Devices
Part Number HDSP- Color Description Front View
0781 High-Efficiency Red Numeric, Right Hand DP A
0782 Low Power Numeric, Left Hand DP B
0783 Over Range ±1C
0784 Hexadecimal D
0791 High-Efficiency Red Numeric, Right Hand DP A
0792 High Brightness Numeric, Left Hand DP B
0793 Over Range ±1C
0794 Hexadecimal D
0881 Yellow Numeric, Right Hand DP A
0882 Numeric, Left Hand DP B
0883 Over Range ±1C
0884 Hexadecimal D
0981 High-Performance Green Numeric, Right Hand DP A
0982 Numeric, Left Hand DP B
0983 Over Range ±1C
0984 Hexadecimal D
HDSP-078x
HDSP-079x
HDSP-088x
HDSP-098x
Features
• Three Character Options
Numeric, Hexadecimal, Over
Range
• Three Colors
High Efficiency Red, Yellow,
High Performance Green
• 4 x 7 Dot Matrix Character
• High Efficiency Red, Yellow
and High Performance Green
• Two High Efficiency Red
Options
Low Power, High Brightness
• Performance Guaranteed
Over Temperature
• High Temperature Stabilized
• Memory Latch/Decoder/
Driver
TTL Compatible
• Categorized for Luminous
Intensity
Description
These standard solid state displays
have a 7.4 mm (0.29 inch) dot
matrix character and an on-board
IC with data memory latch/
decoder and LED drivers in a
glass/ceramic package.
The hermetic HDSP-078x,-079x/
-088x displays utilize a solder
glass frit seal. The HDSP-098X
displays utilize an epoxy glass-to-
ceramic seal.
The numeric devices decode posi-
tive BCD logic into characters
“0-9,” a “–” sign, decimal point,
and a test pattern. The
hexadecimal devices decode
Glass/Ceramic Numeric and
Hexadecimal Displays for
Industrial Applications
Technical Data
positive BCD logic into 16
characters, “0-9, A-F.” An input is
provided on the hexadecimal
devices to blank the display (all
LEDS off) without losing the
contents of the memory.
The over range device displays
±1” and right hand decimal
point and is typically driven via
external switching transistors.
2
Figure 1. Timing Diagram.
Figure 2. Block Diagram.
SYYWW
COUNTRY CODE
Package Dimensions
3
Optical Characterstics at TA = 25°C, VCC = 5.0 V
Device Description Symbol Min. Typ. Max. Unit
HDSP-078x Series Luminous Intensity per LED IV65 140 µcd
(Digit Average)[3,4]
Peak Wavelength λPEAK 635 nm
Dominant Wavelength[5] λd626 nm
HDSP-079x Series Luminous Intensity per LED IV260 620 µcd
(Digit Average)[3,4]
Peak Wavelength λPEAK 635 nm
Dominant Wavelength[5] λd626 nm
HDSP-088x Series Luminous Intensity per LED IV215 490 µcd
(Digit Average)[3,4]
Peak Wavelength λPEAK 583 nm
Dominant Wavelength[5,6] λd585 nm
HDSP-098x Series Luminous Intensity per LED IV298 1100 µcd
(Digit Average)[3,4]
Peak Wavelength λPEAK 568 nm
Dominant Wavelength λd574 nm
Absolute Maximum Ratings
Description Symbol Min. Max. Unit
Storage Temperature, Ambient
HDSP-078x/-079x/-088x TS-65 +125 °C
HDSP-098x -55 +100
Operating Temperature, Ambient[1] TA-55 +100 °C
Supply Voltage[2] VCC -0.5 +7.0 V
Voltage Applied to Input Logic, dp and Enable Pins VI, VDP, VE-0.5 VCC V
Voltage Applied to Blanking Input[2] VR-0.5 VCC V
Maximum Solder Temperature at 1.59 mm (0.062 inch) 260 °C
Below Seating Plane; t 5 Seconds
Notes:
1. The nominal thermal resistance of a display mounted in a socket that is soldered onto a printed circuit board is
RθJA =50°C/W/device. The device package thermal resistance is RθJ-PIN = 15°C/W/device. The thermal resistance device pin-to-
ambient through the PC board should not exceed 35°C/W/device for operation up to T
A = +100°C.
2. Voltage values are with respect to device ground, pin 6.
3. These displays are categorized for luminous intensity with the intensity category designated by a letter code located on the back of
the display package. Case temperature of the device immediately prior to the light measurement is equal to 25°C.
Recommended Operating Conditions
Description Symbol Min. Nom. Max. Unit
Supply Voltage[2] VCC 4.5 5.0 5.5 V
Operating Temperature, Ambient[1] TA–55 +100 °C
Enable Pulse Width tW100 nsec
Time Data Must Be Held Before Positive tSETUP 50 nsec
Transition of Enable Line
Time Data Must Be Held After Positive tHOLD 50 nsec
Transition of Enable Line
Enable Pulse Rise Time tTLH 1.0 msec
4
Electrical/Optical Characteristics
TA = –55°C to +100°C
Description Symbol Test Conditions Min. Typ.[7] Max. Unit
Supply HDSP-078x Series ICC VCC = 5.5 V 78 105 mA
Current HDSP-079x/-088x/ Characters “5.” or
-098x Series “B” displayed
Power HDSP-078x Series PTVCC = 5.5 V 390 573 mW
Dissipation HDSP-079x/-088x/ Characters “5.” or
-098x Series “B” displayed
Logic, Enable and Blanking VIL VCC = 4.5 V 0.8 V
Low-Level Input Voltage
Logic, Enable High-Level Input VIH 2.0 V
Voltage
Blanking High-Voltage; Display VBH 2.3 V
Blanked
Logic and Enable Low-Level IIL VCC = 5.5 V –1.6 mA
Input Current
Blanking Low-Level Input Current IBL VIL = 0.4 V –10 µA
Logic, Enable and Blanking IIH VCC = 5.5 V +40 µA
High-Level Input Current VIH = 2.4 V
Weight 1.0 gm
Leak Rate 5 x 10-8 cc/sec
120 175
690 963
Notes:
4. The luminous intensity at a specific operating ambient
temperature, Iv(TA), may be approximated from the following
exponential equation: Iv(TA)=I
v
(25°C) e[k(T -25°C)].
Device K
HDSP-078 Series 0.0131/°C
HDSP-079x Series
HDSP-088x Series 0.0112/°C
HDSP-098x Series 0.0104/°C
5. The dominant wavelength, λd, is derived from the CIE chroma-
ticity diagram and represents the single wavelength which
defines the color of the device.
6. The HDSP-088X and HDSP-098X series devices are categor-
ized as to dominant wavelength with the category designated
by a number on the back of the display package.
7. All typical values at VCC = 5.0 V and TA = 25°C.
Operational
Considerations
Electrical
These devices use a modified
4 x 7 dot matrix of light emitting
diodes to display decimal/
hexadecimal numeric informa-
tion. The high efficiency red and
yellow displays use GaAsP/GaP
LEDs and the high performance
green displays use GaP/GaP
LEDs. The LEDs are driven by
constant current drivers, BCD
information is accepted by the
display memory when the enable
line is at logic low and the data is
latched when the enable is at
logic high. Using the enable pulse
width and data setup and hold
times listed in the Recommended
Operating Conditions allows data
to be clocked into an array of
displays at a 6.7 MHz rate.
The decimal point input is active
low true and this data is latched
into the display memory in the
same fashion as the BCD data.
The decimal point LED is driven
by the on-board IC.
The blanking control input on the
hexadecimal displays blanks
(turns off) the displayed
information without disturbing
the contents of display memory.
The display is blanked at a
minimum threshold level of 2.0
volts. When blanked, the display
standby power is nominally 250
mW at TA = 25°C.
The ESD susceptibility of the IC
devices is Class A of MIL-STD-
883 or Class 2 of DOD-STD-1686
and DOD-HDBK-263.
A
5
Mechanical
These displays are hermetically
sealed for use in environments
that require a high reliability
device. These displays are
designed and tested to meet a
helium leak rate of
5x10
-8 cc/sec.
These displays may be mounted
by soldering directly to a printed
circuit board or insertion into a
socket. The lead-to-lead pin
spacing is 2.54 mm (0.100 inch)
and the lead row spacing is 15.24
mm (0.600 inch). These displays
may be end stacked with 2.54
mm (0.100 inch) spacing
between outside pins of adjacent
displays. Sockets such as Augat
324-AG2D (3 digits) or Augat
508-AG8D (one digit, right angle
mounting) may be used.
The primary thermal path for
power dissipation is through the
device leads. Therefore, to insure
reliable operation up to an
ambient temperature of +100°C,
it is important to maintain a
base-to-ambient thermal
resistance of less than
35°C watt/device as measured on
top of display pin 3.
For further information on
soldering and post solder
cleaning, see Application Note
1027, Soldering LED
Components.
Preconditioning
These displays are 100% pre-
conditioned by 24 hour storage at
125°C, at 100°C for the HDSP-
098x Series.
Contrast Enhancement
These display devices are
designed to provide an optimum
ON/OFF contrast when placed
behind an appropriate contrast
enhancement filter. For further
information on contrast
enhancement, see Application
Note 1015, Contrast
Enhancement for LED
Displays.
Over Range Display
The over range devices display
±1” and decimal point. The
character height and package
configuration are the same as the
numeric and hexadecimal
devices. Character selection is
obtained via external switching
transistors and current limiting
resistors.
Absolute Maximum Ratings
Description Symbol Min Max Unit
Storage Temperature, Ambient TS65 +125 °C
Operating Temperature, Ambient TA55 +100 °C
Forward Current, Each LED IF10 mA
Reverse Voltage, Each LED VR5V
6
Package Dimensions
Luminous Intensity per LED
(Digit Average) at TA = 25°C
Device Test Conditions Min. Typ. Units
HDSP-0783 IF = 2.8 mA 65 140 µcd
IF = 8 mA 620 µcd
HDSP-0883 IF = 8 mA 215 490 µcd
HDSP-0983 IF = 8 mA 298 1100 µcd
Recommended Operating Conditions
VCC = 5.0 V
Forward Resistor Value
Current Per
Device LED, mA R1R2R3
HDSP-0783 Low Power 2.8 1300 200 300
High Brightness 8 360 47 68
HDSP-0883 8 360 36 56
HDSP-0983 8 360 30 43
Figure 3. Typical Driving Circuit.
Pin
Character 1 2,3 4 8
+1XX1
–0XX1
1X1XX
Decimal Point X X 1 X
Blank 0 0 0 0
Notes:
0: Line switching transistor in Figure 7 cutoff.
1: Line switching transistor in Figure 7 saturated.
X: ‘don’t care.’
7
Bin Category Min. (mcd) Max. (mcd) Condition
A 0.065 0.102
B 0.085 0.138
C 0.114 0.200
D 0.165 0.300
E 0.260 0.488
F 0.403 0.756
G 0.625 1.172
Intensity Bin Limits for HDSP-078x Series
Luminous
Intensity
per LED.
VDD @ 5.0 V
Bin Category Min. (mcd) Max. (mcd) Condition
A 0.22 0.34
B 0.28 0.46
C 0.38 0.66
D 0.55 0.99
E 0.82 1.54
F 1.27 2.39
Intensity Bin Limits for HDSP-088x Series
Luminous
Intensity
per LED.
VDD @ 5.0 V
Electrical Characteristics
TA = –55°C to +100°C
Device Description Symbol Test Conditions Min Typ Max Unit
HDSP-0783 Power Dissipation PTIF = 2.8 mA 72 mW
IF = 8 mA 224 282
Forward Voltage per LED VFIF = 2.8 mA 1.6 V
IF = 8 mA 1.75 2.2
HDSP-0883 Power Dissipation PTIF = 8 mA 237 282 mW
(All LEDs Illuminated)
Forward Voltage per LED VF1.90 2.2 V
HDSP-0883 Power Dissipation PTIF = 8 mA 243 282 mW
(All LEDs Illuminated)
Forward Voltage per LED VF1.85 2.2 V
(All LEDs Illuminated)
Bin Category Min. (mcd) Max. (mcd) Condition
E 0.260 0.488
F 0.403 0.756
G 0.625 1.172
H 0.969 1.820
Intensity Bin Limits for HDSP-079x Series
Luminous
Intensity
per LED.
VDD @ 5.0 V
Bin Category Min. (mcd) Max. (mcd) Condition
C 0.30 0.52
D 0.43 0.79
E 0.65 1.18
F 0.97 1.76
G 1.45 2.63
Intensity Bin Limits for HDSP-098x Series
Luminous
Intensity
per LED.
VDD @ 5.0 V
www.semiconductor.agilent.com
Data subject to change.
Copyright © 2001 Agilent Technologies, Inc.
September 20, 2001
Obsoletes 5964-6390E (11/99)
5988-2261EN
Intensity Range (nm)
Color Bin Min. Max.
Yellow 1 581.50 585.00
2 584.00 587.50
3 586.50 590.00
Green 1 570.00 574.00
2 573.00 577.00
3 576.00 580.00
Note:
Bin categories are established for classification of products. Products
may not be available in all bin categories. Please consult your local
Agilent Technologies representative.
Color Bin Limits (Dominant Wavelength)