Data Sheet October 1, 2009 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Features RoHS Compliant Compatible with RoHS EU Directive 200295/EC (-Z Versions) n Compatible in RoHS EU Directive 200295/EC with lead solder exemption (non -Z versions) n Applications n Distributed Power Architectures n Wireless Networks n Access and Optical Network Equipment n Enterprise Networks n Data processing Equipment n Latest generation IC's (DSP, FPGA, ASIC) and Microprocessor-powered applications. n Delivers up to 10A output current n High efficiency: 95% at 3.3V full load n Small size and low profile: 50.8 mm x 8.10mm x 12.7mm (2.0 in x 0.32 in x 0.5 in) n Light Weight 0.27 oz(7.5 g) n Cost-efficient open frame design n High reliability: MTBF > 10M hours at 25 C n Remote On/Off n Output overcurrent protection with auto-restart n Overtemperature protection n Constant frequency (300 kHz,typical) n Adjustable output voltage 10% of VO (-5% to + 10% for 0.9 V output) n Single-In-Line (SIP) Package n UL* 60950 Recognized, CSA C22.2 No. 60950-00 Certified, and VDE 0805 (IEC60950, 3rd edition) Licensed Options n Remote Sense n Long Pins: 5.08 mm 0.25 mm (0.200 in 0.010 in) Description Austin LynxTM power modules are non-isolated dc-dc converters that can deliver 10 A of output current with full load efficiency of 95% at 3.3 V output. These open frame modules in SIP package enable designers to develop cost-and space efficient solutions. Standard features include remote ON/OFF, output voltage adjustment, overcurrent and overtemperature protection. * ** UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. This product is intended for integration into end-use equipment. All the required procedures for CE marking of end-use equipment should be followed. (The CE mark is placed on selected products.) ISO is a registered trademark of the Internation Organization of Standards Document Name: FDS02-047EPS ver.1.6 PDF Name: Austin Lynx SIP Data Sheet October 1, 2009 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliabiltiy. Device Symbol Min Max Unit Input Voltage: Continuous Parameter All VIN 0 6.5 Vdc Operating Ambient Temperature All TA -40 85 C Storage Temperature All Tstg -55 125 C Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Maximum Input Current (VI = 0 to VI,max; IO = IO,max) Device Symbol Min AXH010A0S0R9 AXH010A0S1R0 AXH010A0P AXH010A0M AXH010A0Y AXH010A0D AXH010A0G AXH010A0F VIN VIN VIN VIN VIN VIN VIN VIN 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.5 Typ II,max Max Unit 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 Vdc Vdc Vdc Vdc Vdc Vdc Vdc Vdc 9.5 A Input Reflected-Ripple Current (5 Hz to 20 MHz; 1 H source impedance; TA = 25 C; CIN = 200 F) 30 mAp-p Input Ripple Rejection (100 - 120Hz) 40 dB CAUTION: This power module is not internally fused. An input line fuse must always be used. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a time-delay fuse with a maximum rating of 20A. Lineage Power 2 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Electrical Specifications (continued) Device Symbol Min Typ Max Unit Output Voltage Set Point (VI = 5V; IO = IO,max; TA = 25 C) Parameter AXH010A0S0R9 AXH010A0S1R0 AXH010A0P AXH010A0M AXH010A0Y AXH010A0D AXH010A0G AXH010A0F VO,set VO,set VO,set VO,set VO,set VO,set VO,set VO,set 0.886 0.985 1.182 1.47 1.764 1.97 2.45 3.234 0.9 1.0 1.2 1.5 1.8 2.0 2.5 3.3 0.914 1.015 1.218 1.53 1.836 2.03 2.55 3.366 Vdc Vdc Vdc Vdc Vdc Vdc Vdc Vdc Output Voltage (Over all operating input voltage, resistive load, and temperature conditions at steady state until end of life.) AXH010A0S0R9 AXH010A0S1R0 AXH010A0P AXH010A0M AXH010A0Y AXH010A0D AXH010A0G AXH010A0F VO VO VO VO VO VO VO VO 0.873 0.970 1.164 1.455 1.746 1.94 2.425 3.2 -- -- -- -- -- -- -- -- 0.927 1.03 1.236 1.545 1.854 2.06 2.575 3.4 Vdc Vdc Vdc Vdc Vdc Vdc Vdc Vdc Output Regulation: Line (VI = VI, min to VI, max) Load (IO = IO, min to IO, max) Temperature (TA = TA, min to TA, max) All All All -- -- -- -- -- -- 0.2 0.4 0.5 Output Ripple and Noise Measured across 10F Tantalum, 1F Ceramic, RMS (5 Hz to 20 MHz bandwidth) Peak-to-peak (5 Hz to 20 MHz bandwidth) All All -- -- -- -- 7 25 15 30 mVrms mVp-p Output Current All IO -- 10 A Output Current-limit Inception (VO = 90% of VO, set) All IO 17 A Output Short-circuit Current (Average) VO = 0.25 V All IO 3 A AXH010A0S0R9 AXH010A0S1R0 AXH010A0P AXH010A0M AXH010A0Y AXH010A0D AXH010A0G AXH010A0F 83 85 86 88 90 91 92 95 % % % % % % % % All fsw Efficiency (VI = VIN, nom; IO = IO, max), TA = 25 C Switching Frequency -- 300 %VO, set %VO, set %VO, set -- kHz General Specifications Parameter Min Calculated MTBF (IO = 100% of IO, max TA = 25 C) Weight Lineage Power Typ Max 10,240,000 -- 6.5(0.23) Unit Hours 7.5(0.27) g (oz.) 3 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min All All Von/off Ion/off -0.7 All All All Von/off Ion/off -- AXH010A0S0R9 All Vtrim Vtrim -5 -10 Overtemperaute Protection (shutdown) All TQ1/TQ2 -- Input Undervoltage Lockout Turn-on Threshold Turn-off Threshold All All 2.63 2.47 Remote On/Off Signal Interface (VI = VI,min to VI, max; open collector pnp or Compatible, Von/off signal referenced to GND. See Figure 20 and Feature Descriptions section) Logic Low (ON/OFF pin open--Module On) Ion/off = 0.0 A Von/off = 0.3 V Logic High (VON/OFF > 2.5 V)--Module Off Ion/off = 1 mA Von/off = 5.5 V Turn-on Time (IO = 80% of IO, max; VO within 1% of steady state; see Figure 12) Output voltage set-point adjustment range (TRIM) Lineage Power Typ Max Unit 0.3 10 V A 6.5 1 V mA ms +10 +10 %VO, set %VO, set 110 -- C 2.8 2.7 2.95 2.9 V V 5 4 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Characteristic Curves The following figures provide typical characteristics curves (TA = 25 C). 92 II, max = 9.5 A 90 10 EFFICIENCY, (%) INPUT CURRENT, II (A) 12 8 6 4 2 88 86 84 82 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 80 78 76 0 2 2.5 3 3.5 4 4.5 INPUT VOLTAGE, VI (V) 5 74 1 5.5 Figure 1. Input Voltage and Current Characteristics at Figure 4. 10A output current. 2 3 4 5 6 7 OUTPUT CURRENT, IO (A) 8 9 10 Converter Efficiency vs Output Current AXH010A0S1R0 (1.0V Output Voltage). 90 EFFICIENCY, (%) NORMALIZED OUTPUT VOLTAGE, VO 92 100% VI VI VI VI 75% = = = = 5.5 V 5.0 V 3.3 V 3.0 V 50% 88 86 84 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 82 80 25% 78 1 2 3 0% 0 3 6 9 12 OUTPUT CURRENT, IO (A) Figure 5. Figure 2. Output Voltage and current characteristics. 94 88 92 EFFICIENCY, (%) 90 EFFICIENCY, (%) 86 84 82 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 80 82 3 4 5 6 7 8 9 Converter Efficiency vs Output Current AXH010A0S0R9(0.9V Output voltage). Lineage Power 9 10 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 1 2 3 4 5 6 7 8 9 10 OUTPUT CURRENT, IO (A) 10 OUTPUT CURRENT, IO (A) Figure 3. 8 Converter Efficiency vs Output Current AXH010A0P (1.2V Output Voltage). 86 76 2 7 88 84 1 6 90 78 74 5 OUTPUT CURRENT, IO (A) 18 15 4 Figure 6. Converter Efficiency vs Output Current AXH010A0M (1.5V Output Voltage). 5 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Characteristic Curves The following figures provide typical characteristics curves at room temperature (TA = 25 C) 97 96.5 92 EFFICIENCY, (%) EFFICIENCY, (%) 94 90 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 88 86 84 1 2 3 4 5 6 7 8 9 AXH010A0Y (1.8V Output Voltage). VI = 4.5 V VI = 5.0 V VI = 5.5 V 94.5 94 1 96 2 3 4 5 6 7 OUTPUT CURRENT, IO (A) 8 9 10 VI = 3.0 V OUTPUT VOLTAGE, VO (V) (20 mV/div) 94 92 90 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 88 2 3 4 5 6 7 8 OUTPUT CURRENT, IO (A) 9 VI = 3.3 V VI = 5.0 V VI = 5.5 V 10 TIME, t (2 s/div) Figure 8. Converter Efficiency vs Output Current Figure 11. Typical Output Ripple Voltage at 10A Output Current. AXH010A0D (2.0V Output Voltage). VIN SOURCE 98 96 94 92 VI = 3.0 V VI = 3.3 V VI = 5.0 V VI = 5.5 V 90 88 1 Figure 9. 2 3 4 5 6 7 OUTPUT CURRENT, IO (A) 8 9 Converter Efficiency vs Output Current AXH010A0G (2.5V Output Voltage). Lineage Power 10 OUTPUT VOLTAGE, VO (V) EFFICIENCY, (%) 95 Figure 10. Converter Efficiency vs Output Current AXH010A0F (3.3V Output Voltage). Figure 7. Converter Efficiency vs Output Current EFFICIENCY, (%) 95.5 93.5 10 OUTPUT CURRENT, IO (A) 86 1 96 TIME, t (2 ms/div) Figure 12. Typical Start-up Transient. 6 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Characteristic Curves OUTPUT CURRENT IO ( 2.5 A/div) OUTPUT CURRENT IO ( 2.5 A/div) OUTPUT VOLTAGE VO (100 mV/div) OUTPUT VOLTAGE VO (100 mV/div) The following figures provide typical characteristics curves at room temperature (TA = 25 C) TIME, t (5 s/div) Figure 13. Typical Transient response to step load change at 2.5 A/s from 100% to 50% of IO,max at 3.3 V Input (Cout =1 F ceramic, 10 F Tantalum). Lineage Power TIME, t (5 s/div) Figure 14. Typical Transient response to step load change at 2.5 A/s from 50% to 100% of IO,max at 3.3 V Input (Cout =1 F ceramic, 10 F Tantalum). 7 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Test Configurations Design Considerations Input Source Impedance TO OSCILLOSCOPE L VI (+) 1 H CS 220 F ESR < 0.1 @ 20 C, 100 kHz BATTERY 2 x 100F Tantalum VI (-) Note: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1H. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 15. Input Reflected Ripple Current Test Setup. To maintain low-noise and ripple at the input voltage, it is critical to use low ESR capacitors at the input to the module. 18 shows the input ripple voltage (mVp-p) for various output models using a 150 F low ESR polymer capacitor (Panasonic p/n: EEFUE0J151R, Sanyo p/n: 6TPE150M) in parallel with 47 F ceramic capacitor (Panasonic p/n: ECJ5YB0J476M, Taiyo Yuden p/n: CEJMK432BJ476MMT). Figure 19 depicts much lower input voltage ripple when input capacitance is increased to 450 F (3 x 150 F) polymer capacitors in parallel with 94 F (2 x 47 F) ceramic capacitor. The input capacitance should be able to handle an AC ripple current of at least: V out V out A rms I rms = I out ----------- 1 - ----------V in V in 200 1F 10 F CERAMIC TANTALUM SCOPE RESISTIVE LOAD GND Note: Scope measurements should be made using a BNC socket, with a 10 F tantalum capacitor and a 1 F ceramic capcitor. Position the load between 51 mm and 76 mm (2 in and 3 in) from the module Figure 16. Peak-to-Peak Output Ripple Measurement Test Setup. CONTACT AND DISTRIBUTION LOSSES VI VO II IO SUPPLY LOAD GND CONTACT RESISTANCE Note: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. 150 100 VI = 5 V VI = 3.3 V 50 0 0.5 1 1.5 2 2.5 OUTPUT VOLTAGE, VO (Vdc) 3 Figure 18. Input Voltage Ripple for Various Output Models, IO = 10 A (CIN = 150 F polymer // 47 F ceramic). 100 INPUT VOLTAGE NOISE (mV p-p) VO INPUT VOLTAGE NOISE (mV p-p) COPPER STRIP 75 50 25 0 0.5 VI = 5 V VI = 3.3 V 1 1.5 2 2.5 OUTPUT VOLTAGE, VO (Vdc) 3 Figure 17. Output Voltage and Efficiency Test Setup. [ V O(+) - V O(-) ] x I O = ------------------------------------------------ x 100 [ V I(+) - V I(-) ] x I I Lineage Power Figure 19. Input Voltage Ripple for Various Output Models, IO = 10 A (CIN = 3x150 F polymer // 2x47 F ceramic). 8 Data Sheet October 1, 2009 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Design Considerations (continued) Input Source Impedance (continued) The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the module. An input capacitance must be placed close to the input pins of the module, to filter ripple current and ensure module stability in the presence of inductive traces that supply the input voltage to the module. Safety Considerations For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL60950, CSA C22.2 No. 60950-00, and VDE 0805:2001-12 (IEC60950, 3rd Ed). For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV),the input must meet SELV requirements. The power module has ELV (extra-low voltage) outputs when all inputs are ELV. The input to these units is to be provided with a maximum 20A time-delay fuse in the unearthed lead. Lineage Power 9 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Feature Descriptions Table 1. Austin LynxTM Trim Values Remote On/Off The Austin LynxTM SIP power modules feature an On/Off pin for remote On/Off operation. If not using the remote On/Off pin, leave the pin open (module will be On). The On/Off pin signal (Von/off) is referenced to ground. To switch the module on and off using remote On/Off, connect an open collector pnp transistor between the On/Off pin and the VI pin (see Figure 20). During a logic-low when the transistor is in the Off state, the power module is On and the maximum Von/off generated by the module is 0.3V. The maximum leakage current of the switch when Von/off = 0.3V and VI = 5.5V (Vswitch = 5.2V) is 10 A. During a logic-high when the transistor is in the active state, the power module is Off. During this state, Von/off = 2.5V to 5.5V and the maximum Ion/ off = 1mA. VO, set Rbuffer 3.3 V 2.5 V 2.0 V 1.8 V 1.5 V 1.2 V 1.0 V 0.9 V 59 kW 78.7 kW 100 kW 100 kW 100 kW 59 kW 30.1 kW 5.11 kW Note: VO, set is the typical output voltage for the unit. For example, to trim-up the output voltage of 1.5V module (AXH010A0M) by 8% to 1.62V, Rtrim-up is calculated as follows: V out = 0.12V R buffer = 100k 24080 R trim - up = --------------- - 100k 0.12 VI Ion/off ON/OFF Vo R trim - up = 100.66k Vswitch AXH010A0M + Von/off VO GND RLOAD TRIM Rtrim-up Figure 20. Remote On/Off Implementation. GND Output Voltage Set-Point Adjustment (Trim) Output voltage set-point adjustment allows the output voltage set point to be increased or decreased by connecting either an external resistor or a voltage source between the TRIM pin and either the VO pin (decrease output voltage) or GND pin (increase output voltage). For TRIM-UP using an external resistor, connect Rtrim-up between the TRIM and GND pins (Figure 21). The value of Rtrim-up defined as: 24080 R trim - up = ------------------ - R buffer V out k |DVout| is the desired output voltage set-point adjustment Rbuffer (internal to the module) is defined in Table 1 for various models. Figure 21. Circuit Configuration to trim-up output voltage. For trim-down using an external resistor, connect Rtrimdown between the TRIM and VOUT pins of the module (Figure 22). The value of Rtrim-down is defined as: V out - 0.8 R trim-down = ------------------------- - 1 x30100 - R buffer V out k Vout is the typical set point voltage of a module |DVout| is the desired output voltage adjustment Rbuffer (internal to the module) is defined in Table 3 for various models For example, to trim-down the output voltage of 2.5 V module (AXH010G) by 8% to 2.3V, Rtrim-down is calculated as follows: V out = 0.2V V out = 2.5V Lineage Power 10 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Feature Descriptions (continued) Output Voltage Set-Point Adjustment (Trim) (continued) R buffer = 78.7k regulating the voltage at the load via the SENSE and GND connections (See 23). The voltage between the SENSE pin and VO pin must not exceed 0.5V. Although both the Remote Sense and Trim features can each increase the output voltage (VO), the maximum increase is not the sum of both. The maximum VO increase is the larger of either the Remote Sense or the Trim. The amount of power delivered by the module is defined as the output voltage multiplied by the output current (VO x IO). When using SENSE and/or TRIM, the output voltage of the module can increase which, if the same output current is maintained, increases the power output by the module. Make sure that the maximum output power of the module remains at or below the maximum rated power. When pin 3 is present but the Remote Sense feature is not being used, leave Sense pin disconnected. 2.5 - 0.8 R trim - down = --------------------- - 1 x30100 - 78700 0.2 R trim - down = 147.05k VO VO VI Rtrim-down SENSE TRIM GND RLOAD DISTRIBUTION LOSSES LOAD DISTRIBUTION LOSSES GND Figure 23. Effective Circuit Configuration for Remote Sense Operation. Figure 22. Circuit Configuration to Decrease Output Voltage. Overcurrent Protection For Trim-up using an external voltage source, apply a voltage from TRIM pin to ground using the following equation: R buffer V trim-up = 0.8 - V out x -----------------30100 To provide protection in a fault condition, the unit is equipped with internal overcurrent protection. The unit operates normally once the fault condition is removed. For Trim-down using an external voltage source, apply a voltage from TRIM pin to ground using the following equation: R buffer V trim-down = 0.8 + V out x -----------------30100 Vtrim-up is the external source voltage for trim-up Vtrim-down is the external source voltage for trim-down |DVout| is the desired output voltage set-point adjustment Rbuffer (internal to the module) is defined in Table 3 for various models If the TRIM feature is not being used, leave the TRIM pin disconnected. The power module will supply up to 170% of rated current for less than 1.25 seconds before it enters thermal shutdown. Overtemperature Protection To provide additional protection in a fault condition, the unit is equipped with a nonlatched thermal shutdown circuit. The shutdown circuit engages when Q1 or Q2 (shown in Figure 24) exceeds approximately 110 C. The unit attempts to restart when Q1 or Q2 cool down and cycles on and off while the fault condition exists. Recovery from shutdown is accomplished when the cause of the overtemperature condition is removed. Remote Sense Austin LynxTM SIP power modules offer an option for a Remote Sense function. When the Device Code description includes a suffix "3", pin 3 is added to the module and the Remote Sense is an active feature. See the Ordering Information at the end of this document for more information. Remote Sense minimizes the effects of distribution losses by Lineage Power 11 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Thermal Considerations Convection Requirements for cooling The power module operates in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation of the unit. Heat is removed by conduction, convection, and radiation to the surrounding environment. The thermal data presented is based on measurements taken in a wind tunnel. The test setup shown in Figure 25 was used to collect data for Figures 26 and 27. Note that the airflow is parallel to the long axis of the module as shown in Figure 24 and derating applies accordingly. To predict the approximate cooling needed for the module, refer to the Power Derating curves in Figures 26 and 27. These derating curves are approximations of the ambient temperatures and airflows required to keep the power module temperature below its maximum rating. Once the module is assembled in the actual system, the module's temperature should be checked as shown in Figure 24 to ensure it does not exceed 110 C. Proper cooling can be verified by measuring the power module's temperature at Q1-pin 6 and Q2-pin 6 as shown in Figure 24. Pin 6 11 Q2 OUTPUT CURRENT IO (A) 10 Q1 Airflow 9 8 7 6 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) 0.5 m/s (100 ft./min.) NATURAL CONVECTION 5 4 3 2 1 0 20 30 40 50 60 70 80 LOCAL AMBIENT TEMPERATURE, TA (C) 90 Figure 24. Temperature Measurement Location . The temperature at either location should not exceed 110 C. The output power of the module should not exceed the rated power for the module (VO, set x IO, max). Figure 26. Typical Power Derating vs output Current for 3.3 Vin. 11 Wind Tunnel 25.4 (1.0) PWBs Power Module OUTPUT CURRENT IO (A) 10 9 8 7 6 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) 0.5 m/s (100 ft./min.) NATURAL CONVECTION 5 4 3 2 1 0 20 30 40 50 60 70 LOCAL AMBIENT TEMPERATURE, TA (C) 80 90 76.2 (3.0) Figure 27. Typical Power Derating vs output Current for 5.0 Vin. x 12.7 (0.50) Air flow Probe Location for measuring airflow and ambient temperature Figure 25. Thermal Test Setup. Lineage Power 12 Data Sheet October 1, 2009 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Through-Hole Lead-Free Soldering Information The RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. They are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Tyco Electronics Power System representative for more details. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Tyco Electronics Board Mounted Power Modules: Soldering and Cleaning Application Note (AP01-056EPS). Solder Ball and Cleanliness Requirements The open frame (no case or potting) power module will meet the solder ball requirements per J-STD-001B. These requirements state that solder balls must neither be loose nor violate the power module minimum electrical spacing. The cleanliness designator of the open frame power module is C00 (per J specification). Lineage Power 13 Data Sheet October 1, 2009 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Outline Diagram for Through-Hole Module Dimensions are in millimeters and (inches). Tolerances: Lineage Power x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in. 0.010 in.) 14 Austin LynxTM SIP Non-Isolated dc-dc Power Modules: 3.0 Vdc - 5.5 Vdc Input, 0.9 Vdc - 3.3 Vdc Output, 10 A Data Sheet October 1, 2009 Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Input Voltage Output Voltage Output Current Efficiency Connector Type Device Code Comcodes 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 4.5 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 3.0 - 5.5 Vdc 4.5 - 5.5 Vdc 0.9 V 1.0 V 1.2 V 1.5 V 1.8 V 2.0 V 2.5 V 3.3 V 1.2 V 1.5 V 1.8 V 2.0 V 2.5 V 3.3 V 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 83% 85% 86% 88% 90% 91% 92% 95% 86% 88% 90% 91% 92% 95% Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole Through-Hole AXH010A0S0R9 AXH010A0S1R0 AXH010A0P AXH010A0M AXH010A0Y AXH010A0D AXH010A0G AXH010A0F AXH010A0PZ AXH010A0MZ AXH010A0YZ AXH010A0DZ AXH010A0GZ AXH010A0FZ 108966250 108966185 108966235 108966227 108966243 108966193 108966219 108966201 CC109106952 CC109106936 CC109101788 CC109106845 CC109101771 CC109104898 Optional features can be ordered using the suffixes shown below. The suffixes follow the last letter of the Product Code and are placed in descending alphanumerical order. Table 2. Device Options Option Remote Sense Long Pins: 5.08 mm 0.25 mm (0.20 in 0.010 in.) RoHS Compliant Suffix 3 5 -Z Asia-Pacific Headquart ers Tel: +65 6 41 6 4283 World Wide Headquarters Lineage Power Corporation 601 Shiloh Road, Plano, TX75074, USA +1-800-526-7819 (Outsid e U.S.A .: +1- 97 2-244-9428) www.line agepower.com e-m ail: techsupport1@linea gepower.com Europe, Middle-East and Afric a He adquarters Tel: +49 898 780 672 80 India Headquarters Tel: +91 8 0 28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC Products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents (c) 2009 Lineage Power Corpor ation, (Plano, Texas) All International Rights Reser ved. Document No: FDS02-047EPS ver.1.6 PDF Name: Austin Lynx SIP