Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Surface Mount
NPCAPTM-PXFSeries
・Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
・Rated voltage range : 2 to 10Vdc, Capacitance range : 120 to 1,000µF
・Case size range :φ5×3.9L toφ8×7.7L
・Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
◆SPECIFICATIONS
Items Characteristics
Category
Temperature Range -55 to +105℃
Rated Voltage Range
2 to 10Vdc
Capacitance Tolerance
±20% (M) (at 20℃, 120Hz)
Surge Voltage Rated voltage×1.15 (at 105℃)
Leakage Current Shall not exceed values shown in STANDARD RATINGS. (at 20℃ after 2 minutes)
Dissipation Factor
(tanδ)0.12 max. (at 20℃, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25 (at 100kHz)
Endurance The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
(E40, E46, F45 : 3,000 hours ) at 105℃.
Appearance No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)≦150% of the initial specified value
ESR ≦150% of the initial specified value
Leakage current ≦The initial specified value
Bias Humidity The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours (E40, E46, F45 : 500 hours ) .
Appearance No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)≦150% of the initial specified value
ESR ≦150% of the initial specified value
Leakage current ≦The initial specified value
Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)≦150% of the initial specified value
ESR ≦150% of the initial specified value
Leakage current ≦The initial specified value
Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
0.3max.
W
P
B
±
0.2
C
±
0.2
A
±
0.2
Terminal Code : A
L
±
0.3 (Note)
Note : L+0.1/-0.2 for E40, E46 and F45
Size Code
F61
F80
H70
H80
6.3
6.3
8
8
L
5.8
7.7
6.7
7.7
A
6.6
6.6
8.3
8.3
B
6.6
6.6
8.3
8.3
C
7.2
7.2
9.0
9.0
W
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
P
1.9
E61 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
1.9
3.1
3.1
φ
D
5
F45 4.4 6.6 6.6 7.2 0.5 to 0.8 1.96.3
E46 4.5 5.3 5.3 5.9 0.5 to 0.8 1.45
E40 3.9 5.3 5.3 5.9 0.5 to 0.8 1.45
◆PART NUMBERING SYSTEM
Supplement code
Size code
Capacitance tolerance code
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 10V:100)
Series code
Category
A P X F A R A GM
1 3 42 6 7 8 9 10 13125 18171611 1514
Please refer to "Product code guide (conductive polymer type)"
Capacitance code (ex. 330µF:331, 1,000µ
Upgrade!
Lower ESR
PXF
PXE P36
◆MARKING
F
69A
390
2.5
V
34 CAT. No. E1001O
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS