SMT inductors SIMID series, SIMID 1210-100 Series/Type: B82422A*100 Date: June 2009 %BUB4IFFU (c) EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. SMT inductors, SIMID series B82422A*100 SIMID 1210-100 Size 1210 (EIA) or 3225 (IEC) Rated inductance 0.0082 NH to 100 NH Rated current 65 mA to 800 mA Construction Ceramic or ferrite core Laser-welded winding Flame-retardant molding Features Temperature range up to 145 C High Q factor High resonance frequency Qualified to AEC-Q200 Suitable for lead-free reflow soldering as referenced in JEDEC J-STD 020C RoHS-compatible Applications Filtering of supply voltages, coupling, decoupling Antenna systems Automotive electronics Telecommunications Consumer and data processing equipment Industrial electronics Terminals Base material CuSn6 Layer composition Cu, Ag, Sn (lead-free)1) Electro-plated Marking Marking on component: Manufacturer, L value (in nH), tolerance of L value (coded), date of manufacture (YWWD) Minimum data on reel: Manufacturer, ordering code, L value, quantity, date of packing Delivery mode and packing units 8-mm blister tape, wound on 180-mm or 330-mm reel Packing units: 180-mm reel: 2000 pcs./reel 330-mm reel: 8000 pcs./reel 1) Ni-barrier-plated terminals on request (B82422A*150). Please read Cautions and warnings and Important notes at the end of this document. 2 06/09 SMT inductors, SIMID series B82422A*100 SIMID 1210-100 Dimensional drawing and layout recommendation 20.11) A 0.50.2 1) B C D B IND0053-6 20.1 0.4 min.1) 3.2+0.3 2.5+0.3 0.15 max. A B C D 2.7 1.15 2.1 4.4 Marking 1) Soldering area Dimensions in mm IND0073-6-E Taping and packing Reel <_ 2.6 40.1 _0 12.75 +0.15 _2 330 +0 80.3 20.05 _2 180 +0 1.5+0.1 <_ 4.2 Component 14.4 max. 3.50.05 40.1 1.750.1 Blister tape _0 8.4 +1.5 1.0+0.2 621.5 IND0592-V Direction of unreeling IND0559-Z-E Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. 3 06/09 SMT inductors, SIMID series B82422A*100 SIMID 1210-100 Technical data and measuring conditions Rated inductance LR Measured with impedance analyzer Agilent 4294A at frequency fL, 0.1 V, 20 C Q factor Qmin Measured with impedance analyzer Agilent 4294A at frequency fQ, 20 C Rated temperature TR 125 C Rated current IR Maximum permissible DC with inductance decrease L/L0 10% and temperature increase of 20 K at rated temperature Self-resonance frequency fres,min Measured with network analyzer Agilent 8753D, 20 C DC resistance Rmax Measured at 20 C Solderability (lead-free) Sn95.5Ag3.8Cu0.7: (245 5) C, (5 0.3) s Wetting of soldering area 90% (based on IEC 60068-2-58) Resistance to soldering heat 260 C, 40 s (as referenced in JEDEC J-STD 020C) Climatic category 55/125/56 (to IEC 60068-1) Storage conditions Mounted: -55 C ... +125 C Packaged: -25 C ... +40 C, 75% RH Weight Approx. 50 mg Please read Cautions and warnings and Important notes at the end of this document. 4 06/09 SMT inductors, SIMID series B82422A*100 SIMID 1210-100 Characteristics and ordering codes LR Tolerance H fL Qmin MHz fQ IR Rmax MHz mA fres, min Ordering code 1)2) ( 180-mm reel) MHz Core material: ceramic 0.0082 5% 0.010 10% 10 20 100 800 0.08 4000 B82422A3829+100 10 20 100 750 0.09 4000 B82422A3100+100 0.012 10 25 100 700 0.10 3500 B82422A3120+100 0.015 10 27 100 640 0.12 3000 B82422A3150+100 0.018 10 30 100 640 0.12 2500 B82422A3180+100 0.022 10 30 100 600 0.14 2500 B82422A3220+100 0.027 10 23 50 600 0.14 1850 B82422A3270+100 0.033 10 20 50 540 0.17 1700 B82422A3330+100 0.039 10 25 50 530 0.18 1450 B82422A3390+100 0.047 10 26 50 510 0.19 1350 B82422A3470+100 0.056 10 26 50 500 0.20 1200 B82422A3560+100 0.068 10 27 50 480 0.21 1150 B82422A3680+100 0.082 10 27 50 450 0.24 1050 B82422A3820+100 0.10 10 25 50 440 0.26 1000 B82422A3101+100 0.12 1 22 30 400 0.32 880 B82422A3121+100 0.15 1 25 30 390 0.33 850 B82422A3151+100 0.18 1 25 30 360 0.38 800 B82422A3181+100 0.22 1 25 30 280 0.64 700 B82422A3221+100 0.27 1 20 30 235 0.90 650 B82422A3271+100 0.33 1 22 30 200 1.3 580 B82422A3331+100 0.39 1 22 30 190 1.4 540 B82422A3391+100 0.47 1 22 30 150 2.2 480 B82422A3471+100 0.56 1 22 30 150 2.2 400 B82422A3561+100 0.68 1 22 30 145 2.4 280 B82422A3681+100 0.82 1 22 30 140 2.5 240 B82422A3821+100 ^ J ^ K Closer tolerances and special versions on request. Higher currents possible at temperatures <TR on request. Sample kit available. Ordering code: B82422X100 For more information refer to chapter "Sample kits". 1) Replace the + by the code letter for the required inductance tolerance. For reel size 330 mm the last digit has to be an 8. Example: B82422A3829K108 2) For Ni-barrier-plated terminals replace the last three digits "100" by "150" (reel 180 mm) or "158" (reel 330 mm). Please read Cautions and warnings and Important notes at the end of this document. 5 06/09 SMT inductors, SIMID series B82422A*100 SIMID 1210-100 Characteristics and ordering codes LR Tolerance H fL Qmin MHz fQ IR Rmax MHz mA fres, min Ordering code 1)2) ( 180-mm reel) MHz Core material: ferrite 1.0 5% 1.2 10% 1 20 7.96 380 0.34 320 B82422A1102+100 1 20 7.96 370 0.37 300 B82422A1122+100 1.5 1 20 7.96 340 0.50 270 B82422A1152+100 1.8 1 25 7.96 290 0.60 250 B82422A1182+100 2.2 1 25 7.96 270 0.75 125 B82422A1222+100 2.7 1 25 7.96 240 0.88 110 B82422A1272+100 3.3 1 27 7.96 200 1.20 110 B82422A1332+100 3.9 1 27 7.96 190 1.40 110 B82422A1392+100 4.7 1 27 7.96 150 2.20 110 B82422A1472+100 5.6 1 27 7.96 140 2.60 100 B82422A1562+100 6.8 1 27 7.96 135 2.80 90 B82422A1682+100 8.2 1 27 7.96 130 3.00 90 B82422A1822+100 10 1 27 2.52 180 1.60 25 B82422A1103+100 12 0.1 27 2.52 175 1.65 23 B82422A1123+100 15 0.1 27 2.52 165 1.85 20 B82422A1153+100 18 0.1 27 2.52 155 2.00 17 B82422A1183+100 22 0.1 27 2.52 140 2.65 16 B82422A1223+100 27 0.1 27 2.52 120 3.70 15 B82422A1273+100 33 0.1 27 2.52 105 4.50 13 B82422A1333+100 39 0.1 27 2.52 90 6.30 12 B82422A1393+100 47 0.1 27 2.52 85 7.00 11 B82422A1473+100 56 0.1 27 2.52 85 6.75 9 B82422A1563+100 68 0.1 27 2.52 80 7.70 9 B82422A1683+100 82 0.1 27 2.52 70 10.0 8 B82422A1823+100 100 0.1 27 2.52 65 11.5 7 B82422A1104+100 ^ J ^ K Closer tolerances and special versions on request. Higher currents possible at temperatures <TR on request. Sample kit available. Ordering code: B82422X100 For more information refer to chapter "Sample kits". 1) Replace the + by the code letter for the required inductance tolerance. For reel size 330 mm the last digit has to be an 8. Example: B82422A1104K108 2) For Ni-barrier-plated terminals replace the last three digits "100" by "150" (reel 180 mm) or "158" (reel 330 mm). Please read Cautions and warnings and Important notes at the end of this document. 6 06/09 SMT inductors, SIMID series B82422A*100 SIMID 1210-100 Impedance |Z| versus frequency f measured with impedance analyzer Agilent 4291A, typical values at 20 C Inductance L versus DC load current IDC measured with LCR meter Agilent 4275A, typical values at 20 C Q factor versus frequency f measured with impedance analyzer Agilent 4194A/4291A, typical values at 20 C Current derating Iop/IR versus ambient temperature TA (rated temperature TR = 125 C) 7 06/09 Cautions and warnings Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. - Particular attention should be paid to the derating curves given there. - The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. The following points must be observed if the components are potted in customer applications: - Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. - It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. - The effect of the potting material can change the high-frequency behaviour of the components. Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document. 8 06/09 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 9 06/09