MT28FW01GABA1LPC-0AAT - MICRON TECHNOLOGY

Parallel NOR Flash Automotive Memory

MT28FW01GABA1xPC-0AAT, MT28FW01GABA1xJS-0AAT

Features

• Single-level cell (SLC) process technology

• Supply voltage

– VCC = 2.7–3.6V (program, erase, read)

– VCCQ = 1.65 - VCC (I/O buffers)

• Asynchronous random/page read

– Page size: 16 words

– Page access: 20ns (VCC = VCCQ = 2.7-3.6V)

– Random access: 105ns (VCC = VCCQ = 2.7-3.6V)

– Random access: 110ns (VCCQ = 1.65-VCC)

• Buffer program (512-word program buffer)

– 2.0 MB/s (TYP) when using full buffer program

– 2.5 MB/s (TYP) when using accelerated buffer

program (VHH)

• Word program: 25us per word (TYP)

• Block erase (128KB): 0.2s (TYP)

• Memory organization

– Uniform blocks: 128KB or 64KW each

– x16 data bus

• Program/erase suspend and resume capability

– Read from another block during a PROGRAM

SUSPEND operation

– Read or program another block during an ERASE

SUSPEND operation

• Unlock bypass, block erase, chip erase, and write to

buffer capability

• BLANK CHECK operation to verify an erased block

• CYCLIC REDUNDANCY CHECK (CRC) operation to

verify a program pattern

• VPP/WP# protection

– Protects first or last block regardless of block

protection settings

• Software protection

– Volatile protection

– Nonvolatile protection

– Password protection

• Extended memory block

– 512-word block for permanent, secure identifica-

tion

– Programmed or locked at the factory or by the

customer

• JESD47-compliant

– 100,000 (minimum) ERASE cycles per block

– Data retention: 20 years (TYP)

• Package

– 56-pin TSOP, 14mm x 20mm (JS)

– 64-ball LBGA, 13mm x 11mm (PC)

• RoHS-compliant, halogen-free packaging

• Automotive operating temperature

– Ambient: –40°C to 105°C

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Features

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Part Numbering Information

For available options, such as packages or high/low protection, or for further information, contact your Micron

sales representative. Part numbers can be verified at www.micron.com. Feature and specification comparison by

device type is available at www.micron.com/products. Contact the factory for devices not found.

Figure 1: Part Number Chart

MT 28F W 02G B B A 1

Micron Technology

Device type

28F = Embedded Parallel NOR Flash memory

(3V core, page, uniform block)

Voltage

W = 2.7–3.6V core; 1.7–3.6V I/O

Density

01G = 1Gb

02G = 2Gb

Stack

A = Single die

B = Dual die

A = Rev. A

Configuration

1 = x16

H PC 0 A AT

Production Status

Blank = Production

ES = Engineering sample

Operating Temperature

AT = –40°C to +105°C (Grade 2 AEC-Q100)

Special Options

A = Automotive quality

Security Features

0 = No extra security

Package

JS = 56-lead TSOP, 14mm x 20mm, lead-free,

halogen-free, RoHS-compliant

PC = 64-ball LBGA, 11mm x 13mm,

lead-free, halogen-free, RoHS-compliant

Block structure

H = High lock

L = Low lock

–

Device generation

B = Second generation

Die revision

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Features

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.

Contents

Important Notes and Warnings ......................................................................................................................... 7

General Description ......................................................................................................................................... 8

Automatic Power Savings Feature .................................................................................................................. 8

Signal Assignments ......................................................................................................................................... 10

Signal Descriptions ......................................................................................................................................... 12

Memory Organization .................................................................................................................................... 14

Memory Configuration ............................................................................................................................... 14

Memory Map ............................................................................................................................................. 14

Bus Operations ............................................................................................................................................... 15

Read .......................................................................................................................................................... 15

Write .......................................................................................................................................................... 15

Standby ..................................................................................................................................................... 15

Output Disable ........................................................................................................................................... 16

Reset .......................................................................................................................................................... 16

Registers ........................................................................................................................................................ 17

Data Polling Register .................................................................................................................................. 17

Read Status Register ................................................................................................................................... 22

Clear Status Register ................................................................................................................................... 23

Lock Register .............................................................................................................................................. 24

Standard Command Definitions – Address-Data Cycles .................................................................................... 26

READ and AUTO SELECT Operations .............................................................................................................. 28

READ/RESET Command ............................................................................................................................ 28

READ CFI Command .................................................................................................................................. 28

AUTO SELECT Command ........................................................................................................................... 28

Read Electronic Signature ........................................................................................................................... 29

Cyclic Redundancy Check Operation ............................................................................................................... 30

CYCLIC REDUNDANCY CHECK Command ................................................................................................. 30

Cyclic Redundancy Check Operation Command Sequence .......................................................................... 30

Bypass Operations .......................................................................................................................................... 33

UNLOCK BYPASS Command ...................................................................................................................... 33

UNLOCK BYPASS RESET Command ............................................................................................................ 33

Program Operations ....................................................................................................................................... 34

PROGRAM Command ................................................................................................................................ 34

UNLOCK BYPASS PROGRAM Command ..................................................................................................... 34

WRITE TO BUFFER PROGRAM Command .................................................................................................. 34

UNLOCK BYPASS WRITE TO BUFFER PROGRAM Command ....................................................................... 37

WRITE TO BUFFER PROGRAM CONFIRM Command .................................................................................. 37

BUFFERED PROGRAM ABORT AND RESET Command ................................................................................ 37

PROGRAM SUSPEND Command ................................................................................................................ 37

PROGRAM RESUME Command .................................................................................................................. 38

ACCELERATED BUFFERED PROGRAM Operations ...................................................................................... 38

Erase Operations ............................................................................................................................................ 39

CHIP ERASE Command .............................................................................................................................. 39

UNLOCK BYPASS CHIP ERASE Command ................................................................................................... 39

BLOCK ERASE Command ........................................................................................................................... 39

UNLOCK BYPASS BLOCK ERASE Command ................................................................................................ 40

ERASE SUSPEND Command ....................................................................................................................... 40

ERASE RESUME Command ........................................................................................................................ 41

ACCELERATED CHIP ERASE Operations ......................................................................................................... 41

BLANK CHECK Operation .............................................................................................................................. 41

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Features

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.

Device Protection ........................................................................................................................................... 43

Hardware Protection .................................................................................................................................. 43

Software Protection .................................................................................................................................... 43

Volatile Protection Mode ............................................................................................................................. 44

Nonvolatile Protection Mode ...................................................................................................................... 44

Password Protection Mode .......................................................................................................................... 44

Block Protection Command Definitions – Address-Data Cycles ........................................................................ 47

Protection Operations .................................................................................................................................... 50

LOCK REGISTER Commands ...................................................................................................................... 50

PASSWORD PROTECTION Commands ....................................................................................................... 50

NONVOLATILE PROTECTION Commands .................................................................................................. 50

NONVOLATILE PROTECTION BIT LOCK BIT Commands ............................................................................ 51

VOLATILE PROTECTION Commands .......................................................................................................... 52

EXTENDED MEMORY BLOCK Commands .................................................................................................. 52

EXIT PROTECTION Command .................................................................................................................... 53

Common Flash Interface ................................................................................................................................ 54

Power-Up and Reset Characteristics ................................................................................................................ 59

Absolute Ratings and Operating Conditions ..................................................................................................... 61

DC Characteristics .......................................................................................................................................... 63

Read AC Characteristics .................................................................................................................................. 65

Write AC Characteristics ................................................................................................................................. 67

Data Polling/Toggle AC Characteristics ............................................................................................................ 72

Program/Erase Characteristics ........................................................................................................................ 74

Package Dimensions ....................................................................................................................................... 75

Revision History ............................................................................................................................................. 77

Rev. H –05/18 ............................................................................................................................................. 77

Rev. G – 11/16 ............................................................................................................................................. 77

Rev. F – 6/16 ............................................................................................................................................... 77

Rev. E – 9/15 ............................................................................................................................................... 77

Rev. D – 01/15 ............................................................................................................................................. 77

Rev. C – 12/14 ............................................................................................................................................. 77

Rev. B – 07/14 ............................................................................................................................................. 77

Rev. A – 05/14 ............................................................................................................................................. 77

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Features

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.

List of Figures

Figure 1: Part Number Chart ............................................................................................................................ 2

Figure 2: Logic Diagram ................................................................................................................................... 9

Figure 3: 56-Pin TSOP (Top View) .................................................................................................................. 10

Figure 4: 64-Ball LBGA (Top View – Balls Down) ............................................................................................. 11

Figure 5: Data Polling Flowchart .................................................................................................................... 19

Figure 6: Toggle Bit Flowchart ........................................................................................................................ 20

Figure 7: Data Polling/Toggle Bit Flowchart .................................................................................................... 21

Figure 8: Lock Register Program Flowchart ..................................................................................................... 25

Figure 9: Boundary Condition of Program Buffer Size ..................................................................................... 35

Figure 10: WRITE TO BUFFER PROGRAM Flowchart ...................................................................................... 36

Figure 11: Software Protection Scheme .......................................................................................................... 45

Figure 12: Set/Clear Nonvolatile Protection Bit Algorithm Flowchart ............................................................... 51

Figure 13: Power-Up Timing .......................................................................................................................... 59

Figure 14: Reset AC Timing – No PROGRAM/ERASE Operation in Progress ...................................................... 60

Figure 15: Reset AC Timing During PROGRAM/ERASE Operation .................................................................... 60

Figure 16: AC Measurement Load Circuit ....................................................................................................... 62

Figure 17: AC Measurement I/O Waveform ..................................................................................................... 62

Figure 18: Random Read AC Timing ............................................................................................................... 66

Figure 19: Page Read AC Timing ..................................................................................................................... 66

Figure 20: WE#-Controlled Program AC Timing .............................................................................................. 68

Figure 21: CE#-Controlled Program AC Timing ............................................................................................... 70

Figure 22: Chip/Block Erase AC Timing .......................................................................................................... 71

Figure 23: Accelerated Program AC Timing ..................................................................................................... 71

Figure 24: Data Polling AC Timing .................................................................................................................. 72

Figure 25: Toggle/Alternative Toggle Bit Polling AC Timing .............................................................................. 73

Figure 26: 56-Pin TSOP – 14mm x 20mm (Package Code: JS) ............................................................................ 75

Figure 27: 64-Ball LBGA – 11mm x 13mm (Package Code: PC) ......................................................................... 76

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Features

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.

List of Tables

Table 1: Signal Descriptions ........................................................................................................................... 12

Table 2: Blocks[1023:0] .................................................................................................................................. 14

Table 3: Bus Operations ................................................................................................................................. 15

Table 4: Data Polling Register Bit Definitions .................................................................................................. 17

Table 5: Operations and Corresponding Bit Settings ........................................................................................ 18

Table 6: Status Register Definitions ................................................................................................................ 22

Table 7: Lock Register Bit Definitions ............................................................................................................. 24

Table 8: Standard Command Definitions – Address-Data Cycles ...................................................................... 26

Table 9: Block Protection ............................................................................................................................... 29

Table 10: Read Electronic Signature – 1Gb ...................................................................................................... 29

Table 11: Command Sequence – Range of Blocks ............................................................................................ 30

Table 12: Command Sequence – Entire Chip .................................................................................................. 32

Table 13: ACCELERATED PROGRAM Requirements and Recommendations .................................................... 38

Table 14: ACCELERATED CHIP ERASE Requirements and Recommendations ................................................. 41

Table 15: VPP/WP# Functions ......................................................................................................................... 43

Table 16: Block Protection Status ................................................................................................................... 46

Table 17: Block Protection Command Definitions – Address-Data Cycles ......................................................... 47

Table 18: Extended Memory Block Address and Data ...................................................................................... 52

Table 19: Query Structure Overview ............................................................................................................... 54

Table 20: CFI Query Identification String ........................................................................................................ 54

Table 21: CFI Query System Interface Information .......................................................................................... 55

Table 22: Device Geometry Definition ............................................................................................................ 55

Table 23: Primary Algorithm-Specific Extended Query Table ........................................................................... 56

Table 24: Power-Up Specifications ................................................................................................................. 59

Table 25: Reset AC Specifications ................................................................................................................... 60

Table 26: Absolute Maximum/Minimum Ratings ............................................................................................ 61

Table 27: Operating Conditions ...................................................................................................................... 61

Table 28: Input/Output Capacitance .............................................................................................................. 62

Table 29: DC Current Characteristics .............................................................................................................. 63

Table 30: DC Voltage Characteristics .............................................................................................................. 64

Table 31: Read AC Characteristics – VCC = VCCQ = 2.7–3.6V ............................................................................... 65

Table 32: Read AC Characteristics – VCCQ = 1.65V–VCC ..................................................................................... 65

Table 33: WE#-Controlled Write AC Characteristics ......................................................................................... 67

Table 34: CE#-Controlled Write AC Characteristics ......................................................................................... 69

Table 35: Data Polling/Toggle AC Characteristics ............................................................................................ 72

Table 36: Program/Erase Characteristics ........................................................................................................ 74

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Features

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.

Important Notes and Warnings

Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document,

including without limitation specifications and product descriptions. This document supersedes and replaces all

information supplied prior to the publication hereof. You may not rely on any information set forth in this docu-

ment if you obtain the product described herein from any unauthorized distributor or other source not authorized

by Micron.

Automotive Applications. Products are not designed or intended for use in automotive applications unless specifi-

cally designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distrib-

utor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims,

costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of

product liability, personal injury, death, or property damage resulting directly or indirectly from any use of non-

automotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and con-

ditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron

products are not designed or intended for use in automotive applications unless specifically designated by Micron

as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to in-

demnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys'

fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage

resulting from any use of non-automotive-grade products in automotive applications.

Critical Applications. Products are not authorized for use in applications in which failure of the Micron compo-

nent could result, directly or indirectly in death, personal injury, or severe property or environmental damage

("Critical Applications"). Customer must protect against death, personal injury, and severe property and environ-

mental damage by incorporating safety design measures into customer's applications to ensure that failure of the

Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron

component for any critical application, customer and distributor shall indemnify and hold harmless Micron and

its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims,

costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of

product liability, personal injury, or death arising in any way out of such critical application, whether or not Mi-

cron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the

Micron product.

Customer Responsibility. Customers are responsible for the design, manufacture, and operation of their systems,

applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAIL-

URE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE

WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR

PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included

in customer's applications and products to eliminate the risk that personal injury, death, or severe property or en-

vironmental damages will result from failure of any semiconductor component.

Limited Warranty. In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential

damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal

or replacement of any products or rework charges) whether or not such damages are based on tort, warranty,

breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly

authorized representative.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Important Notes and Warnings

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.

General Description

The device is an asynchronous, uniform block, parallel NOR Flash memory device.

READ, ERASE, and PROGRAM operations are performed using a single low-voltage sup-

ply. Upon power-up, the device defaults to read array mode.

The main memory array is divided into uniform blocks that can be erased independent-

ly so that valid data can be preserved while old data is purged. PROGRAM and ERASE

commands are written to the command interface of the memory. An on-chip program/

erase controller simplifies the process of programming or erasing the memory by taking

care of all special operations required to update the memory contents. The end of a

PROGRAM or ERASE operation can be detected and any error condition can be identi-

fied. The command set required to control the device is consistent with JEDEC stand-

ards.

CE#, OE#, and WE# control the bus operation of the device and enable a simple con-

nection to most microprocessors, often without additional logic.

The device supports asynchronous random read and page read from all blocks of the

array. It also features an internal program buffer that improves throughput by program-

ming 512 words via one command sequence. A 512-word extended memory block over-

laps addresses with array block 0. Users can program this additional space and then

protect it to permanently secure the contents. The device also features different levels of

hardware and software protection to secure blocks from unwanted modification.

Automatic Power Savings Feature

The automatic power savings feature provides low power operation during reads.

After data is read from the memory array and the address lines are quiescent, the auto-

matic power savings feature reduces device current to a low value of ICCAPS.

During automatic power savings mode, average current is measured over 5ms time in-

terval 5μs after the following events happen:

• No internal read, program or erase activity occurring

• RST# is deasserted and CE# is asserted

• All other signals are quiescent and at VSS or VCCQ

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

General Description

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 2: Logic Diagram

VCC VCCQ

A[MAX:0]

WE#

VPP/WP#

DQ[15:0]

VSS

CE#

OE#

RST#

RY/BY#

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

General Description

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.

Signal Assignments

Figure 3: 56-Pin TSOP (Top View)

A23

A22

A15

A14

A13

A12

A11

A10

A19

A20

WE#

RST#

A21

VPP/WP#

RY/BY#

A18

A17

RFU

A24

A25

A16

DNU

VSS

DQ15

DQ7

DQ14

DQ6

DQ13

DQ5

DQ12

DQ4

VCC

DQ11

DQ3

DQ10

DQ2

DQ9

DQ1

DQ8

DQ0

OE#

VSS

CE#

RFU

VCCQ

Notes: 1. A23 is valid for 256Mb and above; otherwise, it is RFU.

2. A24 is valid for 512Mb and above; otherwise, it is RFU.

3. A25 is valid for 1Gb and above; otherwise, it is RFU.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Signal Assignments

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 4: 64-Ball LBGA (Top View – Balls Down)

VCCQ

CE#

OE#

VSS

A17

DQ0

DQ8

DQ9

DQ1

RY/BY#

A18

A20

DQ2

DQ10

DQ11

DQ3

WE#

VPP

/WP#

RST#

A21

A19

DQ5

DQ12

VCC

DQ4

A10

A11

DQ7

DQ14

DQ13

DQ6

A13

A12

A14

A15

A16

RFU

DQ15

VSS

A22

A23

VCCQ

VSS

A24

A25

Notes: 1. A23 is valid for 256Mb and above; otherwise, it is RFU.

2. A24 is valid for 512Mb and above; otherwise, it is RFU.

3. A25 is valid for 1Gb and above; otherwise, it is RFU.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Signal Assignments

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Signal Descriptions

The signal description table below is a comprehensive list of signals for this device fami-

ly. All signals listed may not be supported on this device. See Signal Assignments for in-

formation specific to this device.

Table 1: Signal Descriptions

Name Type Description

A[MAX:0] Input Address: Selects the cells in the array to access during READ operations. During WRITE oper-

ations, they control the commands sent to the command interface of the program/erase con-

troller.

CE# Input Chip enable: Activates the device, enabling READ and WRITE operations to be performed.

When CE# is HIGH, the device goes to standby and data outputs are High-Z.

OE# Input Output enable: Active LOW input. OE# LOW enables the data output buffers during READ

cycles. When OE# is HIGH, data outputs are High-Z.

WE# Input Write enable: Controls WRITE operations to the device. Address is latched on the falling

edge of WE# and data is latched on the rising edge.

VPP/WP# Input VPP/Write Protect: Provides WRITE PROTECT function and VHH function. These functions

protect the lowest or highest block and enable the device to enter unlock bypass mode, re-

spectively. (Refer to Hardware Protection and Bypass Operations for details.)

RST# Input Reset: Applies a hardware reset to the device control logic and places it in standby, which is

achieved by holding RST# LOW for at least tPLPH. After RST# goes HIGH, the device is ready

for READ and WRITE operations (after tPHEL or tPHWL, whichever occurs last).

DQ[15:0] I/O Data I/O: Outputs the data stored at the selected address during a READ operation. During

WRITE operations, they represent the commands sent to the command interface of the inter-

nal state machine.

RY/BY# Output Ready busy: Open-drain output that can be used to identify when the device is performing

a PROGRAM or ERASE operation. During PROGRAM or ERASE operations, RY/BY# is LOW,

and is High-Z during read mode, auto select mode, and erase suspend mode.

The use of an open-drain output enables the RY/BY# pins from several devices to be connec-

ted to a single pull-up resistor to VCCQ. A low value will then indicate that one (or more) of

the devices is (are) busy. A 10K Ohm or bigger resistor is recommended as pull-up resistor to

achieve 0.1V VOL.

VCC Supply Supply voltage: Provides the power supply for READ, PROGRAM, and ERASE operations.

The device is disabled when VCC ≤ VLKO. If the program/erase controller is programming or

erasing during this time, then the operation aborts and the contents being altered will be

invalid.

A 0.1μF and 0.01µF capacitor should be connected between VCC and VSS to decouple the cur-

rent surges from the power supply. The PCB track widths must be sufficient to carry the cur-

rents required during PROGRAM and ERASE operations (see DC Characteristics).

VCCQ Supply I/O supply voltage: Provides the power supply to the I/O pins and enables all outputs to be

powered independently from VCC.

A 0.1μF and 0.01µF capacitor should be connected between VCCQ and VSS to decouple the

current surges from the power supply.

VSS Supply Ground: All VSS pins must be connected to the system ground.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Signal Descriptions

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 1: Signal Descriptions (Continued)

Name Type Description

RFU — Reserved for future use: Reserved by Micron for future device functionality and enhance-

ment. Recommend that these be left floating. May be connected internally, but external con-

nections will not affect operation.

DNU — Do not use: Do not connect to any other signal, or power supply; must be left floating.

NC — No connect: No internal connection; can be driven or floated.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Signal Descriptions

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Memory Organization

Memory Configuration

The main memory array is divided into 128KB or 64KW uniform blocks.

Memory Map

Table 2: Blocks[1023:0]

Block

Address Range

Start End

1023 3FF 0000h 3FF FFFFh

⋮⋮⋮

511 1FF 0000h 1FF FFFFh

⋮⋮⋮

255 0FF 0000h 0FF FFFFh

⋮⋮⋮

127 07F 0000h 07F FFFFh

⋮⋮⋮

63 03F 0000h 03F FFFFh

⋮⋮⋮

0 000 0000h 000 FFFFh

Note: 1. 1Gb device = Blocks 0–1023.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Memory Organization

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Bus Operations

Table 3: Bus Operations

Notes 1 and 2 apply to entire table

Operation CE# OE# WE# RST# VPP/WP# A[MAX:0] DQ[15:0]

READ L L H H X Address Data output

WRITE L H L H H3Command address Data input4

STANDBY H X X H X X High-Z

OUTPUT

DISABLE

L H H H X X High-Z

RESET X X X L X X High-Z

Notes: 1. Typical glitches of less than 3ns on CE#, OE#, and WE# are ignored by the device and do

not affect bus operations.

2. H = Logic level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW.

3. If WP# is LOW, then the highest or the lowest block remains protected, depending on

line item.

4. Data input is required when issuing a command sequence or when performing data

polling or block protection.

Read

Bus READ operations read from the memory cells, registers, extended memory block, or

CFI space. To accelerate the READ operation, the memory array can be read in page

mode where data is internally read and stored in a page buffer.

Page size is 16 words and is addressed by address inputs A[3:0]. The extended memory

blocks and CFI area support page read mode.

A valid bus READ operation involves setting the desired address on the address inputs,

taking CE# and OE# LOW, and holding WE# HIGH. The data I/Os will output the value.

If CE# goes HIGH and returns LOW for a subsequent access, a random read access is

performed and tACC or tCE is required. (See AC Characteristics for details about when

the output becomes valid.)

Write

Bus WRITE operations write to the command interface. A valid bus WRITE operation

begins by setting the desired address on the address inputs. The address inputs are

latched by the command interface on the falling edge of CE# or WE#, whichever occurs

last. The data I/Os are latched by the command interface on the rising edge of CE# or

WE#, whichever occurs first. OE# must remain HIGH during the entire bus WRITE oper-

ation (See AC Characteristics for timing requirement details).

Standby

Driving CE# HIGH in read mode causes the device to enter standby and data I/Os to be

High-Z (See DC Characteristics).

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Bus Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.

During PROGRAM or ERASE operations, the device will continue to use the program/

erase supply current (ICC3) until the operation completes. The device cannot be placed

into standby mode during a PROGRAM/ERASE operation.

Output Disable

Data I/Os are High-Z when OE# is HIGH.

Reset

During reset mode the device is deselected and the outputs are High-Z. The device is in

reset mode when RST# is LOW. The power consumption is reduced to the standby level,

independently from CE#, OE#, or WE# inputs.

When RST# is HIGH, a time of tPHEL is required before a READ operation can access

the device, and a delay of tPHWL is required before a write sequence can be initiated.

After this wake-up interval, normal operation is restored, the device defaults to read ar-

ray mode, and the data polling register is reset.

If RST# is driven LOW during a PROGRAM/ERASE operation or any other operation that

requires writing to the device, the operation will abort within tPLRH, and memory con-

tents at the aborted block or address are no longer valid.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Bus Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Registers

The device features two methods for monitoring internal status during modify opera-

tions: data polling status and read status register. Users must not mix the two methods.

Only one method at a time must be used to monitor internal operations.

Data Polling Register

The device automatically enters data polling status mode upon command issuance.

The data polling status information uses the following to indicate information: DQ1,

DQ2, DQ3, DQ5, DQ6, and DQ7; DQ[15:8] are reserved and will output 00h.

Table 4: Data Polling Register Bit Definitions

Note 1 applies to entire table

Bit Name Settings Description Notes

DQ7 Data polling

bit

0 or 1, depending on

operations

Monitors whether the program/erase controller has successful-

ly completed its operation, or has responded to an ERASE SUS-

PEND operation.

2, 4

DQ6 Toggle bit Toggles: 0 to 1; 1 to 0;

and so on

Monitors whether the program, erase, or blank check control-

ler has successfully completed its operations, or has responded

to an ERASE SUSPEND operation. During a PROGRAM/ERASE/

BLANK CHECK operation, DQ6 toggles from 0 to 1, 1 to 0, and

so on, with each successive READ operation from any address.

3, 4, 5

DQ5 Error bit 0 = Success

1 = Failure

Identifies errors detected by the program/erase controller. DQ5

is set to 1 when a PROGRAM, BLOCK ERASE, or CHIP ERASE op-

eration fails to write the correct data to the memory, or when

a BLANK CHECK or CRC operation fails.

4, 6

DQ3 Erase timer

bit

0 = Erase not in progress

1 = Erase in progress

Identifies the start of program/erase controller operation dur-

ing a BLOCK ERASE command. Before the program/erase con-

troller starts, this bit set to 0.

DQ2 Alternative

toggle bit

Toggles: 0 to 1; 1 to 0;

and so on

During CHIP ERASE, BLOCK ERASE, and ERASE SUSPEND opera-

tions, DQ2 toggles from 0 to 1, 1 to 0, and so on, with each

successive READ operation from addresses within the blocks

being erased.

3, 4

DQ1 Buffered

program

abort bit

1 = Abort Indicates a BUFFER PROGRAM, BLANK CHECK, or CRC opera-

tion abort. The BUFFERED PROGRAM ABORT and RESET com-

mand must be issued to return the device to read mode (see

WRITE TO BUFFER PROGRAM command).

Notes: 1. The data polling register can be read during PROGRAM, ERASE, or ERASE SUSPEND op-

erations; the READ operation outputs data on DQ[7:0].

2. For a PROGRAM operation in progress, DQ7 outputs the complement of the bit being

programmed. For a READ operation from the address previously programmed success-

fully, DQ7 outputs existing DQ7 data. For a READ operation from addresses with blocks

to be erased while an ERASE SUSPEND operation is in progress, DQ7 outputs 0; upon

successful completion of the ERASE SUSPEND operation, DQ7 outputs 1. For an ERASE

operation in progress, DQ7 outputs 0; upon ERASE operation's successful completion,

DQ7 outputs 1. During a BUFFER PROGRAM operation, the data polling bit is valid only

for the last word being programmed in the write buffer.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.

3. After successful completion of a PROGRAM, ERASE, or BLANK CHECK operation, the de-

vice returns to read mode.

4. During erase suspend mode, READ operations to addresses within blocks not being

erased output memory array data as if in read mode. A protected block is treated the

same as a block not being erased. See the Toggle Flowchart for more information.

5. During erase suspend mode, DQ6 toggles when addressing a cell within a block being

erased. The toggling stops when the program/erase controller has suspended the ERASE

operation. See the Toggle Flowchart for more information.

6. When DQ5 is set to 1, a READ/RESET (F0h) command must be issued before any subse-

quent command.

Table 5: Operations and Corresponding Bit Settings

Note 1 applies to entire table

Operation Address DQ7 DQ6 DQ5 DQ3 DQ2 DQ1 RY/BY# Notes

PROGRAM Any address DQ7# Toggle 0 – – 0 0 2

CRC range of

blocks

Any address 1 Toggle 0 – – 0 0

CRC chip Any address DQ7# Toggle 0 – – 0 0 4

CHIP ERASE Any address 0 Toggle 0 1 Toggle – 0

BLANK CHECK Blank-checking

block

0 Toggle 0 1 Toggle – 0

Non-blank-check-

ing block

0 Toggle 0 1 No toggle – 0

BLOCK ERASE Erasing block 0 Toggle 0 1 Toggle – 0

Non-erasing block 0 Toggle 0 1 No toggle – 0

PROGRAM

SUSPEND

Programming

block

Invalid operation High-Z

Nonprogramming

block

Outputs memory array data as if in read mode High-Z

ERASE

SUSPEND

Erasing block 1 No Toggle 0 – Toggle – High-Z

Non-erasing block Outputs memory array data as if in read mode High-Z

PROGRAM during

ERASE SUSPEND

Erasing block DQ7# Toggle 0 – Toggle – 0 2

Non-erasing block DQ7# Toggle 0 – No Toggle – 0 2

BUFFERED

PROGRAM ABORT

Any address DQ7# Toggle 0 – – 1 High-Z

PROGRAM Error Any address DQ7# Toggle 1 – – – High-Z 2

ERASE Error Any address 0 Toggle 1 1 Toggle – High-Z

BLANK CHECK Er-

ror

Any address 0 Toggle 1 1 Toggle – High-Z

CRC range of

blocks error

Any address 1 Toggle 1 – – – High-Z

CRC chip error Any address DQ7# Toggle 1 – – – High-Z 4

Notes: 1. Unspecified data bits should be ignored.

2. DQ7# for buffer program is related to the last address location loaded.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.

3. DQ7# is the reverse DQ7 of the last word or byte loaded before CRC chip confirm com-

mand cycle.

Figure 5: Data Polling Flowchart

Start

DQ7 = Data

DQ5 = 1

DQ1 = 1

DQ7 = Data

Yes

Read DQ7, DQ5, and DQ1

at valid address1

Read DQ7 at valid address

SuccessFailure

Notes: 1. Valid address is the last address being programmed or an address within the block being

erased.

2. Failure results: DQ5 = 1 indicates an operation error. A READ/RESET (F0h) command must

be issued before any subsequent command.

3. Failure results: DQ1 = 1 indicates a WRITE TO BUFFER PROGRAM ABORT operation. A

full three-cycle RESET (AAh/55h/F0h) command sequence must be used to reset the abor-

ted device.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 6: Toggle Bit Flowchart

DQ6 = Toggle

DQ5 = 1

DQ6 = Toggle

Yes

Start

Read DQ6 at valid address

Read DQ6, DQ5, and DQ1

at valid address

Read DQ6 (twice) at valid address

SuccessFailure1

DQ1 = 1

Yes

Note: 1. Failure results: DQ5 = 1 indicates an operation error; DQ1 = 1 indicates a WRITE TO BUF-

FER PROGRAM ABORT operation.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 7: Data Polling/Toggle Bit Flowchart

WRITE TO BUFFER

PROGRAM

Start

DQ7 = Valid data

DQ5 = 1

Yes

DQ6 = Toggling Yes

No No

Yes

PROGRAM operation

DQ6 = Toggling

DQ2 = Toggling

Yes

DQ1 = 1

Read 3 correct data?

Yes

Device busy: Repolling

PROGRAM operation

complete

PROGRAM operation

failure

WRITE TO BUFFER

PROGRAM

abort

Timeout failure

ERASE operation

complete

Erase/suspend mode

Device error

Read2.DQ6 = Read3.DQ6

Read2.DQ2 = Read3.DQ2

Read1.DQ6 = Read2.DQ6

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Read Status Register

The device’s status register displays PROGRAM, ERASE, and BLANK CHECK operations

status. A device’s status can be read after writing the READ STATUS REGISTER com-

mand (70h). When the READ STATUS REGISTER command is issued, the current status

is captured by the register and the device is in read status register mode. The first read

access in the status register mode exits the mode and returns to the output state when

the READ STATUS REGISTER command was issued. No other command should be sent

before reading the status register to exit the status register mode.

The status register bits are output on DQ[7:0], while DQ[15:8] outputs are 00h.

Table 6: Status Register Definitions

Bit Name Settings Description

SR[15:8] – Reserved Reserved for future use. Will always be set to 0.

SR7 Device program/

erase/blank check

status

0 = Busy

1 = Ready

Indicates erase, program, or blank check completion in the de-

vice. SR[6:1] are invalid; SR7 = 0.

SR6 Erase suspend status 0 = Erase in progress/

complete

1 = Erase suspended

Indicates whether the device is erase suspended. After issuing an

ERASE SUSPEND command, SR7 and SR6 are set to 1. SR6 remains

set until the device receives an ERASE RESUME command.

SR5 Erase/blank check

status

0 = Erase/blank

check successful

1 = Erase/blank

check error

Set to 1 if an attempted erase or blank check failed.

SR4 Program status 0 = Program success

1 = Program error

Indicates whether the program failed or the buffer program has

aborted.

SR3 Writer buffer abort

status

0 = Program not

aborted

1 = Program aborted

during buffer pro-

gram

Indicates whether the buffer program has aborted.

SR2 Program suspend

status

0 = Program in pro-

gress/complete

1 = Program suspen-

ded

Indicates whether the device is program suspended. After receiv-

ing a PROGRAM SUSPEND command, SR7 and SR2 are set to 1,

and remain set at 1 until a RESUME command is received.

SR1 Device protect status 0 = Unlocked

1 = Aborted erase/

program attempt on

a locked block

Indicates whether program or erase was attempted on a locked

block. If an ERASE or PROGRAM operation is attempted on a

locked block, SR1 is set to 1 and the operation aborts.

SR0 – Reserved Reserved for future use. Will always be set to 0.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Clear Status Register

The status register content can be cleared by CLEAR STATUS REGISTER command

(71h). The CLEAR STATUS REGISTER command clears the status register bits SR[6:1].

SR7 remains at 0, which indicates the device is busy.

However, for buffer program abort only, the CLEAR STATUS REGISTER command

would change also SR7 to 1, which reverts the device to main array read mode. The sta-

tus register can also be cleared by using RESET Command (F0h).

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Lock Register

Table 7: Lock Register Bit Definitions

Note 1 applies to entire table

Bit Name Settings Description Notes

DQ[15:9] – Default value = 1 DQ[15:9] are reserved and are set to a default value of 1.

DQ8 – Default value = 0 DQ8 is reserved and is set to a default value of 0.

DQ[7:3] – Default value =1 DQ[7:3] are reserved and are set to a default value of 1.

DQ2 Password pro-

tection mode

lock bit

0 = Password protec-

tion mode enabled

1 = Password protec-

tion mode disabled

(default)

Places the device permanently in password protection mode. 2

DQ1 Nonvolatile

protection

mode lock bit

0 = Nonvolatile pro-

tection mode enabled

with password protec-

tion mode perma-

nently disabled

1 = Nonvolatile pro-

tection mode enabled

(default)

Places the device in nonvolatile protection mode, with pass-

word protection mode permanently disabled. When shipped

from the factory, the device will operate in nonvolatile pro-

tection mode, and the memory blocks are unprotected.

DQ0 Extended

memory

block protec-

tion bit

0 = Protected

1 = Unprotected (de-

fault)

If the device is shipped with the extended memory block un-

locked, the block can be protected by setting this bit to 0. The

extended memory block protection status can be read in auto

select mode by issuing an AUTO SELECT command.

Notes: 1. The lock register is a 16-bit, one-time programmable register. DQ[15:3] are reserved.

2. The password protection mode lock bit and nonvolatile protection mode lock bit cannot

both be programmed to 0. Any attempt to program one while the other is programmed

causes the operation to abort, and the device returns to read mode. The device is ship-

ped from the factory with the default setting.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 8: Lock Register Program Flowchart

Start

Success: EXIT PROTECTION

command set

Address/data cycle 1

Address/data cycle 2

Done?

Match expected

value, 0?

Yes

Enter LOCK REGISTER command set

Address/data (unlock) cycle 1

Address/data (unlock) cycle 2

Address/data cycle 3

PROGRAM LOCK REGISTER

Address/data cycle 1

Address/data cycle 2

Polling algorithm

Read lock register

Notes: 1. Each lock register bit can be programmed only once.

2. See the Block Protection Command Definitions table for address-data cycle details.

3. DQ5 and DQ1 are ignored in this algorithm flow.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Registers

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Standard Command Definitions – Address-Data Cycles

Table 8: Standard Command Definitions – Address-Data Cycles

Note 1 applies to entire table

Command and

Code/Subcode

Address and Data Cycles

Notes

1st 2nd 3rd 4th 5th 6th

A D A D A D A D A D A D

READ and AUTO SELECT Operations

READ/RESET (F0h) 555 AA 2AA 55 X F0 2

READ CFI (98h) 555 98

EXIT READ CFI (F0h) X F0

AUTO SELECT (90h) 555 AA 2AA 55 555 90 Note 3 Note 3 4, 5

EXIT AUTO SELECT (F0h) X F0

READ STATUS (70h) 555 70

CLEAR STATUS (71h) 555 71

BYPASS Operations

UNLOCK BYPASS (20h) 555 AA 2AA 55 555 20

UNLOCK BYPASS

RESET (90h/00h)

X 90 X 00

PROGRAM Operations

PROGRAM (A0h) 555 AA 2AA 55 555 A0 PA PD

UNLOCK BYPASS

PROGRAM (A0h)

X A0 PA PD 6

WRITE TO BUFFER

PROGRAM (25h)

555 AA 2AA 55 BAd 25 BAd N PA PD 7, 8, 9

UNLOCK BYPASS

WRITE TO BUFFER

PROGRAM (25h)

BAd 25 BAd N PA PD 6

WRITE TO BUFFER

PROGRAM CONFIRM

(29h)

BAd 29 7

BUFFERED PROGRAM

ABORT and RESET (F0h)

555 AA 2AA 55 555 F0

PROGRAM SUSPEND

(B0h)

X B0

PROGRAM RESUME (30h) X 30

PROGRAM SUSPEND

(51h)

X 51

PROGRAM RESUME (50h) X 50

ERASE Operations

CHIP ERASE (80/10h) 555 AA 2AA 55 555 80 555 AA 2AA 55 555 10

UNLOCK BYPASS

CHIP ERASE (80/10h)

X 80 X 10 6

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Standard Command Definitions – Address-Data Cycles

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 8: Standard Command Definitions – Address-Data Cycles (Continued)

Note 1 applies to entire table

Command and

Code/Subcode

Address and Data Cycles

Notes

1st 2nd 3rd 4th 5th 6th

A D A D A D A D A D A D

BLOCK ERASE (80/30h) 555 AA 2AA 55 555 80 555 AA 2AA 55 BAd 30

UNLOCK BYPASS

BLOCK ERASE (80/30h)

X 80 BAd 30 6

ERASE SUSPEND (B0h) X B0

ERASE RESUME (30h) X 30

BLANK CHECK Operations

BLANK CHECK 555 33

Notes: 1. A = Address; D = Data; X = "Don't Care"; BAd = Any address in the block; N = Number of

words to be programmed; PA = Program address; PD = Program data; Gray shading =

Not applicable. All values in the table are hexadecimal. Some commands require both a

command code and subcode.

2. A full three-cycle RESET command sequence must be used to reset the device in the

event of a buffered program abort error (DQ1 = 1).

3. These cells represent READ cycles (versus WRITE cycles for the others).

4. AUTO SELECT enables the device to read the manufacturer code, device code, block pro-

tection status, and extended memory block protection indicator.

5. AUTO SELECT addresses and data are specified in the Electronic Signature table and the

Extended Memory Block Protection table.

6. For any UNLOCK BYPASS ERASE/PROGRAM command, the first two UNLOCK cycles are

unnecessary.

7. BAd must be the same as the address loaded during the WRITE TO BUFFER PROGRAM

3rd and 4th cycles.

8. WRITE TO BUFFER PROGRAM operation: maximum cycles = 517. UNLOCK BYPASS WRITE

TO BUFFER PROGRAM operation: maximum cycles = 515. WRITE TO BUFFER PROGRAM

operation: N + 1 = words to be programmed; maximum buffer size = 512 words.

9. A[MAX:9] address pins should remain unchanged while A[8:0] pins are used to select a

word within the N+1 word page.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Standard Command Definitions – Address-Data Cycles

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice.

READ and AUTO SELECT Operations

READ/RESET Command

The READ/RESET (F0h) command returns the device to read mode and resets the errors

in the data polling register. One or three bus WRITE operations can be used to issue the

READ/RESET command. Note: A full three-cycle RESET command sequence must be

used to reset the device in the event of a buffered program abort error (DQ1 = 1).

Once a PROGRAM, ERASE, or SUSPEND operation begins, RESET commands are ignor-

ed until the operation is complete. Read/reset serves primarily to return the device to

read mode from a failed PROGRAM or ERASE operation. Read/reset may cause a return

to read mode from undefined states that might result from invalid command sequen-

ces. A hardware reset may be required to return to normal operation from some unde-

fined states.

To exit the unlock bypass mode, the system must issue a two-cycle UNLOCK BYPASS

RESET command sequence. A READ/RESET command will not exit unlock bypass

mode.

READ CFI Command

The READ CFI (98h) command puts the device in read CFI mode and is only valid when

the device is in read array or auto select mode. One bus WRITE cycle is required to issue

the command.

Once in read CFI mode, bus READ operations will output data from the CFI memory

area (Refer to the Common Flash Interface for details).

Read CFI mode is exited by performing a READ/RESET command (F0h). The device re-

turns to read mode unless it entered read CFI mode after an ERASE SUSPEND or PRO-

GRAM SUSPEND command, in which case it returns to erase or program suspend

mode.

AUTO SELECT Command

At power-up or after a hardware reset, the device is in read mode. It can then be put in

auto select mode by issuing an AUTO SELECT (90h) command. Auto select mode ena-

bles the following device information to be read:

• Electronic signature, which includes manufacturer and device code information as

shown in the Electronic Signature table.

• Block protection, which includes the block protection status and extended memory

block protection indicator, as shown in the Block Protection table.

Electronic signature or block protection information is read by executing a READ opera-

tion with control signals and addresses set, as shown in the Read Electronic Signature

table or the Block Protection table, respectively. In addition, this device information can

be read or set by issuing an AUTO SELECT command.

Auto select mode can be used by the programming equipment to automatically match a

device with the application code to be programmed.

Three consecutive bus WRITE operations are required to issue an AUTO SELECT com-

mand. The device remains in auto select mode until a READ/RESET or READ CFI com-

mand is issued.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

READ and AUTO SELECT Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The device cannot enter auto select mode when a PROGRAM or ERASE operation is in

progress (RY/BY# LOW). However, auto select mode can be entered if the PROGRAM or

ERASE operation has been suspended by issuing a PROGRAM SUSPEND or ERASE SUS-

PEND command.

Auto select mode is exited by performing a READ/RESET command (F0h). The device

returns to read mode unless it entered auto select mode after an ERASE SUSPEND or

PROGRAM SUSPEND command, in which case it returns to erase or program suspend

mode.

Table 9: Block Protection

Note 1 applies to entire table

READ Cycle CE# OE# WE#

Address Input Data Input/Output

A[MAX:16] A[15:2] A1 A0 DQ[15:0]

128-bit (0x0~0x7) Factory-Programmable Extended Memory Protection Indicator (Bit DQ7)

Low lock L L H L L H H 0009h2

0089h3

High lock L L H L L H H 0019h2

0099h3

Block protection status

Protected L L H Block base

address

L H L 0001h

Unprotected L L H L H L 0000h

Notes: 1. H = Logic level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW.

2. Customer-lockable (default).

3. Micron prelocked.

Read Electronic Signature

Table 10: Read Electronic Signature – 1Gb

Note 1 applies to entire table

READ Cycle CE# OE# WE#

Address Input

Data Input/

Output

A[MAX:4] A3 A2 A1 A0 DQ[15:0]

Manufacturer code L L H L L L L L 0089h

Device code 1 L L H L L L L H 227Eh

Device code 2 L L H L H H H L 2228h

Device code 3 L L H L H H H H 2201h

Note: 1. H = Logic level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

READ and AUTO SELECT Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Cyclic Redundancy Check Operation

CYCLIC REDUNDANCY CHECK Command

The CYCLIC REDUNDANCY CHECK (CRC) command is a nonsecure hash function de-

signed to detect accidental changes to raw data. Typically, it is used in digital networks

and storage devices such as hard disk drives. A CRC-enabled device calculates a short,

fixed-length binary sequence known as the CRC code (or CRC). The device CRC opera-

tion will generate the CRC result of the whole device or of an address range specified by

the operation. Then the CRC result is compared with the expected CRC data provided in

the sequence. Finally, the device indicates a pass or fail through the data polling regis-

ter. If the CRC fails, corrective action is possible, such as re-verifying with a normal

READ mode or rewriting the array data.

CRC is a higher performance alternative to reading data directly to verify recently pro-

grammed data, or as a way to periodically check the data integrity of a large block of

data against a stored CRC reference over the life of the product.

CRC helps improve test efficiency for programmer or burn-in stress tests. No system

hardware changes are required to enable CRC.

The CRC-64 operation follows the ECMA standard; the generating polynomial is:

G(x) = x64 + x62 + x57 + x55 + x54 + x53 + x52 + x47 + x46 + x45 + x40 + x39 + x38 + x37 + x35 + x33

+ x32+ x31 + x29 + x27 + x24 + x23 + x22 + x21 + x19 + x17 + x13 + x12 + x10 + x9 + x7 + x4 + x + 1

Note: The data stream sequence is from LSB to MSB and the default initial CRC value is

all zeros.

The CRC command sequences are shown in the tables below, for an entire die or for a

selected range, respectively.

Cyclic Redundancy Check Operation Command Sequence

Table 11: Command Sequence – Range of Blocks

Note 1 and 2 apply to entire table.

Address DQ[15:0] Description Notes

0000555 00AAh UI unlock cycle 1

00002AA 0055h UI unlock cycle 2

0000000 00EBh Extended function interface command

0000000 0027h CRC sub-op code

0000000 000Ah N-1 data count

0000000 FFFEh CRC operation option data

0000001 Data 1st word of 64-bit expected CRC

0000002 Data 2nd word of 64-bit expected CRC

0000003 Data 3rd word of 64-bit expected CRC

0000004 Data 4th word of 64-bit expected CRC

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Cyclic Redundancy Check Operation

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 11: Command Sequence – Range of Blocks (Continued)

Note 1 and 2 apply to entire table.

Address DQ[15:0] Description Notes

0000005 DQ15 = A14

DQ14 = A13

...

DQ2 = A1

DQ1 = A0

DQ0 = set to zero

Byte address to start 3

0000006 A30-A15 Byte address to start 3

0000007 Reserved Default as 0000h

0000008 DQ15 = A14

DQ14 = A13

...

DQ2 = A1

DQ1 = A0

DQ0 = set to zero

Byte address to stop 3

0000009 A30-A15 Byte address to stop 3

000000A Reserved Default as 0000h

0000000 0029h Confirm command

0000000 Read Continue data polling to wait for device to be ready

Notes: 1. If the CRC check fails, a check error is generated by setting DQ5 = 1.

2. This is a byte-aligned operation.

3. The stop address must be bigger than the start address; otherwise, the algorithm will

take no action.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Cyclic Redundancy Check Operation

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 12: Command Sequence – Entire Chip

Address DQ[15:0] Description

0000555 00AAh UI unlock cycle 1

00002AA 0055h UI unlock cycle 2

0000000 00EBh Extended function interface command

0000000 0027h CRC sub-op code

0000000 0004h N-1 data count

0000000 FFFFh CRC operation option data

0000001 Data 1st word of 64-bit expected CRC

0000002 Data 2nd word of 64-bit expected CRC

0000003 Data 3rd word of 64-bit expected CRC

0000004 Data 4th word of 64-bit expected CRC

0000000 0029h Confirm command

0000000 Read Continue data polling to wait for device to be ready

Note: 1. Applies to entire table: If the CRC check fails, a check error is generated by setting DQ5

= 1.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Cyclic Redundancy Check Operation

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Bypass Operations

UNLOCK BYPASS Command

The UNLOCK BYPASS (20h) command is used to place the device in unlock bypass

mode. Three bus WRITE operations are required to issue the UNLOCK BYPASS com-

mand.

When the device enters unlock bypass mode, the two initial UNLOCK cycles required

for a standard PROGRAM or ERASE operation are not needed, thus enabling faster total

program or erase time.

The UNLOCK BYPASS command is used in conjunction with UNLOCK BYPASS PRO-

GRAM or UNLOCK BYPASS ERASE commands to program or erase the device faster

than with standard PROGRAM or ERASE commands. Using these commands can save

considerable time when the cycle time to the device is long. When in unlock bypass

mode, only the following commands are valid:

• The UNLOCK BYPASS PROGRAM command can be issued to program addresses

within the device.

• The UNLOCK BYPASS BLOCK ERASE command can then be issued to erase one or

more memory blocks.

• The UNLOCK BYPASS CHIP ERASE command can be issued to erase the whole mem-

ory array.

• The UNLOCK BYPASS WRITE TO BUFFER PROGRAM and UNLOCK BYPASS EN-

HANCED WRITE TO BUFFER PROGRAM commands can be issued to speed up the

programming operation.

• The UNLOCK BYPASS RESET command can be issued to return the device to read

mode.

In unlock bypass mode, the device can be read as if in read mode.

In addition to the UNLOCK BYPASS command, when VPP/WP# is raised to VHH, the de-

vice automatically enters unlock bypass mode. When V PP/WP# returns to VIH or VIL, the

device is no longer in unlock bypass mode, and normal operation resumes. The transi-

tions from VIH to VHH and from VHH to VIH must be slower than tVHVPP. (See the Accel-

erated Program, Data Polling/Toggle AC Characteristics.)

Note: Micron recommends entering and exiting unlock bypass mode using the ENTER

UNLOCK BYPASS and UNLOCK BYPASS RESET commands rather than raising VPP/WP#

to VHH. VPP/WP# should never be raised to VPPH from any mode except read mode; oth-

erwise, the device may be left in an indeterminate state. VPP/WP# should not remain at

VHH for than 80 hours cumulative.

UNLOCK BYPASS RESET Command

The UNLOCK BYPASS RESET (90/00h) command is used to return to read/reset mode

from unlock bypass mode. Two bus WRITE operations are required to issue the UN-

LOCK BYPASS RESET command. The READ/RESET command does not exit from un-

lock bypass mode.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Bypass Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Program Operations

PROGRAM Command

The PROGRAM (A0h) command can be used to program a value to one address in the

memory array. The command requires four bus WRITE operations, and the final WRITE

operation latches the address and data in the internal state machine and starts the pro-

gram/erase controller. After programming has started, bus READ operations output the

data polling register content.

Programming can be suspended and then resumed by issuing a PROGRAM SUSPEND

command and a PROGRAM RESUME command, respectively.

If the address falls in a protected block, the PROGRAM command is ignored, and the

data remains unchanged. The data polling register is not read, and no error condition is

given.

After the PROGRAM operation has completed, the device returns to read mode, unless

an error has occurred. When an error occurs, bus READ operations to the device contin-

ue to output the data polling register. A READ/RESET command must be issued to reset

the error condition and return the device to read mode.

The PROGRAM command cannot change a bit set to 0 back to 1, and an attempt to do

so is masked during a PROGRAM operation. Instead, an ERASE command must be used

to set all bits in one memory block or in the entire memory from 0 to 1.

The PROGRAM operation is aborted by performing a hardware reset or by powering

down the device. In this case, data integrity cannot be ensured, and it is recommended

that the words or bytes that were aborted be reprogrammed.

UNLOCK BYPASS PROGRAM Command

When the device is in unlock bypass mode, the UNLOCK BYPASS PROGRAM (A0h)

command can be used to program one address in the memory array. The command re-

quires two bus WRITE operations instead of four required by a standard PROGRAM

command; the final WRITE operation latches the address and data and starts the pro-

gram/erase controller (The standard PROGRAM command requires four bus WRITE op-

erations). The PROGRAM operation using the UNLOCK BYPASS PROGRAM command

behaves identically to the PROGRAM operation using the PROGRAM command. The

operation cannot be aborted. A bus READ operation to the memory outputs the data

polling register.

WRITE TO BUFFER PROGRAM Command

The WRITE TO BUFFER PROGRAM (25h) command makes use of the program buffer to

speed up programming and dramatically reduces system programming time compared

to the standard non-buffered PROGRAM command. This product supports a 512-word

maximum program buffer.

When issuing a WRITE TO BUFFER PROGRAM command, V PP/WP# can be held HIGH

or raised to VHH. Also, it can be held LOW if the block is not the lowest or highest block,

depending on the part number.

The following successive steps are required to issue the WRITE TO BUFFER PROGRAM

command:

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Program Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice.

First, two UNLOCK cycles are issued. Next, a third bus WRITE cycle sets up the WRITE

TO BUFFER PROGRAM command. The set-up code can be addressed to any location

within the targeted block. Then, a fourth bus WRITE cycle sets up the number of words

to be programmed. Value n is written to the same block address, where n + 1 is the

number of words to be programmed. Value n + 1 must not exceed the size of the pro-

gram buffer, or the operation will abort. A fifth cycle loads the first address and data to

be programmed. Last, n bus WRITE cycles load the address and data for each word into

the program buffer. Addresses must lie within the range from the start address +1 to the

start address + (n - 1).

Optimum programming performance and lower power usage are achieved by aligning

the starting address at the beginning of a 512-word boundary (A[8:0] = 0x000h). Any

buffer size smaller than 512 words is allowed within a 512-word boundary, while all ad-

dresses used in the operation must lie within the 512-word boundary. In addition, any

crossing boundary buffer program will result in a program abort.

To program the content of the program buffer, this command must be followed by a

WRITE TO BUFFER PROGRAM CONFIRM command.

If an address is written several times during a WRITE TO BUFFER PROGRAM operation,

the address/data counter will be decremented at each data load operation, and the data

will be programmed to the last word loaded into the buffer.

Invalid address combinations or the incorrect sequence of bus WRITE cycles will abort

the WRITE TO BUFFER PROGRAM command.

The data polling register bits DQ1, DQ5, DQ6, DQ7 can be used to monitor the device

status during a WRITE TO BUFFER PROGRAM operation.

The WRITE TO BUFFER PROGRAM command should not be used to change a bit set to

0 back to 1, and an attempt to do so is masked during the operation. Rather than the

WRITE TO BUFFER PROGRAM command, the ERASE command should be used to set

memory bits from 0 to 1.

Figure 9: Boundary Condition of Program Buffer Size

0400h

0000h

512 Words

0200h

511 words or less are allowed

in the program buffer

512-word program

buffer is allowed

Any buffer program attempt

is not allowed

512-word program

buffer is allowed

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Program Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 35 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 10: WRITE TO BUFFER PROGRAM Flowchart

Abort

WRITE TO BUFFER

Write buffer data,

start address

Start

X = n

Write n,1

block address

Write to a different

block address

X = 0

Write next data,2

program address pair

WRITE TO BUFFER

confirm, block address

X = X - 1

Yes

Polling

status = done?

Yes

Error?

Yes

WRITE TO BUFFER

command,

block address

Perform polling

algorithm

Buffer program

abort?

Failure: Issue RESET

command to return to

read array mode

Success: Return to

read array mode

Failure: Issue BUFFERED

PROGRAM ABORT AND

RESET command

First three cycles of the

WRITE TO BUFFER

PROGRAM command

Notes: 1. n + 1 is the number of addresses to be programmed.

2. The BUFFERED PROGRAM ABORT AND RESET command (3 cycles reset) must be issued to

return the device to read mode.

3. When the block address is specified, any address in the selected block address space is

acceptable. However, when loading program buffer address with data, all addresses

must fall within the selected program buffer page.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Program Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 36 Micron Technology, Inc. reserves the right to change products or specifications without notice.

UNLOCK BYPASS WRITE TO BUFFER PROGRAM Command

When the device is in unlock bypass mode, the UNLOCK BYPASS WRITE TO BUFFER

(25h) command can be used to program the device in fast program mode. The com-

mand requires two bus WRITE operations fewer than the standard WRITE TO BUFFER

PROGRAM command.

The UNLOCK BYPASS WRITE TO BUFFER PROGRAM command behaves the same way

as the WRITE TO BUFFER PROGRAM command: the operation cannot be aborted, and

a bus READ operation to the memory outputs the data polling register.

The WRITE TO BUFFER PROGRAM CONFIRM command is used to confirm an UN-

LOCK BYPASS WRITE TO BUFFER PROGRAM command and to program the n + 1

words loaded in the program buffer by this command.

WRITE TO BUFFER PROGRAM CONFIRM Command

The WRITE TO BUFFER PROGRAM CONFIRM (29h) command is used to confirm a

WRITE TO BUFFER PROGRAM command and to program the n + 1 words loaded in the

program buffer by this command.

BUFFERED PROGRAM ABORT AND RESET Command

A BUFFERED PROGRAM ABORT AND RESET (F0h) command must be issued to reset

the device to read mode when the BUFFER PROGRAM operation is aborted. The buffer

programming sequence can be aborted in the following ways:

• Load a value that is greater than the page buffer size during the number of locations

to program in the WRITE TO BUFFER PROGRAM command.

• Write to an address in a different block than the one specified during the WRITE BUF-

FER LOAD command.

• Write an address/data pair to a different write buffer page than the one selected by

the starting address during the program buffer data loading stage of the operation.

• Write data other than the CONFIRM command after the specified number of data

load cycles.

The abort condition is indicated by DQ1 = 1, DQ7 = DQ7# (for the last address location

loaded), DQ6 = toggle, and DQ5 = 0 (all of which are data polling register bits). A BUF-

FERED PROGRAM ABORT and RESET command sequence must be written to reset the

device for the next operation.

Note: The full three-cycle BUFFERED PROGRAM ABORT and RESET command se-

quence is required when using buffer programming features in unlock bypass mode.

PROGRAM SUSPEND Command

The PROGRAM SUSPEND command can be used to interrupt a program operation so

that data can be read from another block. When the PROGRAM SUSPEND command is

issued during a program operation, the device suspends the operation within the pro-

gram suspend latency time and updates the data polling register bits.

After the PROGRAM operation has been suspended, data can be read from any address.

However, data is invalid when read from an address where a program operation has

been suspended.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Program Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 37 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The PROGRAM SUSPEND command may also be issued during a PROGRAM operation

while an erase is suspended. In this case, data may be read from any address not in

erase suspend or program suspend mode. To read from the extended memory block

area (one-time programmable area), the ENTER/EXIT EXTENDED MEMORY BLOCK

command sequences must be issued.

The system may also issue the AUTO SELECT command sequence when the device is in

program suspend mode. The system can read as many auto select codes as required.

When the device exits auto select mode, the device reverts to program suspend mode

and is ready for another valid operation.

The PROGRAM SUSPEND operation is aborted by performing a device reset or power-

down. In this case, data integrity cannot be ensured, and it is recommended that the

words that were aborted be reprogrammed. This device has two different command co-

des for program suspend, B0h and 51h. Code B0h is available for legacy compatibility.

Code 51h is recommended for use.

PROGRAM RESUME Command

The PROGRAM RESUME command must be issued to exit a program suspend mode

and resume a PROGRAM operation. The controller can use DQ7 or DQ6 data polling

bits to determine the status of the PROGRAM operation. After a PROGRAM RESUME

command is issued, subsequent PROGRAM RESUME commands are ignored. Another

PROGRAM SUSPEND command can be issued after the device has resumed program-

ming. This device has two different command codes for Program Resume (30h or 50h).

Code 30h is available for legacy compatibility. Code 50h is recommended to use.

ACCELERATED BUFFERED PROGRAM Operations

ACCELERATED BUFFER PROGRAM operations provides faster performance than

standard program command sequences. Operations are enabled through VPP/WP# un-

der the VHH voltage supply.

When the system asserts VHH on input, the device automatically enters the UNLOCK

BYPASS mode, which enables the system to use the UNLOCK BYPASS WRITE TO BUF-

FER PROGRAM (25h) command sequence.

Removing VHH from the VPP upon completion of the embedded program operation re-

turns the device to normal operation.

Table 13: ACCELERATED PROGRAM Requirements and Recommendations

Device State Requirements/Recommendations

Device blocks Requirement: Must be unprotected prior to raising VPP/WP# to VHH

VHH applied to VPP/WP# Requirement: Maximum cumulative period of 80 hours.

VPP/WP# Requirement: Must not be at VHH for operations except ACCELERATED BUFFERED PRO-

GRAM and CHIP ERASE; otherwise device can be damaged

Recommendation: Keep stable to VHH during ACCELERATED BUFFERED PROGRAM opera-

tion

Power-up Recommendation: Apply VHH on VPP/WP# after VCC/VCCQ is stable on.

Power-down Recommendation: Adjust VPP/WP# from VHH to VIH/VIL before VCC/VCCQ goes LOW.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Program Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Erase Operations

CHIP ERASE Command

The CHIP ERASE (80/10h) command erases the entire chip. Six bus WRITE operations

are required to issue the command and start the program/erase controller.

Protected blocks are not erased. If all blocks are protected, the data remains unchanged.

No error is reported when protected blocks are not erased.

During the CHIP ERASE operation, the device ignores all other commands, including

ERASE SUSPEND. It is not possible to abort the operation. All bus READ operations dur-

ing CHIP ERASE output the data polling register on the data I/Os. See the Data Polling

After the CHIP ERASE operation completes, the device returns to read mode, unless an

error has occurred. If an error occurs, the device will continue to output the data polling

When the operation fails, a READ/RESET command must be issued to reset the error

condition and return to read mode. The status of the array must be confirmed through

the BLANK CHECK operation and the BLOCK ERASE command re-issued to the failed

block.

The CHIP ERASE command sets all of the bits in unprotected blocks of the device to 1.

All previous data is lost.

The operation is aborted by performing a reset or by powering down the device. In this

case, data integrity cannot be ensured, and it is recommended that the entire chip be

erased again.

UNLOCK BYPASS CHIP ERASE Command

When the device is in unlock bypass mode, the UNLOCK BYPASS CHIP ERASE (80/10h)

command can be used to erase all memory blocks at one time. The command requires

only two bus WRITE operations instead of six using the standard CHIP ERASE com-

mand. The final bus WRITE operation starts the program/erase controller.

The UNLOCK BYPASS CHIP ERASE command behaves the same way as the CHIP

ERASE command: the operation cannot be aborted, and a bus READ operation to the

memory outputs the data polling register.

BLOCK ERASE Command

The BLOCK ERASE (80/30h) command erase one block. It sets all bits in the unprotec-

ted selected block to 1. All previous data in the selected block are lost. Six bus WRITE

operations are required to select the block to be erased.

After the sixth bus WRITE operation, a bus READ operation outputs the data polling

program/erase controller has started the BLOCK ERASE operation.

After the BLOCK ERASE operation completes, the device returns to read mode, unless

an error has occurred. If an error occurs, bus READ operations will continue to output

the data polling register. A READ/RESET command must be issued to reset the error

condition and return to read mode.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Erase Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 39 Micron Technology, Inc. reserves the right to change products or specifications without notice.

If the selected block is protected, it is ignored and the data remains unchanged. No er-

ror condition is given when protected block is not erased.

During the BLOCK ERASE operation, the device ignores all commands except the

ERASE SUSPEND command and the READ STATUS command. The operation is abor-

ted by performing a hardware reset or powering down the device. In this case, data in-

tegrity cannot be ensured, and it is recommended that the aborted blocks be erased

again.

UNLOCK BYPASS BLOCK ERASE Command

When the device is in unlock bypass mode, the UNLOCK BYPASS BLOCK ERASE

(80/30h) command can be used to erase one memory block. The command requires

two bus WRITE operations instead of six using the standard BLOCK ERASE command.

The final bus WRITE operation latches the address of the block and starts the program/

erase controller.

The UNLOCK BYPASS BLOCK ERASE command behaves the same way as the BLOCK

ERASE command: the operation cannot be aborted, and a bus READ operation to the

memory outputs the data polling register. See the BLOCK ERASE Command section for

details.

ERASE SUSPEND Command

The ERASE SUSPEND (B0h) command temporarily suspends a BLOCK ERASE opera-

tion. One bus WRITE operation is required to issue the command. The block address is

"Don't Care."

The program/erase controller suspends the ERASE operation within the erase suspend

latency time of the ERASE SUSPEND command being issued. However, when the

ERASE SUSPEND command is written during the block erase timeout, the device im-

mediately terminates the timeout period and suspends the ERASE operation. After the

program/erase controller has stopped, the device operates in read mode, and the erase

is suspended.

During an ERASE SUSPEND operation, it is possible to execute these operations in ar-

rays that are not suspended:

• READ (main memory array)

• PROGRAM

• WRITE TO BUFFER PROGRAM

• AUTO SELECT

• READ CFI

• UNLOCK BYPASS

• Extended memory block commands

• READ/RESET

Reading from a suspended block will output the data polling register. If an attempt is

made to program in a protected or suspended block, the PROGRAM command is ignor-

ed and the data remains unchanged; also, the data polling register is not read and no

error condition is given.

Before the RESUME command is initiated, the READ/RESET command must to issued

to exit AUTO SELECT and READ CFI operations. In addition, the EXIT UNLOCK BYPASS

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Erase Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 40 Micron Technology, Inc. reserves the right to change products or specifications without notice.

and EXIT EXTENDED MEMORY BLOCK commands must be issued to exit unlock by-

pass and the extended memory block modes.

An ERASE SUSPEND command is ignored if it is written during a CHIP ERASE opera-

tion.

If the ERASE SUSPEND operation is aborted by performing a device hardware reset or

power-down, data integrity cannot be ensured, and it is recommended that the suspen-

ded blocks be erased again.

ERASE RESUME Command

The ERASE RESUME (30h) command restarts the program/erase controller after an

ERASE SUSPEND operation.

The device must be in read array mode before the RESUME command will be accepted.

An erase can be suspended and resumed more than once.

ACCELERATED CHIP ERASE Operations

The ACCELERATED CHIP ERASE operation provides faster performance than the

standard CHIP ERASE command sequence. Operations are enabled through VPP/WP#

under the VHH voltage supply.

When the system asserts VHH on input, the device automatically enters the UNLOCK

BYPASS mode, which enables the system to use the UNLOCK BYPASS CHIP ERASE

(80/30h) command sequence.

When a block is protected, the CHIP ERASE command skips the protected block and

continues with next block erase. The command algorithm skips a block that failed to

erase and continues with the remaining blocks. The fail flag will be set for the operation.

Removing VHH from the VPP/WP# upon completion of the embedded erase operation

returns the device to normal operation. When an error occurs or when the operation

fails, the array status should be confirmed through the BLANK CHECK operation and

the BLOCK ERASE command re-issued to the failed block.

Table 14: ACCELERATED CHIP ERASE Requirements and Recommendations

Device Component/State Requirements/Recommendations

VPP/WP# Requirement: Must not be at VHH for operations except ACCELERATED PROGRAM and

CHIP ERASE; otherwise device can be damaged.

VHH applied to VPP/WP# Requirement: Maximum cumulative period of 80 hours.

Power-up Recommendation: Apply VHH on VPP/WP# after VCC/VCCQ is stable on.

Power-down Recommendation: Adjust VPP/WP# from VHH to VIH/VIL before VCC/VCCQ goes LOW.

BLANK CHECK Operation

The BLANK CHECK operation determines whether a specified block is blank (that is,

completely erased). It can also be used to determine whether a previous ERASE opera-

tion was successful, including ERASE operations that might have been interrupted by

power loss.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

ACCELERATED CHIP ERASE Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 41 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The BLANK CHECK operation checks for cells that are programmed or over-erased. If it

finds any, it returns a failure status, indicating that the block is not blank. If it returns a

passing status, the block is guaranteed blank (all 1s) and is ready to program.

Before executing, the ERASE operation initiates an embedded BLANK CHECK opera-

tion, and if the target block is blank, the ERASE operation is skipped, benefitting overall

cycle performance; otherwise, the ERASE operation continues.

The BLANK CHECK operation can occur in only one block at a time, and during its exe-

cution, reading the data polling register is the only other operation allowed. Reading

from any address in the device enables reading the data polling register to monitor

blank check progress or errors. Operations such as READ (array data), PROGRAM,

ERASE, and any suspended operation are not allowed.

After the BLANK CHECK operation has completed, the device returns to read mode un-

less an error has occurred. When an error occurs, the device continues to output data

polling register data. A READ/RESET command must be issued to reset the error condi-

tion and return the device to read mode.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

BLANK CHECK Operation

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 42 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Device Protection

Hardware Protection

The VPP/WP# function provides a hardware method of protecting either the highest or

lowest block. When VPP/WP# is LOW, PROGRAM and ERASE operations on either of

these block options is ignored to provide protection. When VPP/WP# is HIGH, the de-

vice reverts to the previous protection status for the highest or lowest block. PROGRAM

and ERASE operations can modify the data in either of these block options unless block

protection is enabled.

Note: Micron highly recommends driving VPP/WP# HIGH or LOW. If a system needs to

float the VPP/WP# pin, without a pull-up/pull-down resistor and no capacitor, then an

internal pull-up resistor is enabled.

Table 15: VPP/WP# Functions

VPP/WP# Settings Function

VIL Highest or lowest block is protected.

VIH Highest or lowest block is unprotected unless software protection is activated.

Software Protection

The following software protection modes are available:

• Volatile protection

• Nonvolatile protection

• Password protection

The device is shipped with all blocks unprotected. On first use, the device defaults to

the nonvolatile protection mode but can be activated in either the nonvolatile protec-

tion or password protection mode.

The desired protection mode is activated by setting either the nonvolatile protection

mode lock bit or the password protection mode lock bit of the lock register (see the Lock

ter the protection mode has been activated, it cannot be changed, and the device is set

permanently to operate in the selected protection mode. It is recommended that the

desired software protection mode be activated when first programming the device.

For the highest or lowest block, a higher level of block protection can be achieved by

locking the block using nonvolatile protection mode and holding VPP /WP# LOW.

Blocks with volatile protection and nonvolatile protection can coexist within the memo-

ry array. If the user attempts to program or erase a protected block, the device ignores

the command and returns to read mode.

The block protection status can be read by performing a read electronic signature or by

issuing an AUTO SELECT command (see the Block Protection table).

Refer to the Block Protection Status table and the Software Protection Scheme figure for

details on the block protection scheme. Refer to the Protection Operations section for a

description of the command sets.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Device Protection

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 43 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Volatile Protection Mode

Volatile protection enables the software application to protect blocks against inadver-

tent change and can be disabled when changes are needed. Volatile protection bits are

unique for each block and can be individually modified. Volatile protection bits control

the protection scheme only for unprotected blocks whose nonvolatile protection bits

are cleared to 1. Issuing a PROGRAM VOLATILE PROTECTION BIT or CLEAR VOLATILE

PROTECTION BIT command sets to 0 or clears to 1 the volatile protection bits and pla-

ces the associated blocks in the protected (0) or unprotected (1) state, respectively. The

volatile protection bit can be set or cleared as often as needed.

When the device is first shipped, or after a power-up or hardware reset, the volatile pro-

tection bits default to 1 (unprotected).

Nonvolatile Protection Mode

A nonvolatile protection bit is assigned to each block. Each of these bits can be set for

protection individually by issuing a PROGRAM NONVOLATILE PROTECTION BIT com-

mand. Also, each device has one global volatile bit called the nonvolatile protection bit

lock bit; it can be set to protect all nonvolatile protection bits at once. This global bit

must be set to 0 only after all nonvolatile protection bits are configured to the desired

settings. When set to 0, the nonvolatile protection bit lock bit prevents changes to the

state of the nonvolatile protection bits. When cleared to 1, the nonvolatile protection

bits can be set and cleared using the PROGRAM NONVOLATILE PROTECTION BIT and

CLEAR ALL NONVOLATILE PROTECTION BITS commands, respectively.

No software command unlocks the nonvolatile protection bit lock bit unless the device

is in password protection mode; in nonvolatile protection mode, the nonvolatile protec-

tion bit lock bit can be cleared only by taking the device through a hardware reset or

power-up.

Nonvolatile protection bits cannot be cleared individually; they must be cleared all at

once using a CLEAR ALL NONVOLATILE PROTECTION BITS command. They will re-

main set through a hardware reset or a power-down/power-up sequence.

If one of the nonvolatile protection bits needs to be cleared (unprotected), additional

steps are required: First, the nonvolatile protection bit lock bit must be cleared to 1, us-

ing either a power-cycle or hardware reset. Then, the nonvolatile protection bits can be

changed to reflect the desired settings. Finally, the nonvolatile protection bit lock bit

must be set to 0 to lock the nonvolatile protection bits. The device now will operate nor-

mally.

To achieve the best protection, the PROGRAM NONVOLATILE PROTECTION LOCK BIT

command should be executed early in the boot code, and the boot code should be pro-

tected by holding VPP/WP# LOW.

Nonvolatile protection bits and volatile protection bits have the same function when

VPP/WP# is HIGH or when VPP/WP# is at the voltage for program acceleration (VHH ).

Password Protection Mode

The password protection mode provides a higher level of security than the nonvolatile

protection mode by requiring a 64-bit password to unlock the nonvolatile protection bit

lock bit. In addition to this password requirement, the nonvolatile protection bit lock

bit is set to 0 after power-up and reset to maintain the device in password protection

mode.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Device Protection

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 44 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Executing the UNLOCK PASSWORD command by entering the correct password clears

the nonvolatile protection bit lock bit, enabling the block nonvolatile protection bits to

be modified. If the password provided is incorrect, the nonvolatile protection bit lock

bit remains locked, and the state of the nonvolatile protection bits cannot be modified.

To place the device in password protection mode, the following two steps are required:

First, before activating the password protection mode, a 64-bit password must be set

and the setting verified. Password verification is allowed only before the password pro-

tection mode is activated. Next, password protection mode is activated by program-

ming the password protection mode lock bit to 0. This operation is irreversible. After the

bit is programmed, it cannot be erased, the device remains permanently in password

protection mode, and the 64-bit password can be neither retrieved nor reprogrammed.

In addition, all commands to the address where the password is stored are disabled.

Note: There is no means to verify the password after password protection mode is ena-

bled. If the password is lost after enabling the password protection mode, there is no

way to clear the nonvolatile protection bit lock bit.

Figure 11: Software Protection Scheme

1 = unprotected (default)

0 = protected

1 = unprotected

0 = protected

(Default setting depends on the product order option)

Volatile protection bit Nonvolatile protection bit

1 = unlocked (default, after power-up or hardware reset)

0 = locked

Nonvolatile protection bit lock bit (volatile)

Nonvolatile protection

mode

Password protection

mode

Volatile

protection

Nonvolatile

protection

Array block

Notes: 1. Volatile protection bits are programmed and cleared individually. Nonvolatile protection

bits are programmed individually and cleared collectively.

2. Once programmed to 0, the nonvolatile protection bit lock bit can be reset to 1 only by

taking the device through a power-up or hardware reset.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Device Protection

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 45 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 16: Block Protection Status

Nonvolatile

Protection Bit

Lock Bit1

Nonvolatile

Protection

Bit2

Volatile

Protection

Bit3

Block

Protection

Status4Block Protection Status

1 1 1 00h Block unprotected; nonvolatile protection bit changeable.

1 1 0 01h Block protected by volatile protection bit; nonvolatile pro-

tection bit changeable.

1 0 1 01h Block protected by nonvolatile protection bit; nonvolatile

protection bit changeable.

1 0 0 01h Block protected by nonvolatile protection bit and volatile

protection bit; nonvolatile protection bit changeable.

0 1 1 00h Block unprotected; nonvolatile protection bit unchangeable.

0 1 0 01h Block protected by volatile protection bit; nonvolatile pro-

tection bit unchangeable.

0 0 1 01h Block protected by nonvolatile protection bit; nonvolatile

protection bit unchangeable.

0 0 0 01h Block protected by nonvolatile protection bit and volatile

protection bit; nonvolatile protection bit unchangeable.

Notes: 1. Nonvolatile protection bit lock bit: when cleared to 1, all nonvolatile protection bits are

unlocked; when set to 0, all nonvolatile protection bits are locked.

2. Block nonvolatile protection bit: when cleared to 1, the block is unprotected; when set

to 0, the block is protected.

3. Block volatile protection bit: when cleared to 1, the block is unprotected; when set to 0,

the block is protected.

4. Block protection status is checked under AUTO SELECT mode.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Device Protection

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 46 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Block Protection Command Definitions – Address-Data Cycles

Table 17: Block Protection Command Definitions – Address-Data Cycles

Notes 1 and 2 apply to entire table

Command and

Code/Subcode

Address and Data Cycles

Notes

1st 2nd 3rd 4th

…

nth

A D A D A D A D A D

LOCK REGISTER Commands

ENTER LOCK

COMMAND SET (40h)

555 AA 2AA 55 555 40 3

PROGRAM LOCK

X A0 X Data 5

READ LOCK REGISTER X Data 4, 5, 6

EXIT LOCK REGISTER

(90h/00h)

X 90 X 00 3

PASSWORD PROTECTION Commands

ENTER PASSWORD

PROTECTION

COMMAND SET (60h)

555 AA 2AA 55 555 60 3

PROGRAM

PASSWORD (A0h)

X A0 PWAn PWDn 7

READ PASSWORD 00 PWD0 01 PWD1 02 PWD2 03 PWD3 4, 6, 8

UNLOCK PASSWORD

(25h/03h)

00 25 00 03 00 PWD0 01 PWD1 … 00 29 8

EXIT PASSWORD

PROTECTION (90h/00h)

X 90 X 00 3

NONVOLATILE PROTECTION Commands

ENTER NONVOLATILE

PROTECTION

COMMAND SET (C0h)

555 AA 2AA 55 555 C0 3

PROGRAM

NONVOLATILE

PROTECTION BIT (A0h)

X A0 BAd 00 9

READ NONVOLATILE

PROTECTION BIT

STATUS

BAd READ

(DQ0)

4, 6, 9

CLEAR ALL

NONVOLATILE

PROTECTION

BITS (80h/30h)

X 80 00 30 10

EXIT NONVOLATILE

PROTECTION (90h/00h)

X 90 X 00 3

NONVOLATILE PROTECTION BIT LOCK BIT Commands

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Block Protection Command Definitions – Address-Data Cycles

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 47 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 17: Block Protection Command Definitions – Address-Data Cycles (Continued)

Notes 1 and 2 apply to entire table

Command and

Code/Subcode

Address and Data Cycles

Notes

1st 2nd 3rd 4th

…

nth

A D A D A D A D A D

ENTER NONVOLATILE

PROTECTION BIT

LOCK BIT

COMMAND SET (50h)

555 AA 2AA 55 555 50 3

PROGRAM

NONVOLATILE

PROTECTION BIT

LOCK BIT (A0h)

X A0 X 00 9

READ NONVOLATILE

PROTECTION BIT

LOCK BIT STATUS

X READ

(DQ0)

4, 6, 9

EXIT NONVOLATILE

PROTECTION BIT

LOCK BIT (90h/00h)

X 90 X 00 3

VOLATILE PROTECTION Commands

ENTER VOLATILE

PROTECTION

COMMAND SET (E0h)

555 AA 2AA 55 555 E0 3

PROGRAM VOLATILE

PROTECTION BIT (A0h)

X A0 BAd 00 9

READ VOLATILE

PROTECTION BIT

STATUS

BAd READ

(DQ0)

4, 6

CLEAR VOLATILE

PROTECTION BIT (A0h)

X A0 BAd 01 9

EXIT VOLATILE

PROTECTION (90h/00h)

X 90 X 00 3

EXTENDED MEMORY BLOCK Operations

ENTER EXTENDED

MEMORY BLOCK (88h)

555 AA 2AA 55 555 88

PROGRAM EXTENDED

MEMORY BLOCK (A0h)

555 AA 2AA 55 555 A0 Word

address

data

READ EXTENDED

MEMORY BLOCK

Word

address

data

EXIT EXTENDED

MEMORY BLOCK

(90h/00h)

555 AA 2AA 55 555 90 X 00

Notes: 1. Key: A = Address and D = Data; X = "Don’t Care;" BAd = Any address in the block; PWDn

= Password words, n = 0 to 3; PWAn = Password address, n = 0 to 3; Gray = Not applica-

ble. All values in the table are hexadecimal.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Block Protection Command Definitions – Address-Data Cycles

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 48 Micron Technology, Inc. reserves the right to change products or specifications without notice.

2. DQ[15:8] are "Don’t Care" during UNLOCK and COMMAND cycles. A[MAX:16] are

"Don’t Care" during UNLOCK and COMMAND cycles, unless an address is required.

3. The ENTER command sequence must be issued prior to any operation. It disables READ

and WRITE operations from and to block 0. READ and WRITE operations from and to

any other block are allowed. Also, when an ENTER COMMAND SET command is issued,

an EXIT COMMAND SET command must be issued to return the device to READ mode.

4. READ REGISTER/PASSWORD commands have no command code; CE# and OE# are driven

LOW and data is read according to a specified address.

5. Data = Lock register content.

6. All address cycles shown for this command are READ cycles.

7. Only one portion of the password can be programmed or read by each PROGRAM PASS-

WORD command.

8. Each portion of the password can be entered or read in any order as long as the entire

64-bit password is entered or read.

9. Both nonvolatile and volatile protection bit settings are as follows: Protected state = 00;

Unprotected state = 01.

10. The CLEAR ALL NONVOLATILE PROTECTION BITS command programs all nonvolatile pro-

tection bits before erasure. This prevents over-erasure of previously cleared nonvolatile

protection bits.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Block Protection Command Definitions – Address-Data Cycles

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 49 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Protection Operations

Blocks can be protected individually against accidental PROGRAM or ERASE opera-

tions. The block protection scheme is shown in the Software Protection Scheme figure.

Memory block and extended memory block protection is configured through the lock

LOCK REGISTER Commands

After the ENTER LOCK REGISTER COMMAND SET (40h) command has been issued, all

bus READ or PROGRAM operations can be issued to the lock register.

The PROGRAM LOCK REGISTER (A0h) command allows the lock register to be config-

ured. The programmed data can then be checked with a READ LOCK REGISTER com-

mand by driving CE# and OE# LOW with the appropriate address data on the address

bus.

PASSWORD PROTECTION Commands

After the ENTER PASSWORD PROTECTION COMMAND SET (60h) command has been

issued, the commands related to password protection mode can be issued to the device.

The PROGRAM PASSWORD (A0h) command is used to program the 64-bit password

used in the password protection mode. To program the 64-bit password, the complete

command sequence must be entered four times at four consecutive addresses selected

by A[1:0]. By default, all password bits are set to 1. The password can be checked by is-

suing a READ PASSWORD command.

Note: A password must be programmed per Flash memory die to enable password pro-

tection.

The READ PASSWORD command is used to verify the password used in password pro-

tection mode. To verify the 64-bit password, the complete command sequence must be

entered four times at four consecutive addresses selected by A[1:0]. If the password

mode lock bit is programmed and the user attempts to read the password, the device

will output 00h onto the I/O data bus.

The UNLOCK PASSWORD (25/03h) command is used to clear the nonvolatile protec-

tion bit lock bit, allowing the nonvolatile protection bits to be modified. The UNLOCK

PASSWORD command must be issued, along with the correct password, and requires a

6μs delay between successive UNLOCK PASSWORD commands in order to prevent

hackers from cracking the password by trying all possible 64-bit combinations. If this

delay does not occur, the latest command will be ignored. Approximately 6μs is re-

quired for unlocking the device after the valid 64-bit password has been provided.

NONVOLATILE PROTECTION Commands

After the ENTER NONVOLATILE PROTECTION COMMAND SET (C0h) command has

been issued, the commands related to nonvolatile protection mode can be issued to the

device.

A block can be protected from program or erase by issuing a PROGRAM NONVOLATILE

PROTECTION BIT (A0h) command, along with the block address. This command sets

the nonvolatile protection bit to 0 for a given block.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Protection Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 50 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The status of a nonvolatile protection bit for a given block or group of blocks can be

read by issuing a READ NONVOLATILE MODIFY PROTECTION BIT command, along

with the block address.

The nonvolatile protection bits are erased simultaneously by issuing a CLEAR ALL

NONVOLATILE PROTECTION BITS (80/30h) command. No specific block address is re-

quired. If the nonvolatile protection bit lock bit is set to 0, the command fails.

Figure 12: Set/Clear Nonvolatile Protection Bit Algorithm Flowchart

Yes

Success

Done?

Match

expected value?

DQ0 = 1 (clear)

or 0 (set)

ENTER NONVOLATILE

PROTECTION

command set

Start

PROGRAM/CLEAR

NONVOLATILE

PROTECTION BIT

Polling algorithm

READ NONVOLATILE

PROTECTION

BIT STATUS

EXIT PROTECTION

command set

Notes: 1. See the Block Protection Command Definitions table for address-data cycle details.

2. DQ5 and DQ1 are ignored in this algorithm flow.

NONVOLATILE PROTECTION BIT LOCK BIT Commands

After the ENTER NONVOLATILE PROTECTION BIT LOCK BIT COMMAND SET (50h)

command has been issued, the commands that allow the nonvolatile protection bit lock

bit to be set can be issued to the device.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Protection Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 51 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The PROGRAM NONVOLATILE PROTECTION BIT LOCK BIT (A0h) command is used to

set the nonvolatile protection bit lock bit to 0, thus locking the nonvolatile protection

bits and preventing them from being modified.

The READ NONVOLATILE PROTECTION BIT LOCK BIT STATUS command is used to

read the status of the nonvolatile protection bit lock bit.

VOLATILE PROTECTION Commands

After the ENTER VOLATILE PROTECTION COMMAND SET (E0h) command has been

issued, commands related to the volatile protection mode can be issued to the device.

The PROGRAM VOLATILE PROTECTION BIT (A0h) command individually sets a vola-

tile protection bit to 0 for a given block. If the nonvolatile protection bit for the same

block is set, the block is locked regardless of the value of the volatile protection bit (see

the Block Protection Status table).

The status of a volatile protection bit for a given block can be read by issuing a READ

VOLATILE PROTECTION BIT STATUS command along with the block address.

The CLEAR VOLATILE PROTECTION BIT (A0h) command individually clears (sets to 1)

the volatile protection bit for a given block. If the nonvolatile protection bit for the same

block is set, the block is locked regardless of the value of the volatile protection bit (see

the Block Protection Status table).

EXTENDED MEMORY BLOCK Commands

The device has one extra 512-word extended memory block that can be accessed only

by the ENTER EXTENDED MEMORY BLOCK (88h) command. It is used as a security

block to provide a permanent 128-bit secure ID number or to store additional informa-

tion. The device can be shipped with the extended memory block prelocked perma-

nently by Micron, including the 128-bit security identification number. Or, the device

can be shipped with the extended memory block unlocked, enabling customers to per-

manently program and lock it (default) (see Lock Register, the AUTO SELECT com-

mand, and the Block Protection table.)

Table 18: Extended Memory Block Address and Data

Address

Data

Micron Prelocked Customer Lockable

000000h–

000007h

Secure ID number Determined by customer (default)

000008h–

0001FFh

Protected and

unavailable

After the ENTER EXTENDED MEMORY BLOCK command has been issued, the device

enters the extended memory block mode. All bus READ or PROGRAM operations are

conducted on the extended memory block, and the extended memory block is ad-

dressed using the addresses occupied by block 0 in the other operating modes (see the

Memory Map table).

In extended memory block mode, ERASE, CHIP ERASE, ERASE SUSPEND, and ERASE

RESUME commands are not allowed. The extended memory block cannot be erased,

and each bit of the extended memory block can only be programmed once.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Protection Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 52 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The extended memory block is protected from further modification by programming

lock register bit 0. Once invoked, this protection cannot be undone.

The device remains in extended memory block mode until the EXIT EXTENDED MEM-

ORY BLOCK (90/00h) command is issued, which returns the device to read mode, or

until power is removed from the device. After a power-up sequence or hardware reset,

the device will revert to reading memory blocks in the main array.

EXIT PROTECTION Command

The EXIT PROTECTION COMMAND SET (90/00h) command is used to exit the lock

tile protection bit lock bit command set modes and return the device to read mode.

Note that the READ/RESET command (F0h) is ignored under these modes.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Protection Operations

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 53 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Common Flash Interface

The common flash interface (CFI) is a JEDEC-approved, standardized data structure

that can be read from the flash memory device. It allows a system's software to query

the device to determine various electrical and timing parameters, density information,

and functions supported by the memory. The system can interface easily with the de-

vice, enabling the software to upgrade itself when necessary.

When the READ CFI command is issued, the device enters CFI query mode and the data

structure is read from memory. The following tables show the addresses (A[7:0]) used to

retrieve the data. The query data is always presented on the lowest order data outputs

(DQ[7:0]), and the other data outputs (DQ[15:8]) are set to 0.

Table 19: Query Structure Overview

Note 1 applies to the entire table

Address Subsection Name Description

10h CFI query identification string Command set ID and algorithm data offset

1Bh System interface information Device timing and voltage information

27h Device geometry definition Flash device layout

40h Primary algorithm-specific extended query table Additional information specific to the primary algo-

rithm (optional)

Note: 1. Query data are always presented on the lowest order data outputs (DQ[7:0]). DQ[15:8]

are set to 0.

Table 20: CFI Query Identification String

Note 1 applies to the entire table

Address Data Description Value

10h 0051h Query unique ASCII string "QRY" "Q"

11h 0052h "R"

12h 0059h "Y"

13h

14h

0002h

0000h

Primary algorithm command set and control interface ID code 16-bit ID code de-

fining a specific algorithm

–

15h

16h

0040h

0000h

Address for primary algorithm extended query table (see the Primary Algorithm-

Specific Extended Query Table)

P = 40h

17h

18h

0000h

Alternate vendor command set and control interface ID code second vendor-speci-

fied algorithm supported

–

19h

1Ah

0000h

Address for alternate algorithm extended query table –

Note: 1. Query data are always presented on the lowest order data outputs (DQ[7:0]). DQ[15:8]

are set to 0.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Common Flash Interface

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 54 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 21: CFI Query System Interface Information

Note 1 applies to the entire table

Address Data Description Value

1Bh 0027h VCC logic supply minimum program/erase voltage

Bits[7:4] BCD value in volts

Bits[3:0] BCD value in 100mV

2.7V

1Ch 0036h VCC logic supply maximum program/erase voltage

Bits[7:4] BCD value in volts

Bits[3:0] BCD value in 100mV

3.6V

1Dh 0085h VHH (programming) supply minimum program/erase voltage

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

8.5V

1Eh 0095h VHH (programming) supply maximum program/erase voltage

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 10mV

9.5V

1Fh 0005h Typical timeout for single byte/word program = 2nμs 32µs

20h 0009h Typical timeout for maximum size buffer program = 2nμs 512µs

21h 0008h Typical timeout per individual block erase = 2nms 256ms

22h 0012h Typical timeout for full chip erase = 2nms 262s

23h 0003h Maximum timeout for byte/word program = 2n times typical 256µs

24h 0002h Maximum timeout for buffer program = 2n times typical 2048µs

25h 0003h Maximum timeout per individual block erase = 2n times typical 2s

26h 0003h Maximum timeout for chip erase = 2n times typical 2096s

Note: 1. The values in this table are valid for all packages.

Table 22: Device Geometry Definition

Address Data Description Value

27h 001Bh Device size = 2n in number of bytes 128MB

28h

29h

0001h

0000h

Flash device interface code description x16

asynchronous

2Ah

2Bh

000Ah

0000h

Maximum number of bytes in multi-byte program or page = 2n1024

2Ch 0001h Number of erase block regions. It specifies the number of regions

containing contiguous erase blocks of the same size.

2Dh

2Eh

00FFh

0003h

Erase block region 1 information

Number of identical-size erase blocks = 01FFh + 1

1024

2Fh

30h

0000h

0002h

Erase block region 1 information

Block size in region 1 = 0200h × 256 bytes

128KB

31h

32h

33h

34h

0000h

Erase block region 2 information 0

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Common Flash Interface

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 55 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 22: Device Geometry Definition (Continued)

Address Data Description Value

35h

36h

37h

38h

0000h

Erase block region 3 information 0

39h

3Ah

3Bh

3Ch

0000h

Erase block region 4 information 0

3Dh

3Eh

3Fh

FFFFh

Reserved –

Table 23: Primary Algorithm-Specific Extended Query Table

Note 1 applies to the entire table

Address Data Description Value

40h 0050h Primary algorithm extended query table unique ASCII string “PRI” "P"

41h 0052h "R"

42h 0049h "I"

43h 0031h Major version number, ASCII "1"

44h 0035h Minor version number, ASCII "5"

45h 001Ch Address sensitive unlock (bits[1:0]):

00 = Required

01 = Not required

Process technology (bits [7:2])

0111b: Second generation

Required

46h 0002h Erase suspend:

00 = Not supported

01 = Read only

02 = Read and write

47h 0001h Block protection:

00 = Not supported

x = Number of blocks per group

48h 0000h Temporary block unprotect scheme:

00 = Not supported

01 = Supported

Not supported

49h 0008h Protect/unprotect scheme:

08 = Advanced sector protection method

4Ah 0000h Simultaneous operations:

Not supported

–

4Bh 0000h Burst mode:

00 = Not supported

01 = Supported

Not supported

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Common Flash Interface

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 56 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 23: Primary Algorithm-Specific Extended Query Table (Continued)

Note 1 applies to the entire table

Address Data Description Value

4Ch 0003h Page mode:

00 = Not supported

01 = 4-word page

02 = 8-word page

03 = 16-word page

16-word page

4Dh 0085h VHH supply minimum program/erase voltage:

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

8.5V

4Eh 0095h VHH supply maximum program/erase voltage:

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

9.5V

4Fh 00xxh WP# protection:

xx = 04h: Uniform device, HW protection for lowest block

xx = 05h: Uniform device, HW protection for highest block

Uniform + VPP/WP#

protecting highest

or lowest block

50h 0001h Program suspend:

00 = Not supported

01 = Supported

Supported

51h 0001h Unlock bypass:

00 = Not supported

01 = Supported

Supported

52h 000Ah Extended memory block (customer OTP area): 2n bytes 1024 bytes

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Common Flash Interface

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 57 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 23: Primary Algorithm-Specific Extended Query Table (Continued)

Note 1 applies to the entire table

Address Data Description Value

53h 008Fh Software Features –

bit 0: Status register polling

00 = Not supported

01 = Supported)

bit 1: DQ polling

00 = Not supported

01 = Supported)

bit 2: Program suspend/resume commands

00 = Not supported

01 = Supported)

bit 3: Word programming

00 = Not supported

01 = Supported)

bit 4: Bit-field programming

00 = Not supported

01 = Supported)

bit 5: Autodetect programming

00 = Not supported

01 = Supported)

bit 6: RFU

bit 7: Multiple writes per line

00 = Not supported

01 = Supported)

54h 0005h Page size: 2n bytes 32 bytes

55h 0005h Erase suspend timeout maximum: 2n (µs) 32µs

56h 0004h Program suspend timeout maximum: 2n (µs) 16µs

57h to 77h FFFFh Reserved –

78h 0005h tPLRH maximum: 2n (µs) 32µs

79h 0009h tVCCPH maximum: 2n (µs)

Power-on reset

512µs

Note: 1. The values in this table are valid for both packages.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Common Flash Interface

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 58 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Power-Up and Reset Characteristics

Table 24: Power-Up Specifications

Note 1 applies to entire table.

Parameter

Symbol

Min Unit NotesLegacy JEDEC

VCC HIGH to VCCQ HIGH – tVCHVCQH 0 µs 2

VCC HIGH to rising edge of RST# tVCS tVCHPH 300 µs 3, 4

VCCQ HIGH to rising edge of RST# tVIOS tVCQHPH 0 µs 3, 4

RST# HIGH to chip enable LOW tRH tPHEL 50 ns

RST# HIGH to write enable LOW – tPHWL 150 ns

Notes: 1. Sampled only; not 100% tested.

2. VCC should attain VCC,min from VSS simultaneously with or prior to applying VCCQ during

power up. VCC should attain VSS during power down.

3. If RST# is not stable for tVCS or tVIOS, the device will not allow any READ or WRITE oper-

ations, and a hardware reset is required.

4. Power supply transitions should only occur when RST# is LOW.

Figure 13: Power-Up Timing

tRH

tVIOS

tVCS

tPHWL

tVCHVCQH

VCCQ

VCC

CE#

RST#

WE#

VSSQ

VSS

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Power-Up and Reset Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 59 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 25: Reset AC Specifications

Condition/Parameter

Symbol

Min Max Unit NotesLegacy JEDEC

RST# LOW to read mode during program or

erase

tREADY tPLRH – 25 µs 1

RST# pulse width tRP tPLPH 100 – ns

RST# HIGH to CE# LOW, OE# LOW tRH tPHEL, tPHGL 50 – ns 1

RST# LOW to standby mode during read mode tRPD – 0 – µs

RST# LOW to standby mode during program or

erase

0 – µs

RY/BY# HIGH to CE# LOW, OE# LOW tRB tRHEL, tRHGL 0 – ns 1

Note: 1. Sampled only; not 100% tested.

Figure 14: Reset AC Timing – No PROGRAM/ERASE Operation in Progress

tRH

RY/BY#

CE#, OE#

RST#

tRP

Figure 15: Reset AC Timing During PROGRAM/ERASE Operation

tRB

RY/BY#

CE#, OE#

RST#

tRP

tRH

tREADY

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Power-Up and Reset Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 60 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Absolute Ratings and Operating Conditions

Stresses greater than those listed may cause permanent damage to the device. This is a

stress rating only, and functional operation of the device at these or any other condi-

tions outside those indicated in the operational sections of this specification is not im-

plied. Exposure to absolute maximum rating conditions for extended periods may ad-

versely affect reliability.

Table 26: Absolute Maximum/Minimum Ratings

Parameter Symbol Min Max Unit Notes

Temperature under bias TBIAS –50 125 °C

Storage temperature TSTG –65 150 °C

Supply voltage VCC –0.6 VCC + 2 V 1, 2

Input/output supply voltage VCCQ –0.6 VCCQ + 2 V 1, 2

Program/erase voltage VPP –0.6 9.5 V 3

Notes: 1. During signal transitions, minimum voltage may undershoot to −2V for periods less than

20ns.

2. During signal transitions, maximum voltage may overshoot to VCC + 2V for periods less

than 20ns.

3. VPP must not remain at 9.5V for more than 80 hours cumulative.

Table 27: Operating Conditions

Parameter Symbol Min Max Unit Notes

Supply voltage VCC 2.7 3.6 V

Input/output supply voltage (VCCQ ≤ VCC) VCCQ 1.65 3.6 V

Accelerated buffered program/chip erase volt-

age

VHH 8.5 9.5 V

Ambient operating temperature TA–40 105 °C

Load capacitance CL30 pF

Input rise and fall times (VIL to VIH) – 0.3 2.5 ns 1, 2

Input pulse voltages – 0 to VCCQ V

Input and output timing reference voltages – VCCQ/2 V

Address to address skew – – 3 ns

Notes: 1. If the rise/fall time is slower than 2.5ns, all timing specs must be derated by 0.5ns for ev-

ery nanosecond push-out in rise/fall time. (Example: for a 10ns rise/fall time, all timing

specs must be derated by (10 - 2.5) × (0.5ns) = 3.75ns.

2. Applies to Address, CE#, OE#, and WE# signals.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Absolute Ratings and Operating Conditions

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 61 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 16: AC Measurement Load Circuit

VCCQ

25kΩ

Device

under

test

0.1µF

VCC

25kΩ

Note: 1. CL includes jig capacitance.

Figure 17: AC Measurement I/O Waveform

VCCQ

VCCQ/2

Table 28: Input/Output Capacitance

Parameter Symbol Test Condition Min Max Unit

Input capacitance CIN VIN = 0V 3 11 pF

Output capacitance COUT VOUT = 0V 3 7 pF

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Absolute Ratings and Operating Conditions

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 62 Micron Technology, Inc. reserves the right to change products or specifications without notice.

DC Characteristics

Table 29: DC Current Characteristics

Parameter Symbol Conditions Min Typ Max Unit Notes

Input load current ILI 0V ≤ VIN ≤ VCC – – ±1 µA 1

Output leakage current ILO 0V ≤ VOUT ≤ VCC – – ±1 µA

VCC read

current

Random read ICC1 CE# = VIL, OE# = VIH,

f = 5 MHz

– 26 31 mA

Page read CE# = VIL, OE# = VIH,

f = 13 MHz

– 12 16 mA

VCC standby

current

ICC2 CE# = VCCQ ±0.2V,

RST# = VCCQ ±0.2V

– 75 230 µA

VCC automatic

power saving (APS)

current

ICC APS VCC = VCC,max,

VCCQ = VCCQ,max

CE# = VSSQ,

RST# = VCCQ,

All inputs are at VCCQ

or VSS

– – 2 mA

VCC program/erase/blank

check current

ICC3 Program/

erase

controller

active

VPP/WP# = VIL

or VIH

– 35 50 mA 2

VPP/WP# = VHH – 35 50 mA

VPP current Read IPP1 VPP/WP# ≤ VCC – 2 15 µA

Standby IPP2 – 0.2 5 µA

PROGRAM operation

ongoing

IPP3 VPP/WP# = VHH – 5 10 mA

VPP/WP# = VCC – 0.05 0.10 mA

ERASE operation

ongoing

IPP4 VPP/WP# = VHH – 5 10 mA

VPP/WP# = VCC – 0.05 0.10 mA

Notes: 1. The maximum input load current is ±5µA on the VPP/WP# pin.

2. Sampled only; not 100% tested.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

DC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 63 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 30: DC Voltage Characteristics

Parameter Symbol Conditions Min Typ Max Unit Notes

Input LOW voltage VIL VCC ≥ 2.7V –0.5 – 0.8 V

Input HIGH voltage VIH VCC ≥ 2.7V 0.7VCCQ – VCCQ + 0.4 V

Output LOW voltage VOL IOL = 100µA,

VCC = VCC,min,

VCCQ = VCCQ,min

– – 0.15VCCQ V

Output HIGH voltage VOH IOH = 100µA,

VCC = VCC,min,

VCCQ = VCCQ,min

0.85VCCQ – – V

Voltage for VPP/WP# program

acceleration

VPP – 8.5 – 9.5 V 1

Program/erase lockout supply

voltage

VLKO – 2.0 – – V 2, 3

Notes: 1. VPP must not remain at 9.5V for more than 80 hours cumulative.

2. Sampled only; not 100% tested.

3. WRITE operations are not valid when VCC supply drops below VLKO.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

DC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 64 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Read AC Characteristics

Table 31: Read AC Characteristics – VCC = VCCQ = 2.7–3.6V

Parameter

Symbol

Condition Min Max Unit NotesLegacy JEDEC

Address valid to next address valid tRC tAVAV CE# = VIL,

OE# = VIL

105 – ns

Address valid to output valid tACC tAVQV CE# = VIL,

OE# = VIL

– 105 ns

Address valid to output valid (page) tPAGE tAVQV1 CE# = VIL,

OE# = VIL

– 20 ns

CE# LOW to output valid tCE tELQV OE# = VIL – 105 ns

OE# LOW to output valid tOE tGLQV CE# = VIL – 25 ns

CE# HIGH to output High-Z tHZ tEHQZ OE# = VIL – 20 ns 1

OE# HIGH to output High-Z tDF tGHQZ CE# = VIL – 15 ns 1

CE# HIGH, OE# HIGH, or address transi-

tion to output transition

tOH tEHQX,

tGHQX,

tAXQX

– 0 – ns

Note: 1. Sampled only; not 100% tested.

Table 32: Read AC Characteristics – VCCQ = 1.65V–VCC

Parameter

Symbol

Condition Min Max Unit NotesLegacy JEDEC

Address valid to next address valid tRC tAVAV CE# = VIL,

OE# = VIL

110 – ns

Address valid to output valid tACC tAVQV CE# = VIL,

OE# = VIL

– 110 ns

Address valid to output valid (page) tPAGE tAVQV1 CE# = VIL,

OE# = VIL

– 25 ns

CE# LOW to output valid tCE tELQV OE# = VIL – 110 ns

OE# LOW to output valid tOE tGLQV CE# = VIL – 25 ns

CE# HIGH to output High-Z tHZ tEHQZ OE# = VIL – 20 ns 1

OE# HIGH to output High-Z tDF tGHQZ CE# = VIL – 15 ns 1

CE# HIGH, OE# HIGH, or address transi-

tion to output transition

tOH tEHQX,

tGHQX,

tAXQX

– 0 – ns

Note: 1. Sampled only; not 100% tested.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Read AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 65 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 18: Random Read AC Timing

Valid

tACC

tRC

tOH

tCE

tLZ

tOH

tHZ

tOLZ tOH

tOE tDF

A[MAX:0]

CE#

OE#

DQ[15:0]

Figure 19: Page Read AC Timing

Valid

Valid Valid Valid ValidValid Valid Valid

tACC

tCE

tPAGE

tOH

tHZ

tOH

tOE

tDF

A[MAX:4]

A[3:0]

CE#

OE#

DQ[15:0] Valid Valid Valid Valid Valid Valid Valid

Note: 1. Page size is 16 words and is addressed by address inputs A[3:0].

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Read AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 66 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Write AC Characteristics

Table 33: WE#-Controlled Write AC Characteristics

Parameter

Symbol

Min Typ Max Unit NotesLegacy JEDEC

WRITE cyle time tWC – 60 – – ns

CE# LOW to WE# LOW tCS tELWL 0 – – ns

WE# LOW to WE# HIGH tWP tWLWH 35 – – ns

Input valid to WE# HIGH tDS tDVWH 30 – – ns 1

WE# HIGH to input transition tDH tWHDX 0 – – ns

WE# HIGH to CE# HIGH tCH tWHEH 0 – – ns

WE# HIGH to WE# LOW tWPH tWHWL 20 – – ns

Address valid to WE# LOW tAS tAVWL 0 – – ns

WE# LOW to address transition tAH tWLAX 45 – – ns

OE# HIGH to WE# LOW – tGHWL 0 – – ns

WE# HIGH to OE# LOW tOEH tWHGL 0 – – ns

Program/erase valid to RY/BY# LOW tBUSY tWHRL – – 90 ns 2

WE# HIGH to OE# valid – tWHQV tAVQV

+ 30

– – ns

VHH rise or fall time on VPP/WP# – tVHVPP 250 – – ns

Notes: 1. The user's write timing must comply with this specification. Any violation of this write

timing specification may result in permanent damage to the NOR Flash device.

2. Sampled only; not 100% tested.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Write AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 67 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 20: WE#-Controlled Program AC Timing

555h PA PA

3rd Cycle 4th Cycle READ CycleData Polling

tWC tWC

tAS

tWP

tDS

tDF

tWHWH1

tWPH

tAH

tCE

tCS

tGHWL tOE

tDH

tOH

tCH

A[MAX:0]

CE#

OE#

WE#

DQ[15:0] A0h PD DQ7# DOUT DOUT

Notes: 1. Only the third and fourth cycles of the PROGRAM command are represented. The PRO-

GRAM command is followed by checking of the status register data polling bit and by a

READ operation that outputs the data (DOUT) programmed by the previous PROGRAM

command.

2. PA is the address of the memory location to be programmed. PD is the data to be pro-

grammed.

3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit

[DQ7]).

4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

5. For tWHWH1 timing details, see the Program/Erase Characteristics table.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Write AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 68 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 34: CE#-Controlled Write AC Characteristics

Parameter

Symbol

Min Typ Max Unit NotesLegacy JEDEC

WRITE cycle time tWC – 60 – – ns

WE# LOW to CE# LOW tWS tWLEL 0 – – ns

CE# LOW to CE# HIGH tCP tELEH 35 – – ns

Input valid to CE# HIGH tDS tDVEH 30 – – ns 1

CE# HIGH to input transition tDH tEHDX 0 – – ns

CE# HIGH to WE# HIGH tWH tEHWH 0 – – ns

CE# HIGH to CE# LOW tCPH tEHEL 20 – – ns

Address valid to CE# LOW tAS tAVEL 0 – – ns

CE# LOW to address transition tAH tELAX 45 – – ns

OE# HIGH to CE# LOW – tGHEL 0 – – ns

VHH rise or fall time on VPP/WP# – tVHVPP 250 – – ns

Program/erase valid to RY/BY# LOW tBUSY tWHRL – – 90 ns 2

WE# HIGH to OE# valid – tWHQV tAVQV +

– – ns

Notes: 1. The user's write timing must comply with this specification. Any violation of this write

timing specification may result in permanent damage to the NOR Flash device.

2. Sampled only; not 100% tested.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Write AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 69 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 21: CE#-Controlled Program AC Timing

555h PA PA

3rd Cycle 4th Cycle Data Polling

tWC

tAS

tCP

tDS

tWHWH1

tCPH

tAH

tWS

tGHEL

tDH

tWH

A[MAX:0]

WE#

OE#

CE#

DQ[15:0] A0h PD DQ7# DOUT

Notes: 1. Only the third and fourth cycles of the PROGRAM command are represented. The PRO-

GRAM command is followed by checking of the status register data polling bit.

2. PA is the address of the memory location to be programmed. PD is the data to be pro-

grammed.

3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit

[DQ7]).

4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

5. For tWHWH1 timing details, see the Program/Erase Characteristics table.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Write AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 70 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 22: Chip/Block Erase AC Timing

555h

tWC

tAS

tWP

tDS

tWPH

tAH

tCS

tGHWL

tDH

tCH

A[MAX:0]

CE#

OE#

WE#

DQ[15:0] AAh

2AAh 555h 555h

BAh1

2AAh555h

55h 55hAAh80h 10h/

30h

Notes: 1. For a CHIP ERASE command, the address is 555h, and the data is 10h; for a BLOCK ERASE

command, the address is BAd, and the data is 30h.

2. BAd is the block address.

3. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

4. For tWHWH1 timing details, see the Program/Erase Characteristics table.

Figure 23: Accelerated Program AC Timing

tVHVPP

VHH

VIL or VIH

VPP/WP#

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Write AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 71 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Data Polling/Toggle AC Characteristics

Table 35: Data Polling/Toggle AC Characteristics

Note 1 applies to entire table

Parameter

Symbol

Min Max UnitLegacy JEDEC

Address setup time to CE# or OE# LOW tASO tAXGL 15 – ns

Address hold time from OE# or CE# HIGH tAHT tGHAX, tEHAX 0 – ns

CE# HIGH time tEPH tEHEL2 20 – ns

OE# HIGH time tOPH tGHGL2 20 – ns

WE# HIGH to OE# LOW (toggle and data polling) tOEH tWHGL2 10 – ns

Note: 1. Sampled only; not 100% tested.

Figure 24: Data Polling AC Timing

DQ7#Data DQ7# Valid DQ7

Data

Output flagData Output flag

Valid

DQ[6:0] Data

tHZ/tDF

tCE

tOE tOPH

tCH

tBUSY

tOEH

CE#

OE#

WE#

DQ[6:0]

DQ7

RY/BY#

Notes: 1. DQ7 returns a valid data bit when the PROGRAM or ERASE command has completed.

2. See the following tables for timing details: Read AC Characteristics and Data Polling/

Toggle AC Characteristics.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Data Polling/Toggle AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 72 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 25: Toggle/Alternative Toggle Bit Polling AC Timing

Toggle Toggle ToggleData

Stop

toggling

Output

Valid

tBUSY

tOPH tEPH

tOEH

CE#

WE#

OE#

DQ6/DQ2

RY/BY#

tOPH

tAHT tASO

tAHT

tDH

tASO

A[MAX:0]

tOE tCE

Notes: 1. DQ6 stops toggling when the PROGRAM or ERASE command has completed. DQ2 stops

toggling when the CHIP ERASE or BLOCK ERASE command has completed.

2. See the following tables for timing details: Read AC Characteristics and Data Polling/

Toggle AC Characteristics.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Data Polling/Toggle AC Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 73 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Program/Erase Characteristics

Table 36: Program/Erase Characteristics

Notes 1 and 2 apply to entire table

Parameter

Buffer

Size Byte Word Min Typ Max Unit Notes

Erase

Block erase (128KB) – – – – 200 1100 ms –

Chip erase – – – – 208 – s –

Erase suspend latency time – – – – – 20 µs –

Erase or erase resume to suspend – – – – 100 – µs 3, 4

Accelerated chip erase – – – – 190 – s –

Program

Single-word program – – – – 25 200 µs –

Buffer Program

Word write to buffer program (tWHWH1) 32 – 32 – 92 460 µs –

64 – 64 – 117 600 µs –

128 – 128 – 171 900 µs –

256 – 256 – 285 1500 µs –

512 – 512 – 512 2000 µs –

Effective write to buffer program per word

(tWHWH1)

32 – 1 – 2.88 14.38 µs –

64 – 1 – 1.83 9.38 µs –

128 – 1 – 1.34 7.03 µs –

256 – 1 – 1.11 5.86 µs –

512 – 1 – 1.0 3.90 µs –

Accelerated full buffer program time – – – – 410 – µs –

Program suspend latency time – – – – – 15 µs –

Nonvolatile protection

Set nonvolatile protection bit time – – – – 25 320 µs –

Clear nonvolatile protection bit time – – – – 80 1100 ms –

Blank Check, CRC, and Program/Erase Endurance

Blank check: main block – – – – 3.2 – ms –

CRC check time: main block – – – – 5 – ms –

CRC check time: full chip (512Mb) – – – – 5 – s –

PROGRAM/ERASE cycles (per block) – – – 100,000 – – cycles –

Notes: 1. Typical values measured at room temperature and nominal voltages (VCC = 3V).

2. Typical and maximum values are sampled, but not 100% tested.

3. Erase to suspend is the time between an initial BLOCK ERASE or ERASE RESUME com-

mand and a subsequent ERASE SUSPEND command.

4. This typical value allows an ERASE operation to progress to completion--it is important

to note that the algorithm might never finish if the ERASE operation is always suspen-

ded less than this specification.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Program/Erase Characteristics

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 74 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Package Dimensions

Figure 26: 56-Pin TSOP – 14mm x 20mm (Package Code: JS)

Detail A

Seating plane

0.6 ±0.1

0.25 Gage plane

0.1 ±0.05

For reference

only

Pin A1 ID

0.1 A

See Detail A

56X 0.1 ±0.05

0.15 ±0.05

56X 0.22 ±0.05 14 ±0.1

18.4 ±0.1

20 ±0.2

1.1 ±0.1

0.5 TYP

16.2 CTR

11.8

CTR

2X Ø1.2

Notes: 1. All dimensions are in millimeters.

2. Pin A1 ID diameter is 1mm.

3. New package assembly site has effected an ASE process change (original ASE process is

Amkor). The package shows two eject pins on the package mark: one in the corner by

pin 56 and one in the corner by pin 28, each with diameter 2mm x 1.2mm.

4. Package width and length include mold flash.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Package Dimensions

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 75 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 27: 64-Ball LBGA – 11mm x 13mm (Package Code: PC)

0.44 MIN

1.3 ±0.1

7 CTR

11 ±0.1

1 TYP

13 ±0.1

1.0 TYP

Ball A1 ID

Seating plane

0.08 AA

64X Ø0.60

Dimensions apply

to solder balls post-

reflow on Ø0.50 SMD

ball pads.

7 CTR

234567 18

Note: 1. All dimensions are in millimeters.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Package Dimensions

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 76 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Revision History

Rev. H –05/18

• Added Important Notes and Warnings section for further clarification aligning to in-

dustry standards

Rev. G – 11/16

• Updated 56-pin dimension drawing

• Added Note 4 to 56-pin dimension drawing

Rev. F – 6/16

• Updated Table 21: CFI Query System Interface Information in Common Flash Inter-

face

Rev. E – 9/15

• Updated Table 31: Read AC Characteristics – tPAGE in Read AC Characteristics

Rev. D – 01/15

• Promoted the document from Preliminary to Production status

Rev. C – 12/14

• Updated Figure 4: 64-Ball LBGA in Signal Assignments

• Updated Table 21: CFI Query System Interface Information in Common Flash Inter-

face

• Updated Table 23: Primary Algorithm-Specific Extended Query Table in Common

Flash Interface

• Updated Table 28: Input/Output Capacitance in Absolute Ratings and Operating Con-

ditions

• Updated Table 29: DC Current Characteristics in DC Characteristics

• Updated Table 31: Read AC Characteristics – VCC = VCCQ = 2.7-3.6Vin Read AC Charac-

teristics

• Updated Table 32: Read AC Characteristics – VCCQ = 1.65V - VCC in Read AC Character-

istics

• Updated Table 36: Program/Erase Characteristics in Program/Erase Characteristics

Rev. B – 07/14

• Preliminary status

Rev. A – 05/14

• Initial release

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Revision History

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 77 Micron Technology, Inc. reserves the right to change products or specifications without notice.

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000

www.micron.com/products/support Sales inquiries: 800-932-4992

Micron and the Micron logo are trademarks of Micron Technology, Inc.

All other trademarks are the property of their respective owners.

This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.

Although considered final, these specifications are subject to change, as further product development and data characterization some-

times occur.

1Gb: x16, 3V, MT28FW, Automotive Parallel NOR

Revision History

CCMTD-1725822587-3365

mt28fw_genB_1gb_auto.pdf - Rev. H 05/18 EN 78 Micron Technology, Inc. reserves the right to change products or specifications without notice.