TD62064APG/AFG TOSHIBA Bipolar Digital Integrated Circuit Silicon Monolithic TD62064APG, TD62064AFG 4ch High-Current Darlington Sink Driver The TD62064APG/AFG are high-voltage, high-current darlington drivers comprised of four NPN darlington pairs. All units feature integral clamp diodes for switching inductive loads. Applications include relay, hammer, lamp and stepping motor drivers. TD62064APG Features * Output current (single output) 1.5 A (max) * High sustaining voltage output 50 V (min) * Output clamp diodes * Input compatible with TTL and 5 V CMOS * GND terminal = Heat sink * Package type-APG: DIP-16 pin * Package type-AFG: HSOP-16 pin TD62064AFG Pin Assignment (top view) TD62064APG Heat sink & GND Weight DIP16-P-300-2.54A: 1.11 g (typ.) HSOP16-P-300-1.00: 0.50 g (typ.) O4 NC I4 I3 NC O3 16 15 14 13 12 11 10 9 1 COM 2 O1 3 I1 4 5 6 I2 7 O2 8 COM Heat sink & GND TD62064AFG O4 NC I4 NC 16 15 14 13 1 COM 2 O1 3 I1 4 NC Heat sink & GND Heat sink & GND NC I3 NC O3 12 11 10 9 5 NC 6 I2 7 O2 8 COM 1 2011-01-14 TD62064APG/AFG Schematics (each driver) COMMON Output 8.2 k 1.1 k 230 Input GND Note: The input and output parasitic diodes cannot be used as clamp diodes. Precautions for Using (1) This IC does not include built-in protection circuits for excess current or overvoltage. If this IC is subjected to excess current or overvoltage, it may be destroyed. Hence, the utmost care must be taken when systems which incorporate this IC are designed. Utmost care is necessary in the design of the output line, COMMON and GND line since IC may be destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding. (2) This IC is being used to drive an inductive load (such as a motor, solenoid or relay), Toshiba recommends that the diodes (pins 1 and 8) be connected to the secondary power supply pin so as to absorb the counter electromotive force generated by the load. Please adhere to the device's absolute maximum ratings. Toshiba recommends that zener diodes be connected between the diodes (pins 1 and 8) and the secondary power supply pin (as the anode) so as to enable rapid absorption of the counter electromotive force. Again, please adhere to the device's absolute maximum ratings. Absolute Maximum Ratings (Ta = 25C) Characteristics Symbol Rating Unit VCE (SUS) -0.5 to 50 V IOUT 1.5 A/ch Input current IIN 50 mA Input voltage VIN -0.5 to 17 V Clamp diode reverse voltage VR 50 V Clamp diode forward current IF 1.5 A Output sustaining voltage Output current Power dissipation APG AFG PD 1.47/2.7 (Note 1) 0.9/1.4 (Note 2) W Operating temperature Topr -40 to 85 C Storage temperature Tstg -55 to 150 C Note 1: On glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) Note 2: On glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) 2 2011-01-14 TD62064APG/AFG Operating Conditions (Ta = -40 to 85C) Symbol Test Condition Min Typ. Max Unit VCE (SUS) 0 50 V 0 1250 Duty = 10% 0 1250 4 circuits Duty = 50% 0 390 Tj = 120C Duty = 10% 0 907 Duty = 50% 0 172 0 8 2.5 8 Characteristics Output sustaining voltage DC1 circuit, Ta = 25C Output current APG (Note 1) tpw = 25 ms IOUT AFG (Note 2) Ta = 85C VIN Input voltage IOUT = 1.25 A mA/ch V Output ON VIN (ON) Output OFF VIN (OFF) 0 0.4 Input current IIN 0 20 mA Clamp diode reverse voltage VR 0 50 V Clamp diode forward current IF 1.25 A Power dissipation APG PD AFG Ta = 85C (Note 1) 1.4 Ta = 85C (Note 2) 0.7 Min Typ. Max W Note 1: On glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) Note 2: On glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) Electrical Characteristics (Ta = 25C) Symbol Test Circuit ICEX 1 Output saturation voltage VCE (sat) 2 DC current transfer ratio hFE 2 VCE = 2 V Input voltage (output on) VIN (ON) 3 Clamp diode leakage current IR 4 Clamp diode forward voltage VF Input capacitance Characteristics Test Condition Unit VCE = 50 V, Ta = 25C 50 VCE = 50 V, Ta = 85C 500 IOUT = 1.25 A, IIN = 2 mA 1.6 IOUT = 0.75 A, IIN = 935 A 1.25 IOUT = 1.0 A 800 IOUT = 1.25 A 1500 IOUT = 1.25 A, IIN = 2 mA 2.4 VR = 50 V, Ta = 25C 50 VR = 50 V, Ta = 85C 100 5 IF = 1.25 A 2.0 V CIN 6 VIN = 0 V, f = 1 MHz 15 pF Turn-ON delay tON 7 CL = 15 pF, VOUT = 50 V, RL = 42 0.1 s Turn-OFF delay tOFF 7 CL = 15 pF, VOUT = 50 V, RL = 42 1.0 s Output leakage current 3 A V V A 2011-01-14 TD62064APG/AFG Test Circuit 1. ICEX 2. VCE (sat), hFE Open 3. VIN (ON) Open Open ICEX IIN IOUT IOUT Open VCE VIN (ON) VCE, VCE (sat) 5. VF 4. IR VCE 6. CIN Open IR Open VF VR IF Open Open Open fi Capacitance bridge LO Open VIN 7. tON, tOFF Input Open VOUT RL Pulse generator (Note 1) Output VIN (Note 1) tf tr Input 90% 50% 10% CL = 15 pF (Note 2) 50 s 10% tOFF tON Output VIH = 2.4 V 90% 50% 50% 0 VOH 50% VOL Note 1: Pulse Width 50 s, Duty Cycle 10% Output Impedance 50 , tr 5 ns, tf 10 ns Note 2: CL includes probe and jig capacitance 4 2011-01-14 TD62064APG/AFG IOUT - VCE (sat) IIN - VIN 1.5 TD62064APG TD62064APG Input current IIN (mA) Output current IOUT (A) 12 1.0 25C max typ. 0.5 0 0 0.5 1.0 1.5 max 4 0 1.0 2.0 2.0 Collector-emitter saturation voltage VCE (sat) (V) 3.0 Input voltage IOUT - IIN (W) (mA) 25 Power dissipation PD IOUT Output current 300 -30 200 100 0 50 100 VIN 5.0 (V) (1) DIP-16 pin on glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) (1) VCE = 2 V Ta = 75 C 4.0 PD - Ta 3.0 400 min typ. 8 150 2.4 (3) HSOP-16 pin on glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) 1.8 (2) 1.2 (4) HSOP-16 pin free air (3) (4) 0.6 0 0 200 (2) DIP-16 pin free air Input current IIN (A) 40 80 120 160 Ambient temperature Ta (C) IOUT - Duty cycle IOUT - Duty cycle 1500 1500 n=1 (mA) n=3 IOUT n=2 n=4 900 Output current Output current IOUT (mA) n=1 1200 600 300 TD62064APG 1200 n=4 n=2 600 300 TD62064APG Ta = 85C n-ch ON 20 n=3 900 Ta = 25C 0 0 200 n-ch ON 40 Duty Cycle 60 80 0 0 100 (%) 20 40 Duty Cycle 5 60 80 100 (%) 2011-01-14 TD62064APG/AFG IOUT - Duty cycle IOUT - Duty cycle 1500 1500 (mA) n=3 n=2 IOUT n=4 900 Output current Output current IOUT (mA) n=1 1200 600 300 TD62064AFG 1200 n=1 n=3 900 n=4 600 300 Ta = 25C 20 TD62064AFG Ta = 85C n-ch ON 0 0 n=2 n-ch ON 40 Duty Cycle 60 80 0 0 100 (%) 20 40 Duty Cycle 6 60 80 100 (%) 2011-01-14 TD62064APG/AFG Package Dimensions Weight: 1.11 g (typ.) 7 2011-01-14 TD62064APG/AFG Package Dimensions Weight: 0.50 g (typ.) 8 2011-01-14 TD62064APG/AFG Notes on Contents 1. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 2. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. (2) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. (3) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. (4) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. (5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. 9 2011-01-14 TD62064APG/AFG Points to Remember on Handling of ICs (1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (2) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor's power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device's motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. About solderability, following conditions were confirmed * Solderability (1) Use of Sn-37Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux 10 2011-01-14 TD62064APG/AFG RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 11 2011-01-14