal memory buffer;

store over 11 million readings in

standard mode or 27.5 million

in compact mode

• Auto-calibration feature

improves accuracy and stability

by minimizing temperature and

time drift

• Display more with five-inch,

high resolution touchscreen

interface

• Readings and screen images

can be saved quickly via the

front panel USB memory port

• Multiple connectivity options:

GPIB, USB, and LXI-compliant

LAN interfaces

• Two-year specifications allow

for longer calibration cycles

DMM7510

7½-Digit Graphical Sampling Multimeter

The high speed digitizing function allows

capturing and displaying voltage and

current waveforms.

Advanced triggering options make it possi-

ble to capture a signal at precisely the right

point.

The built-in graphing utility supports displaying and comparing measurements

or waveforms from up to four reading buffers at once.

Graphical sampling DMM

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

Make Demanding Measurements with Confidence

The Model DMM7510’s design makes the most of Keithley’s low level measurement expertise.

Features like the low noise input stage and the 32-bit A-to-D converter allow this instrument to

deliver DC accuracies typically only found in metrology-grade instrumentation—but at about half

the price of those solutions. The Model DMM7510’s 100mV, 10Ω, and 10µA ranges deliver the

sensitivity needed to measure low signals with confidence when characterizing today’s demanding

electronic designs. In addition to one- and two-year accuracy specifications, an auto-calibration

function ensures greater accuracy between calibration cycles.

2µV

1µV

0µV

–1µV

–2µV

Volts

6½ Digit 8½ Digit DMM7510

One Power Line Cycle

Noise Performance

The DMM7510 provides noise performance

equivalent to or better than many 8½-digit DMMs.

Comparison of the Model DMM7510’s 1V DC noise performance with that of typical 6½- and

8½-digit multimeters. All data was taken at 1 NPLC with a low thermal short applied to

the input.

15 Measurement Functions

The DMM7510 provides 15 basic measurement functions. In addition to the digitizing voltage and

current functions, it includes capacitance, ACV and ACI, temperature (RTD, thermistor, and thermo-

couple), 2- and 4-wire resistance, dry circuit ohms, period, frequency, diode test, and DC voltage

ratio. The instrument’s flat menu structure allows for fast configuration and improves usability. Its

intuitive design lets you learn how to operate the instrument and begin making device measurements

faster and with greater confidence.

RTD, Thermistor, Thermocouple

Ordering Information

DMM7510 7½-Digit Graphical

Sampling Multimeter

DMM7510-NFP

7½-Digit Graphical

Sampling Multimeter,

with No Front Panel

DMM7510-RACK

7½-Digit Graphical

Sampling Multimeter,

with No Handle

DMM7510-NFP-RACK

7½-Digit Graphical

Sampling Multimeter,

with No Front Panel

and No Handle

Accessories Supplied

1756 Test Leads

USB-B-1 USB Cable, Type A to

Type B, 1m (3.3 ft)

CA-180-3A

TSP-Link/Ethernet Cable

Documentation CD

DMM7510 QuickStart Guide

Test Script Builder Software

(available at www.keithley.com )

KickStart Startup Software

(available at www.keithley.com)

LabVIEW and IVI Drivers (available

at www.keithley.com)

DMM7510

7½-Digit Graphical Sampling Multimeter

Graphical sampling DMM

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

DMM7510 Measurement Capabilities

DC Voltage

AC Voltage

DC Current

AC Current

Resistance (2-wire)

Resistance (4-wire)

Dry Circuit Resistance

Capacitance

Period

Frequency

Digitize Voltage

Digitize Current

10nV

100nV

Logarithmic Scale

Linear Scale

1pA

1nA

100nΩ

1µΩ

0.1pF

–200°C

–80°C

–200°C

1820°C

150°C

850°C

2µs

3Hz

1µV

0.1nA

1010V

707VRMS

10.1A

1.2GΩ

2.4kΩ

1µΩ1.2GΩ

1.2mF

330ms

500kHz

1010V

10.1A

1f 1p 1n 1µ 1m 1 1k 1M 1G

Thermocouple

Thermistor

3-Wire RTD

4-Wire RTD

–500° 0° 500° 1000° 1500° 2000°

Designed for Higher Testing Productivity

In addition to its advanced touchscreen, the Model DMM7510’s front panel offers a variety of features

that enhance its speed, user-friendliness, and learnability, including a USB 2.0 memory I/O port, a

HELP key, a rotary navigation/control knob, and front/rear input selector button. All front-panel but-

tons are backlit to enhance visibility.

Online HELP is

just a button

press away

Store test

results and

screen images

quickly via

the USB 2.0

Memory port Lower swipe screen

speeds access to

often-used features

Five-inch touchscreen

displays more information

simultaneously

Rotary control knob

offers an alternative to

touchscreen navigation

Front/rear input

selector

ACCESSORIES AVAILABLE

TEST LEADS AND PROBES

1752 Premium Safety Test Lead Kit

1754 2-Wire Universal 10-Piece Test Lead Kit

1756 General Purpose Test Lead Kit

5804 Kelvin (4-Wire) Universal 10-Piece Test Lead Kit

5805 Kelvin (4-Wire) Spring-Loaded Probes

5806 Kelvin Clip Lead Set

5808 Low Cost Single-pin Kelvin Probe Set

5809 Low Cost Kelvin Clip Lead Set

8606 High Performance Modular Probe Kit

8610 Low Thermal Shorting Plug

REPLACEMENT FUSES

DMM7510-FUSE-10A 11A Current Fuse For DMM7510

DMM7510-FUSE-3A 3.5A Current Fuse For DMM7510

CABLES, CONNECTORS, ADAPTERS

CA-18-1 Shielded Dual Banana Cable, 1.2m (4 ft.)

COMMUNICATION INTERFACES & CABLES

KPCI-488LPA IEEE-488 Interface for PCI Bus

KUSB-488B IEEE-488 USB-to-GPIB Interface Adapter

7007-1 Shielded GPIB Cable, 1m (3.2ft)

7007-2 Shielded GPIB Cable, 2m (6.5ft)

CA-180-3A CAT5 Crossover Cable for TSP-Link / Ethernet

USB-B-1 USB Cable, Type A to Type B, 1m (3.3 ft)

TRIGGERING AND CONTROL

2450-TLINK DB-9 to Trigger Link Connector Adapter

8501-1 Trigger Link Cable, DIN-to-DIN, 1m (3.2 ft.)

8501-2 Trigger Link Cable, DIN-to-DIN, 2m (6.5 ft.)

8503 DIN-to-BNC Trigger Cable

RACK MOUNT KITS

4299-8 Single Fixed Rack Mount Kit

4299-9 Dual Fixed Rack Mount Kit

4299-10 Dual Fixed Rack Mount Kit. Mount One

DMM7510 and One Series 26xxB Instrument

4299-11 Dual Fixed Rack Mount Kit. Mount One

DMM7510 and One Instrument from Series

2400, Series 2000, etc.

4299-12 Dual Fixed Rack Mount Kit. Mount One

DMM7510 and One Keysight Instrument.

DMM7510-BenchKit

Ears and Handle for DMM7510-NFP-RACK and

DMM7510-RACK Models

Graphical sampling DMM

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

SERVICES AVAILABLE

EXTENDED WARRANTIES

DMM7510-EW 1 Year Factory Warranty Extended

to 2 Years from Date of Shipment

DMM7510-3Y-EW 1 Year Factory Warranty Extended

to 3 Years from Date of Shipment

DMM7510-5Y-EW 1 Year Factory Warranty Extended

to 5 Years from Date of Shipment

DMM7510-NFP-EW 1 Year Factory Warranty Extended

to 2 Years from Date of Shipment

DMM7510-NFP-3Y-EW 1 Year Factory Warranty Extended

to 3 Years from Date of Shipment

DMM7510-NFP-5Y-EW 1 Year Factory Warranty Extended

to 5 Years from Date of Shipment

CALIBRATION CONTRACTS

C/DMM7510-3Y-17025 KeithleyCare® 3 Year ISO-17025

Calibration Plan

C/DMM7510-3Y-DATA KeithleyCare 3 Year Calibration w/

Data Plan

C/DMM7510-3Y-STD KeithleyCare 3 Year Std Calibration

Plan

C/DMM7510-5Y-17025 KeithleyCare 5 Year ISO-17025

Calibration Plan

C/DMM7510-5Y-DATA KeithleyCare 5 Year Calibration w/

Data Plan

C/DMM7510-5Y-STD KeithleyCare 5 Year Std Calibration

Plan

C/DMM7510-NFP-3Y-17025 KeithleyCare 3 Year ISO-17025

Calibration Plan

C/DMM7510-NFP-3Y-DATA KeithleyCare 3 Year Calibration w/

Data Plan

C/DMM7510-NFP-3Y-STD KeithleyCare 3 Year Std Calibration

Plan

C/DMM7510-NFP-5Y-17025 KeithleyCare 5 Year ISO-17025

Calibration Plan

C/DMM7510-NFP-5Y-DATA KeithleyCare 5 Year Calibration w/

Data Plan

C/DMM7510-NFP-5Y-STD KeithleyCare 5 Year Std Calibration

Plan

C/NEW DATA Calibration Data for New Units

C/NEW DATA ISO ISO-17025 Calibration Data for

New Units

Easily accessible

current fuses

Measure Complete and

External Trigger (Model 8503

BNC Accessory Available)

GPIB interface

Six user-defined

digital I/Os

USB 2.0

interface

LAN/LXI

interface

The rear panel of the DMM7510 provides connections and controls that simplify configuring

multi-instrument test solutions, including input connectors, remote control interfaces (GPIB,

USB 2.0, and LXI/Ethernet), a D-sub 9-pin digital I/O port (for internal/external trigger signals

and handler control), and TSP-Link® jacks for connecting to other TSP-enabled instruments.

Flexible System Integration and Programming

To offer users maximum programming flexibility and simplify configuring multi-instrument test

systems, the DMM7510 includes Keithley’s powerful Test Script Processor (TSP®) system and SCPI

programming mode. The embedded scripting capability allows running powerful test scripts directly

on the instrument, without the need for an external PC controller. These test scripts are complete

test programs based on an easy-to-use yet highly efficient and compact scripting language, Lua

(www.lua.org). Scripts are a collection of instrument control commands and/or program state-

ments. Program statements control script execution and provide facilities such as variables, functions,

branching, and loop control. This allows you to create powerful measurement applications with

significantly reduced development times. Test scripts can contain any sequence of routines that are

executable by conventional programming languages (including decision-making algorithms), so

the instrument can manage every facet of the test without the need to communicate with a PC for

decision-making. This eliminates delays due to GPIB, Ethernet or USB traffic congestion and greatly

improves overall test times.

TSP technology also offers “mainframe-less channel expansion.” The TSP-Link channel expansion bus

and a 100 Base T Ethernet cable allow connecting multiple DMM7510s with other TSP-enabled instru-

ments in a master-slave configuration so they operate as a single integrated system. These instru-

ments include the Model 2450 and Model 2460 Interactive SourceMeter® SMU instruments, Series

2600B SourceMeter SMU instruments, and the Series 3700A Switch/Multimeter systems. TSP-Link

supports up to 32 units per GPIB or IP address, so it’s easy to scale a system to fit the requirements of

an application.

A standard SCPI programming mode supports taking advantage of all of the DMM7510’s new features

when programming remotely. In addition, the instrument is code-compatible with the SCPI language,

which many other DMMs use. This code compatibility avoids the need to rewrite code that is normal-

ly associated with upgrading to a new instrument with new capabilities.

Graphical sampling DMM

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

Free Instrument Control Startup Software

Keithley’s KickStart instrument control startup software lets you begin taking measurements

in minutes.

KickStart combines a wide range of functions to

enhance testing productivity:

• Instrument-specific UI panel

• Manual instrument configuration

• Basic reading display and tabular

viewing of data

• Datalogging

• Native X-Y data graphing

• Panning & zooming

• Basic statistics (native to instrument, mX+b)

• Saving/exporting data

• Connect using any remote interface

(GPIB, USB, LAN)

• Save instrument setups

• Screenshot capture

• Command line dialog box

Ready-to-use Instrument Drivers

Simplify Programming

Need to create your own customized appli-

cation software? Native National Instruments

LabVIEW®, IVI-C, and IVI-COM drivers are avail-

able for downloading at www.keithley.com to

simplify the programming process.

Graphical sampling DMM

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

Specification Conditions

This document contains specifications and supplemental infor-

mation for the Model DMM7510 7½-Digit Graphical Sampling

Multimeter instrument. Specifications are the standards against

which the Model DMM7510 is tested. Upon leaving the factory,

the Model DMM7510 meets these specifications. Supplemental

and typical values are nonwarranted, apply at 23°C (73°F), and

are provided solely as useful information. Measurement accura-

cies are specified at the Model DMM7510 terminals under these

conditions:

• Temperature 23° ±5°C, 5% to 80% relative humidity, non-

condensing.

• After a 90-minute warmup period.

• 1 PLC or 5 PLC; for NPLC settings less than 1 PLC, add appro-

priate ppm of range for peak noise uncertainty from the RMS

noise table.

• Autozero enabled unless otherwise noted.

• Remote sense operation or properly zeroed local operation.

• Calibration period: One year or two years (calibration period

may vary depending on customer requirements).

• TACAL = Ambient temperature of last automatic calibration.

• TCAL = Ambient temperature of last external calibration;

factory calibration performed at 23° ±1°C.

DC Voltage

ACCURACY (INPUT IMPEDANCE AUTO)

Range 1 Resolution

Input

Impedance

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient

100.00000 mV 4 10 nV >10 GΩ or

10 MΩ ±1 % 6 + 9 12 + 9 18 + 9 29 + 9 0.1 + 2.5

1.0000000 V 4 100 nV >10 GΩ or

10 MΩ ±1 % 4 + 1 9 + 2 15+ 2 26 + 2 0.1 + 0.5

10.000000 V 4 1 µV >10 GΩ or

10 MΩ ±1 % 2 + 0.7 9 + 1.2 14 + 1.2 22 + 1.2 0.1 + 0.05

100.00000 V 4 10 µV 10 MΩ ±1 % 8 + 3 (18 + 5) 5 (22 + 5) 5 (30 + 5) 5 (0.15 + 0.05) 5

35 + 5 40 + 5 45 + 5 2.0 + 0.5

1000.0000 V 4, 6 100 µV 10 MΩ ±1 % 8 + 3 (19 + 5) 5 (23 + 5) 5 (31 + 5) 5 (0.15 + 0.05) 5

35 + 5 40 + 5 45 + 4 2.0 + 0.5

RMS NOISE (additional peak noise uncertainty) 7

• Applies to ±ppm of range.

• Peak noise uncertainty is included in DC specifications for ≥1 PLC.

• Add peak noise uncertainty to measurements for <1 PLC.

• Input impedance set to Auto.

Examples:

• 10V at 0.006 PLC: 1.2 (from Accuracy table) + 11 (additional peak noise uncertainty) = 12.2 ppm of range.

• 10V at 1 PLC: 1.2 + 0 = 1.2 ppm of range.

NPLC Digits 100 mV 1 V 10 V 100 V 1000 V

57½ 0.5 0.08 0.06 0.3 0.06

17½ 0.5 0.09 0.07 0.4 0.07

0.2 8 6½ 2 (10) 0.2 (1.6) 0.1 (1.1) 1.1 (9.4) 0.1 (1)

0.2 6½ 2 (12) 0.2 (1.6) 0.1 (1) 1.1 (8.9) 0.2 (1.1)

0.06 5½ 3 (17) 0.4 (2.7) 0.3 (2.1) 3 (17) 0.3 (2.4)

0.006 4½ 6 (42) 3 (18) 1 (11) 20 (100) 3 (18)

0.0005 3½ 30 (220) 20 (150) 20 (130) 120 (690) 20 (150)

DC VOLTAGE SENSE ACCURACY

Accuracy ±(ppm of reading + ppm of range)

Range

24 Hour

TCAL ±1°C

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 9

100.00000 mV 6 + 14 12 + 14 18 + 14 29 + 14 0.1 + 2.5

1.0000000 V 4 + 1.5 9 + 3 15 + 3 26 + 3 0.1 + 0.5

10.00000 V 2 + 1.0 9 + 1.8 14 + 1.8 22 + 1.8 0.1 + 0.05

DC VOLTAGE RATIO

For input signals ≥1% of the range, ratio accuracy = ±[[VINPUT ppm of reading + VINPUT ppm of range * (VINPUT range/VINPUT input)] +

[VSENSE ppm of reading + VSENSE ppm of range * (VSENSE range/VSENSE input)]].

1. 20% overrange on all ranges except 1% for 1000V range.

2. Relative to calibration accuracy.

3. Add per degree from TCAL ±5°C.

4. When properly zeroed using the Rel function with external cables.

5. Specified within 30 days of autocalibration, TOPER ±5°C from TACAL.

6. For signal levels greater than 500V, add 0.02 ppm/V to the ppm of the readings specification for measurements exceeding 500V.

7. Noise values are based on 1000 readings with autozero on and using low thermal 4-wire short. VRMS noise is typical. Additional

peak noise is guaranteed.

8. With line sync on.

9. Add per degree from TCAL ±5°C.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

DC VOLTAGE CHARACTERISTICS

ADC LINEARITY: 1.0 ppm of reading + 1.0 ppm of range.

INPUT IMPEDANCE:

100mV to 10V Ranges: Selectable >10GΩ

<400pF (auto) or 10MΩ ±1% (10MΩ).

100V to 1000V Ranges: 10MΩ ±1%.

INPUT BIAS CURRENT: <50pA at 23°C under the following conditions: Autozero off or input

impedance 10MΩ.

COMMON MODE CURRENT: <2.1µA peak-peak in 1MHz bandwidth.

<100nA peak-peak in 1kHz bandwidth.

COMMON MODE VOLTAGE: 500Vpeak LO terminal to chassis maximum.

DC VOLTAGE AUTOZERO OFF ERROR:

For ±1°C and ≤10 minutes, add ±(8ppm of reading + 15µV).

10. Specifications are for 4-wire resistance, offset compensation on for ≤10kΩ measurements, and

offset compensation off for ≥10kΩ measurements. 1Ω range is 4-wire only. For 2-wire, with

Rel, add 50mΩ to ppm of range uncertainty. Without Rel and with Model 1756 test leads, add

100mΩ to ppm of range uncertainty.

11. 20% overrange on all ranges.

12. Test current with offset compensation off, ±5%.

13. Relative to calibration accuracy.

14. Add per degree from TCAL ±5°C.

15. Specifications are for external cable and load capacitance <1nF.

16. For offset compensation on, add 10ppm uncertainty to ppm of reading.

17. For 4-wire 1MΩ, open lead detector on, add 10 ppm uncertainty to ppm of reading.

18. Specified for <10% lead resistance mismatch in HI and LO.

19. Specifications are for 4-wire resistance, offset compensation on for ≤10kΩ measurements, and

offset compensation off for ≥10kΩ measurements. 1Ω range is 4-wire only. For 2-wire, with

Rel, add 50mΩ to ppm of range uncertainty. Without Rel and with Model 1756 test leads, add

100mΩ to ppm of range uncertainty.

20. 20% overrange on all ranges.

21. Test current with offset compensation off.

22. Relative to calibration accuracy.

23. Add per degree from TCAL ±5°C.

24. Specifications are for external cable and load capacitance <1nF.

25. For offset compensation on, add 10ppm of uncertainty to ppm of reading.

26. For 4-wire, 1MΩ, open lead detection on, add 10ppm uncertainty to ppm of reading.

27. Specified for <10% lead resistance mismatch in HI and LO.

Resistance

ENHANCED ACCURACY (within 30 days of autocalibration, TOPER ±5°C from TACAL) 10

Range 11 Resolution

Test Current 12

(±5%)

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C 13

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 14

1.0000000 Ω 0.1 µΩ 10 mA 15 + 50 30 + 50 30 + 50 30 + 50 0.15 + 0.1

10.000000 Ω 1 µΩ 10 mA 15 + 5 30 + 5 30 + 5 30 + 5 0.15 + 0.1

100.00000 Ω 10 µΩ 1 mA 12 + 4 27 + 4 27 + 4 27 + 4 0.15 + 0.1

1.0000000 kΩ 100 µΩ 1 mA 12 + 3 24 + 3 24 + 3 24 + 3 0.15 + 0.1

10.000000 kΩ 15 1 mΩ100 µA 13 + 3 30 + 3 30 + 3 30 + 3 0.15 + 0.1

100.00000 kΩ 15, 16 10 mΩ 10 µA 13 + 3 30 + 3 30 + 3 30 + 3 0.15 + 0.1

1.0000000 MΩ 15, 17 100 mΩ 10 µA 14 + 3 30 + 4 30 + 4 30 + 4 0.15 + 0.1

10.000000 MΩ 18 1 Ω0.69 µA

10 MΩ150 + 6 200 + 10 200 + 10 200 + 10 70 + 1

100.00000 MΩ 18 10 Ω0.69 µA

10 MΩ800 + 30 2000 + 30 2000 + 30 2000 + 30 385 + 1

1.0000000 GΩ 18 100 Ω0.69 µA

10 MΩ9000 + 100 9000 + 100 9000 + 100 9000 + 100 3000 + 1

ACCURACY 19

Range 20 Resolution

Test Current 21

(±5%)

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C 22

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 23

1 Ω 0.1 µΩ 10 mA 15 + 50 40 + 50 50 + 50 70 + 50 2.5 + 5

10 Ω 1 µΩ 1 mA 15 + 5 40 + 5 50 + 5 70 + 5 2.5 + 0.5

100 Ω 10 µΩ 1 mA 12 + 4 35 + 4 47 + 4 65 + 4 5 + 0.25

1 kΩ 100 µΩ 1 mA 12 + 3 30 + 3 41 + 3 65 + 3 5 + 0.25

10 kΩ 24 1 mΩ100 µA 10 + 3 30 + 3 42 + 3 65 + 3 2.5 + 0.25

100 kΩ 24, 25 10 mΩ 10 µA 13 + 3 38 + 3 50 + 3 65 + 3 5 + 1

1 MΩ 24, 26 100 mΩ 10 µA 14 + 3 38 + 5 50 + 5 65 + 5 5 + 1

10 MΩ 27 1 Ω0.69 µA

10 MΩ150 + 6 200 + 10 400 + 10 600 + 12 70 + 1

100 MΩ 27 10 Ω0.69 µA

10 MΩ800 + 30 2000 + 30 2000 + 30 2600 + 30 385 + 1

1 GΩ 27 100 Ω0.69 µA

10 MΩ9000 + 200 9000 + 200 13000 + 200 14000 + 200 3000 + 1

NORMAL MODE REJECTION

For DC voltage, line frequency ±0.1%.

5 PLC 1 PLC ≤0.2 PLC ≤0.01 PLC

Line Sync On 110 dB 90 dB 45 dB —

Line Sync Off 60 dB 60 dB — —

COMMON MODE REJECTION

For DC voltage and 1kΩ unbalanced in LO terminal; AC CMRR is 70dB.

NPLC 5 1 0.2 ≤ 0.2

Line Sync On On On Off

CMRR 140 dB 140 dB 120 dB 80 dB

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

RESISTANCE OPEN CIRCUIT DC VOLTAGE 28

Range 20 2-wire

Offset compensation off Offset compensation on

4-wire 4-wire

1 Ω–9.2 V 9.5 V

10 Ω9.2 V 9.2 V 9.5 V

100 Ω, 1 kΩ14.0 V 14.2 V 14.3 V

10 kΩ9.5 V 9.5 V 0.0 V

100 kΩ, 1 MΩ12.7 V 14.3 V 0.0 V (100 kΩ range only)

10 MΩ to 1 GΩ6.9 V 6.9 V –

4-WIRE OHMS (≤10kΩ) Offset Compensation On

RMS NOISE (additional peak noise uncertainty) 29

• Applies to ± ppm of range.

• Peak noise uncertainty is included in DC specifications for ≥1 PLC.

• Add peak noise uncertainty to measurements for <1 PLC.

EXAMPLES

• 1kΩ at 0.006 PLC: 3 (from Accuracy table) + 26 (additional peak noise uncertainty) = 29 ppm

of range.

• 1kΩ at 1 PLC: 3 + 0 = 3 ppm of range.

NPLC Digits 1 Ω10 Ω100 Ω1 kΩ10 kΩ

57½ 2.8 0.3 0.3 0.07 0.3

17½ 4.2 0.4 0.4 0.12 0.5

0.2 30 6½ 30 (160) 3 (13) 3 (13) 0.4 (2.6) 1.2 (8.2)

0.2 6½ 50 (250) 5 (22) 5 (22) 0.6 (3.2) 1.2 (8.3)

0.06 5½ 110 (490) 11 (47) 11 (46) 1.1 (6.6) 2 (16)

0.006 4½ 110 (710) 10 (70) 10 (70) 4 (26) 10 (60)

0.0005 3½ 520 (3420) 50 (340) 50 (340) 40 (220) 50 (300)

2-WIRE OHMS

RMS NOISE (additional peak noise uncertainty) 29

• Applies to ± ppm of range.

• Peak noise uncertainty is included in DC specifications for ≥1 PLC.

• Add peak noise uncertainty to measurements for <1 PLC.

EXAMPLES

• 10kΩ at 0.006 PLC: 3 (from Accuracy table) + 5 (50mΩ with Rel ) + 43 (additional peak noise

uncertainty) = 51 ppm of range.

• 10kΩ at 1 PLC: 3 + 5 + 0 = 8 ppm of range.

NPLC Digits 10 Ω100 Ω1 kΩ10 kΩ

57½ 1.1 0.8 0.1 0.2

17½ 0.6 0.6 0.09 0.4

0.2 30 6½ 2 (17) 2 (10) 0.2 (1.5) 0.8 (6.3)

0.2 6½ 2 (17) 2 (14) 0.3 (1.6) 0.8 (6.4)

0.06 5½ 3 (22) 3 (19) 0.4 (3.7) 2 (12)

0.006 4½ 6 (50) 6 (50) 3 (21) 6 (43)

0.0005 3½ 30 (300) 30 (230) 20 (150) 30 (210)

RESISTANCE CHARACTERISTICS

MAXIMUM 4-WIRE OHMS LEAD RESISTANCE: 5Ω per lead for 1Ω range, 10% of range per lead

for 10Ω to 1kΩ ranges; 1kΩ per lead for all other ranges.

OFFSET COMPENSATION: Selectable on 4-wire, 1Ω to 100kΩ ranges.

OPEN LEAD DETECTOR: Default is off.

AUTOZERO OFF ERROR:

For 2-wire ohms, ±1°C and ≤10 minutes, add ±(8ppm of reading) + 1.5mΩ for 10Ω, 15mΩ

for 100Ω and 1kΩ ranges, 150mΩ for 10kΩ range, 1.5Ω for 100 kΩ range, and 15Ω for all

other ranges.

For 4-wire ohms, ±1°C and ≤10 minutes, add ±(8ppm of reading).

INPUT CURRENT LIMIT:

For signals with a magnitude of +12V to +40V or –12V to –40V: ±13mA source or sink, typical.

For signals with a magnitude of greater than +40V or –40V: ±130µA source or sink, typical.

Dry Circuit Resistance

ENHANCED ACCURACY (within 30 days of autocalibration, TOPER ±5ºC from TACAL)

Range 31 Resolution

Test Current 35

(±5%)

Open Circuit

DUT Voltage 32

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C 33

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 years

TCAL ±5°C

Temperature

Coefficient 34

1.000000 Ω1 µΩ10 mA 25 mV 25 + 80 50 + 80 50 + 80 50 + 80 1.5 + 0.1

10.00000 Ω10 µΩ1 mA 25 mV 25 + 80 50 + 80 50 + 80 50 + 80 1.5 + 0.1

100.0000 Ω100 µΩ100 µA 25 mV 25 + 80 90 + 80 90 + 80 90 + 80 1.5 + 0.1

1.000000 kΩ1 mΩ10 µA 25 mV 25 + 80 180 + 80 180 + 80 180 + 80 1.5 + 0.1

10.00000 kΩ10 mΩ5 µA 25 mV 25 + 80 320 + 80 320 + 80 320 + 80 1.5 + 0.1

ACCURACY

Range 31 Resolution

Test Current 35

(±5%)

Open Circuit

DUT Voltage 32

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C 33

90 Day

TCAL ±°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 34

1.000000 Ω1 µΩ10 mA 25 mV 25 + 80 50 + 80 70 + 80 90 + 80 2.5 + 1

10.00000 Ω10 µΩ1 mA 25 mV 25 + 80 50 + 80 70 + 80 90 + 80 5 + 1

100.0000 Ω100 µΩ100 µA 25 mV 25 + 80 90 + 80 140 + 80 200 + 80 2.5 + 1

1.000000 kΩ1 mΩ10 µA 25 mV 25 + 80 180 + 80 400 + 80 600 + 80 5 + 1

10.00000 kΩ10 mΩ5 µA 25 mV 25 + 80 320 + 80 800 + 80 1300 + 80 8 + 1

28. Open circuit voltage is typical, measured from input HI to LO, SHI and SLO open. For 1Ω to

1MΩ ranges using an external digital multimeter (DMM) set to 10MΩ input impedance; for

10MΩ to 1GΩ ranges, set external DMM to >10GΩ input impedance.

29. Noise values are based on 1000 readings with autozero on and using low thermal 4-wire short.

RMS noise is typical. Additional peak noise is guaranteed.

30. With line sync on.

31. 20% overrange on all ranges, except 2.4kΩ for the 10kΩ range.

32. Maximum clamp voltages are DC, typical accuracy is ±20%. Add 20% for offset compensation on.

33. Relative to calibration accuracy.

34. Add per degree from TCAL ±5°C.

35. Test current with offset compensation off.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

RMS NOISE (additional peak noise uncertainty) 36

• Applies to ± ppm of range.

• Peak noise uncertainty is included in DC specifications for ≥1 PLC.

• Add peak noise uncertainty to measurements when < 1 PLC.

EXAMPLES:

• 10Ω at 0.2 PLC: 80 (from Accuracy table) + 230 (additional peak noise uncertainty) = 310 ppm

of range.

• 10Ω at 1 PLC: 80 + 0 = 80 ppm of range.

NPLC Digits 1 Ω10 Ω100 Ω1 kΩ10 kΩ

57½ 10 11 6 5 0.9

17½ 9 9 7 7 0.8

0.2 37 6½ 30 (130) 30 (120) 30 (120) 30 (120) 3 (16)

0.2 6½ 60 (220) 60 (230) 50 (190) 50 (190) 9 (35)

0.06 5½ 70 (350) 70 (350) 50 (290) 50 (280) 20 (90)

0.006 4½ 130 (750) 120 (830) 110 (700) 100 (690) 20 (110)

0.0005 3½ 520 (3550) 530 (3520) 530 (3380) 500 (3370) 100 (670)

DRY CIRCUIT RESISTANCE CHARACTERISTICS

MAXIMUM 4-WIRE OHMS LEAD RESISTANCE:

0.5Ω per lead for 1Ω range.

10% of range per lead for 10Ω to 100Ω ranges.

50Ω per lead for 1kΩ to 10kΩ ranges.

INPUT CURRENT LIMIT: For signals greater than ±20mV, current limited, ±13mA typical.

OFFSET COMPENSATION: Selectable on 1Ω to 10kΩ ranges.

AUTOZERO OFF ERROR: For ±1°C and ≤10 minutes, add ±8 ppm of reading.

DC Current

ENHANCED ACCURACY (within 30 days of autocalibration, TOPER ±5°C from TACAL)

Range 38 Resolution

Maximum

Burden Voltage

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C 39

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 40

10.000000 µA 1 pA 15 mV 30 + 30 75 + 30 75 + 30 75 + 30 0.15 + 0.1

100.00000 µA 10 pA 15 mV 20 + 5 60 + 9 60 + 9 60 + 9 0.15 + 0.1

1.0000000 mA 100 pA 15 mV 30 + 5 60 + 9 60 + 9 60 + 9 0.15 + 0.1

10.000000 mA 1 nA 20 mV 40 + 5 60 + 9 60 + 9 60 + 9 0.15 + 0.1

100.00000 mA 10 nA 200 mV 50 + 18 150 + 30 150 + 30 150 + 30 0.15 + 0.1

1.0000000 A 100 nA 400 mV 150 + 50 400 + 50 400 + 50 400 + 50 0.15 + 0.1

3.000000 A 1 µA 1300 mV 200 + 40 400 + 40 400 + 40 400 + 40 0.15 + 0.1

10.000000 A 41 1 µA 650 mV 700 + 275 800 + 275 1500 + 275 2000 + 275 50 + 10

ACCURACY

Range 38 Resolution

Maximum

Burden

Voltage

Accuracy ±(ppm of reading + ppm of range)

24 Hour

TCAL ±1°C 39

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 40

10.000000 µA 1 pA 15 mV 30 + 30 100 + 30 125 + 40 175 + 50 10 + 8

100.00000 µA 10 pA 15 mV 20 + 5 75 + 12 100 + 15 150 + 20 10 + 3

1.0000000 mA 100 pA 15 mV 30 + 5 75 + 12 100 + 15 150 + 20 10 + 3

10.000000 mA 1 nA 20 mV 40 + 5 75 + 12 100 + 15 150 + 20 10 + 3

100.00000 mA 10 nA 200 mV 50 + 18 300 + 30 400 + 30 500 + 30 50 + 5

1.0000000 A 100 nA 400 mV 150 + 50 400 + 50 450 + 50 500 + 50 10 + 10

3.000000 A 1 µA 1300 mV 200 + 40 400 + 40 450 + 40 500 + 40 10 + 10

10.000000 A 41 1 µA 650 mV 700 + 275 800 + 275 1500 + 275 2000 + 275 50 + 10

36. Noise values are based on 1000 readings with autozero on and using low thermal 4-wire short. RMS noise is typical. Additional peak noise is guaranteed.

37. With line sync on.

38. 20% overrange supported for all ranges except for 3A and 10A, which are 1% supported.

39. Relative to calibration accuracy.

40. Add per degree from TCAL ±5°C.

41. Rear input terminals only.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

RMS NOISE (additional peak noise uncertainty) 42

• Applies to ± ppm of range.

• Peak noise uncertainty is included in DC specifications for ≥1 PLC.

• Add peak noise uncertainty to measurements when <1 PLC.

EXAMPLES:

• 1mA at 0.006 PLC: 9 (from Accuracy table) + 20 (additional peak noise uncertainty) = 29 ppm of range.

• 1mA at 1 PLC: 9 +0 = 9 ppm of range.

NPLC Digits 10 µA 100 µA 1 mA 10 mA 100 mA 1A 3A 10A 43

57½ 0.15 0.14 0.09 0.1 0.3 0.3 0.2 0.8

17½ 0.4 0.13 0.1 0.1 0.5 0.5 0.3 1.2

0.2 6½ 0 (220) 0 (23) 0.2 (3.4) 0.2 (1.6) 2 (10) 2 (11) 0.7 (4.6) 4 (32)

0.2 44 6½ 120 (260) 12 (26) 1.2 (3.8) 0.3 (1.8) 1.9 (9.8) 2 (10) 0.8 (5) 8 (37)

0.06 5½ 130 (280) 12 (29) 1.3 (5.6) 0.4 (3.9) 2 (14) 2 (14) 1.2 ( 7.7 ) 10 (59)

0.006 4½ 130 (350) 14 (42) 3 (20) 2 (20) 4 (30) 4 (31) 7 (51) 20 (110)

0.0005 3½ 260 (2110) 30 (300) 20 (150) 20 (160) 30 (190) 30 (190) 70 (510) 60 (420)

DC CURRENT CHARACTERISTICS

Range 10 µA 100 µA 1 mA 10 mA 100 mA 1 A 3 A 10 A 43

Effective Internal Shunt Value 45 1 kΩ100 Ω10 Ω1 Ω0.1 Ω0.1 Ω0.1 Ω0.005 Ω

Autozero Off Error: For ±1°C and ≤10 minutes add

±(8 ppm of reading + range error) 150 pA 1.5 nA 15 nA 150 nA 15 µA 150 µA 150 µA 3 mA

Overload Recovery: For each additional sustained amp

beyond ±1.5A, add the following initial ppm of range error

until thermally settled after overload recovery

15500 1800 150 150 6500 200 — —

Temperature

4-WIRE RTD OR 3-WIRE RTD

TYPES: 100Ω platinum PT100, D100, F100, PT385, PT3916; or user-configurable 0Ω to 10kΩ.

Type Range Resolution

Accuracy ±°C

2 Year

TCAL ±5°C

Temperature

Coefficient 46

4-Wire RTD –200 to 850 °C 0.01 °C 0.06 °C 0.003 °C/°C

3-Wire RTD 47 –200 to 850 °C 0.01 °C 0.75 °C 0.003 °C/°C

THERMISTOR

TYPES: 2.252kΩ, 5kΩ, and 10kΩ.

Type Range Resolution

Accuracy ±°C

2 Year

TCAL ±5°C

Temperature

Coefficient 46

Thermistor –80 to +150 °C 0.01 °C 0.08 °C 0.002 °C/°C

THERMOCOUPLE

TYPES: B, E, J, K, N, R, S, T

Accuracy ±°C

Type Range Resolution

2 Year, TCAL ±5°C 48

Simulated Reference

Junction

Temperature

Coefficient 46

B350 to +1820 °C 0.1 °C 0.6 °C 0.03 °C/°C

E−200 to +1000 °C 0.001 °C 0.2 °C 0.03 °C/°C

J−200 to +760 °C 0.001 °C 0.2 °C 0.03 °C/°C

K−200 to +1372 °C 0.001 °C 0.2 °C 0.03 °C/°C

N−200 to +1300 °C 0.001 °C 0.2 °C 0.03 °C/°C

R0 to +1768 °C 0.1 °C 0.6 °C 0.03 °C/°C

S0 to +1768 °C 0.1 °C 0.6 °C 0.03 °C/°C

T−100 to +400 °C 0.001 °C 0.2 °C 0.03 °C/°C

42. Noise values are based on 1000 readings with autozero on and AMPS terminal open. RMS

noise is typical. Additional peak noise is guaranteed.

43. Rear input terminals only.

44. With line sync on.

45. Values are typical and guaranteed by design.

46. Add per degree from TCAL ±5°C; specifications without autocalibration.

47. For 3-wire RTD, accuracy is for <0.1Ω lead resistance mismatch for input HI and LO. Add

0.25°C/0.1Ω of HI-LO lead resistance mismatch.

48. Exclusive of cold-junction errors.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

Continuity

Range 49 Resolution

Test

Current

Open

Circuit

Voltage

Accuracy ±(ppm of reading +

ppm of range)

2 Year

TCAL ±5°C

Temperature

Coefficient 50

1.0000 kΩ100 mΩ1 mA 14.0 V 100 + 100 2.5 + 1

CONTINUITY CHARACTERISTICS

CONTINUITY HIGH LIMIT: User-selectable; default 10Ω.

Capacitance

Accuracies specified for additional cable and stray capacitance properly zeroed with the Rel function.

ACCURACY

Range 51 Resolution

Charge

Current 52, 53

Maximum

Circuit

Voltage

Accuracy

±(% of reading + % of range)

2 years

TCAL ±5°C

Temperature

Coefficient 50

1.0000 nF 0.1 pF 1.1 µA 2.8 V 1 + 0.2 0.15 + 0.05

10.000 nF 1 pF 1.1 µA 2.8 V 1 + 0.1 0.15 + 0.01

100.00 nF 10 pF 10 µA 3 V 0.4 + 0.1 0.01 + 0.01

1.0000 µF 0.1 nF 100 µA 3 V 0.4 + 0.1 0.01 + 0.01

10.000 µF 1 nF 100 µA 3 V 0.4 + 0.1 0.01 + 0.01

100.00 µF 10 nF 1 mA 3 V 0.4 + 0.1 0.01 + 0.01

1000.0 µF 0.1 µF 10 mA 3 V 0.5 + 0.1 0.01 + 0.01

49. Specifications exclude lead resistance.

50. Add per degree from TCAL ±5°C; specifications without autocalibration.

51. 20% overrange on all ranges.

52. Charging current values are typical, guaranteed by design.

53. Discharge current limited to <13mA.

54. For DC coupling, 20% overrange for 100mV to 100V. For AC coupling, 500% overrange 100mV

to 100V. 1% for 1000V range DC and AC coupling.

55. Accuracy with sample rate 1k per second, aperture auto, and 100 reading buffer average.

56. Power up default is 4½ digits.

57. User-selectable.

58. Add per degree from TCAL ±5%.

59. For 100V range, input impedance auto and without ACAL, add 100ppm of range additional

uncertainty and 15ppm/°C additional uncertainty for “of range” temperature coefficient for

operation outside of TCAL ±5°C.

60. For signal levels greater than 500V, add 0.02 ppm/V to the ppm of the readings specification

for measurements exceeding 500V.

Diode

Voltage

Measure

Range 51 Resolution

Bias Level

(Selectable)

Accuracy ±(ppm of reading + ppm of range)

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 50

10.000000 V 1 µV 10 µA / 100 µA / 1 mA 20 + 5 30 + 5 45 + 5 2.5 + 1

Digitize Voltage

ACCURACY (Input Impedance AUTO)

Range 54, 55 Resolution 56 Input Impedance 57

Accuracy ±(ppm of reading + ppm of range)

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 58

100.000 mV 1 µV >10 GΩ or 10 MΩ ±1% 210 + 100 220 + 100 230 + 100 15 + 20

1.00000 V 10 µV >10 GΩ or 10 MΩ ±1% 110 + 75 120 + 75 130 + 75 15 + 20

10.0000 V 0.1 mV >10 GΩ or 10 MΩ ±1% 110 + 75 120 + 75 130 + 75 10 + 20

100.000 V 59 1 mV 10 MΩ ±1% 110 + 75 120 + 75 130 + 75 15 + 20

1000.00 V 60 10 mV 10 MΩ ±1% 110 + 75 120 + 75 130 + 75 10 + 20

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

SIGNAL CHARACTERISTICS 61, 62, 63

TYPICAL AC AND DC COUPLED

Range

Analog

Bandwidth

(–3dB)

Maximum Flatness

Error

3 Hz to 20 kHz 64

THD

20 kHz Signal

(–1dB FS) 65

DC-coupled

Settling Time

(0.5%)

AC-coupled Filter

FAST Settling Time

(0.5%)

AC-coupled Filter

SLOW Settling Time

(0.5%)

AC Coupling

Low Frequency

(–3dB) point 66

100.000 mV 600 kHz 0.015 dB 0.04 % 5 µs 80 ms 2.3 s 1 Hz

1.00000 V 600 kHz 0.01 dB 0.03 % 6 µs 80 ms 2.5 s 1 Hz

10.0000 V 600 kHz 0.01 dB 0.01 % 4 µs 80 ms 2.5 s 1 Hz

TYPICAL DC COUPLED

Range

Analog

Bandwidth

(–3dB)

Maximum Flatness

Error

3 Hz to 1 kHz 64

Total Harmonic

Distortion (THD)

1 kHz Signal

(–1dB FS) 65

Settling Time

(0.5%)

100.000 V 20 kHz 67 0.1 dB 1.3 % 160 µs

1000.00 V 20 kHz 0.1 dB 1.8 % 80 µs

TYPICAL AC COUPLED

Range

Analog

Bandwidth

(–3dB)

Maximum Flatness

Error

3 Hz to 20 kHz 64

Filter FAST

Settling Time

(0.5%)

Filter SLOW

Settling Time

(0.5%)

Low Frequency

Coupling Point 66

(–3dB)

100.000 V 600 kHz 0.1 dB 80 ms 2.3 s 1 Hz

1000.00 V 600 kHz 0.1 dB 80 ms 2.3 s 1 Hz

DC-COUPLED ADDITIONAL NOISE UNCERTAINTY, TYPICAL 68

DC-COUPLED TOTAL HARMONIC DISTORTION (THD), TYPICAL 69

0.1

100

1000

1k 2k 5k 10k 20k 50k 100k 200k 500k 1M

ppm of Range

Samples per Second

RMS Noise, Digitize Voltage

100mV

10V

100V

1000V

-120

-110

-100

-90

-80

-70

-60

-50

1k 2k 5k 10k 20k 50k 100k 200k

dB of Range

Samples per Second

Total Harmonic Distortion, Digitize Voltage

100mV

10V

100V

1000V

61. Accuracy with sample rate 1M per second and aperture 1µs.

62. Verified with sine wave input and DC content ≤3% of range.

63. For AC coupling, maximum crest factor of 5.

64. For DC coupled, 0dB reference frequency is 3Hz. For AC coupled, 0dB reference frequency is

1kHz. For AC coupled operation below 1kHz, add 0.1dB.

65. Exclusive of source input noise.

66. With AC coupling frequency = 3Hz and AC coupling filter = Slow.

67. For input impedance auto, bandwidth is 6kHz.

68. Specified with aperture auto and 4-wire short on input terminals. For 100V range, input

impedance 10MΩ, multiply by 2.5. For all ranges and sample rate >1k, add an additional 3×

RMS noise uncertainty to ppm of range.

69. Specified with aperture Auto, 100 Hz sine wave for sample rate ≤ 5 k, and 1 kHz sine wave for

sample rate ≥ 10 k. Distortion is calculated using first five harmonics.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DC-COUPLED EFFECTIVE NUMBER OF BITS (ENOB), TYPICAL 70

1k 2k 5k 10k 20k 50k 100k 200k

Bits

Samples per Second

Effective Number of Bits (ENOB), Digitize Voltage

100mV

10V

Digitize Current

DC ACCURACY 71

Range 72 Resolution 73

Burden

Voltage

Accuracy ± (ppm of reading + ppm of range)

90 Day

TCAL ±5°C

1 Year

TCAL ±5°C

2 Year

TCAL ±5°C

Temperature

Coefficient 74

10.0000 µA 0.1 nA 15 mV 150 + 75 160 + 75 170 + 75 30 + 15

100.000 µA 1 nA 15 mV 150 + 75 160 + 75 170 + 75 30 + 15

1.00000 mA 10 nA 15 mV 150 + 75 160 + 75 170 + 75 30 + 15

10.0000 mA 100 nA 20 mV 150 + 75 160 + 75 170 + 75 30 + 15

100.000 mA 1 µA 200 mV 340 + 100 450 + 100 560 + 100 50 + 20

1.00000 A 10 µA 400 mV 400 + 110 500 + 110 600 + 110 50 + 25

3.00000 A 100 µA 1300 mV 650 + 150 900 + 150 900 + 150 50 + 25

10.0000 A 75 100 µA 650 mV 950 + 350 1500 + 350 2000 + 350 50 + 25

SIGNAL CHARACTERISTICS, TYPICAL 76

Range 72

Maximum Flatness

Error

3 Hz to 20 kHz

Analog Bandwidth

(–3dB)

Total Harmonic

Distortion (THD)

20 kHz Signal

(–1dB FS)

DC-coupled

Settling Time

(0.5%)

10.0000 µA 0.15 dB 100 kHz 0.02 % 8 µs

100.000 µA 0.15 dB 100 kHz 0.01 % 7 µs

1.00000 mA 0.1 dB 100 kHz 0.01 % 3 µs

10.0000 mA 0.1 dB 100 kHz 0.01 % 8 µs

100.000 mA 0.1 dB 100 kHz 0.02 % 5 µs

1.00000 A 77 0.1 dB 100 kHz 0.02 % 6 µs

3.0000 A 77 0.1 dB 100 kHz 0.02 % 6 µs

10.0000 A 75, 77, 78 0.1 dB 100 kHz 0.02 % 6 µs

70. Specified with aperture Auto, 100Hz sine wave for sample rate ≤5k, and 1kHz sine wave

for sample rate ≥10k. For the 100V and 1000V ranges, use the 1V and 10V range ENOB,

respectively; guaranteed by design.

71. Accuracy with sample rate 1k per second, aperture auto, and 100 reading buffer average.

72. 20% overrange on all ranges except 3.3% for 3A and 10A ranges.

73. Power up default is 4½ digits.

74. Add per degree from TCAL ±5°C.

75. Rear input terminals only.

76. Verified with sine wave input and DC content ≤ 3 % of range. 0 dB reference frequency is 3 Hz.

77. 10A range is available only on the rear input terminals.

78. 10A flatness verified to 10kHz; 100kHz guaranteed by design.

DMM7510 7½-Digit Graphical Sampling Multimeter

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

Digitizer Characteristics

MAXIMUM RESOLUTION: 18 bits.

MEASUREMENT INPUT COUPLING: DC or AC (voltage only).

SAMPLING RATE 82: Programmable 1k through 1 million.

VOLATILE SAMPLE MEMORY WITH TIMESTAMP: 27.5 million .

MINIMUM RECORD TIME: 1µs.

TIMESTAMP RESOLUTION: 1ns with standard or full buffer style. 1µs with compact buffer style.

TIMESTAMP ACCURACY:

With standard or full buffer style, 20ns between adjacent readings, with total buffer time <2s.

With compact buffer style, 2µs adjacent readings, with total buffer buffer time <2s.

MAXIMUM RECORD LENGTH: 8 million.

ADDITIONAL NOISE UNCERTAINTY, TYPICAL 79 TOTAL HARMONIC DISTORTION (THD), TYPICAL 80

100

1000

1k 2k 5k 10k 20k 50k 100k 200k 500k 1M

ppm of Range

Samples per Second

RMS Noise, Digitize Current

10µA

100µA

1mA

10mA

100mA, 1A

10A

-120

-110

-100

-90

-80

-70

1k 2k 5k 10k 20k 50k 100k 200k

dB of Range

Samples per Second

Total Harmonic Distortion, Digitize Current

10µA

100µA

1mA

10mA

100mA

EFFECTIVE NUMBER OF BITS (ENOB), TYPICAL 81

1k 2k 5k 10k 20k 50k 100k 200k

Bits

Samples per Second

Effective Number of Bits (ENOB), Digitize Current

10uA

100uA

1mA

10mA

100mA

79. Specified with aperture Auto and open input terminals. For all ranges and for ≥1k sample rate, add an additional 3× RMS noise uncertainty to ppm of range.

80. Specified with aperture Auto, 100 Hz sine wave for sample rate ≤ 5 k, and 1 kHz sine wave for sample rate ≥ 10 k. Distortion is calculated using first five harmonics. For the 1 A, 3 A, and 10 A ranges,

use the 100 mA range accuracy; guaranteed by design.

81. Specified with aperture Auto, 100Hz sine wave for sample rate ≤5k, and 1kHz sine wave for sample rate ≥10k. For the 1A, 3A, and 10A ranges, use the 100mA ENOB; guaranteed by design.

82. Sample rate is not continuously adjustable. For valid discrete settings, see the Model DMM7510 Reference Manual.

DMM7510 7½-Digit Graphical Sampling Multimeter

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

True RMS AC Voltage and AC Current

Function Range 83 Resolution

1-Year Accuracy: ±(% of reading + % of range) TCAL ±5°C

3 Hz to 5 Hz 5 Hz to 10 Hz 10 Hz to 20 kHz 20 kHz to 50 kHz 50 kHz to 100 kHz 100 kHz to 300 kHz

Voltage 84

100.0000 mV 0.1 µV 1.0 + 0.03 0.30 + 0.03 0.06 + 0.03 0.14 + 0.05 0.6 + 0.08 4.0 + 0.5

1.000000 V 1 µV 1.0 + 0.03 0.30 + 0.03 0.06 + 0.03 0.14 + 0.05 0.6 + 0.08 4.0 + 0.5

10.00000 V 10 µV 1.0 + 0.03 0.30 + 0.03 0.06 + 0.03 0.14 + 0.05 0.6 + 0.08 4.0 + 0.5

100.0000 V 10 0 µV 1.0 + 0.03 0.30 + 0.03 0.06 + 0.03 0.14 + 0.05 0.6 + 0.08 4.0 + 0.5

700.000 V 1 mV 1.0 + 0.03 0.30 + 0.03 0.06 + 0.03 0.14 + 0.05 0.6 + 0.08 4.0 + 0.5

Temperature

Coefficient/°C

(all ranges)

– – 0.01 + 0.003 0.03 + 0.003 0.005 + 0.003 0.006 + 0.005 0.01 + 0.006 0.03 + 0.01

Function Range 83 Resolution

1-Year Accuracy: ±(% of reading + % of range) TCAL ± 5°C

3 Hz to 5 Hz 5 Hz to 10 Hz 10 Hz to 2 kHz 2 kHz to 5 kHz 5 kHz to 10 kHz

Current 84

1.000000 mA 1 nA 1.0 + 0.04 0.30 + 0.04 0.08 + 0.03 0.09 + 0.03 0.09 + 0.03

10.00000 mA 10 nA 1.0 + 0.04 0.30 + 0.04 0.08 + 0.03 0.09 + 0.03 0.09 + 0.03

100.0000 mA 100 nA 1.0 + 0.04 0.30 + 0.04 0.08 + 0.03 0.09 + 0.03 0.09 + 0.03

1.000000 A 1 µA 1.0 + 0.04 0.30 + 0.04 0.20 + 0.04 0.88 + 0.04 2.0 + 0.04

3.000000 A 1 µA 1.0 + 0.05 0.30 + 0.05 0.20 + 0.05 0. 88 + 0.05 2.0 + 0.05

10.00000 A 85 10 µA 1.0 + 0.05 0.40 + 0.05 0.40 + 0.05 0. 88 + 0.05 2.0 + 0.05

Temperature

Coefficient/°C

(all ranges)

– – 0.10 + 0.004 0.030 + 0.004 0.005 + 0.003 0.006 + 0.005 0.006 + 0.005

ADDITIONAL AC UNCERTAINTIES – LOW FREQUENCY UNCERTAINTY

Additional Uncertainty

±(% of reading), Lower

Frequency Uncertainty

Detector Bandwidth (BW)

3 BW

(3 Hz to 300 kHz)

30 BW

(30 Hz to 300 kHz)

300 BW

(300 Hz to 300 kHz)

20 Hz to 30 Hz 00.3 —

30 Hz to 50 Hz 0 0 —

50 Hz to 100 Hz 0 0 4.0

100 Hz to 200 Hz 0 0 0.72

200 Hz to 300 Hz 0 0 0.18

300 Hz to 500 Hz 0 0 0.07

> 500 Hz 0 0 0

ADDITIONAL AC VOLTAGE CREST FACTOR UNCERTAINTIES 86

ADDITIONAL UNCERTAINTY: ±(% of reading).

Input Signal

Frequency

Detector

Bandwidth

Maximum Crest Factor:

5 at Range Full Scale

1 to 2 2 to 3 3 to 4 4 to 5

3 Hz to 5 Hz 3 Hz 1.00 4.00 4.80 5.00

5 Hz to 10 Hz 3 Hz 0.50 1.20 1.30 1.40

10 Hz to 30 Hz 3 Hz 0.20 0.30 0.60 0.90

5 Hz to 100 Hz 30 Hz 0.20 0.30 0.60 0.90

100 Hz to 300 Hz 30 Hz 0.05 0.15 0.30 0.40

100 Hz to 300 Hz 300 Hz 0.50 1.20 1.30 1.50

500 Hz to 10 kHz 300 Hz 0.05 0.15 0.30 1.20

DMM7510 7½-Digit Graphical Sampling Multimeter

83. 20% overrange on AC functions except 1% on 700V, 3.33% on 3A, and 1% on 10A. Default

resolution is 6½ digits.

84. Specifications are for detector bandwidth of 3Hz and sine wave inputs >5% of range. Detector

bandwidth of 3Hz and 30Hz are multisample A/D conversions. Detector bandwidth of 300Hz

is a single A/D conversion, programmable from 0.0005 PLC to 15 PLC (60Hz), 12 PLC (50Hz).

Default condition set to 1 PLC.

85. Rear terminals only.

86. Applies for non-sine wave inputs, DC content ≤3% of range, maximum crest factor ≤5.0. For

bandwidth 30Hz, autozero off, 6½ digits at 1 PLC, 3½ digits at 0.0005 PLC.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

87. Rear input terminals only.

88. Specified for square wave inputs. Input signal must be >10% of ACV range. If input is<20mV

on the 100mV range, then the frequency must be >10Hz. For sine wave inputs, frequency

must be >100Hz. For frequencies ≤100Hz, threshold level ≤50% of input signal and ≤7Hz,

threshold level ≤3% of range.

89. Threshold range is voltage RMS and threshold level voltage peak. Specified with 1kHz square

wave. 100V and 700V threshold ranges guaranteed by design.

90. Reading speeds for autozero off, fixed range, autodelay off. Offset compensation off and open

lead detector off where applicable.

91. Buffer measurements: For <0.2 PLC, multisample, single buffer transfer binary reading only.

92. PC measurements: For 1 and 0.2 PLC single reading and single transfer to computer (USB).

93. Reading rates using factory default operating conditions and autorange off, autodelay off.

Speeds include measurement and data transfer out of the USB. ≥1000 readings with binary

transfer over USB.

94. For bandwidth 300Hz, autozero off, 6½ digits at 1 PLC, 3½ digits at 0.0005 PLC.

AC VOLTAGE CHARACTERISTICS

MEASUREMENT METHOD: AC-coupled, true RMS.

INPUT IMPEDANCE: 1MΩ ± 2%

<150pF.

VOLT*HERTZ PRODUCT: <2.1 × 107V*Hz verified; input frequency verified for <300kHz.

DMM7510 7½-Digit Graphical Sampling Multimeter

AC CURRENT CHARACTERISTICS

MEASUREMENT METHOD: AC-coupled, true RMS.

Range 1 mA 10 mA 100 mA 1 A 3 A 10 A 87

Burden Voltage (RMS) <16 mV <20 mV <0.2 V <0.4 V <1.3 V <0.65 V

Overload Recovery: For

each additional sustained

ampere beyond ±1.5A, add

the following initial % of

range error until thermally

settled after overload

recovery

0.006 0.006 0.12 0.05 — —

Frequency and Period

MEASUREMENT ACCURACY 88

Aperture

Measurement

Resolution

Accuracy

±(ppm of reading + ppm of aperture time)

Frequency: 3 Hz to 500 kHz

Period: 333 ms to 2 µs

1 Year, TCAL ±5°C 2 Year, TCAL ±5°C

250 ms 0.1 ppm 80 + 0.333 160 + 0.333

100 ms 0.1 ppm 80 + 3.33 160 + 3.33

10 ms 0.1 ppm 80 + 33.3 160 + 33.3

THRESHOLD LEVEL ACCURACY 89

Threshold Range

Threshold

Resolution

Accuracy ±(% of reading)

2 Year, TCAL ±5°C

100 mV to 700 V 0.05% 1.0%

FREQUENCY AND PERIOD CHARACTERISTICS

MEASUREMENT METHOD: Reciprocal counting technique.

APERTURE: 10ms to 273ms; default is 10ms.

TYPICAL READING RATES, 60Hz (50Hz) OPERATION 90, 91, 92, 93

Functions:

DC Voltage (10 V),

2-wire Ohms (≤10kΩ),

DC Current (1 mA)

Functions:

4-wire ohms (≤1 kΩ),

4-wire/3-wire RTD

Functions:

Thermistor

Functions:

Dry Circuit (≤1 kΩ)

NPLC Digits

Measurements

Into Buffer

Measurements

Into Computer

Measurements

Into Buffer

Measurements

Into Computer

Measurements

Into Buffer

Measurements

Into Computer

Measurements

Into Buffer

Measurements

Into Computer

17½ 59.8 (49.8) 58 (48) 29 (24) 28 (24) 57 (48) 57 (48) 27 (23) 26 (22)

0.2 6½ 295 (240) 250 (210) 128 (109) 119 (100) 230 (200) 230 (200) 100 (89) 96 (85)

0.06 5½ 965 (810) 950 (800) 310 (280) 315 (280) 900 (750) 900 (750) 190 (180) 190 (180)

0.006 4½ 7500 (6700) 7300 (6500) 750 (730) 740 (720) 6800 (6000) 6800 (6000) 295 (290) 295 (290)

0.0005 3½ 26000 (26000) 24000 (24000) 860 (860) 860 (860) 18000 (18000) 18000 (18000) 310 (310) 310 (310)

Functions: ACV, ACI

Detector Bandwidth

(Hz) Digits

Measurements

Into Buffer

Measurements

Into Computer

36½ 0.5 (0.5) 0.5 (0.5)

30 6½ 3.3 (3.3) 3.3 (3.3)

300 94 6½ 59.8 (49.8) 55 (46)

300 94 3½ 26200 (26200) 24500 (24500)

DIGITIZE, TYPICAL

Sampling Rate Digits Resolution

Measurements Into

Computer 93

10 kS/s 5½ 18 9700

20 kS/s 4½ 16 19000

50 kS/s 4½ 16 44400

100 kS/s 4½ 15 80000

1 MS/s 3½ 12 108000

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

A Greater Measure of Conﬁdence

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Tektronix Company

DMM7510 7½-Digit Graphical Sampling Multimeter

System Performance, Typical

MODE: 3½-digit, autozero off, 0.0005 PLC, excludes measurement time.

Time includes function change from DC voltage or 2-wire ohms to listed function.

Function Function Change (ms) Range Change (ms)

DC Voltage or 2-wire ohms (<10 kΩ) 6 1.3

4-wire ohms (<10 kΩ) 7 1.3

DC Current 71.3

Frequency or Period 95 71.3

AC Voltage or AC Current 71.3

Digitize Voltage or Current 71.3

RANGES FOR FUNCTION CHANGE TIMES

Function change times apply to the ranges listed in the table below.

Function Range

DC Voltage 10 V

2-wire or 4-wire Ohms 1 kΩ

DC Current 1 mA

Dry-circuit Ohms 10 Ω

Thermocouple Use DC Voltage rates

Thermistor Use 2-wire Ohms rates

AC Current 1 mA

AC Voltage 1 V

Buffer Transfer Speed (Binary)

Measurements into Computer

(per second)

USB LAN GPIB

Average for 1000 readings 280000 270000 190000

Average for 1000 readings with timestamp 170000 140000 100000

Triggering

TIME BASE ACCURACY: 25ppm.

TRIGGER SOURCE: Analog DCV, DCI, or any system trigger.

TRIGGER COUPLING: DC or AC (DCV function only).

INPUT TRIGGER LATENCY 96, 97, 98: <225ns.

INPUT TRIGGER JITTER 96, 97: <50ns.

SAMPLE PERIOD JITTER 96, 97: <1ns.

DMM REAR-PANEL TRIGGERS

EXT TRIG IN AND OUT: 0V to 5V logic signal input and output, TTL compatible.

EXT TRIGGER LATENCY (IN and OUT): <400ns.

EXT TRIGGER LATENCY (IN or OUT): <200ns (guaranteed by design).

ANALOG TRIGGERING 99

ANALOG LEVEL, EDGE, OR WINDOW TRIGGER TYPES 100

Trigger Characteristics Voltage Input Current Input

Input 100 mV to 1000 V 10 µA to 10 A

Resolution 0.05% 0.05%

Basic Accuracy (TACAL ±5°C) 101, 102 1% 1%

ANALOG TRIGGER LATENCIES

Digital I/O External

Positive Logic 800 ns + 40 ns jitter 930 ns + 40 ns jitter

Negative Logic 800 ns + 40 ns jitter 840 ns + 40 ns jitter

WINDOW FILTER AND MEMORY (BUFFER)

WINDOW FILTER SIZE: 0 to 10% of reading, where 0 averages all readings.

MEMORY: Up to 27.5 million timestamped readings with the compact buffer style, with additional

memory available using an external USB flash drive.

MAXIMUM INTERNAL MEMORY (Buffer): 27.5 million readings with the compact buffer style

(6½-digit without formatting), 11 million readings with the standard or full buffer style.

95. For DC voltage or 2-wire ohms to frequency or period, 10ms aperture. For AC current or AC

voltage, detector bandwidth is 300Hz.

96. Guaranteed by design; for digital I/O only.

97. Stimulus command required to meet specifications.

98. If using trigger model, add 200ns uncertainty.

99. For DC or AC coupled, the trigger level can be set up to 100% of measure range.

100. Rising or falling edge triggering supported. Window trigger requires setting two independent

levels.

101. Trigger event occurs after the threshold crossing at a time determined by total trigger

latencies.

102. Accuracy specifications require user ACAL and are verified with level trigger amplitude set to

50% of range with a 100Hz sine wave at 100% full scale of range. High frequency rejection

is off. NPLC 0.0005 (DC voltage/DC current) or aperture 1µs for digitize voltage or digitize

current. Specified for fixed range, autozero off. For digitized DC voltage AC coupled, add 0.5

%. For DC current and digitized DC current 3A or 10A ranges, add an additional 2%.

Model DMM7510 condensed specifications

DIGITAL MULTIMETERS & SYSTEMS

www.keithley.com

1.888.KEITHLEY (U.S. only)

A Greater Measure of Conﬁdence A Tektronix Company

GENERAL INSTRUMENT SPECIFICATIONS

SPECIFICATION CONDITIONS: This document contains

specifications and supplemental information for the Model

DMM7510 Precision Sampling Digital Multimeter instru-

ment. Specifications are the standards against which the

Model DMM7510 is tested. Upon leaving the factory, the

Model DMM7510 meets these specifications. Supplemental,

typical, and characteristic values are non-warranted, apply

at 23°C, and are provided solely as useful information. All

specifications apply to front or rear terminal inputs, except

10 A specifications (rear terminals only).

INPUT PROTECTION: 1010 V DC (715 VRMS V AC) all ranges

and functions on HI and LO terminals; 350V all ranges and

functions on sense HI, sense LO terminals; 250V rated cur-

rent input terminal; fused 3A and 10A ranges; current input

terminals protected to 1kV.

3A INPUT FUSE PROTECTION: 3.5A, 1kV fast blow type;

Keithley part number DMM7510-FUSE-3A.

10A INPUT FUSE PROTECTION: 11A, 1kV fast blow type;

Keithley part number DMM7510-FUSE-10A.

AC VOLTAGE INPUT: Maximum DCV: 1000V on any AC

voltage range.

COMMON MODE ISOLATION: 500VDC or ACVpeak LO to

chassis. All terminals >10GΩ, <350pF any terminal to

chassis.

POWER LINE: Universal input, 100V to 240V.

LINE FREQUENCY: 50Hz or 60Hz, automatically sensed at

power-up.

POWER CONSUMPTION: 60VA.

OPERATING ENVIRONMENT: Specified for 0° to 50°C, ≤80%

relative humidity at 35°C, altitude up to 2000 meters.

STORAGE ENVIRONMENT: –30° to 70°C.

REAL TIME CLOCK: Lithium battery backup (3+ years

battery life).

EMC: Conforms to European Union EMC Directive.

SAFETY: NRTL listed to UL61010-1, and CSA C22.2 No 61010-1;

conforms with European Union Low Voltage Directive.

VIBRATION: MIL-PRF-28800F Class 3, Random.

WARM-UP: 90 minutes to rated accuracy.

INPUT SIGNAL CONNECTIONS: Front and rear safety banana

jacks.

COOLING: Forced air, fixed speed.

DIMENSIONS:

Without handle and bumpers: 88mm high × 213mm wide

× 410mm deep (3.46 in. × 8.39 in. × 16.13 in.).

With handle and bumpers (bench configuration):

106mm high × 255mm wide × 425mm deep (4.18 in. ×

10.05 in. × 16.75 in.).

SHIPPING WEIGHT (with bumpers and handle): 4.08kg

(9.0 lb.).

SHIPPING WEIGHT (without bumpers and handle): 3.63kg

(8.0 lb.).

DIGITAL I/O:

Connector: 9-pin female D.

5V Power Supply Pin: Limited to 500 mA at > 4 V (solid-

state fuse protected).

Lines: Six input/output, user-defined, for digital I/O or

triggering.

Input Signal Levels: 0.7V (maximum logic low)

3.7V (minimum logic high).

Input Voltage Limits: –0.25V (absolute minimum)

+5.25V (absolute maximum).

Maximum Source Current: +2.0mA at >2.7V (per pin).

Maximum Sink Current: –50mA at 0.7V (per pin, sol-

id-state fuse protected).

Handler: User-defined start of test, end of test, four cate-

gory bits

MATH FUNCTIONS: Rel, dB, Limit Test, Percentage, 1/x, and

mX + b.

REMOTE INTERFACE:

LAN: RJ-45 connector, 10/100BT; Virtual Front Panel.

IP Configuration: Static or DHCP.

GPIB: IEEE-488.1 compliant. Supports IEEE-488.2 common

commands and status model topology.

USB Device (rear panel, type B): 2.0 full speed, USBTMC

compliant.

USB Host (front panel, type A): USB 2.0, support for flash

drives, FAT 32.

LXI COMPLIANCE: LXI version 1.4 Core 2011.

LANGUAGE: Embedded Test Script Processor (TSP) accessible

from any host interface; responds to high-speed test scripts

comprised of remote commands and statements (for exam-

ple, branching, looping, math); able to execute high-speed

test scripts stored in memory without host intervention;

also SCPI (default command set).

ACCESSORIES SUPPLIED: Product Information CD-ROM,

Model DMM7510 Quick Start Guide, Kickstart Software

Quick Start Guide, power cord, 1 m USB cable (type A to

type B), 3 m LAN cable, and Model 1756 Standard Test

Lead Kit.

ACCESSORIES AVAILABLE: (Calibration / Data / ISO 17025),

software IVI/VISA drivers for Microsoft® Visual Basic®,

Visual C/C++®, National Instruments (NI™) LabVIEW™,

Keithley Test Script Builder, Keithley KickStart, and NI

LabWindows™/CVI.

DISPLAY: Five-inch capacitive touch, color thin-film-transistor

(TFT) WVGA (800×480) with LED backlight.

PASSWORD PROTECTION: 30 characters.

EXPANSION INTERFACE: The TSP-Link® expansion interface

allows TSP-enabled instruments to trigger and communi-

cate with each other.

IP CONFIGURATION: Static or DHCP (manual or automatic).

DMM7510 7½-Digit Graphical Sampling Multimeter

Model DMM7510 condensed specifications