ACT8847 / ACT8849 Rev 10.0, 09-Aug-2018 Advanced PMU for Multi-core Application Processors FEATURES GENERAL DESCRIPTION INTEGRATED POWER SUPPLIES The ACT8847 is a complete, cost effective, and highly-efficient ActivePMUTM power management solution optimized for the power, voltage sequencing and control requirements of Samsung Exynos 4210 (S5PC210/S5PV310) and other application processors. (Please See Ordering Information Section and its Appendix.) Four DC/DC Step-Down (Buck) Regulators 2 x 2.8A, 2 x 1.5A Five Low-Noise LDOs 2 x 150mA, 3 x 350mA Three Low-Input Voltage LDOs The ACT8847 features four fixed-frequency, current-mode, synchronous PWM step-down converters that achieve peak efficiencies of up to 97%. These regulators operate with a fixed frequency of 2.25MHz, minimizing noise in sensitive applications and allowing the use of small external components. These buck regulators supply up to 2.8A of output current and can fully satisfy the power and control requirements of the multi-core application processor. Dynamic Voltage Scaling (DVS) is supported either by dedicated control pins, or through I2C interface to optimize the energy-pertask performance for the processor. This device also include eight low-noise LDOs (up to 350mA per LDO), one always-ON LDO and an integrated backup battery charger to provide a complete power system for the processor. 1 x 150mA, 2 x 350mA One Low IQ Keep-Alive LDO Backup Battery Charger SYSTEM CONTROL AND INTERFACE Six General Purpose I/O with PWM Drivers I2C Serial Interface Interrupt Controller SYSTEM MANAGEMENT Reset Interface and Sequencing Controller Power on Reset Soft / Hard Reset Watchdog Supervision Multiple Sleep Modes The power sequence and reset controller provides power-on reset, SW-initiated reset, and power cycle reset for the processor. It also features the watchdog supervisory function. Multiple sleep modes with autonomous sleep and wake-up sequence control are supported. Thermal Management Subsystem APPLICATIONS The thermal management and protection subsystem allows the host processor to manage the power dissipation of the PMU and the overall system dynamically. The PMU provides a thermal warning to the host processor when the temperature reaches a certain threshold such that the system can turn off some of the non-essential functions, reduce the clock frequency and etc to manage the system temperature. Tablet PC Mobile Internet Devices (MID) Ebooks Personal Navigation Devices The ACT8847 is available in a compact, Pb-Free and RoHS-compliant TQFN66-48 package. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -1- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 FUNCTIONAL BLOCK DIAGRAM VP1 To Battery REG1 SW1 OUT1 OUT1 GP14 ACT8847 VP2 VIO REG2 SW2 nRSTO To Battery OUT2 OUT2 INL2 GP2 nPBIN VP3 PUSH BUTTON To Battery VIO SW3 REG3 nPBSTAT OUT3 OUT3 VIO GP3 nIRQ VP4 REG4 SW4 PWRHLD OUT4 OUT4 PWREN GP14 To Battery VSELR2 System Control INL1 REG5 LDO OUT5 REG6 LDO OUT6 REG7 LDO OUT7 SCL SDA REFBP To Battery OUT5 OUT6 OUT7 Reference INL2 GPIO1 REG8 LDO OUT8 REG9 LDO OUT9 To Battery OUT8 GPIO2 GPIO3 GPIO4 OUT9 INL3 GPIO5 To Battery GPIO6 REG10 LDO OUT10 REG11 LDO OUT11 REG12 LDO OUT12 REG13 OUT13 RTC LDO GA Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. OUT10 OUT11 OUT12 OUT13 EP -2- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 ORDERING INFORMATION PART NUMBER VOUT1 VOUT2 VOUT3 VOUT4 VOUT5 VOUT6 VOUT7 VOUT8 VOUT9 VOUT10 VOUT11 VOUT12 VOUT13 ACT8847QM102-T 1.35V 3.3V 3.8V 1.3V 3.3V OFF 3.3V OFF OFF OFF OFF OFF 3.3V ACT8847QM103-T 1.35V 3.3V 3.8V 1.3V 3.3V OFF 3.3V 3.3V 3.1V OFF OFF OFF 3.3V ACT8847QM171-T 1.2V 1.2V 1.1V 1.1V 1.1V 1.1V 3.3V 1.8V 3.3V 1.2V 1.1V 1.8V 1.8V ACT8847QM174-T 1.5V 1.2V 1.1V 1.1V 1.1V 1.1V 3.3V 1.8V 3.3V 1.5V 1.1V 1.8V 1.8V ACT8847QM211-T 1.3V 1.1V 1.5V OFF OFF OFF 3.3V 1.8V 2.5V OFF 2.8V OFF 3.3V ACT8847QM600-T 1.0V 1.3V 1.0V 1.125V 1.8V 3.0V 1.8V 3.3V 3.3V 1.1V 1.8V 1.0V 1.8V ACT8849QM614-T 2.8V 1.2V 2.0V 2.8V 1.8V 1.8V 2.8V 1.8V 1.8V 1.0V 1.2V 1.0V 1.8V ACT8847QM502-T 1.4V 1.4V 1.5V 3.3V OFF OFF 2.8V 1.8V 3.0V 2.5V OFF OFF 3.2V ACT8847QM503-T OFF 1.4V 3.3/3.1V 1.5/1.35V 2.5V OFF 3.3V 1.8V OFF OFF 1.2V 0.75V 3.3V PACKAGE PINS TEMPERATURE RANGE TQFN66-48 48 -40C to +85C ACT8847QM_ _ _-T Active-Semi Product Number Package Code Pin Count CMI Option Tape and Reel : All Active-Semi components are RoHS Compliant and with Pb-free plating unless specified differently. The term Pb-free means semiconductor products that are in compliance with current RoHS (Restriction of Hazardous Substances) standards. : The Package Code designator "Q" represents QFN. : The Pin Count designator "M" represents 48 pins. : "xxx" represents the CMI (Code Matrix Index) option. The CMI identifies the IC's default register settings. : ACT8847QM174-T is dedicated to S5PV310 application. : ACT8847 Data Sheet is described according to ACT8847QM171-T application; please see the Appendix of ACT8847QM211-T for its specification. : ACT8847QM600-T and ACT8849QM614-T is the association application for Samsung Exynos 4412/ 4212 platforms; please see the Appendix of APP_ACT8847 ACT8849_Rev0_16JUN14_P for its specification. : ACT8847QM502-T is dedicated to Freescale i.MX6 application. : ACT8847QM102-T is dedicated to Freescale i.MX6UL/i.MX6ULL with custom startup and system level considerations Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -3- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 PIN CONFIGURATION OUT13 GPIO4 OUT7 OUT6 INL1 OUT5 GPIO3 GPIO2 GPIO1 OUT3 VP3 VP3 TOP VIEW SW3 GPIO5 SW3 GPIO6 GP3 nIRQ OUT10 nRSTO OUT11 PWRHLD INL3 nPBIN OUT12 VP1 VSELR2 OUT1 ACT8847 nPBSTAT GP2 SW1 GP14 EP SW2 SW4 SW2 SCL SDA OUT8 OUT4 GA OUT9 INL2 REFBP PWREN OUT2 VP2 VP2 VP4 Thin - QFN (TQFN66-48) Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -4- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 PIN DESCRIPTIONS PIN NAME 1, 2 SW3 Switch Node for REG3. 3 GP3 Power Ground for REG3. Connect GP14, GP2, GP3, and GA together at a single point as close to the IC as possible. 4 OUT10 REG10 output. Bypass it to ground with a 2.2F capacitor. 5 OUT11 REG11 output. Bypass it to ground with a 2.2F capacitor. 6 INL3 7 OUT12 8 VSELR2 9 nPBSTAT 10 GP2 Power ground for REG2. Connect GP14, GP2, GP3, and GA together at a single point as close to the IC as possible. 11, 12 SW2 Switch Node for REG2. 13, 14 VP2 Power input for REG2. Bypass to GP2 with a high quality ceramic capacitor placed as close to the IC as possible. 15 OUT2 16 PWREN Power enable input. 17 REFBP Reference Bypass. Connect a 0.047F ceramic capacitor from REFBP to GA. This pin is discharged to GA in shutdown. 18 INL2 Power Input for REG8, REG9. INL2 must be connected to input power, even if REG8 and REG9 are not used. 19 OUT9 REG9 output. Bypass it to ground with a 2.2F capacitor. 20 GA 21 OUT4 Output voltage sense for REG4. 22 OUT8 REG8 output. Bypass it to ground with a 2.2F capacitor. 23 SDA Data Input for I2C Serial Interface. Data is read on the rising edge of SCL. 24 SCL Clock Input for I2C Serial Interface. 25 VP4 Power input for REG4. Bypass to GP14 with a high quality ceramic capacitor placed as close to the IC as possible. Innovative PowerTM DESCRIPTION Power input for REG10, REG11 and REG12. REG12 output. Bypass it to ground with a 2.2F capacitor. Output Voltage Selection for REG2. Drive to logic low to select default output voltage. Drive to logic high to select secondary output voltage. Active-Low Open-Drain Push-Button Status Output. nPBSTAT is asserted low whenever the nPBIN is pushed, and is high-Z otherwise. Output Voltage Sense for REG2. Analog Ground. ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -5- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 PIN DESCRIPTIONS CONT'D PIN NAME 26 SW4 Switch Node for REG4. 27 GP14 Power Ground for REG1 and REG4. Connect GP14, GP2, GP3, and GA together at a single point as close to the IC as possible. 28 SW1 Switch Node for REG1. 29 OUT1 Output Voltage Sense for REG1. 30 VP1 31 nPBIN 32 PWRHLD 33 nRSTO 34 nIRQ 35 GPIO6 General Purpose I/O #6. Configured as PWM LED driver output for up to 6mA current with programmable frequency and duty cycle. See the PWM LED Drive section for more information. 36 GPIO5 General Purpose I/O #5. Configured as PWM LED driver output for up to 6mA current with programmable frequency and duty cycle. See the PWM LED Driver section for more information. 37 OUT13 REG13 output. Bypass it to ground with a 2.2F capacitor. 38 OUT7 REG7 output. Bypass it to ground with a 2.2F capacitor. 39 GPIO4 General Purpose I/O #4. Configured as PWM LED driver output for up to 6mA current with programmable frequency and duty cycle. See the PWM LED Driver section for more information. 40 OUT6 REG6 output. Bypass it to ground with a 2.2F capacitor. 41 INL1 Power Input for REG5, REG6, REG7. 42 OUT5 REG5 output. Bypass it to ground with a 2.2F capacitor. 43 GPIO3 General Purpose I/O #3. Configured as PWM LED driver output for up to 6mA current with programmable frequency and duty cycle. See the PWM LED Drier section for more information. 44 GPIO2 General Purpose I/O #2. Configured as VSELR4 for Voltage Selection of REG4. Drive to logic low to select default output voltage. Drive to logic high to select secondary output voltage. 45 GPIO1 General Purpose I/O #1. Configured as VSELR3 for Voltage Selection of REG3. Drive to logic low to select default output voltage. Drive to logic high to select secondary output voltage. 46 OUT3 Output Voltage Sense for REG3. 47,48 VP3 Power input for REG3. Bypass to GP3 with a high quality ceramic capacitor placed as close to the IC as possible. EP EP Exposed Pad. Must be soldered to ground on PCB. Innovative PowerTM DESCRIPTION Power Input for REG1. Bypass to GP14 with a high quality ceramic capacitor placed as close to the IC as possible. Master Enable Input. Drive nPBIN to GA through a 50k resistor to enable the IC, drive nPBIN directly to GA to assert a Manual-Reset condition. Power hold Input. PWRHLD is internally pulled down to GA through a 900k resistor. Open-Drain Reset Output. Open-Drain Interrupt Output. ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -6- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 ABSOLUTE MAXIMUM RATINGS PARAMETER VALUE UNIT INL1, INL2, INL3 to GA; VP1, SW1, OUT1 to GP14; VP2, SW2, OUT2 to GP2; VP3, SW3, OUT3 to GP3; VP4, SW4, OUT4 to GP14 -0.3 to 6 V -0.3 to + 0.3 V OUT5, OUT6, OUT7, OUT13 to GA -0.3 to INL1 + 0.3 V OUT8, OUT9, GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, VSELR2, nPBIN, nRSTO, nIRQ, nPBSTAT, PWREN, PWRHLD, REFBP, SCL, SDA to GA -0.3 to INL2 + 0.3 V OUT10, OUT11, OUT12 to GA -0.3 to INL3 + 0.3 V Junction to Ambient Thermal Resistance 21 C/W Operating Ambient Temperature Range -40 to 85 C Operating Junction Temperature -40 to 125 C Storage Temperature -55 to 150 C 300 C GP14, GP2, GP3 to GA Lead Temperature (Soldering, 10 sec) : Do not exceed these limits to prevent damage to the device. Exposure to absolute maximum rating conditions for long periods may affect device reliability. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -7- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 I2C INTERFACE ELECTRICAL CHARACTERISTICS (VINL2 = 3.6V, TA = 25C, unless otherwise specified.) PARAMETER TEST CONDITIONS MIN SCL, SDA Input Low VINL2 = 3.1V to 5.5V, TA = -40C to 85C SCL, SDA Input High VINL2 = 3.1V to 5.5V, TA = -40C to 85C TYP MAX UNIT 0.35 V 1.55 V SDA Leakage Current 1 A SCL Leakage Current 1 A 0.35 V SDA Output Low IOL = 5mA SCL Clock Period, tSCL 1.5 s SDA Data Setup Time, tSU 100 ns SDA Data Hold Time, tHD 300 ns Start Setup Time, tST For Start Condition 100 ns Stop Setup Time, tSP For Stop Condition 100 ns Figure 1: I2C Compatible Serial Bus Timing tSCL SCL tST tHD tSU tSP SDA Start condition Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Stop condition -8- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 GLOBAL REGISTER MAP BITS BLOCK ADDRESS SYS 0x00 SYS 0x01 REG1 REG1 REG2 0x10 0x12 0x20 REG2 0x21 REG2 0x22 REG3 REG3 REG3 0x30 0x31 0x32 REG4 0x40 REG4 0x41 REG4 0x42 REG5 0x50 REG5 REG6 REG6 0x51 0x58 0x59 REG7 0x60 REG7 0x61 REG8 0x68 REG8 0x69 D7 NAME D6 nBATLEVMSK nBATSTAT D5 D4 D3 D2 D1 D0 VBATDAT Reserved BATLEV[3] BATLEV[2] BATLEV[1] BATLEV[0] DEFAULT 0 R R 0 0 0 0 0 Reserved NAME nTMSK TSTAT Reserved Reserved Reserved Reserved Reserved DEFAULT 0 R 0 0 0 0 0 0 NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 0 0 1 1 0 0 0 NAME ON Reserved Reserved Reserved Reserved PHASE nFLTMSK OK DEFAULT 1 1 0 0 0 0 0 R NAME Reserved Reserved VSET0[5] VSET0[4] VSET0[3] VSET0[2] VSET0[1] VSET0[0] DEFAULT 0 0 0 1 1 0 0 0 NAME Reserved Reserved VSET1[5] VSET1[4] VSET1[3] VSET1[2] VSET1[1] VSET1[0] DEFAULT 0 0 0 1 1 0 0 0 OK NAME ON Reserved Reserved Reserved Reserved PHASE nFLTMSK DEFAULT 1 1 0 1 0 0 0 R NAME Reserved Reserved VSET0[5] VSET0[4] VSET0[3] VSET0[2] VSET0[1] VSET0[0] DEFAULT 0 0 0 1 0 1 0 0 NAME Reserved Reserved VSET1[5] VSET1[4] VSET1[3] VSET1[2] VSET1[1] VSET1[0] DEFAULT 0 0 0 1 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved PHASE nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R NAME Reserved Reserved VSET0[5] VSET0[4] VSET0[3] VSET0[2] VSET0[1] VSET0[0] DEFAULT 0 0 0 1 0 1 0 0 VSET1[0] NAME Reserved Reserved VSET1[5] VSET1[4] VSET1[3] VSET1[2] VSET1[1] DEFAULT 0 0 0 1 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved PHASE nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R VSET[0] NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] DEFAULT 0 0 0 1 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 0 0 1 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 0 0 1 0 R NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 1 1 1 1 0 0 1 OK NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK DEFAULT 1 1 0 0 0 1 0 R NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 0 1 0 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R : Default values of ACT8847QM171-T. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. -9- www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 GLOBAL REGISTER MAP CONT'D BITS BLOCK ADDRESS REG9 REG9 REG10 REG10 REG11 REG11 REG12 REG12 REG13 PB PB PB PB PB 0x70 0x71 0x80 0x81 0x90 0x91 0xA0 0xA1 0xB1 0xC0 0xC1 0xC2 0xC3 0xC5 GPIO6 0xE3 GPIO5 0xE4 GPIO3 GPIO4 0xF4 0xF5 NAME D7 D6 D5 D4 D3 D2 D1 D0 Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 0 1 1 1 0 0 1 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 0 0 1 1 0 0 0 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 0 0 1 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 1 0 1 0 R NAME Reserved Reserved VSET[5] VSET[4] VSET[3] VSET[2] VSET[1] VSET[0] DEFAULT 0 1 1 0 0 1 0 0 NAME ON Reserved Reserved Reserved Reserved DIS nFLTMSK OK DEFAULT 1 1 0 0 0 1 0 R NAME ON Reserved Reserved Reserved Reserved Reserved Reserved Reserved DEFAULT 1 0 0 0 0 0 0 0 NAME PBAMSK PBDMSK Reserved Reserved Reserved Reserved WDSREN WDPCEN 0 0 DEFAULT 0 0 0 0 0 NAME INTADR [7] INTADR [6] INTADR [5] INTADR [4] INTADR [3] INTADR [2] INTADR [1] 0 INTADR [0] DEFAULT R R R R R R R R NAME PBASTAT PBDSTAT PBDAT Reserved Reserved Reserved Reserved Reserved DEFAULT R R R R R R R R NAME Reserved Reserved Reserved Reserved Reserved Reserved Reserved SIPC DEFAULT 0 0 0 0 0 0 0 0 NAME Reserved Reserved Reserved Reserved Reserved Reserved PCSTAT SRSTAT DEFAULT 0 0 0 0 0 0 R R NAME PWM6EN FRE6[2] FRE6[1] FRE6[0] DUTY6[3] DUTY6[2] DUTY6[1] DUTY6[0] DEFAULT 0 0 0 0 0 0 0 0 DUTY5[0] NAME PWM5EN FRE5[2] FRE5[1] FRE5[0] DUTY5[3] DUTY5[2] DUTY5[1] DEFAULT 0 0 0 0 0 0 0 0 NAME PWM3EN FRE3[2] FRE3[1] FRE3[0] DUTY3[3] DUTY3[2] DUTY3[1] DUTY3[0] DEFAULT 0 0 0 0 0 0 0 0 NAME PWM4EN FRE4[2] FRE4[1] FRE4[0] DUTY4[3] DUTY4[2] DUTY4[1] DUTY4[0] DEFAULT 0 0 0 0 0 0 0 0 : Default values of ACT8847QM171-T. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 10 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 REGISTER AND BIT DESCRIPTIONS BLOCK ADDRESS BIT NAME ACCESS DESCRIPTION Battery Voltage Level Interrupt Mask. Set this bit to 1 to unmask the interrupt. See the Programmable Battery Voltage Monitor section for more information SYS 0x00 [7] nBATLEVMSK R/W SYS 0x00 [6] nBATSTAT R Battery Voltage Status. Value is 1 when BATLEV interrupt is generated, value is 0 otherwise. SYS 0x00 [5] VBATDAT R Battery Voltage Monitor real time status. Value is 1 when VBAT < BATLEV, value is 0 otherwise. SYS 0x00 [4] - R/W Reserved. SYS 0x00 [3:0] BATLEV R/W Battery Voltage Detect Threshold. Defines the BATLEV voltage threshold. See the Programmable Battary Voltage Monitor section for more information. SYS 0x01 [7] nTMSK R/W Thermal Interrupt Mask. Set this bit to 1 to unmask the interrupt. SYS 0x01 [6] TSTAT R Thermal Interrupt Status. Value is 1 when a thermal interrupt is generated, value is 0 otherwise. SYS 0x01 [5:0] - R/W Reserved. REG1 0x10 [7:6] - R Reserved. REG1 0x10 [5:0] VSET0 R/W Primary Output Voltage Selection. See the Output Voltage Programming section for more information REG1 0x12 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG1 0x12 [6:3] - R REG1 0x12 [2] PHASE R/W Regulator Phase Control. Set bit to 1 for the regulator to operate 180 out of phase with the oscillator, clear bit to 0 for the regulator to operate in phase with the oscillator. REG1 0x12 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG1 0x12 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG2 0x20 [7:6] - R Reserved. REG2 0x20 [5:0] VSET0 R/W REG2 0x21 [7:6] - R REG2 0x21 [5:0] VSET1 R/W Secondary Output Voltage Selection. Valid when VSEL is driven high. See the Output Voltage Programming section for more information. REG2 0x22 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG2 0x22 [6:3] - R REG2 0x22 [2] PHASE R/W Regulator Phase Control. Set bit to 1 for the regulator to operate 180 out of phase with the oscillator, clear bit to 0 for the regulator to operate in phase with the oscillator. REG2 0x22 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG2 0x22 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG3 0x30 [7:6] - R Reserved. REG3 0x30 [5:0] VSET0 R/W Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Reserved. Primary Output Voltage Selection. Valid when VSEL is driven low. See the Output Voltage Programming section for more information Reserved. Reserved. Primary Output Voltage Selection. Valid when VSEL is driven low. See the Output Voltage Programming section for more information - 11 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 REGISTER AND BIT DESCRIPTIONS CONT'D BLOCK ADDRESS BIT NAME ACCESS DESCRIPTION REG3 0x31 [7:6] - R REG3 0x31 [5:0] VSET1 R/W Secondary Output Voltage Selection. Valid when VSEL is driven high. See the Output Voltage Programming section for more information. REG3 0x32 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG3 0x32 [6:3] - R REG3 0x32 [2] PHASE R/W Regulator Phase Control. Set bit to 1 for the regulator to operate 180 out of phase with the oscillator, clear bit to 0 for the regulator to operate in phase with the oscillator. REG3 0x32 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG3 0x32 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG4 0x40 [7:6] - R Reserved. REG4 0x40 [5:0] VSET0 R/W REG4 0x41 [7:6] - R REG4 0x41 [5:0] VSET1 R/W Secondary Output Voltage Selection. Valid when VSEL is driven high. See the Output Voltage Programming section for more information. REG4 0x42 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG4 0x42 [6:3] - R REG4 0x42 [2] PHASE R/W Regulator Phase Control. Set bit to 1 for the regulator to operate 180 out of phase with the oscillator, clear bit to 0 for the regulator to operate in phase with the oscillator. REG4 0x42 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG4 0x42 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG5 0x50 [7:6] - R Reserved. REG5 0x50 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG5 0x51 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG5 0x51 [6:3] - R Reserved. Reserved. Primary Output Voltage Selection. Valid when VSEL is driven low. See the Output Voltage Programming section for more information Reserved. Reserved. Reserved. REG5 0x51 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG5 0x51 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG5 0x51 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG6 0x58 [7:6] - R Reserved. REG6 0x58 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG6 0x59 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 12 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 REGISTER AND BIT DESCRIPTIONS CONT'D BLOCK ADDRESS BIT REG6 0x59 [6:3] NAME ACCESS - R DESCRIPTION Reserved. REG6 0x59 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG6 0x59 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable faultinterrupts, clear bit to 0 to disable fault-interrupts. REG6 0x59 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG7 0x60 [7:6] - R Reserved. REG7 0x60 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG7 0x61 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG7 0x61 [6:3] - R Reserved. REG7 0x61 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG7 0x61 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable faultinterrupts, clear bit to 0 to disable fault-interrupts. REG7 0x61 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG8 0x68 [7:6] - R Reserved. REG8 0x68 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG8 0x69 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG8 0x69 [6:3] - R Reserved. REG8 0x69 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG8 0x69 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable faultinterrupts, clear bit to 0 to disable fault-interrupts. REG8 0x69 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG9 0x70 [7:6] - R Reserved. REG9 0x70 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG9 0x71 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG9 0x71 [6:3] - R REG9 0x71 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG9 0x71 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable faultinterrupts, clear bit to 0 to disable fault-interrupts. REG9 0x71 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG10 0x80 [7:6] - R Reserved. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Reserved. - 13 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 REGISTER AND BIT DESCRIPTIONS CONT'D BLOCK ADDRESS BIT NAME ACCESS DESCRIPTION REG10 0x80 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG10 0x81 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG10 0x81 [6:3] - R REG10 0x81 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG10 0x81 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG10 0x81 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG11 0x90 [7:6] - R Reserved. REG11 0x90 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG11 0x91 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG11 0x91 [6:3] - R Reserved. Reserved. REG11 0x91 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG11 0x91 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG11 0x91 [0] OK R Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. REG12 0xA0 [7:6] - R Reserved. REG12 0xA0 [5:0] VSET R/W Output Voltage Selection. See the Output Voltage Programming section for more information. REG12 0xA1 [7] ON R/W Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. REG12 0xA1 [6:3] - R REG12 0xA1 [2] DIS R/W Output Discharge Control. When activated, LDO output is discharged to GA through 1.5k resistor when in shutdown. Set bit to 1 to enable output voltage discharge in shutdown, clear bit to 0 to disable this function. REG12 0xA1 [1] nFLTMSK R/W Regulator Fault Mask Control. Set bit to 1 enable fault-interrupts, clear bit to 0 to disable fault-interrupts. REG12 0xA1 [0] OK R REG13 0xB1 [7] ON R/W REG13 0xB1 [6:0] - R PB 0xC0 7 nPBAMSK R/W nPBIN Assertion Interrupt Control. Set this bit to 1 to generate an interrupt when nPBIN is asserted. PB 0xC0 6 nPBDMSK R/W nPBIN De-assertion Interrupt Control. Set this bit to 1 to generate an interrupt when nPBIN is de-asserted. PB 0xC0 [5:2] - R PB 0xC0 Innovative PowerTM 1 WDSREN ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. R/W Reserved. Regulator Power-OK Status. Value is 1 when output voltage exceeds the power-OK threshold, value is 0 otherwise. Regulator Enable Bit. Set bit to 1 to enable the regulator, clear bit to 0 to disable the regulator. Reserved. Reserved. Watchdog Soft-Reset Enable. Set this bit to 1 to enable watchdog function. When the watchdog timer expires, the PMU commences a soft-reset routine. This bit is automatically reset to 0 when entering sleep mode. - 14 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 REGISTER AND BIT DESCRIPTIONS CONT'D BLOCK ADDRESS BIT PB PB 0xC0 0xC0 [5:2] 1 NAME ACCESS - R WDSREN DESCRIPTION Reserved. R/W Watchdog Soft-Reset Enable. Set this bit to 1 to enable watchdog function. When the watchdog timer expires, the PMU commences a soft-reset routine. This bit is automatically reset to 0 when entering sleep mode. Watchdog Power-Cycle Enable. Set this bit to 1 to enable watchdog function. When watchdog timer expires, the PMU commence a power cycle. This bit is automatically reset to 0 when entering sleep mode. PB 0xC0 0 WDPCEN R/W PB 0xC1 [7:0] INTADR R Interrupt Address. It holds the address of the block that triggers the interrupt. This byte defaults to 0xFF and is automatically set to 0xFF after being read. Bit 7 is the MSB while Bit 0 is the LSB. PB 0xC2 7 PBASTAT R nPBIN Assertion Interrupt Status. The value of this bit is 1 if the nPBIN Assertion Interrupt is triggered. PB 0xC2 6 PBDSTAT R nPBIN De-assertion Interrupt Status. The value of this bit is 1 if the nPBIN De-assertion Interrupt is triggered. PB 0xC2 5 PBASTAT R nPBIN Status bit. This bit contains the real-time status of the nPBIN pin. The value of this bit is 1 if nPBIN is asserted, and is 0 if nPBIN is de-asserted. PB 0xC2 [4:0] - R Reserved. PB 0xC3 [7:1] - R Reserved. PB 0xC3 0 SIPC R/W PB 0xC5 [7:2] - R PB 0xC5 1 PCSTAT R/W Power-cycle Flag. The value of this bit is 1 after a power cycle. This bit is automatically cleared to 0 after read. PB 0xC5 0 SRSTAT R/W Soft-reset Flag. The value of this bit is 1 after a soft-reset. This bit is automatically cleared to 0 after read. GPIO6 0xE3 [7] PWM6EN R/W PWM Function Enable. Set 1 to enable PWM function of GPIO6. GPIO6 0xE3 [6:4] FRE6 R/W GPIO6 0xE3 [3:0] DUTY6 R/W GPIO5 0xE4 [7] PWM5EN R/W GPIO5 0xE4 [6:4] FRE5 R/W GPIO5 0xE4 [3:0] DUTY5 R/W GPIO3 0xF4 [7] PWM3EN R/W GPIO3 0xF4 [6:4] FRE3 R/W GPIO3 0xF4 [3:0] DUTY3 R/W GPIO4 0xF5 [7] PWM4EN R/W GPIO4 0xF5 [6:4] FRE4 R/W GPIO4 0xF5 [3:0] DUTY4 R/W Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. Software Initiated Power Cycle. When this bit is set, the PMU commences a power cycle after 8ms delay. Reserved. PWM Frequency Selection Bits for GPIO6. See the Table 6 for code to frequency cross. Duty Cycle Selection Bits for GPIO6. See the Table 7 for code to duty cross. PWM Function Enable. Set 1 to enable PWM function of GPIO5. PWM Frequency Selection Bits for GPIO5. See the Table 6 for code to frequency cross. Duty Cycle Selection Bits for GPIO5. See the Table 7 for code to duty cross. PWM Function Enable. Set 1 to enable PWM function of GPIO3. PWM Frequency Selection Bits for GPIO3. See the Table 6 for code to frequency cross. Duty Cycle Selection Bits for GPIO3. See the Table 7 for code to duty cross. PWM Function Enable. Set 1 to enable PWM function of GPIO4. PWM Frequency Selection Bits for GPIO4. See the Table 6 for code to frequency cross. Duty Cycle Selection Bits for GPIO4. See the Table 7 for code to duty cross. - 15 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 SYSTEM CONTROL ELECTRICAL CHARACTERISTICS (VINL2 = 3.6V, TA = 25C, unless otherwise specified.) PARAMETER TEST CONDITIONS Input Voltage Range MIN TYP 3.0 2.6 UNIT 5.5 V 3.0 V UVLO Threshold Voltage VINL2 Rising UVLO Hysteresis VINL2 Hysteresis 200 Operating Supply Current All Regulators Enabled but no load 0.6 1.2 mA Shutdown Supply Current All Regulators Disabled except REG13 10 20 A 2.25 2.5 MHz Oscillator Frequency 2.0 Logic High Input Voltage 1.4 2.8 MAX mV V Logic Low Input Voltage 0.4 V Leakage Current V[nIRQ] = V[nRSTO] = 4.2V 1 A Low Level Output Voltage nIRQ, nRSTO, ISINK = 5mA 0.3 V Thermal Shutdown Temperature Temperature rising Thermal Shutdown Hysteresis Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 16 - 160 C 20 C www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 STEP-DOWN DC/DC ELECTRICAL CHARACTERISTICS (VVP1 = VVP2 = VVP3 = VVP4 = 3.6V, TA = 25C, unless otherwise specified.) PARAMETER CONDITIONS Operating Voltage Range MIN TYP 2.7 UVLO Threshold Input Voltage Rising UVLO Hysteresis Input Voltage Falling 100 Standby Supply Current VOUT = 103%, Regulator Enabled 72 Shutdown Current VVP = 5.5V, Regulator Disabled 0 Output Voltage Accuracy 2.5 VOUT 1.0V, IOUT = 10mA -1% VOUT < 1.0V, IOUT = 10mA -10 2.6 VNOM MAX UNIT 5.5 V 2.7 V mV 100 A 2 A 1% V 10 mV Line Regulation VVP = Max (VNOM +1V, 3.2V) to 5.5V 0.15 %/V Load Regulation REG1/4 IOUT = 10mA to IMAX 1.70 %/A Load Regulation REG2/3 IOUT = 10mA to IMAX 1.00 %/A Power Good Threshold VOUT Rising 93 %VNOM Power Good Hysteresis VOUT Falling 2 %VNOM Switching Frequency VOUT 20% of VNOM 2 VOUT = 0V 2.25 2.5 MHz 550 kHz Soft-Start Period 400 s Minimum On-Time 75 ns REG1 AND REG4 Maximum Output Current 1.5 Current Limit 1.8 A 2.2 2.7 A PMOS On-Resistance ISW = -100mA 0.11 NMOS On-Resistance ISW = 100mA 0.08 SW Leakage Current VVP = 5.5V, VSW = 0 or 5.5V 0 2 A Input Capacitor 4.7 F Output Capacitor 33 F Power Inductor 1.0 2.2 3.3 H REG2 AND REG3 Maximum Output Current 2.8 Current Limit 3.5 A 4.2 A PMOS On-Resistance ISW = -100mA 0.07 NMOS On-Resistance ISW = 100mA 0.08 SW Leakage Current VVP = 5.5V, VSW = 0 or 5.5V 0 2 A Input Capacitor 10 F Output Capacitor 44 F Power Inductor 0.5 1 2.2 H : VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. : IMAX Maximum Output Current. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 17 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 LOW-NOISE LDO ELECTRICAL CHARACTERISTICS (VINL1 = VINL2 = 3.6V, COUT5 = COUT6 = COUT7 = COUT8 = COUT9 = 2.2F, TA = 25C, unless otherwise specified.) PARAMETER TEST CONDITIONS Operating Voltage Range Output Voltage Accuracy MIN TYP 2.5 VOUT 1.0V, IOUT = 10mA -1 VOUT < 1.0V, IOUT = 10mA -10 VNOM MAX UNIT 5.5 V 1 % 10 mV Line Regulation VINL = Max (VOUT + 0.5V, 3.6V) to 5.5V 0.5 mV Load Regulation IOUT = 1mA to IMAX 0.1 V/A f = 1kHz, IOUT = 20mA, VOUT = 1.2V 75 f = 10kHz, IOUT = 20mA, VOUT = 1.2V 65 Regulator Enabled 25 Regulator Disabled 0 Power Supply Rejection Ratio Supply Current per Output dB 2 A Soft-Start Period VOUT = 3.0V 140 s Power Good Threshold VOUT Rising 92 % Power Good Hysteresis VOUT Falling 3.5 % Output Noise IOUT = 20mA, f = 10Hz to 100kHz, VOUT = 1.2V 30 VRMS Discharge Resistance LDO Disabled, DIS[ ] = 1 1.5 k LDO rated at 150mA (REG5 & REG6) Dropout Voltage IOUT = 80mA, VOUT > 3.1V Maximum Output Current Current Limit 140 280 150 VOUT = 95% of regulation voltage mA 180 Recommend Output Capacitor mV mA 2.2 F LDO rated at 350mA (REG7, REG8 & REG9) Dropout Voltage IOUT = 160mA, VOUT > 3.1V Maximum Output Current Current Limit VOUT = 95% of regulation voltage 140 280 mV 350 mA 400 mA Recommend Output Capacitor 2.2 F : VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. : IMAX Maximum Output Current. : Dropout Voltage is defined as the differential voltage between input and output when the output voltage drops 100mV below the regulation voltage (for 3.1V output voltage or higher). : LDO current limit is defined as the output current at which the output voltage drops to 95% of the respective regulation voltage. Under heavy overload conditions the output current limit folds back by 50% (typ.) Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 18 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 LOW-INPUT VOLTAGE LDO ELECTRICAL CHARACTERISTICS (VINL3 = 3.6V, COUT10 = COUT11 = COUT12 = 2.2F, TA = 25C, unless otherwise specified.) PARAMETER TEST CONDITIONS Operating Voltage Range Output Voltage Accuracy MIN TYP 1.7 VOUT 1.0V, IOUT = 10mA -1 VOUT < 1.0V, IOUT = 10mA -10 VNOM MAX UNIT 5.5 V 1 % 10 mV Line Regulation VINL = Max (VOUT + 0.5V, 3.6V) to 5.5V 0.5 mV Load Regulation IOUT = 1mA to IMAX 0.1 V/A f = 1kHz, IOUT = 20mA, VOUT = 1.2V 50 f = 10kHz, IOUT = 20mA, VOUT = 1.2V 40 Regulator Enabled 22 Regulator Disabled 0 Power Supply Rejection Ratio Supply Current per Output dB 2 A Soft-Start Period VOUT = 3.0V 100 s Power Good Threshold VOUT Rising 92 % Power Good Hysteresis VOUT Falling 3.5 % Output Noise IOUT = 20mA, f = 10Hz to 100kHz, VOUT = 1.2V 30 VRMS Discharge Resistance LDO Disabled, DIS[ ] = 1 1.5 k IOUT = 80mA, VOUT > 3.1V 100 LDO rated at 150mA (REG10) Dropout Voltage Maximum Output Current Current Limit VOUT = 95% of regulation voltage 200 mV 150 mA 180 mA Recommend Output Capacitor 2.2 F LDO rated at 350mA (REG11 & REG12) Dropout Voltage IOUT = 160mA, VOUT > 3.1V Maximum Output Current Current Limit 100 350 VOUT = 95% of regulation voltage mV mA 400 Recommend Output Capacitor 200 mA 2.2 F : VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. : IMAX Maximum Output Current. : Dropout Voltage is defined as the differential voltage between input and output when the output voltage drops 100mV below the regulation voltage (for 3.1V output voltage or higher). : LDO current limit is defined as the output current at which the output voltage drops to 95% of the respective regulation voltage. Under heavy overload conditions the output current limit folds back by 50% (typ) Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 19 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 LOW-POWER(ALWAYS-ON) LDO ELECTRICAL CHARACTERISTICS (VINL1 = 3.6V, COUT13 = 1F, TA = 25C, unless otherwise specified.) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 5.5 V REG13 -- VNOM = 1.8V Operating Voltage Range 2.5 Output Voltage Accuracy -3 Line Regulation VINL1 = Max (VOUT + 0.2V, 2.5V) to 5.5V VNOM 3 13 Supply Current from VINL1 5 Maximum Output current Recommend Output Capacitor % mV A 50 mA 0.47 F PWM LED DRIVER ELECTRICAL CHARACTERISTICS (VINL2 = 3.6V, TA = 25C, unless otherwise specified.) PARAMETER TEST CONDITIONS Output Current 100% Duty Cycle Output Low Voltage Feed in with 6mA Leakage Current Sinking from 5.5V source PWM Frequency FRE[2:0] = 000 PWM Duty Adjustment DUTY[3:0] = 0000 to 1111 MIN TYP MAX UNIT 6 10 16 mA 0.35 V 1 A 0.25 6.26 Hz 100 % : VNOM refers to the nominal output voltage level for VOUT as defined by the Ordering Information section. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 20 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TYPICAL PERFORMANCE CHARACTERISTICS (TA = 25C, unless otherwise specified.) Frequency vs. Temperature VREF vs. Temperature 2.340 Frequency (MHz) VREF (V) 1.200 ACT8847-002 2.360 ACT8847-001 1.204 1.196 1.192 1.188 2.320 2.300 2.280 2.260 2.240 2.220 2.200 1.184 -40 -20 0 20 40 60 80 100 120 2.180 -40 140 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Startup of OUT6/4/2/3 Startup of OUT5/7/1/12 ACT8847-004 ACT8847-003 CH1 -20 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: VOUT5, 1V/div CH2: VOUT7, 2V/div CH3: VOUT1, 1V/div CH4: VOUT12, 2V/div TIME: 400s/div CH1: VOUT6, 1V/div CH2: VOUT4, 1V/div CH3: VOUT2, 1V/div CH4: VOUT3, 1V/div TIME: 400s/div Startup of OUT3/5/7/12 Startup of OUT11/10/8/9 ACT8847-006 ACT8847-005 CH1 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: VOUT3, 1V/div CH2: VOUT5, 1V/div CH3: VOUT7, 2V/div CH4: VOUT12, 1V/div TIME: 200s/div Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. CH1: VOUT11, 1V/div CH2: VOUT10, 1V/div CH3: VOUT8, 500mV/div CH4: VOUT9, 2V/div TIME: 400s/div - 21 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TYPICAL PERFORMANCE CHARACTERISTICS CONT'D (TA = 25C, unless otherwise specified.) Startup of nPBIN, OUT6/4/2 Startup of nPBIN, OUT6, nRSTO ACT8847-008 ACT8847-007 CH1 CH1 CH2 CH3 CH2 CH4 CH3 CH1: VnPBIN, 2V/div CH2: VOUT6, 1V/div CH3: VOUT4, 1V/div CH4: VOUT2, 1V/div TIME: 10ms/div CH1: VnPBIN, 2V/div CH2: VOUT6, 1V/div CH3: VnRSTO, 2V/div TIME: 20ms/div Sleep of PWREN, OUT3/5/11 Sleep of PWREN, OUT4/2/3 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: VPWREN, 2V/div CH2: VOUT3, 1V/div CH3: VOUT5, 1V/div CH3: VOUT11, 1V/div TIME: 1ms/div CH1: VPWREN, 2V/div CH2: VOUT4, 1V/div CH3: VOUT2, 1V/div CH3: VOUT3, 1V/div TIME: 1ms/div Sleep of PWREN, OUT10/8/9 nPBIN and nPBSTAT CH2 ACT8847-012 ACT8847-011 CH1 ACT8847-010 ACT8847-009 CH1 CH1 CH2 CH3 CH4 CH1: VnPBIN, 2V/div CH2: VnPBSTAT, 2V/div TIME: 10ms/div CH1: VPWREN, 2V/div CH2: VOUT10, 1V/div CH3: VOUT8, 1V/div CH3: VOUT9, 2V/div TIME: 1ms/div Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 22 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TYPICAL PERFORMANCE CHARACTERISTICS CONT'D (TA = 25C, unless otherwise specified.) Shutdown of PWRHOLD and nRSTO Shutdown of PWRHOLD and OUT11/10/8 ACT8847-014 ACT8847-013 CH1 CH1 CH2 CH2 CH3 CH4 CH1: VPWRHOLD, 2V/div CH2: VnRSTO, 2V/div TIME: 2ms/div CH1: VPWRHOLD, 2V/div CH2: VOUT11, 1V/div CH3: VOUT10, 1V/div CH3: VOUT8, 2V/div TIME: 400s/div Shutdown of PWRHOLD and OUT9/7/12 Shutdown of PWRHOLD and OUT3/5/6 ACT8847-016 ACT8847-015 CH1 CH1 CH2 CH2 CH3 CH3 CH4 CH4 CH1: VPWRHOLD, 2V/div CH2: VOUT9, 2V/div CH3: VOUT7, 2V/div CH3: VOUT12, 2V/div TIME: 400s/div CH1: VPWRHOLD, 2V/div CH2: VOUT3, 1V/div CH3: VOUT5, 1V/div CH3: VOUT6, 1V/div TIME: 2ms/div Shutdown of PWRHOLD and OUT1/4/2 REG1 Efficiency vs. Output Current CH2 VOUT = 1.2V VIN = 3.6V 80 Efficiency (%) CH1 CH3 CH4 ACT8847-018 ACT8847-017 100 VIN = 5.0V 60 VIN = 4.0V 40 20 0 CH1: VPWRHOLD, 2V/div CH2: VOUT1, 1V/div CH3: VOUT4, 1V/div CH3: VOUT2, 1V/div TIME: 1ms/div Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. 0 1 10 100 1000 10000 Output Current (mA) - 23 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TYPICAL PERFORMANCE CHARACTERISTICS CONT'D (TA = 25C, unless otherwise specified.) REG2 Efficiency vs. Output Current 80 Efficiency (%) VIN = 5.0V VIN = 4.0V 60 40 20 VIN = 5.0V 60 VIN = 4.0V 40 20 0 0 0 10 1 1000 100 10000 0 10000 REG10 @ 10mA vs. Temperature VIN = 3.6V ACT8847-022 ACT8847-021 VOUT = 1.1V 80 1.205 1.200 VIN = 5.0V 60 VOUT (V) Efficiency (%) 1000 100 Output Current (mA) REG4 Efficiency vs. Output Current VIN = 4.0V 40 1.195 1.190 20 1.185 0 1.180 0 10 1 1000 100 10000 -40 -20 0 Output Current (mA) 20 40 60 80 100 120 140 Temperature (C) VOUT10 @ 150mA vs. Temperature REG5/6 Dropout Voltage vs. IOUT 350 Dropout Voltage (mV) 1.182 ACT8847-024 400 ACT8847-023 1.186 VOUT (V) 10 1 Output Current (mA) 100 VIN = 3.6V VOUT = 1.1V 80 Efficiency (%) VIN = 3.6V ACT8847-020 VOUT = 1.2V ACT8847-019 100 REG3 Efficiency vs. Output Current 100 1.178 1.174 300 250 200 150 100 50 1.170 -40 0 -20 0 20 40 60 80 100 120 140 0 ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. 100 150 200 250 Output Current (mA) Temperature (C) Innovative PowerTM 50 - 24 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TYPICAL PERFORMANCE CHARACTERISTICS CONT'D (TA = 25C, unless otherwise specified.) REG5 VOUT vs. IOUT REG6 VOUT vs. IOUT Dropout Voltage (V) Dropout Voltage (V) 1.160 1.120 1.080 1.040 ACT8847-026 1.200 ACT8847-025 1.200 1.160 1.120 1.080 1.040 1.000 1.000 0 40 80 160 120 200 0 40 Output Current (mA) REG7/8/9 Dropout Voltage vs. IOUT 200 REG7 VOUT vs. IOUT Output Voltage (V) 300 200 100 ACT8847-028 3.400 ACT8847-027 Dropout Voltage (mV) 160 120 Output Current (mA) 400 3.360 3.320 3.280 3.240 0 3.200 50 0 100 150 200 250 300 350 400 0 50 Output Current (mA) 100 150 200 250 300 350 Output Current (mA) REG8 VOUT vs. IOUT REG9 VOUT vs. IOUT Output Voltage (V) 1.860 1.820 1.780 1.740 ACT8847-030 3.310 ACT8847-029 1.900 Output Voltage (V) 80 3.300 3.290 3.280 3.270 3.260 3.250 1.700 0 50 100 150 200 250 300 0 350 ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. 100 150 200 250 300 350 400 Output Current (mA) Output Current (mA) Innovative PowerTM 50 - 25 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TYPICAL PERFORMANCE CHARACTERISTICS CONT'D (TA = 25C, unless otherwise specified.) REG10 Dropout Voltage vs. IOUT REG10 VOUT vs. IOUT 1.300 Output Voltage (V) Dropout Voltage (mV) 200 150 100 1.260 1.220 1.180 1.140 50 1.000 0 50 0 100 150 200 0 40 160 120 Output Current (mA) REG11 Dropout Voltage vs. IOUT REG11 VOUT vs. IOUT Output Voltage (V) 1.200 150 100 1.160 1.120 1.080 50 1.040 0 1.000 100 200 300 200 ACT8847-034 ACT8847-033 200 0 0 400 50 100 150 200 250 300 350 300 350 Output Current (mA) Output Current (mA) REG12 VOUT vs. IOUT REG12 Dropout Voltage vs. IOUT 1.900 Output Voltage (V) 200 ACT8847-036 ACT8847-035 250 Dropout Voltage (mV) 80 Output Current (mA) 250 Dropout Voltage (mV) ACT8847-032 ACT8847-031 250 150 100 1.860 1.820 1.780 1.740 50 1.700 0 0 100 200 300 0 400 ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. 100 150 200 250 Output Current (mA) Output Current (mA) Innovative PowerTM 50 - 26 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 SYSTEM CONTROL INFORMATION Interfacing with the Samsung S5PC210/S5PV310 processors The ACT8847 is optimized for the Samsung S5PC210/S5PV310 and other application processors, supporting both the power domains as well as the signal interface. The following paragraphs describe how to design ACT8847 with the S5PC210/S5PV310 processors. cases where the description of interconnections between these devices benefits by doing so, both the ACT8847 pin names and the S5PC210/S5PV310 processors pin names are provided. When this is done, the S5PC210/S5PV310 pin names are located after the ACT8847 pin names, and are italicized and located inside parentheses. For example, PWREN (XPWRRGTON) refers to the logic signal applied to the ACT8847's PWREN input, identifying that it is driven from the S5PC210's XPWRRGTON output. While the ACT8847 supports many possible configurations for powering these processors, one of the most common configurations is detailed in this datasheet. In general, this document refers to the ACT8847 pin names and functions. However, in Table 1: ACT8847 and Samsung S5PC210 Power Domains ACT8847 REGPOWER DOMAIN ULATOR DEFAULT MAX POWER UP VOLTAGE CURRENT ORDER ON/OFF @ SLEEP TYPE REG1 VDD_MEM, VDD12_SLP_ON 1.2V 1.5A 7 ON DC/DC Step Down REG2 VDD_ARM 1.2V 2.8A 3 OFF DC/DC Step Down REG3 VDD_G3D 1.1V 2.8A 4 OFF DC/DC Step Down REG4 VDD_INT 1.1V 1.5A 2 OFF DC/DC Step Down REG5 VDD_PLL 1.1V 150mA 5 OFF Low-Noise LDO REG6 VDD_ALIVE 1.1V 150mA 1 ON Low-Noise LDO REG7 VDD33_SLP_ON 3.3V 350mA 6 ON Low-Noise LDO REG8 VDD18_SLP_OFF 1.8V 350mA 11 OFF Low-Noise LDO REG9 VDD33_SLP_OFF 3.3V 350mA 12 OFF Low-Noise LDO REG10 VDD12_SLP_OFF 1.2V 150mA 10 OFF Low Input-Voltage LDO REG11 VDD11_SLP_OFF 1.1V 350mA 9 OFF Low Input-Voltage LDO REG12 VDD18_SLP_ON 1.8V 350mA 8 ON Low Input-Voltage LDO REG13 VDD_RTC 1.8V 50mA 0 ON Always-ON LDO Table 2: ACT8847 and Samsung S5PC210 Power Mode Power Mode Control State Power Domain State Quiescent Current ALL ON PWRHLD is asserted, PWREN is asserted All Regulators ON 0.6mA SLEEP PWRHLD is asserted, PWREN is deasserted REG1/6/7/12/13 are ON, all other regulators are off. 200A SHUTDOWN ALL OFF Innovative PowerTM PWRHLD is de-asserted, PWREN is REG13 is ON, all other regulade-asserted, VINL2 > 2.6V tors are off. 10A PWRHLD is de-asserted, PWREN is de-asserted, VINL2 < 2.2V 5A ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 27 - All regulators off. www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Table 3: ACT8847 and S5PC210 Signal Interface ACT8847 DIRECTION SAMSUNG S5PC210 PWREN XPWRRGTON SCL Xi2cSCL[0] SDA Xi2cSDA[0] VSELR2 DVS_GPIO1 GPIO1/VSELR3 DVS_GPIO2 GPIO2/VSELR4 DVS_GPIO3 nRSTO XnRESET nIRQ XEINT0 nPBSTAT XEINT1 PWRHLD XPSHOLD : Typical connections shown, actual connections may vary. Control Signals Long Press / Power-cycle: Enable Inputs The ACT8847 features a variety of control inputs, which are used to enable and disable outputs depending upon the desired mode of operation. PWREN, PWRHLD are logic inputs, while nPBIN is a unique, multi-function input. nPBIN Multi-Function Input The ACT8847 features the nPBIN multi-function pin, which combines system enable/disable control with a hardware reset function. Select either of the two pin functions by asserting this pin, either through a direct connection to GA, or through a 50k resistor to GA, as shown in Figure 2. Manual Reset Function The second major function of the nPBIN input is to provide a manual-reset input for the processor. To manually-reset the processor, drive nPBIN directly to GA through a low impedance (less than 2.5k). An internal timer detects the duration of the MR event: If the MR is asserted for more than 4s, ACT8847 commences a power cycle routine in which case all regulators are turned off and then turned back on. A status bit, PCSTAT[ ], is set after the power cycle. The PCSTAT[ ] bit is automatically cleared to 0 after read. nPBSTAT Output nPBSTAT is an open-drain output that reflects the state of the nPBIN input; nPBSTAT is asserted low whenever nPBIN is asserted, and is high-Z otherwise. This output is typically used as an interrupt signal to the processor, to initiate a software-programmable routine such as operating mode selection or to open a menu. Connect nPBSTAT to an appropriate supply voltage through a 10k or greater resistor. Figure 2: nPBIN Input INL2 Short Press / Soft-Reset: 50k PushButton Detect If the MR is asserted for less than 4s, ACT8847 commences a soft-reset operation where nRSTO immediately asserts low, then remains asserted low until the nPBIN input is de-asserted and the reset time-out period expires. A status bit, SRSTAT[ ] , is set after a soft-reset event. The SRSTAT[ ] bit is automatically cleared to 0 after read. After Short Press, set WDSREN[ ] to 1 about 1s after nRSTO de-assert then clear WDSREN[ ] for properly shutdown sequence. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. nPBIN Manual Reset Detect Manual Reset Push-Button VIO nPBSTAT To CPU ACT8847 - 28 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 nRSTO Output nRSTO is an open-drain output which asserts low upon startup or when manual reset is asserted via the nPBIN input. When asserted on startup, nRSTO remains low until reset time-out period expires. When asserted due to manual-reset, nRSTO immediately asserts low, then remains asserted low until the nPBIN input is de-asserted and the reset time-out period expires. Connect a 10k or greater pull-up resistor from nRSTO to an appropriate voltage supply. nIRQ Output nIRQ is an open-drain output that asserts low any time an interrupt is generated. Connect a 10k or greater pull-up resistor from nIRQ to an appropriate voltage supply. nIRQ is typically used to drive the interrupt input of the system processor. Many of the ACT8847's functions support interruptgeneration as a result of various conditions. These are typically masked by default, but may be unmasked via the I2C interface. For more information about the available fault conditions, refer to the appropriate sections of this datasheet. Push-Button Control The ACT8847 is designed to initiate a system enable sequence when the nPBIN multi-function input is asserted. Once this occurs, a power-on sequence commences, as described below. The power-on sequence must complete and the microprocessor must take control (by asserting PWRHLD) before nPBIN is de-asserted. If the microprocessor is unable to complete its power-up routine successfully before the user releases the push-button, the ACT8847 automatically shuts the system down. This provides protection against accidental or momentary assertions of the pushbutton. If desired, longer "push-and-hold" times can be implemented by simply adding an additional time delay before asserting PWREN or PWRHLD. up routine is completed, the system remains enabled after the push-button is released as long as PWRHLD is asserted high. If the processor does not assert PWRHLD before the user releases the push-button, the boot-up sequence is terminated and all regulators are disabled. This provides protection against "false-enable", when the pushbutton is accidentally depressed, and also ensures that the system remains enabled only if the processor successfully completes the boot-up sequence. As with the enable sequence, a typical disable sequence is initiated when the user presses the push-button, which interrupts the processor via the nPBSTAT output. The actual disable sequence is completely software-controlled, but typically involved initiating various "clean-up" processes before the processor finally de-asserts PWRHLD. SLEEP Mode Sequence The ACT8847 supports S5PC210 / S5PV310 processors' SLEEP mode operation. Once a successful power-up routine has been completed, SLEEP mode may be initiated through a variety of software-controlled mechanisms. SLEEP mode is typically initiated when the user presses the push-button during normal operation. Pressing the push-button asserts the nPBIN input, which asserts the nPBSTAT output, which interrupts the processor. In response to this interrupt the processor should de-assert PWREN(XPWRRGTON), disabling REG2/3/4/5/8/9/10/11. PWRHLD should remain asserted during SLEEP mode so that REG1/6/7/12 remain enabled. The ACT8847 wakes up from SLEEP mode when either the push-button and/or PWREN (XPWRRGTON) is asserted. In either case, REG2/3/4/5/8/9/10/11 are enable which allow the system to resume normal operation. Control Sequences The ACT8847 features a variety of control sequences that are optimized for supporting system enable and disable, as well as SLEEP mode of the Samsung S5PC210 / S5PV310 processors. Enabling/Disabling Sequence A typical enable sequence is initiated whenever the nPBIN is asserted low via 50K resistance. The power control diagram is shown in Figure 3. During the boot sequence, the microprocessor must assert PWRHLD (XPSHOLD), and PWREN (XPWRRGTON), to ensure that the system remains powered after nPBIN is released. Once the power- Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 29 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Watch-Dog Supervision The ACT8847 features a watchdog supervisory function. An internal watchdog timer of 4s is unmasked by setting either WDSREN[ ] or WDPCEN [ ] bit to one. Once enabled, the watchdog timer is reset whenever there is I2C activity for the PMU. In the case where the system software stops responding and that there is no I2C transactions for 4s, the watchdog timer expires. As a result, the PMU either perform a soft-reset or power cycle, depending on whether WDSREN [ ] or WDPCEN [ ] is set. ACT8847 supports software-initiated power cycle. Once the SIPC[ ] bit is set, the PMU waits for 8ms and then initiate a power cycle to restart the entire system. Software-Initiated Power Cycle Figure 3: Power Control Sequence Sleep/Wakeup Sequence Enable Sequence Shutdown Sequence UVLO Main Battery OUT13 nPBIN 8ms 93% of VOUT6 (VDDALIVE) OUT6 OUT4 OUT 2/3/5 4ms 0.5ms 2ms 93% of VOUT2 93% of VOUT2 2ms 0.5ms OUT7 1ms OUT1 OUT12 2ms 2ms 2ms OUT11 93% of VOUT11 93% of VOUT11 0.5ms 0.5ms 1ms 1ms OUT10 OUT8 OUT9 2ms 2ms 60ms nRSTO PWREN PWRHLD Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 30 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Figure 4: ACT8847QM502-T Power Control Sequence for Freescale i.MX6 Platform. ACT8847QM502-T Shutdown Sequence Enable Sequence UVLO Main Power OUT13 nPBIN 2ms OUT9 OUT2 OUT1 OUT8 OUT10 93% of VOUT9 1ms 93% of VOUT2 0.5ms 93% of VOUT1 1ms 93% of VOUT8 0.5ms 93% of VOUT10 0.5ms OUT7 OUT4 93% of VOUT7 0.5ms 93% of VOUT4 1ms OUT3 40ms nRSTO PWRHLD PWREN Keep disable for REG5, REG6, REG11 and REG12, AP can turn on them through I2C if need. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 31 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 FUNCTIONAL DESCRIPTION I2C Interface The ACT8847 features an I2C interface that allows advanced programming capability to enhance overall system performance. To ensure compatibility with a wide range of system processors, the I2C interface supports clock speeds of up to 400kHz ("Fast-Mode" operation) and uses standard I2C commands. I2C write-byte commands are used to program the ACT8847, and I2C read-byte commands are used to read the ACT8847's internal registers. The ACT8847 always operates as a slave device, and is addressed using a 7-bit slave address followed by an eighth bit, which indicates whether the transaction is a readoperation or a write-operation, [1011010x]. Thermal Protection SDA is a bi-directional data line and SCL is a clock input. The master device initiates a transaction by issuing a START condition, defined by SDA transitioning from high to low while SCL is high. Data is transferred in 8-bit packets, beginning with the MSB, and is clocked-in on the rising edge of SCL. Each packet of data is followed by an "Acknowledge" (ACK) bit, used to confirm that the data was transmitted successfully. 2 For more information regarding the I C 2-wire serial interface, go to the NXP website: http://www.nxp.com. Housekeeping Functions Programmable battery Voltage Monitor The ACT8847 features a programmable batteryvoltage monitor, which monitors the voltage at INL2 (which should be connected directly to the battery) and compares it to a programmable threshold voltage. The VBATMON comparator is designed to be immune to noise resulting from switching, load transients, etc. The BATMON comparator is disable by default; to enable it, set the BATLEV[3:0] register to one of the value in Table 4. Note that there is a 200mV hysteresis between the rising and falling threshold for the comparator. The VBATDAT [-] bit reflects the output of the BATMON comparator. The value of VBATDAT[ ] is 1 when VINL2 < BATLEV; value is 0 otherwise. The VBATMON comparator can generate an interrupt when VINL2 is lower than BATLEV[ ] voltage. The interrupt is masked by default by can be unmasked by setting VBATMSK[ ] = 1. BATLEV[3:0] BATLEV Falling Threshold 0000 2.5 0001 2.6 0010 2.7 0011 2.8 0100 2.9 0101 3.0 0110 3.1 0111 3.2 1000 3.3 1001 3.4 1010 3.5 1011 3.6 1100 3.7 1101 3.8 1110 3.9 1111 4.0 The ACT8847 integrates thermal shutdown protection circuitry to prevent damage resulting from excessive thermal stress, as may be encountered under fault conditions. Thermal Interrupt If the thermal interrupt is unmasked (by setting nTMSK[ ] to 1), ACT8847 can generate an interrupt when the die temperature reaches 120C (typ). Thermal Protection If the ACT8847 die temperature exceeds 160C, the thermal protection circuitry disables all regulators and prevents the regulators from being enabled until the IC temperature drops by 20C (typ). Table 4: BATLEV Falling Threshold Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 32 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 STEP-DOWN DC/DC REGULATORS General Description REG1, REG2, REG3, and REG4 are fixed-frequency, current-mode, synchronous PWM step-down converters that achieves peak efficiencies of up to 97%. These regulators operate with a fixed frequency of 2.25MHz, minimizing noise in sensitive applications and allowing the use of small external components. Additionally, REG1, REG2, REG3, and REG4 are available with a variety of standard and custom output voltages, and may be softwarecontrolled via the I2C interface for systems that require advanced power management functions. 100% Duty Cycle Operation REG1, REG2, REG3, and REG4 are capable of operating at up to 100% duty cycle. During 100% duty cycle operation, the high-side power MOSFETs are held on continuously, providing a direct connection from the input to the output (through the inductor), ensuring the lowest possible dropout voltage in battery powered applications. Operating Mode By default, REG1, REG2, REG3, and REG4 operate in fixed-frequency PWM mode at medium to heavy loads, then transition to a proprietary power-saving mode at light loads in order to save power. Synchronous Rectification REG1, REG2, REG3, and REG4 each feature integrated synchronous rectifiers, maximizing efficiency and minimizing the total solution size and cost by eliminating the need for external rectifiers. Soft-Start REG1, REG2, REG3, and REG4 include internal 400 us soft-start ramps which limit the rate of change of the output voltage, minimizing input inrush current and ensuring that the output powers up in a monotonic manner that is independent of loading on the outputs. This circuitry is effective any time the regulator is enabled, as well as after responding to a short-circuit or other fault condition. Compensation REG1, REG2, REG3, and REG4 utilize current-mode control and a proprietary internal compensation scheme to simultaneously simplify external component selection and optimize transient performance over their full operating range. No compensation design is required; simply follow a few simple guide lines described below when choosing external components. induced upon the voltage source. A 10F ceramic capacitor is recommended for each regulator in most applications. Output Capacitor Selection REG1, REG2, REG3, and REG4 were designed to take advantage of the benefits of ceramic capacitors, namely small size and very-low ESR. REG1, REG2, REG3 and REG4 are designed to operate with 33uF or 44uF output capacitor over most of their output voltage ranges, although more capacitance may be desired depending on the duty cycle and load step requirements. Two of the most common dielectrics are Y5V and X5R. Whereas Y5V dielectrics are inexpensive and can provide high capacitance in small packages, their capacitance varies greatly over their voltage and temperature ranges and are not recommended for DC/DC applications. X5R and X7R dielectrics are more suitable for output capacitor applications, as their characteristics are more stable over their operating ranges, and are highly recommended. Inductor Selection REG1, REG2, REG3, and REG4 utilize current-mode control and a proprietary internal compensation scheme to simultaneously simplify external component selection and optimize transient performance over their full operating range. These devices were optimized for operation with 2.2H or 1H inductors. Choose an inductor with a low DCresistance, and avoid inductor saturation by choosing inductors with DC ratings that exceed the maximum output current by at least 30%. Configuration Options Output Voltage Programming By default, each regulator powers up and regulates to its default output voltage. For REG2, REG3 and REG4, the output voltage is selectable by setting corresponding VSEL pin that when VSEL is low, output voltage is programmed by VSET0[-] bits, and when VSEL is high, output voltage is programmed by VSET1[-] bits. Also, once the system is enabled, each regulator's output voltage may be independently programmed to a different value. Program the output voltages via the I2C serial interface by writing to the regulator's VSET0[-] register if VSEL is low or VSET1[-] register if VSEL is high as shown in Table 5. Input Capacitor Selection The input capacitor reduces peak currents and noise Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 33 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Enable / Disable Control During normal operation, each buck may be enabled or disabled via the I2C interface by writing to that regulator's ON[ ] bit. OK[ ] and Output Fault Interrupt Each DC/DC features a power-OK status bit that can be read by the system microprocessor via the I2C interface. If an output voltage is lower than the powerOK threshold, typically 7% below the programmed regulation voltage, that regulator's OK[ ] bit will be 0. If a DC/DC's nFLTMSK[-] bit is set to 1, the ACT8847 will interrupt the processor if that DC/DC's output voltage falls below the power-OK threshold. In this case, nIRQ will assert low and remain asserted until either the regulator is turned off or back in regulation, and the OK[ ] bit has been read via I2C. Step-down DC/DCs exhibit discontinuous input current, so the input capacitors should be placed as close as possible to the IC, and avoiding the use of via if possible. The inductor, input filter capacitor, and output filter capacitor should be connected as close together as possible, with short, direct, and wide traces. The ground nodes for each regulator's power loop should be connected at a single point in a starground configuration, and this point should be connected to the backside ground plane with multiple via. The output node for each regulator should be connected to its corresponding OUTx pin through the shortest possible route, while keeping sufficient distance from switching nodes to prevent noise injection. Finally, the exposed pad should be directly connected to the backside ground plane using multiple via to achieve low electrical and thermal resistance. PCB Layout Considerations High switching frequencies and large peak currents make PC board layout an important part of step-down DC/DC converter design. A good design minimizes excessive EMI on the feedback paths and voltage gradients in the ground plane, both of which can result in instability or regulation errors. Table 5: REGx/VSET[ ] Output Voltage Setting REGx/VSET[2:0] REGx/VSET[5:3] 000 001 010 011 100 101 110 111 000 0.600 0.800 1.000 1.200 1.600 2.000 2.400 3.200 001 0.625 0.825 1.025 1.250 1.650 2.050 2.500 3.300 010 0.650 0.850 1.050 1.300 1.700 2.100 2.600 3.400 011 0.675 0.875 1.075 1.350 1.750 2.150 2.700 3.500 100 0.700 0.900 1.100 1.400 1.800 2.200 2.800 3.600 101 0.725 0.925 1.125 1.450 1.850 2.250 2.900 3.700 110 0.750 0.950 1.150 1.500 1.900 2.300 3.000 3.800 111 0.775 0.975 1.175 1.550 1.950 2.350 3.100 3.900 Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 34 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 LOW-NOISE, LOW-DROPOUT LINEAR REGULATORS General Description ACT8847 features eight low-noise, low-dropout linear regulators (LDOs) that supply up to 350mA. Three of these LDOs (REG10, REG11, and REG12) supports extended input voltage range down to 1.7V. Each LDO has been optimized to achieve low noise and high-PSRR. Output Current Limit Each LDO contains current-limit circuitry featuring a current-limit fold-back function. During normal and moderate overload conditions, the regulators can support more than their rated output currents. During extreme overload conditions, however, the current limit is reduced by approximately 30%, reducing power dissipation within the IC. Compensation The LDOs are internally compensated and require very little design effort, simply select input and output capacitors according to the guidelines below. Input Capacitor Selection Each LDO requires a small ceramic input capacitor to supply current to support fast transients at the input of the LDO. Bypassing each INL pin to GA with 1F. High quality ceramic capacitors such as X7R and X5R dielectric types are strongly recommended. Output Capacitor Selection Each LDO requires a small 2.2F ceramic output capacitor for stability . For best performance, each output capacitor should be connected directly between the output and GA pins, as close to the output as possible, and with a short, direct connection. High quality ceramic capacitors such as X7R and X5R dielectric types are strongly recommended. Configuration Options Output Voltage Programming By default, each LDO powers up and regulates to its default output voltage. Once the system is enabled, each output voltage may be independently programmed to a different value by writing to the regulator's VSET[-] register via the I2C serial interface as shown in Table 5. Each of the LDOs features an optional output discharge function, which discharges the output to ground through a 1.5k resistance when the LDO is disabled. This feature may be enabled or disabled by setting DIS[-]; set DIS[-] to 1 to enable this function, clear DIS[-] to 0 to disable it. OK[ ] and Output Fault Interrupt Each LDO features a power-OK status bit that be read by the system microprocessor via interface. If an output voltage is lower than power-OK threshold, typically 11% below programmed regulation voltage, the value of regulator's OK[-] bit will be 0. can the the the that If a LDO's nFLTMSK[-] bit is set to 1, the ACT8847 will interrupt the processor if that LDO's output voltage falls below the power-OK threshold. In this case, nIRQ will assert low and remain asserted until either the regulator is turned off or back in regulation, and the OK[-] bit has been read via I2C. PCB Layout Considerations The ACT8847's LDOs provide good DC, AC, and noise performance over a wide range of operating conditions, and are relatively insensitive to layout considerations. When designing a PCB, however, careful layout is necessary to prevent other circuitry from degrading LDO performance. A good design places input and output capacitors as close to the LDO inputs and output as possible, and utilizes a star-ground configuration for all regulators to prevent noise-coupling through ground. Output traces should be routed to avoid close proximity to noisy nodes, particularly the SW nodes of the DC/DCs. REFBP is a noise-filtered reference, and internally has a direct connection to the linear regulator controller. Any noise injected onto REFBP will directly affect the outputs of the linear regulators, and therefore special care should be taken to ensure that no noise is injected to the outputs via REFBP. As with the LDO output capacitors, the REFBP bypass capacitor should be placed as close to the IC as possible, with short, direct connections to the star-ground. Avoid the use of via whenever possible. Noisy nodes, such as from the DC/DCs, should be routed as far away from REFBP as possible. Enable / Disable Control During normal operation, each LDO may be enabled or disabled via the I2C interface by writing to that LDO's ON[ ] bit. Output Discharge Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 35 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 ALWAYS-ON LDO (REG13) General Description REG13 is an always-on, low-dropout linear regulator (LDO) that is optimized for RTC and backup-battery applications. REG13 features lowquiescent supply current, current-limit protection, and reverse-current protection, and is ideally suited for always-on power supply applications, such as for a real-time clock, or as a backup-battery or super-cap charger. Reverse-Current Protection REG13 features internal circuitry that limits the reverse supply current to less than 1A when the input voltage falls below the output voltage, as can be encountered in backup-battery charging applications. REG13's internal circuitry monitors the input and the output, and disconnects internal circuitry and parasitic diodes when the input voltage falls below the output voltage, greatly minimizing backup battery discharge. Typical Application Voltage Regulators REG13 is ideally suited for always-on voltageregulation applications, such as for real-time clock and memory keep-alive applications. This regulator requires only a small ceramic capacitor with a minimum capacitance of 0.47F for stability. For best performance, the output capacitor should be connected directly between the output and GA, with a short and direct connection. Figure 5: Typical Application of RTC LDO Backup Battery Charging ACT8847 OUT13 RTC Supper cap or Back- up battery REG13 features a constant current-limit, which protects the IC under output short-circuit conditions as well as provides a constant charge current, when operating as a backup battery charger. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 36 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 PWM LED DRIVERS The GPIO3, the GPIO4, the GPIO5, and the GPIO6 are configured as PWM LED drivers, which could support up to 6mA current with programmable frequency and duty cycle. Set PWMxEN[ ] bit to "1" to enable PWM function of GPIOx. GPIOx/DUTY[ ] PWM Frequency Setting PWM Frequence Selection Each LED driver may be independently programmed to a different frequency by writing to the GPIO's FRE[2:0] register via the I2C serial interface as shown in Table 6. Table 6: GPIOx/FRE[ ] PWM Frequency Setting GPIOx/FRE[2:0] PWM Frequency [Hz] 000 0.25 001 0.5 010 1 011 2 100 128 101 256 PWM Duty Cycle Selection Each LED driver may be independently programmed to a different duty cycle by writing to the GPIO's DUTY[3:0] register via the I2C serial interface as shown in Table 7. GPIOx/DUTY[3:0] PWM Duty Cycle [%] 0000 6.25 0001 12.5 0010 18.75 0011 25 0100 31.25 0101 37.5 0110 43.75 0111 50 1000 56.25 1001 62.5 1010 68.75 1011 75 1100 81.25 1101 87.5 1110 93.75 1111 100 Table 7: Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 37 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 CMI OPTIONS This section provides the basic default configuration settings for the ACT8847 CMI options. Refer to each option's application note for the comprehensive list of default settings. CMI 102: ACT8847QM102-T CMI 102 is optimized for iMX6UL/iMX6ULL processors. REG6, REG8, REG9, REG10, REG11, and REG12 are not enabled by default with this CMI, but can be enabled via I2C. Typical connections to the iMX6UL are shown below. ACT8846 Regulator REG1 Voltage iMX6UL Function iMX6UL Pins 1.35V DDR3L Supply NVCC_DRAM REG2 3.3V GPIO Supplies NVCC_xxxx REG3 3.8V System Supply n/a REG4 1.3V Core Supply VDD_SOC_IN REG5 3.3V n/a REG7 3.3V System Supply for startup sequencing VDD High Supply REG13 3.3V Secure NVM Storage Supply VDD_SNVS_IN VDD_HIGH_IN Sequencing Rail VSET0 Voltage (V) VSET1 Voltage (V) Sequencing Input Trigger StartUp Delay (us) SoftStart (us) VIN 5 5 n/a n/a n/a REG13 3.3 3.3 VIN_UVLO 400 400 REG7 3.3 3.3 GPIO1 32000 100 REG1 1.35 1.35 OUT7 2000 400 REG4 1.3 1.3 OUT1 2000 400 REG2 3.3 3.3 OUT4 2000 400 REG5 3.3 3.3 OUT2 0 100 REG3 3.8 3.8 2000 400 REG6 off off PWREN AND PWRHLD n/a n/a n/a REG8 off off n/a n/a n/a REG9 off off n/a n/a n/a REG10 off off n/a n/a n/a REG11 off off n/a n/a n/a REG12 off off n/a n/a n/a Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 38 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Hardware Configuration The following hardware connections are required to achieve the specified startup sequencing. Connect a 2.2uF capacitor between GPIO1 and GPIO2 Connect a 1Mohm resistor from GPIO2 to GA. Connect a 51kohm resistor between GPIO3 and nPBIN. Connect a 10kohm resistor between REG7 and PWRHLD. Startup The ACT8847QM102-T has three startup sequences. REG13. When power is applied to the IC. REG13 automatically turns on when input power is applied and the input voltage is above UVLO. REG7/1/4/2/5. REG7/1/4/2/5 turn on when GPIO1 is pulled high. REG7/1/4/2/5 are latched on after REG7 goes into regulation and pulls PWRHLD high. GPIO1 may remain high or return to a logic low after this time. REG7/1/4/2/5 stay on in either case. REG3. The enable input for REG3 is the AND of PWRHLD and PWREN. Note that PWRHLD should be connected to REG7. REG3 is intended to be turned on after REG7/1/4/2/5 are in regulation. Once REG7/1/4/2/5 are in regulation and PWRHLD is high, REG3 can be independently enabled and disabled with PWREN. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 39 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Shutdown REG3 shuts down when either PWREN or PWRHLD go low. REG7/1/4/2/5 shut down by pressing nPBIN for longer than 4s or by pulling PWRHLD low while GPIO1 is low. nPBIN nPBIN retains the short and long press functionality described earlier in the datasheet. A "short press" pulls nRSTO low to reset the processor. A "long press" powers down all outputs. The outputs restart per the defined sequencing when nPBIN is released after a "long press" NRSTO nRSTO is gated by REG5 and should be pulled up to REG5. nRSTO has a 40ms delay after REG5 goes into regulation. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 40 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 CMI 103 CMI 103 is optimized for iMX6UL/iMX6ULL processors. REG6, REG10, REG11, and REG12 are not enabled by default with this CMI, but can be enabled via I2C. CMI 103 is similar to CMI 102. The difference is that CMI 103 has REG8 and REG9 enabled by default and that the turn-on delays are 1ms instead of 2ms. Typical connections to the iMX6UL are shown below. REG8 and REG9 power additional non-iMX6UL circuitry. ACT8846 Regulator REG1 Voltage iMX6UL Function iMX6UL Pins 1.35V DDR3L Supply NVCC_DRAM REG2 3.3V GPIO Supplies NVCC_xxxx REG3 3.8V System Supply n/a REG4 1.3V Core Supply VDD_SOC_IN REG5 3.3V n/a REG7 3.3V System Supply for startup sequencing VDD High Supply REG8 3.3V External circuitry n/a REG9 3.1V External circuitry n/a REG13 3.3V Secure NVM Storage Supply VDD_SNVS_IN VDD_HIGH_IN Sequencing Rail VSET0 Voltage (V) VSET1 Voltage (V) Sequencing Input Trigger StartUp Delay (us) SoftStart (us) VIN 5 5 n/a n/a n/a REG13 3.3 3.3 VIN_UVLO 400 400 REG7 3.3 3.3 GPIO1 32000 100 REG1 1.35 1.35 OUT7 1000 400 REG4 1.3 1.3 OUT1 1000 400 REG2 3.3 3.3 OUT4 1000 400 REG5 3.3 3.3 OUT2 0 100 REG8 3.3 n/a OUT5 1000 100 REG9 3.1 n/a OUT3 1000 100 REG3 3.8 3.8 2000 400 REG6 off n/a PWREN AND PWRHLD n/a n/a n/a REG10 off n/a n/a n/a n/a REG11 off n/a n/a n/a n/a REG12 off n/a n/a n/a n/a Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 41 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Hardware Configuration The following hardware connections are required to achieve the specified startup sequencing. Connect a 2.2uF capacitor between GPIO1 and GPIO2 Connect a 1Mohm resistor from GPIO2 to GA. Connect a 51kohm resistor between GPIO3 and nPBIN. Connect a 10kohm resistor between REG7 and PWRHLD. Startup The ACT8847QM103-T has three startup sequences. REG13. When power is applied to the IC. REG13 automatically turns on when input power is applied and the input voltage is above UVLO. REG7/1/4/2/5/8/9. REG7/1/4/2/5 turn on when GPIO1 is pulled high. REG7/1/4/2/5/8/9 are latched on after REG7 goes into regulation and pulls PWRHLD high. GPIO1 may remain high or return to a logic low after this time. REG7/1/4/2/5/8/9 stay on in either case. REG3. The enable input for REG3 is the AND of PWRHLD and PWREN. Note that PWRHLD should be connected to REG7. REG3 is intended to be turned on after REG7/1/4/2/5/8/9 are in regulation. Once REG7/1/4/2/5/8/9 are in regulation and PWRHLD is high, REG3 can be independently ena- Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 42 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 Shutdown REG3 shuts down when either PWREN or PWRHLD go low. REG7/1/4/2/5/8/9 shut down by pressing nPBIN for longer than 4s or by pulling PWRHLD low while GPIO1 is low. nPBIN nPBIN retains the short and long press functionality described earlier in the datasheet. A "short press" pulls nRSTO low to reset the processor. A "long press" powers down all outputs. The outputs restart per the defined sequencing when nPBIN is released after a "long press" nRSTO Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 43 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 TQFN66-48 PACKAGE OUTLINE AND DIMENSIONS D D/2 SYMBOL A E/2 A1 E DIMENSION IN INCHES MIN MAX MIN MAX 0.700 0.800 0.032 0.036 0.200 REF 0.008 REF A2 0.000 0.050 0.000 0.002 b 0.150 0.250 0.006 0.010 D 6.00 0.24 E 6.00 0.24 D2 4.15 4.40 0.166 0.176 E2 4.15 4.40 0.166 0.176 e L R A DIMENSION IN MILLIMETERS 0.400 BSC 0.300 0.500 0.300 0.016 BSC 0.012 0.020 0.012 A1 A2 D2 b L e E2 R Active-Semi, Inc. reserves the right to modify the circuitry or specifications without notice. Users should evaluate each product to make sure that it is suitable for their applications. Active-Semi products are not intended or authorized for use as critical components in life-support devices or systems. Active-Semi, Inc. does not assume any liability arising out of the use of any product or circuit described in this datasheet, nor does it convey any patent license. Active-Semi and its logo are trademarks of Active-Semi, Inc. For more information on this and other products, contact sales@active-semi.com or visit http://www.active-semi.com. is a registered trademark of Active-Semi. Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. - 44 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc. ACT8847 / ACT8849 Rev 10.0 09-Aug-2018 REVISION HISTORY REVISION DATE 8 17-Jan-2017 1. Added OPN ACT8847QM503 9 27-Jun-2017 1.Added OPN ACT8847QM102 10 08-Aug-2018 1.Added OPN ACT8847QM103 2.Added INL2 requirement 3.Updated ACT8847QM102 startup picture Innovative PowerTM ActivePMUTM is a trademark of Active-Semi. I2CTM is a trademark of NXP. DESCRIPTION - 45 - www.active-semi.com Copyright (c) 2015-2018 Active-Semi, Inc.