SPEC NO: DSAN2798 REV NO: V.1A DATE: OCT/15/2013 PAGE: 1 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203014043
2.1x0.6mm RIGHT ANGLE SURFACE LED
LAMP
Part Number: APA2106SECK/J3-PRV Hyper Red
Features
z2.1mmX0.6mm right angle SMT LED, 1.0mm thickness.
zLow power consumption.
zWide viewing angle.
zIdeal for backlight and indicator.
zVarious colors and lens types available.
zPackage: 2000pcs / reel.
zMoisture sensitivity level : level 3.
zTinned pads for improved solderability.
zRoHS compliant.
Description
The Hyper Red device is based on light emitting diode chip
made from AlGaInP.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2.Tolerance is ±0.1(0.004") unless otherwise noted.
3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications
SPEC NO: DSAN2798 REV NO: V.1A DATE: OCT/15/2013 PAGE: 2 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203014043
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
Iv (mcd) [2]
@ 20mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
APA2106SECK/J3-PRV Hyper Red (AlGaInP) Water Clear
700 1100
*200 *380
120°
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Hyper Red 640 nm IF=20mA
λD [1] Dominant Wavelength Hyper Red 625 nm IF=20mA
Δλ1/2 Spectral Line Half-width Hyper Red 20 nm IF=20mA
C Capacitance Hyper Red 27 pF VF=0V;f=1MHz
VF [2] Forward Voltage Hyper Red 2.2 2.8 V IF=20mA
IR Reverse Current Hyper Red 10 uA VR=5V
Parameter Hyper Red Units
Power dissipation 84 mW
DC Forward Current 30 mA
Peak Forward Current [1] 150 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
SPEC NO: DSAN2798 REV NO: V.1A DATE: OCT/15/2013 PAGE: 3 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203014043
Hyper Red APA2106SECK/J3-PRV
SPEC NO: DSAN2798 REV NO: V.1A DATE: OCT/15/2013 PAGE: 4 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203014043
APA2106SECK/J3-PRV
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAN2798 REV NO: V.1A DATE: OCT/15/2013 PAGE: 5 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203014043
PACKING & LABEL SPECIFICATIONS APA2106SECK/J3-PRV
Terms and conditions for the usage of this document
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
