Order Now Product Folder Support & Community Tools & Software Technical Documents LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 LM3880 Three-Rail Simple Power Sequencer 1 Features 3 Description * * The LM3880 simple power supply sequencer offers the easiest method to control power up sequencing and power down sequencing of multiple Independent voltage rails. By staggering the startup sequence, it is possible to avoid latch conditions or large in-rush currents that can affect the reliability of the system. 1 * * * * * * Qualified for Automotive Applications Simple Solution for Sequencing 3 Voltage Rails from a Single Input Signal Easily Cascade up to 3 Devices to Sequence as Many as 9 Voltage Rails Power-Up and Power-Down Control Tiny 2.9-mm x 1.9-mm Footprint Low Quiescent Current of 25 A Input Voltage Range of 2.7 V to 5.5 V Standard Timing Options Available Available in a 6-pin SOT-23-6 package, the Simple Sequencer contains a precision enable pin and three open-drain output flags. The open-drain output flags permit that they can be pulled up to distinct voltage supplies separate from the sequencer VDD (so long as they do not exceed the recommended maximum voltage of 0.3V greater than VDD), so as to interface with ICs requiring a range of different enable signals. When the LM3880 is enabled, the three output flags will sequentially release, after individual time delays, thus permitting the connected power supplies to start up. The output flags will follow a reverse sequence during power down to avoid latch conditions. 2 Applications * * * * * * * * Advanced Driver Assistance Systems (ADAS) Automotive Camera Modules Security Cameras Servers Networking Elements FPGA Power Supply Sequencing Microprocessor and Microcontroller Sequencing Multiple Supply Sequencing EPROM capability allows every delay and sequence to be fully adjustable. Contact Texas Instruments if a nonstandard configuration is required. Device Information(1) PART NUMBER LM3880 PACKAGE DBV SOT (6) BODY SIZE (NOM) 2.90 mm x 1.60 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. Simple Power Supply Sequencing Input Supply 1 VCC Enable 3 FLAG1 6 FLAG2 5 FLAG3 4 EN GND Enable Power Supply 1 Enable Power Supply 2 Enable Power Supply 3 2 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 4 4 4 4 5 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description .............................................. 9 7.1 Overview ................................................................... 9 7.2 Functional Block Diagram ......................................... 9 7.3 Feature Description................................................... 9 7.4 Device Functional Modes........................................ 12 8 Application and Implementation ........................ 13 8.1 Application Information............................................ 13 8.2 Typical Application .................................................. 13 8.3 Do's and Don'ts ...................................................... 15 9 Power Supply Recommendations...................... 17 10 Layout................................................................... 17 10.1 Layout Guidelines ................................................. 17 10.2 Layout Example .................................................... 17 11 Device and Documentation Support ................. 19 11.1 11.2 11.3 11.4 11.5 Device Support...................................................... Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 19 20 20 20 20 12 Mechanical, Packaging, and Orderable Information ........................................................... 20 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision K (February 2016) to Revision L Page * Updated Features to specify how many rails can be sequenced by a single device ............................................................ 1 * Added feature that devices can be cascaded ....................................................................................................................... 1 * Specified device dimensions in Features ............................................................................................................................... 1 * Specified FPGA Power Supply Sequencing in Applications .................................................................................................. 1 * Added note in description about open drain FLAG pins......................................................................................................... 1 * Added I/O column to Pin Functions table ............................................................................................................................... 3 * Changed Part Nomenclature section to Device Nomenclature section................................................................................ 19 Changes from Revision J (December 2014) to Revision K Page * Changed Handling Ratings to ESD Ratings and moved storage temperature to Absolute Maximum Ratings ..................... 4 * Removed "Customized Timing and Sequence" section ...................................................................................................... 12 * Added cross references to timing diagrams ......................................................................................................................... 19 Changes from Revision I (March 2013) to Revision J * Added Handling Rating table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ............................................................... 4 Changes from Revision H (March 2013) to Revision I * 2 Page Page Changed layout of National Data Sheet to TI format. .......................................................................................................... 19 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 5 Pin Configuration and Functions DBV Package 6-Pin SOT-23 Top View VCC 1 6 FLAG1 GND 2 5 FLAG2 EN 3 4 FLAG3 Pin Functions PIN NAME NO. I/O (1) DESCRIPTION EN 3 I Precision enable pin FLAG1 6 O Open-drain output 1 FLAG2 5 O Open-drain output 2 FLAG3 4 O Open-drain output 3 GND 2 G Ground VCC 1 I Input supply (1) I = input, O = output, G = ground Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 3 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature (unless otherwise noted) (1) (2) MIN MAX UNIT VCC -0.3 6 V EN, FLAG1, FLAG2, FLAG3 -0.3 6 V Maximum Flag ON current 50 mA Maximum Junction temperature 150 C 260 C 150 C Lead temperature (Soldering, 5 s) Storage temperature Tstg (1) (2) -65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. 6.2 ESD Ratings V(ESD) (1) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins VALUE UNIT 2 kV (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT V VCC to GND 2.7 5.5 EN, FLAG1, FLAG2, FLAG3 -0.3 VCC + 0.3 V Junction temperature -40 125 C 6.4 Thermal Information LM3880 THERMAL METRIC (1) DBV (SOT-23) UNIT 6 PINS RJA Junction-to-ambient thermal resistance 187.6 C/W RJC(top) Junction-to-case (top) thermal resistance 127.4 C/W RJB Junction-to-board thermal resistance 31.5 C/W JT Junction-to-top characterization parameter 23.3 C/W JB Junction-to-board characterization parameter 31.0 C/W (1) 4 For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 6.5 Electrical Characteristics Limits apply to all timing options and VCC = 3.3 V, unless otherwise specified. Minimum and Maximum limits apply over the full Operating Temperature Range (TJ = -40C to +125C) and are specified through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C and are provided for reference purposes only. PARAMETER IQ MIN (1) TEST CONDITIONS Operating Quiescent current TYP (2) MAX (1) 25 80 A 20 nA 0.4 V UNIT OPEN-DRAIN FLAGS IFLAG FLAGx Leakage Current VFLAGx = 3.3 V VOL FLAGx Output Voltage Low IFLAGx = 1.2 mA 1 POWER-UP SEQUENCE td1 Timer delay 1 accuracy td2 Timer delay 2 accuracy td3 Timer delay 3 accuracy All Other Timing Options -15% 15% 2 ms Timing Option -20% 20% All Other Timing Options -15% 15% 2 ms Timing Option -20% 20% All Other Timing Options -15% 15% 2 ms Timing Option -20% 20% All Other Timing Options -15% 15% 2 ms Timing Option -20% 20% All Other Timing Options -15% 15% 2 ms Timing Option -20% 20% All Other Timing Options -15% 15% 2 ms Timing Option -20% 20% For x = 1 or 4 95% 105% For x = 1 or 4, 2 ms option 90% 110% For x = 2 or 5 95% 105% For x = 2 or 5, 2 ms option 90% 110% POWER-DOWN SEQUENCE td4 Timer delay 4 accuracy td5 Timer delay 5 accuracy td6 Timer delay 6 accuracy TIMING DELAY ERROR (td(x) - 400 s) / td(x+1) Ratio of timing delays td(x) / td(x+1) Ratio of timing delays ENABLE PIN VEN EN pin threshold IEN EN pin pullup current (1) (2) 1.0 VEN = 0 V 1.25 1.4 7 V A Limits are 100% production tested at 25. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate TI's Average Outgoing Quality Level (AOQL). Typical numbers are at 25C and represent the most likely parametric norm. Timing Requirements EN FLAG1 FLAG2 FLAG3 td1 td2 td3 All standard options use Sequence 1 for output flags rise and fall order. Refer to section 11.1.2 for details of different sequences possible. Figure 1. Power-Up Sequence Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 5 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com EN FLAG1 FLAG2 FLAG3 td4 td5 td6 All standard options use Sequence 1 for output flags rise and fall order. Refer to section 11.1.2 for details of different sequences possible. Figure 2. Power-Down Sequence 6 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 6.6 Typical Characteristics 30 26 29 25 28 24 26 IQ (PA) IQ (PA) 27 25 23 24 22 23 22 21 21 20 2.5 3 3.5 4 4.5 5 20 -40 -25 -10 5 20 35 50 65 80 95 110 125 5.5 TEMPERATURE (oC) VCC (V) Figure 3. Quiescent Current vs VCC Figure 4. Quiescent Current vs Temperature (VCC = 3.3 V) 1.232 1.230 1.228 VEN (V) 1.226 1.224 RISING FALLING 1.222 1.220 1.218 1.216 1.214 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) Figure 5. Enable Threshold vs Temperature Figure 6. Time Delay (30 ms) vs Vcc Figure 7. Time Delay Ratio vs Temperature Figure 8. Time Delay (30 ms) vs Temperature Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 7 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com Typical Characteristics (continued) Figure 9. Flag VOL vs Vcc (RFLAG = 100 k) 8 Submit Documentation Feedback Figure 10. Flag Voltage vs Current Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 7 Detailed Description 7.1 Overview The LM3880 simple power supply sequencer provides a simple solution for sequencing multiple rails in a controlled manner. Six independent timers are integrated to control the timing sequence (power up and power down) of three open-drain output flags. These flags permit connection to either a shutdown or enable pin of linear regulators and switchers to control the operation of the power supplies. This allows design of a complete power system without concern for large inrush currents or latch-up conditions that can occur. The timing sequence of the device is controlled entirely by the enable (EN) pin. Upon power up, all the flags are held low until this precision enable is pulled high. When the EN pin is asserted, the power-up sequence starts. An internal counter delays the first flag (FLAG1) from rising until a fixed time period has expired. When the first flag is released, another timer will begin to delay the release of the second flag (FLAG2). This process repeats until all three flags have sequentially been released. The power-down sequence is the same as power-up sequence, but in reverse. When the EN pin is deasserted a timer will begin that delays the third flag (FLAG3) from pulling low. The second and first flag will then follow in a sequential manner after their appropriate delays. The three timers that are used to control the power-down scheme can also be individually programmed and are completely independent of the power-up timers. 7.2 Functional Block Diagram VCC FLAG1 7 A EN tD1 tD2 + 1.25 V FLAG2 tD3 Timing Delay Generation tD4 Sequence Control tD5 Master Clock FLAG3 tD6 EEPROM (Factory Set) GND 7.3 Feature Description 7.3.1 Enable Pin Operation The timing sequence of the LM3880 is controlled by the assertion of the enable signal. The enable pin is designed with an internal comparator, referenced to a bandgap voltage (1.25 V), to provide a precision threshold. This allows a delayed timing to be externally set using a capacitor or to start the sequencing based on a certain event, such as a line voltage reaching 90% of nominal. For an additional delayed sequence from the rail powering VCC, simply attach a capacitor to the EN pin as shown in Figure 11. Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 9 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com Feature Description (continued) 7 A EN + CEN Enable 1.25 V Figure 11. Capacitor Timing Using the internal pullup current source to charge the external capacitor (CEN) the enable pin delay can be calculated by Equation 1: tenable_delay = 1.25V x CEN 7 PA (1) A resistor divider can also be used to enable the device based on a certain voltage threshold. Take care when sizing the resistor divider to include the effects of the internal current source. One of the features of the EN pin is that it provides glitch free operation. The first timer will start counting at a rising threshold, but will always reset if the EN pin is deasserted before the first output flag is released. This can be shown in Figure 12: EN FLAG1 td1 Figure 12. EN Glitch 7.3.2 Incomplete Sequence Operation If the enable signal remains high for the entire power-up sequence, then the part will operate as shown in the standard timing diagrams. However, if the enable signal is de-asserted before the power-up sequence is completed the part will enter a controlled shutdown. This allows the system to walk through a controlled power cycling, preventing any latch conditions from occurring. This state only occurs if the enable pin is deasserted after the completion of timer 1, but before the entire power-up sequence is completed. When this event occurs, the falling edge of EN pin resets the current timer and will allow the remaining power-up cycle to complete before beginning the power-down sequence. The power down sequence starts approximately 120 ms after the final power-up flag. This allows output voltages in the system to stabilize before everything is shut down. An example of this operation can be seen in Figure 13: 10 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 Feature Description (continued) EN FLAG1 FLAG2 FLAG3 td1 td2 td3 120 ms td4 td5 td6 Figure 13. Incomplete Power-Up Sequence When the enable signal is deasserted, the part will commence its power-down sequence. If the enable signal is pulled high before the power-down sequence is completed, the part will ensure completion of the power-down sequence before starting power-up. This ensures that the system does not partially power down and power up and helps prevent latch-up events, such as in FPGAs and microprocessors. This state only occurs if the enable pin is pulled high after the completion of timer 1, but before the entire power-down sequence is completed. When this event occurs, the rising edge of enable pin resets the current timer and will allow the remaining powerdown cycle to complete before beginning the power-up sequence. The power-up sequence starts approximately 120 ms after the final power-down flag. This allows the system to fully shut down before it is powered up. An example of this operation can be seen in Figure 14: EN FLAG1 FLAG2 FLAG3 td1t t td2t t td3t t t120 mst td4t td5t t t td6t t Figure 14. Incomplete Power-Down Sequence All the internal timers are generated by a master clock that has an extremely low tempco. This allows for tight accuracy across temperature and a consistent ratio between the individual timers. There is a slight additional delay of approximately 400 s to timers 1 and 4, which is a result of the EPROM refresh. This refresh time is in addition to the programmed delay time and will be almost insignificant to all but the shortest of timer delays. Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 11 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com 7.4 Device Functional Modes 7.4.1 Power Up With EN Pin The timing sequence of the Simple Power Supply Sequencer is controlled entirely by the enable (EN) pin. Upon power up, all the flags are held low until this precision enable is pulled high. After the EN pin is asserted, the power-up sequence will commence. 7.4.2 Power Down With EN Pin When EN pin is deasserted, the power down sequence will commence. A timer will begin that delays the third flag (FLAG3) from pulling low. The second and first flag will then follow in a sequential manner after their appropriate delays. 12 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information 8.1.1 Open Drain Flags Pullup The Simple Power Supply Sequencer contains three open-drain output flags which need to be pulled up for proper operation. 100-k resistors can be used as pullup resistors. 8.1.2 Enable the Device See Enable Pin Operation. 8.2 Typical Application 8.2.1 Simple Sequencing of Three Power Supplies The Simple Power Supply Sequencer is used to implement a power-up and power-down sequence of three power supplies. Sequence 1 for the LM3880, e.g. orderable part number LM3880MF-1AA has a power-up sequence (1 - 2 - 3) and power-down sequence (3 - 2 -1). See Table 3 and Table 4 for other sequence options or contact TI if other sequence options are desired. Figure 15. Typical Application Circuit Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 13 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com Typical Application (continued) 8.2.1.1 Design Requirements For this design example, use the parameters listed in Table 1 as the input parameters. The circuit shown in Figure 15 can have various power-down sequences depending on the sequence the part is programmed for. See Table 3 for different power-down sequence options. Table 1. Design Parameters DESIGN PARAMETER EXAMPLE VALUE Input Supply voltage range 2.7 V to 5.5 V Flag Output voltage, EN high Input Supply Flag Output voltage, EN low 0V Flag Timing Delay 30 ms Power-Up Sequence 1-2-3 Power-Down Sequence 3-2-1 8.2.1.2 Detailed Design Procedure Table 2. Bill of Materials DESIGNATOR DESCRIPTION DEVICE QUANTITY MANUFACTURER U1 R1 LM3880, Sequence 1, 30 ms timing LM3880 1 Texas Instruments 100-k Resistor, 0603 CRCW0603100KFKEA 1 Vishay R2 100-k Resistor, 0603 CRCW0603100KFKEA 1 Vishay R3 100-k Resistor, 0603 CRCW0603100KFKEA 1 Vishay This application uses the Sequence 1 and 30-ms timing options of the Simple Power Supply Sequencer. See Application Curves for details on the sequence and timing option. 8.2.1.3 Application Curves Figure 16. Power-Up Sequence for LM3880MF-1AE 14 Submit Documentation Feedback Figure 17. Power-Down Sequence for LM3880MF-1AE Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 8.2.2 Sequencing Using Independent Flag Supply For applications requiring a flag output voltage that is different from the VCC, a separate Flag Supply may be used to pullup the open-drain outputs of the simple power supply sequencer. This is useful when interfacing the flag outputs with inputs that require a different voltage than VCC. The designer must ensure the flag supply voltage is not taken above VCC + 0.3 V as specified in the Recommended Operating Conditions. Figure 18. Sequencing Using Independent Flag Supply 8.3 Do's and Don'ts Connecting the EN pin to VCC is not recommended. During power up, the EN voltage should be kept below the EN threshold until VCC rises above the minimum operating voltage. This will be violated if EN is connected to VCC, and undefined operation at the flag outputs can occur, especially during slow VCC rising slew rates. For systems requiring only power-up sequencing, a capacitor at the EN pin can be used to create a delay or a resistor divider can be used to enable the device based on a certain voltage threshold. While these solutions will work for power-up, it will not power-down the flag outputs in sequential fashion since the flag outputs will simply follow the input supply. For systems requiring both power-up and power-down sequencing, an external enable signal should be used, such as a GPIO signal from a microcontroller, to properly control power-up and powerdown of the flag outputs. Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 15 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com Do's and Don'ts (continued) Figure 19. Recommended EN Connection 16 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 9 Power Supply Recommendations The VCC pin should be located as close as possible to the input supply (2.7-5.5 V). An input capacitor is not required but is recommended when noise might be present on the VCC pin. A 0.1-F ceramic capacitor may be used to bypass this noise. 10 Layout 10.1 Layout Guidelines * * Pullup resistors should be connected between the flag output pins and a positive input supply, usually VCC. An independent flag supply may also be used. These resistors should be placed as close as possible to the Simple Power Supply Sequencer and the flag supply. Minimal trace length is recommended to make the connections. A typical value for the pullup resistors is 100 k. For very tight sequencing requirements, minimal and equal trace lengths should be used to connect the flag outputs to the desired inputs. This will reduce any propagation delay and timing errors between the flag outputs along the line. 10.2 Layout Example Figure 20 and Figure 21 are layout examples for the LM3880. These examples are taken from the LM3880EVAL. Figure 20. LM3880 Top Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 17 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com Layout Example (continued) Figure 21. LM3880 Bottom 18 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 LM3880 www.ti.com SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.1.2 Device Nomenclature The list of parts available to order appear in the Package Option Addendum. Figure 22. Device Nomenclature Table 3. Sequence Designator Table FLAG ORDER SEQUENCE NUMBER (1) (1) POWER UP POWER DOWN 1 1-2-3 3-2-1 2 1-2-3 3-1-2 3 1-2-3 2-3-1 4 1-2-3 2-1-3 5 1-2-3 1-3-2 6 1-2-3 1-2-3 See Figure 1 and Figure 2. Table 4. Timing Designator Table (1) TIMING DESIGNATOR (1) DELAYS (ms) td1 td2 td3 td4 td5 td6 AA 10 10 10 10 10 10 30 AB 30 30 30 30 30 AC 60 60 60 60 60 60 AD 120 120 120 120 120 120 AE 2 2 2 2 2 2 AF 16 16 16 16 16 16 See Figure 1 and Figure 2. Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 19 LM3880 SNVS451L - AUGUST 2006 - REVISED NOVEMBER 2018 www.ti.com 11.2 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.3 Trademarks E2E is a trademark of Texas Instruments. 11.4 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.5 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 20 Submit Documentation Feedback Copyright (c) 2006-2018, Texas Instruments Incorporated Product Folder Links: LM3880 PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM3880MF-1AA NRND SOT-23 DBV 6 1000 TBD Call TI Call TI -40 to 125 F20A LM3880MF-1AA/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F20A LM3880MF-1AB/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F21A LM3880MF-1AC/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F22A LM3880MF-1AD/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F23A LM3880MF-1AE/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F25A LM3880MF-1AF/NOPB ACTIVE SOT-23 DBV 6 1000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F31A LM3880MFE-1AA/NOPB ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F20A LM3880MFE-1AB/NOPB ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F21A LM3880MFE-1AC/NOPB ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F22A LM3880MFE-1AD/NOPB ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F23A LM3880MFE-1AE/NOPB ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F25A LM3880MFE-1AF/NOPB ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F31A LM3880MFX-1AA/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F20A LM3880MFX-1AB/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F21A LM3880MFX-1AC/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F22A LM3880MFX-1AD/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F23A Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 6-Feb-2020 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM3880MFX-1AE/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F25A LM3880MFX-1AF/NOPB ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 F31A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LM3880 : Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 * Automotive: LM3880-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LM3880MF-1AA SOT-23 DBV 6 1000 178.0 8.4 LM3880MF-1AA/NOPB SOT-23 DBV 6 1000 178.0 LM3880MF-1AB/NOPB SOT-23 DBV 6 1000 178.0 LM3880MF-1AC/NOPB SOT-23 DBV 6 1000 LM3880MF-1AD/NOPB SOT-23 DBV 6 LM3880MF-1AE/NOPB SOT-23 DBV LM3880MF-1AF/NOPB SOT-23 DBV LM3880MFE-1AA/NOPB SOT-23 W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 DBV 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFE-1AB/NOPB SOT-23 DBV 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFE-1AC/NOPB SOT-23 DBV 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFE-1AD/NOPB SOT-23 DBV 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFE-1AE/NOPB SOT-23 DBV 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFE-1AF/NOPB SOT-23 DBV 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFX-1AA/NOPB SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFX-1AB/NOPB SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFX-1AC/NOPB SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFX-1AD/NOPB SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM3880MFX-1AE/NOPB SOT-23 DBV 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 Device LM3880MFX-1AF/NOPB Package Package Pins Type Drawing SPQ SOT-23 3000 DBV 6 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 178.0 8.4 3.2 B0 (mm) K0 (mm) P1 (mm) 3.2 1.4 4.0 W Pin1 (mm) Quadrant 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM3880MF-1AA SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MF-1AA/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MF-1AB/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MF-1AC/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MF-1AD/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MF-1AE/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MF-1AF/NOPB SOT-23 DBV 6 1000 210.0 185.0 35.0 LM3880MFE-1AA/NOPB SOT-23 DBV 6 250 210.0 185.0 35.0 LM3880MFE-1AB/NOPB SOT-23 DBV 6 250 210.0 185.0 35.0 LM3880MFE-1AC/NOPB SOT-23 DBV 6 250 210.0 185.0 35.0 LM3880MFE-1AD/NOPB SOT-23 DBV 6 250 210.0 185.0 35.0 LM3880MFE-1AE/NOPB SOT-23 DBV 6 250 210.0 185.0 35.0 LM3880MFE-1AF/NOPB SOT-23 DBV 6 250 210.0 185.0 35.0 LM3880MFX-1AA/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 LM3880MFX-1AB/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 LM3880MFX-1AC/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 29-Sep-2019 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM3880MFX-1AD/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 LM3880MFX-1AE/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 LM3880MFX-1AF/NOPB SOT-23 DBV 6 3000 210.0 185.0 35.0 Pack Materials-Page 3 PACKAGE OUTLINE DBV0006A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 6 2X 0.95 1.9 1.45 MAX 3.05 2.75 5 2 4 0.50 6X 0.25 0.2 C A B 3 (1.1) 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214840/B 03/2018 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 per side. 4. Leads 1,2,3 may be wider than leads 4,5,6 for package orientation. 5. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0006A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 6X (1.1) 1 6X (0.6) 6 SYMM 2 5 3 4 2X (0.95) (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214840/B 03/2018 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0006A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 6X (1.1) 1 6X (0.6) 6 SYMM 2 5 3 4 2X(0.95) (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214840/B 03/2018 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2020, Texas Instruments Incorporated