FCAS50SN60 Smart Power Module for SRM Features General Description * Very low thermal resistance due to using DBC FCAS50SN60 is an advanced smart power module for SRM drive that Fairchild has newly developed and designed to provide very compact and high performance SRM motor drives mainly targeting low-power inverter-driven SRM application especially for a vacuum air cleaner. It combines optimized circuit protection and drive matched to low-loss IGBTs. System reliability is further enhanced by the integrated under-voltage lock-out and short-circuit protection. The high speed built-in HVIC provides opto-coupler-less IGBT gate driving capability that further reduce the overall size of the inverter system design. In addition the incorporated HVIC facilitates the use of single-supply drive topology enabling the FCAS50SN60 to be driven by only one drive supply voltage without negative bias. Each phase current of inverter can be monitored separately due to the divided negative dc terminals. * 600V-50A single-phase asymmetric bridge IGBT converter for SRM drive including control ICs for gate driving and protection * Divided negative dc-link terminals for inverter current sensing applications * Single-grounded power supply due to built-in HVIC * Switching frequency of 2.2~8kHz * Isolation rating of 2500Vrms/min. Applications * AC 200V ~ 242V single-phase SRM drives for home application vacuum cleaner. Top View Bottom View 44 mm 26.8 mm Figure 1. (c)2006 Fairchild Semiconductor Corporation FCAS50SN60 Rev. A 1 www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM September 2006 FCAS50SN60 Smart Power Module for SRM Integrated Power Functions * 600V-50A IGBT asymmetric converter for single-phase SRM drives (Please refer to Figure 3) Integrated Drive, Protection and System Control Functions * For high-side IGBTs: Gate drive circuit, High voltage isolated high-speed level shifting Control circuit under-voltage (UV) protection Note) Available bootstrap circuit example is given in Figures 10. * For low-side IGBTs: Gate drive circuit, Short circuit protection (SC) Control supply circuit under-voltage (UV) protection * Fault signaling: Corresponding to a UV fault (Low-side supply) * Input interface: 5V CMOS/LSTTL compatible, Schmitt trigger input Pin Configuration Top View (1) VCC(L) (2) COM (3) NC (4) NC (5) IN(L) (6) VFO (7) CFOD (8) CSC (9) G(L) (10) E(L) (11) NC (12) NC (13) IN(H) (14) VCC(H) (15) VB (21) NB2 (22) NC (23) NB1 (24) NA Case Temperature (TC) Detecting Point (25) B DBC (16) VS (17) G(H) (18) E(H) (26) A (19) R(TH) (27) P (20) V(TH) Figure 2. 2 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Pin Descriptions Pin Number Pin Name Pin Description 1 VCC(L) Low-side Common Bias Voltage for IC and IGBTs Driving 2 COM Common Supply Ground 3 NC Dummy Pin 4 NC Dummy Pin 5 IN(L) Signal Input for Low-side IGBT 6 VFO Fault Output 7 CFOD Capacitor for Fault Output Duration Time Selection 8 CSC Capacitor (Low-pass Filter) for Short-Current Detection 9 G(L) Gate terminal of low-side IGBT 10 E(L) Emitter terminal of low-side IGBT 11 NC Dummy Pin 12 NC 13 IN(H) Dummy Pin 14 VCC(H) 15 VB High-side Bias Voltage for Gate Driving 16 VS High-side Bias Voltage Ground for Gate Driving 17 G(H) Gate terminal of the High-side IGBT 18 E(H) Emitter terminal of the High-side IGBT 19 R(TH) Thermistor Series Resistor 20 V(TH) Thermistor Bias Voltage 21 NB2 Negative DC-Link Input for B Leg (Should be shorted with NB1 externally) Signal Input for High-side IGBT High-side Bias Voltage 22 NC Dummy Pin 23 NB1 Negative DC-Link Input for B Leg (Should be shorted with NB2 externally) 24 NA Negative DC-Link Input for A Leg 25 B Output for B Leg 26 A Output for A Leg 27 P Positive DC-Link Input 3 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Internal Equivalent Circuit and Input/Output Pins (20) V(TH) (19) R(TH) (15) VB (14) VCC(H) (13) IN(H) (16) VS P (27) VB VCC COM IN OUT VS A (26) (17) G(H) (18) E(H) (12) NC B (25) (11) NC (8) CSC (7) CFOD (6) VFO (5) IN(L) C(SC) OUT(UL) C(FOD) VFO IN(WL) OUT(VL) NA (24) (4) NC IN(VL) (3) NC IN(UL) (2) COM COM(L) (1) VCC(L) OUT(WL) VCC NB1 (23) (9) G(L) NC (22) (10) E(L) NB2 (21) Note: 1. The low-side is composed of one IGBT and freewheeling diode and one control IC which has gate driving and protection functions. 2. The power side is composed of four dc-link input terminals and two output terminals. 3. The high-side is composed of one IGBT and freewheeling diode and one drive IC for high-side IGBT. Figure 3. 4 FCAS50SN60 Rev. A www.fairchildsemi.com Unless Otherwise Specified) Inverter Part Symbol Parameter VPN(Surge) Conditions Supply Voltage (Surge) Applied between P- NA, NB1, NB2 Collector-emitter Voltage Rating Units 550 V 600 V IC Each IGBT Collector Current TC = 25C 50 A ICP VCES Each IGBT Collector Current (Peak) TC = 25C, Under 1ms Pulse Width 100 A PC Collector Dissipation TC = 25C per One IGBT 110 W TJ Operating Junction Temperature (Note 1) -20 ~ 125 C Note: 1. The maximum junction temperature rating of the power chips integrated within the module is 150 C(@TC 100C). However, to insure safe operation, the average junction temperature should be limited to TJ(ave) 125C (@TC 100C) Control Part Symbol Parameter Conditions VCC Control Supply Voltage Applied between VCC(H), VCC(L) - COM VBS High-side Control Bias Voltage Applied between VB - VS VIN Input Signal Voltage Applied between IN(H), IN(L) - COM VFO Fault Output Supply Voltage Applied between VFO - COM IFO Fault Output Current Sink Current at VFO Pin VSC Current Sensing Input Voltage Applied between CSC - COM Rating Units 20 V 20 V -0.3~5.5 V -0.3~VCC+0.3 V 5 mA -0.3~VCC+0.3 V Total System Symbol VPN(PROT) Parameter Self Protection Supply Voltage Limit (Short Circuit Protection Capability) Conditions Rating Units 400 V VCC = VBS = 13.5 ~ 16.5V TJ = 125C, Non-repetitive, less than 6s Module Case Operation Temperature -20 ~ 95 C TSTG Storage Temperature -40 ~ 125 C VISO Isolation Voltage 2500 Vrms TC 60Hz, Sinusoidal, AC 1 minute, Connection Pins to DBC Thermal Resistance Symbol Rth(j-c)Q Rth(j-c)F Parameter Junction to Case Thermal Resistance Conditions Min. Typ. Max. Units Each IGBT under Operating Condition - - 0.90 C/W Each FWDi under Operating Condition - - 2.2 C/W Note: 2. For the measurement point of case temperature (TC), please refer to Figure 2. 5 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Absolute Maximum Ratings (TJ = 25C, Inverter Part Symbol VCE(SAT) VFM HS tON Parameter Conditions Typ. Max. Units Collector-Emitter Saturation Voltage VCC = VBS = 15V VIN = 5V IC = 50A, TJ = 25C - 1.6 2.3 V FWDi Forward Voltage VIN = 0V IC = 50A, TJ = 25C - 2.1 3.0 V Switching Times VPN = 300V, VCC = VBS = 15V IC = 50A VIN = 0V 5V, Inductive Load RE(H) = 10 (Note 3) tC(ON) tOFF tC(OFF) trr LS Min. VPN = 300V, VCC = VBS = 15V IC = 50A VIN = 0V 5V, Inductive Load (Note 3) tON tC(ON) tOFF - 0.8 - s - 0.6 - s - 1.5 - s - 0.8 - s - 0.08 - s - 1.1 - s - 0.9 - s - 1.5 - s tC(OFF) - 0.8 - s trr - 0.05 - s - - 250 A ICES Collector - Emitter Leakage Current VCE = VCES Note: 3. tON and tOFF include the propagation delay time of the internal drive IC. tC(ON) and tC(OFF) are the switching time of IGBT itself under the given gate driving condition internally. For the detailed information, please see Figure 4. 1 0 0 % IC trr V CE IC IC V IN V IN tO N tO F F tC (O N ) V IN (O N ) V CE 1 0 % IC tC (O F F ) V IN (O F F ) 9 0 % IC 1 0 % V C E 10 % V CE 1 0 % IC Figure 4. Switching Time Definition 6 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Electrical Characteristics (TJ = 25C, Unless Otherwise Specified) Control Part Symbol IQCCL Parameter Quiescent VCC Supply Current IQCCH Conditions Typ. VCC(L) - COM - - 40 mA VCC = 15V IN(H) = 0V VCC(H) - COM - - 80 A VB - V S - - 100 A 4.5 - - V Quiescent VBS Supply Current VBS = 15V IN(H) = 0V VFOH Fault Output Voltage VSC = 0V, VFO Circuit: 4.7k to 5V Pull-up VSC(ref) Short Circuit Trip Level VCC = 15V (Note 4) UVCCD Supply Circuit UnderVoltage Protection Reset Level VSC = 1V, VFO Circuit: 4.7k to 5V Pull-up VFOL Max. Units VCC = 15V IN(L) = 0V IQBS UVCCR Min. Detection Level UVBSD Detection Level UVBSR Reset Level - - 0.8 V 0.45 0.5 0.55 V Applied between VCC(L) - COM 10.5 - 12.5 V 11.0 - 13 V Applied between VB - V S 10.0 - 12.5 V 10.5 - 13.0 V 1.4 1.8 2.0 ms Applied between IN(H), IN(L) - COM 3.0 - - V - - 0.8 V Applied between IN(H), IN(L) - COM 0.9 - 2.2 mA tFOD Fault-out Pulse Width CFOD = 33nF (Note 5) VIH ON Threshold Voltage Logic`1' input voltage VIL OFF Threshold Voltage Logic`0' input voltage Input Bias Current IN(H) = 5V 0.9 - 2.4 mA Resistance of Thermistor @ TC = 25C (Note Fig. 10) - 50 - k @ TC = 80C (Note Fig. 10) - 5.76 - k IINH(ON) IN(L) = 5V IINL(ON) RTH Note: 4. Short-circuit current protection is functioning only at the low-sides. 5. The fault-out pulse width tFOD depends on the capacitance value of CFOD according to the following approximate equation : CFOD = 18.3 x 10-6 x tFOD[F] Recommended Operating Conditions Symbol Parameter Conditions Value Min. Typ. Max. Units VPN Supply Voltage Applied between P - NA, NB1, NB2 - 300 450 V VCC Control Supply Voltage Applied between VCC(H), VCC(L) - COM 13.5 15 16.5 V VBS High-side Bias Voltage Applied between VB - VS 13.5 15 18.5 V fPWM PWM Input Signal TC 100C, TJ 125C - 3 - kHz VIN(ON) Input ON Voltage Applied between IN(H), IN(L) - COM 4 ~ 5.5 V VIN(OFF) Input OFF Voltage Applied between IN(H), IN(L) - COM 0 ~ 0.65 V 7 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Electrical Characteristics (TJ = 25C, Unless Otherwise Specified) Parameter Mounting Torque Surface Flatness Limits Conditions Mounting Screw - M3 Units Min. Typ. Max. 5.17 6.29 7.30 Kg*cm 0.51 0.62 0.72 N*m 0 - 120 um - 15.0 - g Note Figure 5. Weight (+) (+) (+) Figure 5. Flatness Measurement Position 8 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Mechanical Characteristics and Ratings FCAS50SN60 Smart Power Module for SRM Time Charts of Protective Function Input Signal Protection Circuit State RESET SET RESET UV CCR a1 Control Supply Voltage a6 UV CCD a3 a2 a4 a7 Output Current a5 Fault Output Signal a1 : Control supply voltage rises: After the voltage rises UVCCR, the circuits start to operate when next input is applied. a2 : Normal operation: IGBT ON and carrying current. a3 : Under voltage detection (UVCCD). a4 : IGBT OFF in spite of control input condition. a5 : Fault output operation starts. a6 : Under voltage reset (UVCCR). a7 : Normal operation: IGBT ON and carrying current. Fig. 6. Under-Voltage Protection (Low-side) Input Signal Protection Circuit State RESET SET RESET UV BSR Control Supply Voltage b5 b1 UV BSD b2 b3 b4 b6 Output Current High-level (no fault output) Fault Output Signal b1 : Control supply voltage rises: After the voltage reaches UVBSR, the circuits start to operate when next input is applied. b2 : Normal operation: IGBT ON and carrying current. b3 : Under voltage detection (UVBSD). b4 : IGBT OFF in spite of control input condition, but there is no fault output signal. b5 : Under voltage reset (UVBSR) b6 : Normal operation: IGBT ON and carrying current Fig. 7. Under-Voltage Protection (High-side) 9 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM P5 In p u t S ig n a l P6 In te r n a l IG B T G a te -E m itte r V o lta g e S C D e te c tio n P1 P4 P7 O u tp u t C u r re n t P2 S C R e fe r e n c e V o lta g e (0 .5 V ) S e n s in g V o lta g e R C F ilte r D e la y F a u lt O u tp u t S ig n a l P8 P3 (with the external shunt resistance and CR connection) c1 : Normal operation: IGBT ON and carrying current. c2 : Short circuit current detection (SC trigger). c3 : Hard IGBT gate interrupt. c4 : IGBT turns OFF. c5 : Fault output timer operation starts: The pulse width of the fault output signal is set by the external capacitor CFO. c6 : Input "L" : IGBT OFF state. c7 : Input "H": IGBT ON state, but during the active period of fault output the IGBT doesn't turn ON. c8 : IGBT OFF state Fig. 8. Short-Circuit Current Protection (Low-side Operation only) R-T Graph 120 Resistance [k] 100 80 60 40 20 0 20 30 40 50 60 70 80 90 100 110 120 130 Temperature [C] Fig. 9. R-T Curve of the Built-in Thermistor 10 FCAS50SN60 Rev. A www.fairchildsemi.com RPF= 4.7k SRM Module IN(H) CPU IN(L) 100 VFO CPF= 1nF 1nF COM Note: 1. RC coupling at each input (parts shown dotted) might change depending on the PWM control scheme used in the application and the wiring impedance of the application's printed circuit board. The input signal section integrates 3.3k(typ.) pull-down resistor. Therefore, when using an external filtering resistor, please pay attention to the signal voltage drop at input terminal. 2. The logic input is compatible with standard CMOS or LSTTL outputs. Figure 10. Recommended CPU I/O Interface Circuit This Value depends on PWM Control Algorithm 15V-Line RE(H)=10 R BS D BS SRM module P 25 18uF 0.1uF Vcc VB IN HO COM VS Outputs Vcc 1000uF 1uF IN OUT COM V SL NA NB Note: It would be recommended that the bootstrap diode, DBS, has soft and fast recovery characteristics. RBS should be 2.5 times greater than RE(H) Figure 11. Recommended Bootstrap Operation Circuit and Parameters 11 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM 5V-Line FCAS50SN60 Smart Power Module for SRM RE(H) 15V line (20) V(TH) (19) R(TH) RBS DBS (15) VB (14) VCC(H) CBS Gating AH CBSC (13) IN(H) (16) VS P (27) VB VCC COM IN OUT VS A (26) (17) G(H) (18) E(H) M C P U (12) NC RF RS B (25) (11) NC (8) CSC CSC RPF (7) CFOD CFOD Fault 5V line (6) VFO (5) IN(L) Gating BL C(SC) OUT(UL) CDCS C(FOD) VFO IN(WL) OUT(VL) NA (24) (4) NC IN(VL) (3) NC IN(UL) (2) COM CBPF COM(L) CPL CPF (1) VCC(L) CSP15 OUT(WL) VCC NB1 (23) CSPC15 (9) G(L) NC (22) (10) E(L) NB2 (21) Input Signal for Short-Circuit Protection Note: 1. To avoid malfunction, the wiring of each input should be as short as possible. (less than 2-3cm) 2. By virtue of integrating an application specific type HVIC inside the Module, direct coupling to CPU terminals without any opto-coupler or transformer isolation is possible. 3. VFO output is open collector type. This signal line should be pulled up to the positive side of the 5V power supply with approximately 4.7k resistance. Please refer to Figure 10. 4. CSP15 of around 7 times larger than bootstrap capacitor CBS is recommended. 5. VFO output pulse width should be determined by connecting an external capacitor(CFOD) between CFOD(pin7) and COM(pin2). (Example : if CFOD = 33 nF, then tFO = 1.8ms (typ.)) Please refer to the note 6 for calculation method. 6. Input signal is High-Active type. There is a 3.3k resistor inside the IC to pull down each input signal line to GND. When employing RC coupling circuits, set up such RC couple that input signal agree with turn-off/turn-on threshold voltage. 7. To prevent errors of the protection function, the wiring around RSC, RF and CSC should be as short as possible. 8. In the short-circuit protection circuit, please select the RFCSC time constant in the range 3~4 s. 9. Each capacitor should be mounted as close to the pins as possible. 10. To prevent surge destruction, the wiring between the smoothing capacitor and the P&N pins should be as short as possible. The use of a high frequency non-inductive capacitor of around 0.1~0.22 F between P and N pins is recommended. 11. Relays are used at almost every systems of electrical equipments of home appliances. In these cases, there should be sufficient distance between the CPU and the relays. 12. CSPC15 should be over 1uF and mounted as close to the pins of the module as possible. 13. NB1(pin23) and NB2(pin21) should be shorted externally. Fig. 12. Application Circuit 12 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Detailed Package Outline Drawings 13 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Detailed Package Outline Drawings (Continued) 14 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM Detailed Package Outline Drawings (Continued) 15 FCAS50SN60 Rev. A www.fairchildsemi.com The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACExTM ActiveArrayTM BottomlessTM CoolFETTM CROSSVOLTTM DOMETM EcoSPARKTM E2CMOSTM EnSignaTM FACTTM FACT Quiet SeriesTM FAST(R) FASTrTM FPSTM FRFETTM GlobalOptoisolatorTM GTOTM HiSeCTM I2CTM i-LoTM ImpliedDisconnectTM Across the board. Around the world.TM The Power Franchise(R) Programmable Active DroopTM ISOPLANARTM LittleFETTM MICROCOUPLERTM MicroFETTM MicroPakTM MICROWIRETM MSXTM MSXProTM OCXTM OCXProTM OPTOLOGIC(R) OPTOPLANARTM PACMANTM POPTM Power247TM PowerEdgeTM PowerSaverTM PowerTrench(R) QFET(R) QSTM QT OptoelectronicsTM Quiet SeriesTM RapidConfigureTM RapidConnectTM SerDesTM SILENT SWITCHER(R) SMART STARTTM SPMTM StealthTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SyncFETTM TinyLogic(R) TINYOPTOTM TruTranslationTM UHCTM UltraFET(R) UniFETTM VCXTM DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I14 16 FCAS50SN60 Rev. A www.fairchildsemi.com FCAS50SN60 Smart Power Module for SRM TRADEMARKS