a FEATURES Single 8-Bit DAC 20-Pin SOIC/TSSOP Package +2.7 V to +5.5 V Operation Internal and External Reference Capability DAC Power-Down Function Parallel Interface On-Chip Output Buffer Rail-to-Rail Operation Low Power Operation 1.75 mA max @ 3.3 V Power-Down to 1 mA max @ 258C APPLICATIONS Portable Battery Powered Instruments Digital Gain and Offset Adjustment Programmable Voltage and Current Sources Programmable Attenuators +2.7 V to +5.5 V, Parallel Input, Voltage Output 8-Bit DAC AD7801 FUNCTIONAL BLOCK DIAGRAM D7 D0 WR CS INPUT REGISTER DAC REGISTER CONTROL LOGIC I DAC I/V MUX POWER-ON RESET /2 AD7801 PD CLR LDAC REFIN VDD VOUT AGND DGND GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD7801 is a single, 8-bit, voltage out DAC that operates from a single +2.7 V to +5.5 V supply. Its on-chip precision output buffer allows the DAC output to swing rail to rail. The AD7801 has a parallel microprocessor and DSP compatible interface with high speed registers and double buffered interface logic. Data is loaded to the input register on the rising edge of CS or WR. 1. Low Power, Single Supply operation. This part operates from a single +2.7 V to +5.5 V supply and consumes typically 5 mW at 3 V, making it ideal for battery powered applications. Reference selection for the AD7801 can be either an internal reference derived from the VDD or an external reference applied at the REFIN pin. The output of the DAC can be cleared by using the asynchronous CLR input. The low power consumption of this part makes it ideally suited to portable battery operated equipment. The power consumption is less than 5 mW at 3.3 V, reducing to less than 3 W in power-down mode. 2. The on-chip output buffer amplifier allows the output of the DAC to swing rail to rail with a settling time of typically 1.2 s. 3. Internal or external reference capability. 4. High speed parallel interface. 5. Power-down capability. When powered down the DAC consumes less than 1 A at 25C. 6. Packaged in 20-lead SOIC and TSSOP packages. The AD7801 is available in a 20-lead SOIC and a 20-lead TSSOP package. REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 617/329-4700 World Wide Web Site: http://www.analog.com Fax: 617/326-8703 (c) Analog Devices, Inc., 1997 (VDD = +2.7 V to +5.5 V, Internal Reference; CL = 100 pF, RL = 10 kV to VDD and GND. All specifications TMIN to TMAX unless otherwise noted.) AD7801-SPECIFICATIONS Parameter B Versions1 Units Conditions/Comments STATIC PERFORMANCE Resolution Relative Accuracy2 Differential Nonlinearity Zero-Code Error @ +25C Full-Scale Error Zero-Code Error Drift Gain Error3 8 1 1 3 -0.75 100 1 Bits LSB max LSB max LSB typ LSB typ V/C typ % FSR typ Guaranteed Monotonic All Zeros Loaded to DAC Register All Ones Loaded to DAC Register DAC REFERENCE INPUT REFIN Input Range REFIN Input Impedance 1 to VDD/2 10 V min/V max M typ OUTPUT CHARACTERISTICS Output Voltage Range Output Voltage Settling Time Slew Rate Digital-to-Analog Glitch Impulse Digital Feedthrough DC Output Impedance Short Circuit Current Power Supply Rejection Ratio4 0 to VDD 2 7.5 1 0.2 40 14 0.0003 V min/V max s max V/s typ nV-s typ nV-s typ typ mA typ %/% max LOGIC INPUTS Input Current VINL, Input Low Voltage VINL, Input Low Voltage VINH, Input High Voltage VINH, Input High Voltage Pin Capacitance 10 0.8 0.6 2.4 2.1 7 A max V max V max V min V min pF max 2.7/5.5 V min/V max POWER REQUIREMENTS VDD IDD (Normal Mode) VDD = 3.3 V @ 25C TMIN to TMAX VDD = 5.5 V @ 25C TMIN to TMAX IDD (Power-Down) @ 25C TMIN to TMAX 1.55 1.75 mA max mA max 2.35 2.5 mA max mA max 1 2 A max A max Typically 1.2 s 1 LSB Change Around Major Carry VDD = 10% VDD = +5 V VDD = +3 V VDD = +5 V VDD = +3 V DAC Active and Excluding Load Current VIH = VDD and VIL = GND See Figure 6 VIH = VDD and VIL = GND See Figure 18 NOTES 1 Temperature ranges are as follows: B Version: -40C to +105C 2 Relative Accuracy is calculated using a reduced code range of 15 to 245. 3 Gain Error is specified between Codes 15 and 245. The actual error at Code 15 is typically 3 LSB. 4 Guaranteed by characterization at product release, not production tested. Specifications subject to change without notice. t1 t2 CS t3 WR t4 t5 D7-D0 t6 t7 LDAC t8 CLR Figure 1. Timing Diagram for Parallel Data Write -2- REV. 0 AD7801 TIMING CHARACTERISTICS1, 2 (VDD = +2.7 V to +5.5 V; GND = 0 V; Internal V DD/2 Reference. All specifications TMIN to TMAX unless otherwise noted.) Parameter Limit at TMIN, TMAX (B Version) Units Conditions/Comments t1 t2 t3 t4 t5 t6 t7 t8 0 0 20 15 4.5 20 20 20 ns min ns min ns min ns min ns min ns min ns min ns min Chip Select to Write Setup Time Chip Select to Write Hold Time Write Pulse Width Data Setup Time Data Hold Time Write to LDAC Setup Time LDAC Pulse Width CLR Pulse Width NOTES 1 Sample tested at +25C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of V DD) and timed from a voltage level of (VIL + VIH)/2. tr and tf should not exceed 1 s on any digital input. 2 See Figure 1. ORDERING GUIDE ABSOLUTE MAXIMUM RATINGS* (TA = +25C unless otherwise noted) VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V Reference Input Voltage to AGND . . . . -0.3 V to VDD + 0.3 V Digital Input Voltage to DGND . . . . . . -0.3 V to VDD + 0.3 V AGND to DGND . . . . . . . . . . . . . . . . . . . . . -0.3 V to +0.3 V VOUT to AGND . . . . . . . . . . . . . . . . . . -0.3 V to VDD + 0.3 V Operating Temperature Range Commercial (B Version) . . . . . . . . . . . . . -40C to +105C Storage Temperature Range . . . . . . . . . . . . -65C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150C SSOP Package, Power Dissipation . . . . . . . . . . . . . . . 700 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 143C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . +215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220C SOIC Package, Power Dissipation . . . . . . . . . . . . . . . 870 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 74C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . +215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220C Model Temperature Range Package Option* AD7801BR AD7801BRU -40C to +105C -40C to +105C R-20 RU-20 *R = Small Outline; RU = Thin Shrink Small Outline. *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD7801 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. 0 -3- WARNING! ESD SENSITIVE DEVICE AD7801 PIN CONFIGURATION 20 DGND (MSB) DB7 1 DB6 2 19 VOUT DB5 3 18 NC 17 AGND DB4 4 DB3 5 AD7801 16 REFIN TOP VIEW 15 V DD (Not to Scale) 14 CLR DB1 7 DB2 6 13 LDAC (LSB) DB0 8 CS 9 12 PD WR 10 11 DGND NC = NO CONNECT PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1-8 9 10 11 12 13 D7-D0 CS WR DGND PD LDAC 14 CLR 15 16 VDD REFIN 17 18 19 20 AGND NC VOUT DGND Parallel Data Inputs. 8-bit data is loaded to the input register of the AD7801 under the control of CS and WR. Chip Select. Active low logic input. Write Input. WR is an active low logic input used in conjunction with CS to write data to the input register. Digital Ground Active low input used to put the part into low power mode reducing current consumption to less than 1 A. Load DAC Logic Input. When this logic input is taken low the DAC output is updated with the contents of its DAC register. If LDAC is permanently tied low the DAC is updated on the rising edge of WR. Asynchronous Clear Input (Active Low). When this input is taken low the DAC register is loaded with all zeroes and the DAC output is cleared to zero volts. Power Supply Input. This part can be operated from +2.7 V to +5.5 V and should be decoupled to GND. External Reference Input. This can be used as the reference for the DAC. The range on this reference input is 1 V to VDD/2. If REFIN is tied directly to VDD the internal VDD/2 reference is selected. Analog Ground reference point and return point for all analog current on the part. No Connect Pin. Analog Output Voltage from the DAC. The output amplifier can swing rail to rail on its output. Digital Ground reference point and return point for all digital current on the part. -4- REV. 0 Typical Performance Characteristics- AD7801 5 3.5 4.92 3.25 800 640 480 VOUT - Volts VOUT - mV 560 VDD = 5V AND 3V INTERNAL REFERENCE TA = +25 C DAC LOADED WITH 00HEX 400 320 240 4.84 3.0 4.76 2.75 4.68 4.6 4.52 4.36 80 4.28 4.2 8 2 4 6 SINK CURRENT - mA Figure 2. Output Sink Current Capability with VDD = 3 V and VDD = 5 V VDD = 5V INTERNAL REFERENCE DAC REGISTER LOADED WITH FFHEX TA = +25C 4.44 160 0 0 0 2.0 1.25 1.0 8 0.4 2 3 4 5 6 SOURCE CURRENT - mA 7 8 DAC ACTIVE INTERNAL REFERENCE TA = +25C 3.0 3.0 LOGIC INPUTS = VIH OR VIL INL ERROR 0.25 0.2 VDD = 5.5V 2.0 1.5 0.15 2.0 LOGIC INPUTS = VDD OR GND VDD = 3.3V 1.0 DNL ERROR IDD - mA 2.5 IDD - mA ERROR - LSBs 1 4.0 0.35 0.3 0 Figure 4. Output Source Current Capability with VDD = 3 V INTERNAL REFERENCE LOGIC INPUTS = VDD OR GND DAC ACTIVE 3.5 VDD = 3V INTERNAL REFERENCE DAC REGISTER LOADED WITH FFHex TA = +25C 1.5 2 4 6 SOURCE CURRENT - mA 4.0 VDD = 5V TA = +25 C 2.5 2.25 1.75 Figure 3. Output Source Current Capability with VDD = 5 V 0.5 0.45 VOUT - Volts 720 1.0 0.1 0.5 0.05 0 -50 0 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 REFERENCE VOLTAGE - Volts Figure 5. Relative Accuracy vs. External Reference -25 0 25 50 75 TEMPERATURE - C 100 0 2.5 125 Figure 6. Typical Supply Current vs. Temperature 3.0 3.5 4.0 4.5 VDD - Volts 5.0 5.5 Figure 7. Typical Supply Current vs. Supply Voltage 10 5 WR ATTENUATION - dB 0 T 1 -5 PD 2 -10 2 -15 VOUT VOUT -20 -25 VDD = 5V EXTERNAL SINEWAVE REFERENCE DAC REGISTER LOADED WITH FFHEX TA = +25C -30 -35 -40 1 10 100 1k FREQUENCY - Hz Figure 8. Large Scale Signal Frequency Response REV. 0 3 10k VDD = 3V INTERNAL VOLTAGE REFERENCE FULL SCALE CODE CHANGE 00H-FFH TA = +25C CH1 5V, CH2 1V, CH3 20mV TIME BASE = 200 ns/Div Figure 9. Full-Scale Settling Time -5- 1 VOUT AD7801 POWER-UP TIME VDD = 5V INTERNAL REFERENCE DAC IN POWER-DOWN INITIALLY CH1 = 2V/div, CH2 = 5V/Div, TIME BASE = 2 s/Div Figure 10. Exiting Power-Down (Full Power-Down) AD7801-Typical Performance Characteristics 10 9 T 8 ZERO CODE ERROR - LSB VDD 1 T 2 VOUT 7 6 5 5.00V CH2 VOUT 4 3 2 0 -50 5.00V M20.0ms CH1 VDD = 5V INTERNAL VOLTAGE REFERENCE 10 LSB STEP CHANGE TA = +258C VDD = 2.7 TO 5.5V DAC LOADED WITH ALL ZEROES INTERNAL REFERENCE 2 1 CH1 WR 1 -25 0 25 50 75 100 CH1 5.00V, CH2 50.0mV, M 250ns 125 TEMPERATURE - C Figure 11. Power-On--Reset Figure 12. Zero Code Error vs. Temperature 0.5 VDD = 5V INTERNAL REFERENCE 5k 100pF LOAD LIMITED CODE RANGE (15-245) TA = +25C 0.5 0.4 0.4 0.3 0.1 0 -0.1 -0.2 0.2 0.1 0.3 DNL ERROR - LSB 0.2 0.5 VDD = 5V INTERNAL REFERENCE 0 -0.1 -0.2 0.2 0.1 0 -0.2 -0.3 -0.3 -0.4 -0.4 -0.4 -0.5 -0.5 -60 -40 -20 0 32 64 96 128 160 192 224 256 INPUT CODE (15 to 245) Figure 14. Integral Linearity Plot 0 20 40 60 80 100 120 140 TEMPERATURE - C Figure 15. Typical INL vs. Temperature 0 20 40 60 80 100 120 140 TEMPERATURE - C Figure 16. Typical DNL vs. Temperature VDD = 5V LOGIC INPUTS = VDD OR GND 900 VDD = 5V % -0.5 -60 -40 -20 1000 1.0 0.8 INT REFERENCE ERROR - VDD = 5V INTERNAL REFERENCE -0.1 -0.3 POWER DOWN CURRENT - nA INL ERROR - LSB 0.3 INL ERROR - LSB 0.4 Figure 13. Small-Scale Settling Time 0.6 0.4 0.2 800 700 600 500 400 300 200 100 0 -60 -40 -20 0 -50 0 20 40 60 80 100 120 140 TEMPERATURE - C Figure 17. Typical Internal Reference Error vs. Temperature -25 0 25 50 75 TEMPERATURE - C 100 150 Figure 18. Power-Down Current vs. Temperature -6- REV. 0 AD7801 TERMINOLOGY Integral Nonlinearity AD7801 REFERENCE AMPLIFIER VDD For the DAC, Relative Accuracy or End-Point nonlinearity is a measure of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. A graphical representation of the transfer curve is shown in Figure 14. 11.7k 30k CURRENT DAC REFIN I/V VOUT 11.7k 30k Differential Nonlinearity Differential Nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of 1 LSB maximum ensures monotonicity. Zero-Code Error Zero-Code Error is the measured output voltage from VOUT of the DAC when zero code (all zeros) is loaded to the DAC latch. It is due to a combination of the offset errors in the DAC and output amplifier. Zero-code error is expressed in LSBs. Gain Error This is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from ideal expressed as a percent of the full-scale value. It includes fullscale errors but not offset errors. Digital-to-Analog Glitch Impulse Digital-to-Analog Glitch Impulse is the impulse injected into the analog output when the digital inputs change state with the DAC selected and the LDAC used to update the DAC. It is normally specified as the area of the glitch in nV-secs and measured when the digital input code is changed by 1 LSB at the major carry transition. Digital Feedthrough Digital Feedthrough is a measure of the impulse injected into the analog output of a DAC from the digital inputs of the same DAC, but is measured when the DAC is not updated. It is specified in nV-secs and measured with a full-scale code change on the data bus, i.e., from all 0s to all 1s and vice versa. Figure 19. DAC Architecture The DAC output is internally buffered and has rail-to-rail output characteristics. The output amplifier is capable of driving a load of 100 pF and 10 k to both VDD and ground. The reference selection for the DAC can be either internally generated from VDD or externally applied through the REFIN pin. A comparator on the REFIN pin detects whether the required reference is the internally generated reference or the externally applied voltage to the REFIN pin. If REFIN is connected to VDD, the reference selected is the internally generated VDD/2 reference. When an externally applied voltage is more than one volt below VDD, the comparator selection switches to the externally applied voltage on the REFIN pin. The range on the external reference input is from 1.0 V to VDD/2 V. The output voltage from the DAC is given by: N V O = 2V REF x 256 where VREF is the voltage applied to the external REFIN pin or VDD/2 when the internal reference is selected. N is the decimal equivalent of the code loaded to the DAC register and ranges from 0 to 255. VDD VTH PMOS Power Supply Rejection Ratio (PSRR) This specification indicates how the output of the DAC is affected by changes in the power supply voltage. Power supply rejection ratio is quoted in terms of % change in output per % change in VDD for full-scale output of the DAC. VDD is varied 10%. COMPARATOR INT REF REFIN EXT REF INT REF GENERAL DESCRIPTION D/A Section The AD7801 is an 8-bit voltage output digital-to-analog converter. The architecture consists of a reference amplifier and a current source DAC followed by a current-to-voltage converter capable of generating rail-to-rail voltages on the output of the DAC. Figure 19 shows a block diagram of the basic DAC architecture. REV. 0 MUX SELECTED REFERENCE OUTPUT Figure 20. Reference Selection Circuitry -7- AD7801 Reference Automatic Update Mode The AD7801 has the ability to use either an external reference applied through the REFIN pin or an internal reference generated from VDD. Figure 20 shows the reference input arrangement where either the internal VDD/2 or the externally applied reference can be selected. In this mode of operation the LDAC signal is permanently tied low. The state of the LDAC is sampled on the rising edge of WR. LDAC being low allows the DAC register to be automatically updated on the rising edge of WR. The output update occurs on the rising edge of WR. Figure 23 shows the timing associated with the automatic update mode of operation and also the status of the various registers during this frame. The internal reference is selected by tying the REFIN pin to VDD. If an external reference is to be used, this can be directly applied to the REFIN pin and if this is 1 V below VDD, the internal circuitry will select this externally applied reference as the reference source for the DAC. CS WR Digital Interface The AD7801 contains a fast parallel interface allowing this DAC to interface to industry standard microprocessors, microcontrollers and DSP machines. There are two modes in which this parallel interface can be configured to update the DAC output. The synchronous update mode allows synchronous updating of the DAC output; the automatic update mode allows the DAC to be updated individually following a write cycle. Figure 21 shows the internal logic associated with the digital interface. The PON STRB signal is internally generated from the power-on reset circuitry and is low during the poweron reset phase of the power up procedure. D7-D0 LDAC = 0 I/P REG (MLE) DAC REG (SLE) TRACK HOLD HOLD TRACK Figure 23. Timing and Register Arrangement for Automatic Update Mode CLR Synchronous Update Mode In this mode of operation the LDAC signal is used to update the DAC output to synchronize with other updates in the system. The state of the LDAC is sampled on the rising edge of WR. If LDAC is high, the automatic update mode is disabled and the DAC latch is updated at any time after the write by taking LDAC low. The output update occurs on the falling edge of LDAC. LDAC must be taken back high again before the next data transfer takes place. Figure 24 shows the timing associated with the synchronous update mode of operation and also the status of the various registers during this frame. PON STRB CLEAR SET SLE DAC CONTROL LDAC LOGIC TRACK VOUT CLR LDAC HOLD MLE SLE ENABLE CS WR Figure 21. Logic Interface The AD7801 has a double buffered interface, which allows for synchronous updating of the DAC output. Figure 22 shows a block diagram of the register arrangement within the AD7801. CS 15 15 DRIVERS 15 DRIVERS 4 DAC REGISTER 8 4 TO 15 DECODER INPUT REGISTER DB7-DB0 15 DAC REGISTER 4 TO 15 DECODER WR 4 30 D7-D0 UPPER NIBBLE LDAC I/P REG (MLE) HOLD TRACK HOLD 30 DAC REG (SLE) HOLD TRACK HOLD LOWER NIBBLE VOUT MLE CS WR LDAC CLR SLE Figure 24. Timing and Register Arrangement for Synchronous Update Mode CONTROL LOGIC Figure 22. Register Arrangement -8- REV. 0 AD7801 POWER-ON RESET The AD7801 has a power-on reset circuit designed to allow output stability during power up. This circuit holds the DAC in a reset state until a write takes place to the DAC. In the reset state all zeros are latched into the input register of the DAC and the DAC register is in transparent mode thus the output of the DAC is held at ground potential until a write takes place to the DAC. The power-on reset circuitry generates a PON STRB signal which is a gating signal used within the logic to identify a power-on condition. N V OUT = 2 xV REF 256 where: N is the decimal equivalent of the binary input code. N ranges from 0 to 255. VREF is the voltage applied to the external REFIN pin when the external reference is selected and is VDD/2 if the internal reference is used. Table I. Output Voltage for Selected Input Codes POWER-DOWN FEATURES The AD7801 has a power-down feature implemented by exercising the external PD pin. An active low signal puts the complete DAC into power-down mode. When in power-down, the current consumption of the device is reduced to less than 1 A max at +25C or 2 A max over temperature, making the device suitable for use in portable battery powered equipment. The internal reference resistors, the reference bias servo loop, the output amplifier and associated linear circuitry are all shut down when the power-down is activated. The output terminal sees a load of 23 k to GND when in power-down mode as shown in Figure 25. The contents of the data register are unaffected when in power-down mode. The device typically comes out of power-down in 13 s (see Figure 10). Digital MSB . . . LSB Analog Output 1111 1111 2x 255 xV REF V 256 1111 1110 2x 254 xV REF V 256 1000 0001 2x 129 xV REF V 256 1000 0000 VREF V 0111 1111 2x 127 xV REF V 256 0000 0001 2x V REF V 256 0000 0000 0V 11.7k VDD IDAC 2VREF 11.7k DAC OUTPUT VOLTAGE VREF Figure 25. Output Stage During Power-Down Analog Outputs The AD7801 contains a voltage output DAC with 8-bit resolution and rail-to-rail operation. The output buffer provides a gain of two at the output. Figures 2, 3 and 4 show the source and sink capabilities of the output amplifier. The slew rate of the output amplifier is typically 7.5 V/s and has a full-scale settling to eight bits with a 100 pF capacitive load in typically 1.2 s. 0 DAC INPUT CODE The input coding to the DAC is straight binary. Table I shows the binary transfer function for the AD7801. Figure 26 shows the DAC transfer function for binary coding. Any DAC output voltage can be expressed as: REV. 0 VREF 00 01 7F 80 81 FE FF Figure 26. DAC Transfer Function -9- AD7801 Figure 27 shows a typical setup for the AD7801 when using its internal reference. The internal reference is selected by tying the REFIN pin to VDD. Internally in the reference section there is a reference detect circuit that will select the internal VDD/2 based on the voltage connected to the REFIN pin. If REFIN is within a threshold voltage of a PMOS device (approximately 1 V) of VDD the internal reference is selected. When the REFIN voltage is more than 1 V below VDD, the externally applied voltage at this pin is used as the reference for the DAC. The internal reference on the AD7801 is VDD/2, the output current to voltage converter within the AD7801 provides a gain of two. Thus the output range of the DAC is from 0 V to VDD, based on Table I. MICROPROCESSOR INTERFACING AD7801-ADSP-2101/ADSP-2103 Interface Figure 29 shows an interface between the AD7801 and the ADSP2101/ADSP-2103. The fast interface timing associated with the AD7801 allows easy interface to the ADSP-2101/ADSP-2103. LDAC is permanently tied low in this circuit so the DAC output is updated on the rising edge of the WR signal. Data is loaded to the AD7801 input register using the following ADSP-21xx instruction. DM(DAC) = MR0 MR0 = ADSP-21xx MR0 Register. DAC = Decoded DAC Address. VDD = 3V TO 5V DMA14 0.1mF 10mF ADDRESS BUS DMA0 AD7801* VDD REF IN EN ADDR DECODE ADSP-2101*/ ADSP-2103* VOUT AD7801 CLR DMS AGND DGND VOUT LDAC WR WR PD D7-D0 CS WR CS LDAC DB7 VDD DB0 DATA BUS CONTROL INPUTS DMD15 DATA BUS DMD0 Figure 27. Typical Configuration Selecting the Internal Reference Figure 28 shows a typical setup for the AD7801 when using an external reference. The reference range for the AD7801 is from 1 V to VDD/2 V. Higher values of reference can be incorporated but will saturate the output at both the top and bottom end of the transfer function. There is a gain of two from input to output on the AD7801. Suitable references for 5 V operation are the AD780 and REF192. For 3 V operation a suitable external reference would be the AD589 a 1.23 V bandgap reference. *ADDITIONAL CIRCUITRY OMITTED FOR CLARITY. Figure 29. AD7801-ADSP-2101/ADSP-2103 Interface AD7801-TMS320C20 Interface Figure 30 shows an interface between the AD7801 and the TMS320C20. Data is loaded to the AD7801 using the following instruction: OUT DAC, D DAC = Decoded DAC Address. D = Data Memory Address. VDD = 3V TO 5V A15 0.1mF 10mF ADDRESS BUS A0 VIN EXT REF VOUT GND VDD REF IN 0.1mF CLR AD7801* AGND DGND IS AD7801 VOUT D7-D0 ADDR DECODE LDAC STRB CS WR WR LDAC VDD R/W DATA BUS CS TMS320C20 VOUT PD AD780/REF192 WITH VDD = 5V OR AD589 WITH VDD = 3V EN DB7 DB0 CONTROL INPUTS D15 DATA BUS Figure 28. Typical Configuration Using An External Reference D0 *ADDITIONAL CIRCUITRY OMITTED FOR CLARITY. Figure 30. AD7801-TMS320C20 Interface -10- REV. 0 AD7801 In the circuit shown the LDAC is hardwired low thus the DAC output is updated on the rising edge of WR. Some applications may require synchronous updating of the DAC in the AD7801. In this case the LDAC signal can be driven from an external timer or can be controlled by the microprocessor. One option for synchronous updating is to decode the LDAC from the address bus so a write operation at this address will synchronously update the DAC output. A simple OR gate with one input driven from the decoded address and the second input from the WR signal will implement this function. AD7801-8051/8088 Interface VDD = 3V TO 5V 0.1mF R4 20k 10mF R3 10k VIN EXT REF VOUT REF IN 0.1mF GND CLR AD820/ OP295 VDD AGND DGND D7-D0 -5V AD7801 R1 10k CS WR LDAC R2 20k VDD Figure 31 shows a serial interface between the AD7801 and the 8051/8088 processors. 5V VOUT PD AD780/REF192 WITH VDD = 5V OR AD589 WITH VDD = 3V +5V DATA BUS CONTROL INPUTS Figure 32. Bipolar Operation Using the AD7801 A15 Decoding Multiple AD7801s in a System ADDRESS BUS A8 AD7801* ADDR DECODE EN PSEN OR DEN WR WR LDAC 8051/8088* ALE CS OCTAL LATCH DB7 DB0 AD7 DATA BUS AD0 *ADDITIONAL CIRCUITRY OMITTED FOR CLARITY. The CS pin on the AD7801 can be used in applications to decode a number of DACs. In this application, all DACs in the system receive the same input data, but only the CS to one of the DACs will be active at any one time allowing access to one channel in the system. The 74HC139 is used as a two-to-four line decoder to address any of the DACs in the system. To prevent timing errors from occurring, the Enable input on the 74HC139 should be brought to its inactive state while the Coded Address inputs are changing state. Figure 33 shows a diagram of a typical setup for decoding multiple AD7801 devices in a system. The built-in power-on reset circuit on the AD7801 ensures that the outputs of all DACs in the system power up with zero volts on their outputs. Figure 31. AD7801-8051/8088 Interface AD7801 DATA BUS APPLICATIONS Bipolar Operation Using the AD7801 WR VOUT WR The AD7801 has been designed for unipolar operation but bipolar operation is possible using the circuit in Figure 32. The circuit shown is configured for an output voltage range of -5 V to +5 V. Rail-to-rail operation at the amplifier output is achievable by using an AD820 or OP295 as the output amplifier. D0 D7 VDD 1G VCC 1Y0 ENABLE 1A 1B The output voltage for any input code can be calculated as follows: CODED ADDRESS 1Y1 1Y2 WR 74HC139 ) LDAC AD7801 CS 1Y3 R4 2V REF D R4 -V REF V O = R2 1+ / R1+ R2 x 256 R3 R3 ( CS D0 D7 VOUT LDAC DGND AD7801 CS Where D is the decimal equivalent of the code loaded to the DAC and VREF is the reference voltage input. VOUT WR D0 D7 With VREF = 2.5 V, R1 = R3 = 10 k and R2 = R4 = 20 k and VDD = 5 V. 10D VO = -5 256 LDAC AD7801 CS VOUT WR D0 D7 LDAC Figure 33. Decoding Multiple AD7801s REV. 0 -11- AD7801 VDD = 5V AD7801 as a Digitally Programmable Indicator A digitally programmable upper limit detector using the DAC is shown in Figure 34. The upper limit for the test is loaded to the DAC, which in turn sets the limit for the CMP04. If a signal at the VIN input is not below the programmed value, an LED will indicate the Fail condition. VSOURCE 0.1F 10F LOAD VIN EXT REF VOUT VDD REF IN +5V VOUT 0.1F GND 2N3904/ BC107 AD820/ OP295 AD7801 +5V 10 F 0.1 F VDD VIN 1k FAIL AD780/ REF192 WITH VDD = 5V 1k PASS AGND DGND 4.7k REFIN 470 AD7801 VOUT D7 Figure 35. Programmable Current Source PASS/ D0 Coarse and Fine Adjustment using two AD7801s 1/4 CMP-04 DVDD DGND 1/6 74HC05 AGND Figure 34. Digitally Programmable Indicator Programmable Current Source Figure 35 shows the AD7801 used as the control element of a programmable current source. In this circuit the full-scale current is set to 1 mA. The output voltage from the DAC is applied across the current setting resistor of 4.7 k in series with the full-scale setting resistor of 470 . Suitable transistors to place in the feedback loop of the amplifier include the BC107 and the 2N3904, which enable the current source to operate from a minimum VSOURCE of 6 V. The operating range is determined by the operating characteristics of the transistor. Suitable amplifiers include the AD820 and the OP295, both of which have rail-to-rail operation on their outputs. The current for any digital input code can be calculated as follows: I= The two DACs can be paired together to form a coarse and fine adjustment function for a setpoint as shown in Figure 36. In this circuit, the first DAC is used to provide the coarse adjustment and the second DAC is used to provide the fine adjustment. Varying the ratio of R1 and R2 will vary the relative effect of the coarse and fine tune elements in the circuit. For the resistor values shown, the second DAC has a resolution of 148 V giving a fine tune range of 38 mV (approximately 2 LSB) for operation with a VDD of 5 V and a reference of 2.5 V. The amplifier shown allows a rail-to-rail output voltage to be achieved on the output. A typical application for the circuit would be in a setpoint controller. (2 V REF D ) (256 (5 k)) VDD = 5V R3 51.2k 0.1F R4 390 10F +5V VIN EXT REF VOUT GND REF IN 0.1F R1 390 VDD AD820/ OP295 VO VOUT AD7801 AGND DGND AD780/ REF192 WITH VDD = 5V OR AD589 WITH VDD = 3V REF IN 0.1F VDD VOUT AD7801 R2 51.2k AGND DGND Figure 36. Coarse and Fine Adjustment -12- REV. 0 AD7801 Power Supply Bypassing and Grounding In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board on which the AD7801 is mounted should be designed so that the analog and digital sections are separated and confined to certain areas of the board. If the AD7801 is in a system where multiple devices require an AGND to DGND connection, the connection should be made at one point only, a star ground point which should be established as closely as possible to the AD7801. The AD7801 should have ample supply bypassing of 10 F in parallel with 0.1 F located as close to the package as possible, ideally right up against the device. The 10 F capacitors are the tantalum bead type. The 0.1 F capacitors should have low Effective Series Resistance (ESR) and Effective Series Inductance (ESI), such as the common ceramic types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. REV. 0 The power supply lines of the AD7801 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the supply line. Fast switching signals like clocks should be shielded with digital ground to avoid radiating noise to other parts of the board and should never be run near reference inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effect of feedthrough through the board. A microstrip technique is by far the best, but not always possible with a double-sided board. In this technique, the component side of the board is dedicated to the ground plane while signal traces are placed on the solder side. -13- AD7801 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 20-Lead Wide Body SOIC (R-20) 11 1 10 PIN 1 0.4193 (10.65) 0.3937 (10.00) 20 0.2992 (7.60) 0.2914 (7.40) 0.5118 (13.00) 0.4961 (12.60) 0.1043 (2.65) 0.0926 (2.35) 0.0291 (0.74) x 45 0.0098 (0.25) 8 0.0500 0.0192 (0.49) 0 (1.27) 0.0138 (0.35) SEATING 0.0125 (0.32) PLANE BSC 0.0091 (0.23) 0.0118 (0.30) 0.0040 (0.10) 0.0500 (1.27) 0.0157 (0.40) 20-Lead TSSOP (RU-20) 0.260 (6.60) 0.252 (6.40) 11 0.256 (6.50) 0.246 (6.25) 0.177 (4.50) 0.169 (4.30) 20 1 0.006 (0.15) 0.002 (0.05) SEATING PLANE 10 PIN 1 0.0433 (1.10) MAX 0.0256 (0.65) BSC 0.0118 (0.30) 0.0075 (0.19) -14- 0.0079 (0.20) 0.0035 (0.090) 8 0 0.028 (0.70) 0.020 (0.50) REV. 0 -15- -16- PRINTED IN U.S.A. C2995-12-4/97