BAS21SLT1 Preferred Device Dual Series High Voltage Switching Diode * Moisture Sensitivity Level: 1 * ESD Rating - Human Body Model: Class 1 ESD Rating - Machine Model: Class B http://onsemi.com MAXIMUM RATINGS Rating Symbol Value Unit Continuous Reverse Voltage VR 250 Vdc Peak Forward Current IF 225 mAdc IFM(surge) 625 mAdc Characteristic Symbol Max Unit Total Device Dissipation FR-5 Board (Note 1.) TA = 25C Derate above 25C PD 225 mW Peak Forward Surge Current ANODE 1 CATHODE 2 3 CATHODE/ANODE THERMAL CHARACTERISTICS Thermal Resistance, Junction to Ambient Total Device Dissipation Alumina Substrate, (Note 2.) TA = 25C Derate above 25C mW/C 1.8 3 MARKING DIAGRAM 1 JS M 2 RJA 556 C/W PD 300 mW SOT-23 CASE 318 STYLE 11 JS = Device Code M = Date Code mW/C 2.4 Thermal Resistance, Junction to Ambient RJA 417 C/W Junction and Storage Temperature Range TJ, Tstg -55 to +150 C ORDERING INFORMATION Device BAS21SLT1 Package Shipping SOT-23 3000/Tape & Reel ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Characteristic Symbol Min Max - - 1.0 100 250 - - - 1000 1250 Unit OFF CHARACTERISTICS Reverse Voltage Leakage Current (VR = 200 Vdc) (VR = 200 Vdc, TJ = 150C) Reverse Breakdown Voltage (IBR = 100 Adc) Adc IR V(BR) Preferred devices are recommended choices for future use and best overall value. Vdc Forward Voltage (IF = 100 mAdc) (IF = 200 mAdc) VF mV Diode Capacitance (VR = 0, f = 1.0 MHz) CD - 5.0 pF Reverse Recovery Time (IF = IR = 30 mAdc, RL = 100 ) trr - 50 ns 1. FR-5 = 1.0 0.75 0.062 in. 2. Alumina = 0.4 0.3 0.024 in. 99.5% alumina. Semiconductor Components Industries, LLC, 2001 February, 2001 - Rev. 1 1 Publication Order Number: BAS21SLT1/D BAS21SLT1 820 +10 V 2.0 k 100 H IF tp tr 0.1 F IF t trr 10% t 0.1 F 90% D.U.T. 50 OUTPUT PULSE GENERATOR 50 INPUT SAMPLING OSCILLOSCOPE VR iR(REC) = 3.0 mA IR OUTPUT PULSE (IF = IR = 30 mA; MEASURED at iR(REC) = 3.0 mA) INPUT SIGNAL Notes: 1. A 2.0 k variable resistor adjusted for a Forward Current (IF) of 30 mA. Notes: 2. Input pulse is adjusted so IR(peak) is equal to 30 mA. Notes: 3. tp trr Figure 1. Recovery Time Equivalent Test Circuit 3000 2500 REVERSE CURRENT (nA) FORWARD VOLTAGE (mV) 3500 TA = -55C 2000 1500 TA = 155C 1000 TA = 25C 500 0 0.1 0.2 0.5 1 2 5 10 20 50 100 200 7000 6000 5000 TA = 155C 4000 3000 6 5 4 3 TA = 25C 2 1 0 TA = -55C 1 FORWARD CURRENT (mA) 2 5 10 20 50 REVERSE VOLTAGE (V) Figure 2. Forward Voltage Figure 3. Reverse Leakage http://onsemi.com 2 100 200 300 BAS21SLT1 INFORMATION FOR USING THE SOT-23 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm SOT-23 SOT-23 POWER DISSIPATION SOLDERING PRECAUTIONS The power dissipation of the SOT-23 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT-23 package, PD can be calculated as follows: PD = The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. * Always preheat the device. * The delta temperature between the preheat and soldering should be 100C or less.* * When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10C. * The soldering temperature and time shall not exceed 260C for more than 10 seconds. * When shifting from preheating to soldering, the maximum temperature gradient shall be 5C or less. * After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. * Mechanical stress or shock should not be applied during cooling. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. TJ(max) - TA RJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25C, one can calculate the power dissipation of the device which in this case is 225 milliwatts. PD = 150C - 25C 556C/W = 225 milliwatts The 556C/W for the SOT-23 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 225 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT-23 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. http://onsemi.com 3 BAS21SLT1 PACKAGE DIMENSIONS SOT-23 TO-236AB CASE 318-09 ISSUE AF A L 3 1 V B 2 S DIM A B C D G H J K L S V G C D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIUMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. H K J INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0385 0.0498 0.0140 0.0200 0.0670 0.0826 0.0040 0.0098 0.0034 0.0070 0.0180 0.0236 0.0350 0.0401 0.0830 0.0984 0.0177 0.0236 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.99 1.26 0.36 0.50 1.70 2.10 0.10 0.25 0.085 0.177 0.45 0.60 0.89 1.02 2.10 2.50 0.45 0.60 STYLE 11: PIN 1. ANODE 2. CATHODE 3. CATHODEANODE Thermal Clad is a trademark of the Bergquist Company. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 4 BAS21SLT1/D