SCBS239F - MARCH 1993 - REVISED JUNE 2004 D Members of the Texas Instruments D D D D D D D SN54ABT162245 . . . WD PACKAGE SN74ABT162245 . . . DGG OR DL PACKAGE (TOP VIEW) Widebus Family A-Port Outputs Have Equivalent 25- Series Resistors, So No External Resistors Are Required Typical VOLP (Output Ground Bounce) <1 V at VCC = 5 V, TA = 25C Distributed VCC and GND Pins Minimize High-Speed Switching Noise Ioff Supports Partial-Power-Down Mode Operation Flow-Through Architecture Optimizes PCB Layout Latch-Up Performance Exceeds 500 mA Per JESD 17 ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) 1DIR 1B1 1B2 GND 1B3 1B4 VCC 1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCC 2B5 2B6 GND 2B7 2B8 2DIR description/ordering information The 'ABT162245 devices are 16-bit noninverting 3-state transceivers designed for synchronous two-way communication between data buses. The control-function implementation minimizes external timing requirements. 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 GND 1A7 1A8 2A1 2A2 GND 2A3 2A4 VCC 2A5 2A6 GND 2A7 2A8 2OE These devices can be used as two 8-bit transceivers or one 16-bit transceiver. They allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so that the buses effectively are isolated. The A-port outputs, which are designed to source or sink up to 12 mA, include equivalent 25- series resistors to reduce overshoot and undershoot. These devices are fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. ORDERING INFORMATION TA -40C 85C -40 C to 85 C -55C to 125C ORDERABLE PART NUMBER PACKAGE Tube SN74ABT162245DL Tape and reel SN74ABT162245DLR TSSOP - DGG Tape and reel SN74ABT162245DGGR CFP - WD Tube SNJ54ABT162245WD SSOP - DL TOP-SIDE MARKING ABT162245 ABT162245 SNJ54ABT162245WD Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright 2004, Texas Instruments Incorporated !" # $%&" !# '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ '*%$"# $')!" " 12 3 4 !)) '!!&"&# !& "&#"&* %)&## ",&.#& "&*+ !)) ",& '*%$"# '*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SCBS239F - MARCH 1993 - REVISED JUNE 2004 description/ordering information (continued) To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. FUNCTION TABLE (each 8-bit section) INPUTS OE DIR OPERATION L L B data to A bus L H A data to B bus H X Isolation logic diagram (positive logic) 1DIR 1 2DIR 48 1A1 25 1OE 47 2A1 2 24 2OE 36 13 1B1 2B1 To Seven Other Channels To Seven Other Channels absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . -0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT162245 (B port) . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT162245 (B port) . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA SN54/74ABT162245 (A port) . . . . . . . . . . . . . . . . . . . . . . . 30 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Package thermal impedance, JA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCBS239F - MARCH 1993 - REVISED JUNE 2004 recommended operating conditions (see Note 3) SN54ABT162245 VCC VIH Supply voltage VIL VI Low-level input voltage High-level input voltage High-level output current IOL Low-level output current t/v Input transition rise or fall rate MIN MAX MIN MAX 4.5 5.5 4.5 5.5 2 2 0.8 Input voltage IOH SN74ABT162245 0 0 UNIT V V 0.8 V VCC -32 V B port VCC -24 A port -3 -12 B port 48 64 A port 12 12 Outputs enabled 10 10 mA mA ns/V TA Operating free-air temperature -55 125 -40 85 C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SCBS239F - MARCH 1993 - REVISED JUNE 2004 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK A port VOH B port TEST CONDITIONS VCC = 4.5 V, VCC = 5 V, II = -18 mA IOH = -1 mA B port SN54ABT162245 MIN -1.2 MAX SN74ABT162245 MIN -1.2 2.5 3.3 3 3 VCC = 4.5 V IOH = -1 mA IOH = -3 mA 3.1 3 3.1 2.6* VCC = 5 V, IOH = -12 mA IOH = -3 mA 3 3 3 IOH = -3 mA IOH = -24 mA 2.5 2.5 2.5 VCC = 4.5 V IOH = -32 mA IOL = 12 mA 2* VCC = 4.5 V 2 2 IOL = 48 mA IOL = 64 mA 0.8 0.8 0.8 0.45 0.45 0.45 0.55* VCC = 5.5 V, VI = VCC or GND mV 1 1 1 20 20 20 VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.5 V Ioff VCC = 0, VCC = 5.5 V, VO = 5.5 V VI or VO 4.5 V VCC = 5.5 V, VO = 2.5 V VCC = 5.5 V, IO = 0, VI = VCC or GND Outputs high 2 2 2 Outputs low 32 32 32 Outputs disabled 2 2 2 VCC = 5.5 V, Outputs enabled One input at 3.4 V, Other inputs at Outputs disabled VCC or GND VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND 1 2 2 0.05 1 0.05 1.5 1.5 1.5 IO ICC A port B port A or B ports Data inputs ICC# Control inputs Ci Cio 10 10 10 A -10 -10 A 100 A 50 A 50 50 -25 -50 -100 -25 -90 -25 -100 -50 -100 -180 -50 -180 -50 -180 VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V mA mA mA 3 pF 6 pF * On products compliant to MIL-PRF-38535, this parameter does not apply. All typical values are at VCC = 5 V. This limit applies only to the SN74ABT162245. The parameters IOZH and IOZL include the input leakage current. Not more than one output should be tested at a time, and the duration of the test should not exceed one second. # This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. POST OFFICE BOX 655303 A -10 100 Outputs high V 0.55 IOZH IOZL ICEX V V 100 Control inputs UNIT 2.6 A or B ports 4 MAX -1.2 2.5 Vhys II TA = 25C TYP MAX 3.8 A port VOL MIN * DALLAS, TEXAS 75265 SCBS239F - MARCH 1993 - REVISED JUNE 2004 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tPLH tPHL A B tPLH tPHL B A tPZH tPZL OE B tPHZ tPLZ OE B tPZH tPZL OE A tPHZ tPLZ OE A PARAMETER VCC = 5 V, TA = 25C SN54ABT162245 SN74ABT162245 MIN TYP MAX MIN MAX MIN MAX 1 2.2 3.4 1 4.1 1 3.9 1 2.3 3.7 1 4.4 1 4.2 1 2.7 4.1 1 4.9 1 4.6 1.5 3.1 4.6 1.5 5.2 1.5 5.1 1 3.6 5.2 1 6.4 1 6.3 1 3.7 5.4 1 6.5 1 6.4 2 4.4 5.8 2 6.4 2 6.3 1.5 3.3 4.7 1.5 5.6 1.5 5.2 1.5 4.1 6 1.5 7.2 1.5 7.1 1.5 4.3 6.1 1.5 7.3 1.5 7 2 4.5 6.1 2 6.8 2 6.6 1.5 3.7 5.1 1.5 6.1 1.5 5.7 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 UNIT ns ns ns ns ns ns 5 SCBS239F - MARCH 1993 - REVISED JUNE 2004 PARAMETER MEASUREMENT INFORMATION 7V S1 500 From Output Under Test Open GND CL = 50 pF (see Note A) 500 TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V Input 1.5 V 1.5 V th 3V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V Input 1.5 V 0V tPLH VOH Output 1.5 V VOL tPHL 1.5 V tPLZ 3.5 V 1.5 V tPZH 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V Output Waveform 1 S1 at 7 V (see Note B) tPLH VOH Output 1.5 V tPZL tPHL 1.5 V 3V Output Control Output Waveform 2 S1 at Open (see Note B) VOL + 0.3 V VOL tPHZ 1.5 V VOH - 0.3 V VOH 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) 5962-9677401QXA ACTIVE CFP WD 48 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9677401QX A SNJ54ABT162245 WD 74ABT162245DGGRE4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 74ABT162245DGGRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 74ABT162245DLRG4 ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 SN74ABT162245DGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 SN74ABT162245DL ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 SN74ABT162245DLG4 ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 SN74ABT162245DLR ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 ABT162245 SNJ54ABT162245WD ACTIVE CFP WD 48 1 TBD A42 N / A for Pkg Type -55 to 125 5962-9677401QX A SNJ54ABT162245 WD (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN54ABT162245, SN74ABT162245 : * Catalog: SN74ABT162245 * Military: SN54ABT162245 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74ABT162245DGGR TSSOP DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1 SN74ABT162245DLR SSOP DL 48 1000 330.0 32.4 11.35 16.2 3.1 16.0 32.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74ABT162245DGGR TSSOP DGG 48 2000 367.0 367.0 45.0 SN74ABT162245DLR SSOP DL 48 1000 367.0 367.0 55.0 Pack Materials-Page 2 MECHANICAL DATA MCFP010B - JANUARY 1995 - REVISED NOVEMBER 1997 WD (R-GDFP-F**) CERAMIC DUAL FLATPACK 48 LEADS SHOWN 0.120 (3,05) 0.075 (1,91) 0.009 (0,23) 0.004 (0,10) 1.130 (28,70) 0.870 (22,10) 0.370 (9,40) 0.250 (6,35) 0.390 (9,91) 0.370 (9,40) 0.370 (9,40) 0.250 (6,35) 48 1 0.025 (0,635) A 0.014 (0,36) 0.008 (0,20) 25 24 NO. OF LEADS** 48 56 A MAX 0.640 (16,26) 0.740 (18,80) A MIN 0.610 (15,49) 0.710 (18,03) 4040176 / D 10/97 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only Falls within MIL STD 1835: GDFP1-F48 and JEDEC MO -146AA GDFP1-F56 and JEDEC MO -146AB POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated