SN54LV574, SN74LV574 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCLS199B - MARCH 1993 - REVISED APRIL 1996 D D D D SN54LV574 . . . J OR W PACKAGE SN74LV574 . . . DB, DW, OR PW PACKAGE (TOP VIEW) OE 1D 2D 3D 4D 5D 6D 7D 8D GND 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q CLK 3D 4D 5D 6D 7D 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2Q 3Q 4Q 5Q 6Q 8D GND CLK 8Q 7Q The 'LV574 feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. This device is particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. 20 2 SN54LV574 . . . FK PACKAGE (TOP VIEW) description These octal edge-triggered D-type flip-flops are designed for 2.7-V to 5.5-V VCC operation. 1 OE VCC 1Q D EPIC (Enhanced-Performance Implanted CMOS) 2- Process Typical VOLP (Output Ground Bounce) < 0.8 V at VCC, TA = 25C Typical VOHV (Output VOH Undershoot) > 2 V at VCC, TA = 25C ESD Protection Exceeds 2000 V Per MIL-STD-883C, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Latch-Up Performance Exceeds 250 mA Per JEDEC Standard JESD-17 Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), Thin Shrink Small-Outline (PW), Ceramic Flat (W) Packages, Chip Carriers (FK), and (J) 300-mil DIPs 2D 1D D On the positive transition of the clock (CLK) input, the Q outputs are set to the logic levels set up at the data (D) inputs. A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. OE does not affect the internal operations of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The SN74LV574 is available in TI's shrink small-outline package (DB), which provides the same I/O pin count and functionality of standard small-outline packages in less than half the printed-circuit-board area. The SN54LV574 is characterized for operation over the full military temperature range of -55C to 125C. The SN74LV574 is characterized for operation from -40C to 85C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC is a trademark of Texas Instruments Incorporated. Copyright 1996, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54LV574, SN74LV574 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCLS199B - MARCH 1993 - REVISED APRIL 1996 FUNCTION TABLE (each flip-flop) INPUTS OE CLK D OUTPUT Q L H H L L L L H or L X Q0 H X X Z logic symbol OE CLK 1D 2D 3D 4D 5D 6D 7D 8D 1 11 2 logic diagram (positive logic) EN OE C1 1D 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 CLK 1 11 1Q C1 2Q 3Q 1D 2 19 1Q 1D 4Q 5Q 6Q To Seven Other Channels 7Q 8Q This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for DB, DW, J, PW, and W packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to VCC + 0.5 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 mA Maximum power dissipation at TA = 55C (in still air) (see Note 3): DB package . . . . . . . . . . . . . . . . . . . 0.6 W DW package . . . . . . . . . . . . . . . . . . 1.6 W PW package . . . . . . . . . . . . . . . . . . . 0.7 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. This value is limited to 7 V maximum. 3. The maximum package power dissipation is calculated using a junction temperature of 150C and a board trace length of 750 mils. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54LV574, SN74LV574 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCLS199B - MARCH 1993 - REVISED APRIL 1996 recommended operating conditions (see Note 4) SN54LV574 VCC Supply voltage MAX MIN MAX 2.7 5.5 2.7 5.5 VIH High level input voltage High-level VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V VIL Low level input voltage Low-level VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V VI VO Input voltage 0 Output voltage 0 IOH High level output current High-level VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V IOL Low level output current Low-level VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V t /v Input transition rise or fall rate TA Operating free-air temperature NOTE 4: Unused inputs must be held high or low to prevent them from floating. SN74LV574 MIN 2 2 3.15 3.15 0.8 0.8 1.65 0 0 V V 1.65 VCC VCC UNIT VCC VCC -8 -8 -16 -16 8 8 16 16 V V V mA mA 0 100 0 100 ns / V - 55 125 - 40 85 C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH TEST CONDITIONS IOH = - 100 A IOH = - 8 mA MIN to MAX IOH = - 16 mA IOL = 100 A VOL VCC SN54LV574 MIN TYP II VI = VCC or GND IOZ VO = VCC or GND ICC VI = VCC or GND, GND nICC One input at VCC - 0.6 V, Other inputs at VCC or GND Ci VI = VCC or GND Co VO = VCC or GND IO = 0 MIN TYP 3V VCC - 0.2 2.4 VCC - 0.2 2.4 4.5 3.6 3.6 MIN to MAX IOL = 8 mA IOL = 16 mA SN74LV574 MAX MAX UNIT V 0.2 0.2 3V 0.4 0.4 4.5 V 0.55 0.55 3.6 V 1 1 5.5 V 1 1 3.6 V 5 5 5.5 V 5 5 3.6 V 20 20 5.5 V 20 20 3 V to 3.6 V 500 500 3.3 V 2.5 2.5 5V 3 3 3.3 V 7 7 5V 10 10 V A A A A pF pF F For conditions shown as MIN or MAX, use the appropriate values under recommended operating conditions. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54LV574, SN74LV574 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCLS199B - MARCH 1993 - REVISED APRIL 1996 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) SN54LV574 VCC = 5 V 0.5 V MIN fclock tw Clock frequency tsu Setup time before CLK th Hold time, data after CLK MAX VCC = 3.3 V 0.3 V MIN 50 Pulse duration, CLK high or low High or low MAX VCC = 2.7 V MIN 40 UNIT MAX 30 MHz 8 12 14 ns 5 8 9 ns 4 3 3 ns timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) SN74LV574 VCC = 5 V 0.5 V MIN fclock tw Clock frequency MAX VCC = 3.3 V 0.3 V MIN 50 Pulse duration, CLK high or low tsu Setup time before CLK th Hold time, data after CLK High or low MAX VCC = 2.7 V MIN 40 UNIT MAX 30 MHz 8 12 14 ns 5 8 9 ns 4 3 3 ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LV574 PARAMETER FROM (INPUT) TO (OUTPUT) fmax VCC = 5 V 0.5 V MIN TYP MAX 50 tpd CLK ten tdis 70 VCC = 3.3 V 0.3 V MIN TYP MAX 40 50 VCC = 2.7 V MIN MAX 30 UNIT MHz Q 12 17 17 24 26 ns OE Q 11 17 16 22 25 ns OE Q 14 19 18 27 28 ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN74LV574 PARAMETER FROM (INPUT) TO (OUTPUT) fmax VCC = 5 V 0.5 V MIN TYP MAX 50 70 40 50 VCC = 2.7 V MIN MAX 30 UNIT MHz tpd CLK Q 12 17 17 24 26 ns ten OE Q 11 17 16 22 25 ns tdis OE Q 14 19 18 27 28 ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 VCC = 3.3 V 0.3 V MIN TYP MAX POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54LV574, SN74LV574 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCLS199B - MARCH 1993 - REVISED APRIL 1996 operating characteristics, TA = 25C PARAMETER TEST CONDITIONS VCC Outputs enabled Cpd Outputs enabled 33V 3.3 CL = 50 pF F, Outputs disabled POST OFFICE BOX 655303 UNIT 40 Outputs disabled Power dissi dissipation ation capacitance ca acitance per er fli flip-flop -flo TYP * DALLAS, TEXAS 75265 22 f = 10 MHz pF F 5V 44 24 5 SN54LV574, SN74LV574 OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCLS199B - MARCH 1993 - REVISED APRIL 1996 PARAMETER MEASUREMENT INFORMATION S1 1 k From Output Under Test Vz Open GND CL = 50 pF (see Note A) TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open Vz GND 1 k WAVEFORM CONDITION Vm Vi Vz LOAD CIRCUIT VCC = 4.5 V to 5.5 V 0.5 x VCC VCC 2 x VCC VCC = 2.7 V to 3.6 V 1.5 V 2.7 V 6V Vi Vm Timing Input 0V tw tsu Vi Input Vm th Vi Vm Vm Data Input Vm 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES Vi Vm Input 0V VOH Vm Output Vm VOL Output VOH Vm 0V Vm VOL tPLZ Output Waveform 1 S1 at Vz (see Note B) tPLH tPHL Vm Vm tPZL tPHL tPLH Vi Output Control Vm Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Vm tPZH 0.5 x Vz VOL + 0.3 V VOL tPHZ Vm VOH - 0.3 V VOH [0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated