QPC1022 Broad Band Low Distortion SPDT Switch (R) General Description The QPC1022 is a single pole dual-throw (SPDT) switch designed for switching applications requiring very low insertion loss and high power handling capability with minimal DC power consumption. The excellent linearity performance achieved by the QPC1022 makes it ideal for 9 Pin 1.1x1.5mm LGA Package use in cellular base. This switch offers very high isolation between RF ports providing greater separation between transmit and receive paths. The QPC1022 is packaged in a very compact 1.1mm x 1.5mm x 0.375mm (typical) 9-Pin LGA package. Product Features * 5MHz to 6GHz Operation * Low Insertion Loss: 0.25dB at 2GHz * Harmonics: 2fo of -106dBc at 1980MHz 3fo of -94dBc at 1980MHz * High Isolation: 56dB at 204MHz 39dB at 2GHz * High IP3: 76 dBm at 1.9GHz Functional Block Diagram * Compatible with Low Voltage Logic (VHIGH Minimum = 1.3V) * No External DC Blocking Capacitors Required on RF Paths Unless DC is Applied Externally QPC1022 RF1612 * 1000V HBM ESD Rating on All Ports RF1 ANT Applications RF2 * Cellular BTS * Post PA Switching CTRL EN VDD * General Purpose Switching Applications Ordering Information Data Sheet Rev E. August 16, 2018 | Subject to change without notice 1 of 9 Part No. Description QPC1022SB Sample Bag with 5 pieces QPC1022SR Sample Reel with 100 pieces QPC1022TR7 Standard 7" Reel with 2,500 pieces QPC1022PCK401 Fully Assembled 50 Ohm Evaluation Board and Sample Bag with 5 pieces www.qorvo.com QPC1022 Broad Band Low Distortion SPDT Switch (R) Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature (Tcase) Recommended Operating Conditions Rating -40 to +150C -40 to 105C Parameter Min Typ Max Device Voltage (Vdd) +2.4 TCASE -40 +5 Units +5.8 V +105 C +125 C Maximum Vdd 6.0 V Tj Maximum EN 3.0 V RF input Power 5MHz @ 85C 33 dBm Maximum CTRL 3.0 V RF input power >20MHz @ 85C 37 dBm Max Input Power at 105C 33 dBm : 5MHz Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. 37 dBm : >20MHz Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Electrical Specifications Parameter Conditions(1) Min Operational Frequency Range Insertion Loss RF1/RF2 to ANT Isolation RF1 to RF2 RF Port Return Loss (ANT, RF1, RF2) Harmonics 2fo Harmonics 3fo Typ 5 Max Units 6000 MHz 5.0MHz to 1.0GHz 0.2 0.4 dB 1GHz to 2.0GHz 0.25 0.4 dB 2.0GHz to 2.5GHz 0.26 dB 2.5GHz to 3.5GHz 0.35 dB 3.5GHz to 3.8GHz 0.38 dB 3.8GHz to 6GHz 0.46 dB 56 dB 5.0MHz to 200MHz 200MHz to 1.0GHz 39 46 dB 1.0GHz to 2.0GHz 32 39 dB 2.0GHz to 2.5GHz 36 dB 2.5GHz to 3.5GHz 34 dB 3.5GHz to 3.8GHz 33 dB 3.8GHz to 6GHz 29 dB 5.0MHz to 1.0GHz 31 dB 1GHz to 2.0GHz 23 dB 2.0GHz to 2.5GHz 22 dB 2.5GHz to 3.5GHz 18 dB 3.5GHz to 3.8GHz 17.5 dB 3.8GHz to 6GHz 14.5 dB RFin = 35dBm, 915MHz -109 dBc RFin = 33dBm, 1980MHz -106 RFin = 35dBm, 915MHz -98 RFin = 33dBm, 1980MHz -94 -80 dBc dBc -80 dBc Notes: 1. Test conditions unless otherwise noted: VDD = +5.0V, Temp=+25C, 50 system. Data Sheet Rev E. August 16, 2018 | Subject to change without notice 2 of 9 www.qorvo.com QPC1022 Broad Band Low Distortion SPDT Switch (R) Electrical Specifications Parameter Conditions(1) OIP2 RFx to ANT (5MHz) Tone 1: 5MHz at 10dBm Tone 2: 4.95MHz at 10dBm 103 dBm OIP2 RFx to ANT(450MHz) Tone 1: 450MHz at 10dBm Tone 2: 445.5MHz at 10dBm 131 dBm OIP2 RFx to ANT Tone 1: 2480MHz at 10dBm Tone 2: 2690MHz at 10dBm 132 dBm OIP3 RFX to ANT (5MHz) Tone 1: 5MHz at 10dBm Tone 2: 4.95MHz at 10dBm Tone 3: 4.85MHz at 10dBm 73 dBm OIP3 RFX to ANT (450MHz) Tone 1: 450MHz at 10dBm Tone 2: 445.5MHz at 10dBm Tone 3: 436.5MHz at 10dBm 73 dBm OIP3 RFX to ANT(850MHz) 30MHz spacing at 20dBm/Tone 76 dBm OIP3 RFX to ANT (1900MHz) 30MHz spacing at 20dBm/Tone 76 dBm Supply Current Idd EN = High EN = Low 52 2 100 5 uA Control Voltage (EN, CTRL) VHigh Vlow 1.8 0 2.75 0.45 V Control Current (EN, CTRL) Ihigh ILow 2.5 0.1 5 3 uA Switching Speed RF ON 50% control to 90% RF ON 2.6 us Switching Speed RF OFF 50% control to 10% RF ON 1.5 us Startup Time from Shutdown Maximum time for switch to reach full compliant operation 6 us Turn on Time Time from Vdd 50% of operational voltage to RF signal at 90% 5 Min 1.3 Typ Max 20 Units us Notes: 1. Test conditions unless otherwise noted: VDD = +5.0V, Temp=+25C, 50 system. Thermal Information Conditions Parameter Thermal Resistance (JC) (1) Channel Temperature, TCH (Under RF) Value Units 37dBm @ 2GHz, 85C Stage Temperature 156 C/W 37dBm@ 2GHz, 85C Stage Temperature 125 C Notes: 1. Thermal Resistance is referenced to back of EVB. Data Sheet Rev E. August 16, 2018 | Subject to change without notice 3 of 9 www.qorvo.com QPC1022 (R) Broad Band Low Distortion SPDT Switch Power-Up, Power-Down sequence and operation controls Sequence for Power UP and Power DOWN from the supply that is connected to QPC1022 VDD pin. Power-up Sequence: 1) Turn on VDD (supply) 2) Then EN 3) Then CTRL 4) Then (20s or greater) 5) Apply RF signal Power-Down Sequence: 1) Turn off RF signal 2) Then CTRL 3) Then EN 4) Turn off VDD (supply) Sequence for going in and out of a mode, keeping the VDD or supply disabling/enabling the QPC1022 by shutdown on, but the EN pin. Power-Up Sequence: 1) Turn-on EN (enable) 2) Then CTRL 3) Then (5s or greater) 4) Turn-on RF signal Power-Down Sequence: 1) Turn-off RF signal 2) Then CTRL 3) Then EN (disable) When changing switch positions RF1 and RF2, no RF signal should to any RF port while the CTRL is states. between be applied changing Switching Ports: 1) Turn-off RF signal 2) Then change CTRL state 3) Then (5s or greater) 4) Turn-on RF signal Control Logic for Valid Operational States State 1 2.4V to 5.8V VDD 2 2.4V to 5.8V CTRL VHIGH VLOW Shutdown 2.4V to 5.8V X Data Sheet Rev E. August 16, 2018 | Subject to change without notice 4 of 9 EN VHIGH VHIGH VLOW RF Path ANT-RF1 ANT-RF2 Shutdown www.qorvo.com QPC1022 (R) Broad Band Low Distortion SPDT Switch Performance Plots - 50 Test conditions unless otherwise noted: VDD = +5V Data Sheet Rev E. August 16, 2018 | Subject to change without notice 5 of 9 www.qorvo.com QPC1022 (R) Broad Band Low Distortion SPDT Switch Evaluation Board Schematic & Layout for 50 Application Bill of Material - QPC1022 - 50 Reference Des. Value Description Manuf. Printed Circuit Board U1 R1, R2, R3 0 Part Number Qorvo QPC1022-411(B) QPC1022 Switch, QFN pkg. Qorvo QPC1022SB Resistor, Chip, 0402 various R4, R5 DNI C2, C3 100pF Cap., Chip, 0402, 5%, 50V. NPO/COG various C1 2200pF Cap, 10%, 50V, X7R, 0402 various J1, J2, J3 CONN, SMA, EL FLT VIPER, MAT-21-1038 P1 CONN, HDR, ST, PLRZD, 5-PIN, 0.100" Data Sheet Rev E. August 16, 2018 | Subject to change without notice 6 of 9 www.qorvo.com QPC1022 Broad Band Low Distortion SPDT Switch (R) Pin Configuration and Description (Top View) RF2 1.5mm 8 GND 1 ANT 2 GND 3 GND 9 7 VDD 6 EN 5 CTRL 4 RF1 1.1mm Pad No. Label 1,3,9 GND Description 2 ANT Single-Ended RF port 4 RF1 Single-Ended RF port 5 CTRL Switch Logic control input 6 EN Shutdown logic control input 7 VDD Supply Voltage 8 RF2 Single-Ended RF port Connect with Low inductive path to ground Data Sheet Rev E. August 16, 2018 | Subject to change without notice 7 of 9 www.qorvo.com QPC1022 (R) Broad Band Low Distortion SPDT Switch Package Marking and Dimensions Marking: Trace Code -XXXX XX XX Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012. 3. Contact plating: NiAu PCB Mounting Pattern Notes: 1. All dimensions are in millimeters. Angles are in degrees. Data Sheet Rev E. August 16, 2018 | Subject to change without notice 8 of 9 www.qorvo.com QPC1022 Broad Band Low Distortion SPDT Switch (R) Handling Precautions Parameter Rating Standard ESD-Human Body Model (HBM) Class 2 ESDA/JEDEC JS-001-2012 ESD-Charged Device Model (CDM) Class C3 JEDEC JESD22-C101F MSL-Moisture Sensitivity Level 2 Caution! ESD-Sensitive Device IPC/JEDEC J-STD-020 Solderability Compatible with both lead-free (260C max. reflow temp.) soldering process. Solder profiles available upon request. Contact plating: Au plating 0.5m, over a 2m Ni Plating RoHS Compliance This part is compliant with EU 2011/65/EU RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment), as amended by Directive 2015/863/EU. This product also has the following attributes: * Lead Free * Halogen Free (Chlorine, Bromine) * * * * * Antimony Free TBBP-A (C15H12Br402) Free PFOS Free SVHC Free Qorvo Green Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations: Tel: 1-844-890-8163 Web: www.qorvo.com Email: customer.support@qorvo.com For technical questions and application information: Email: sjcapplications.engineering@qorvo.com Important Notice The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Copyright 2018 (c) Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc. Data Sheet Rev E. August 16, 2018 | Subject to change without notice 9 of 9 www.qorvo.com