AWS5518 GaAs IC SPDT Reflective Switch DC-2.0 GHz PRELIMINARY DATA SHEET - Rev 1.0 FEATURES * * * * * * High Linearity (IP3 48 dBm @ 0.9 GHz) Low Insertion Loss (0.4 dB @ 0.9 GHz) 2.7 V to 6 V Operation Low DC Power Consumption Ultra Miniature SOT-26 Package High Isolation APPLICATIONS * * * Transmit/Receive Switch Diversity Switching Antenna Selection S14 SOT-26 6 Pin Plastic Package PRODUCT DESCRIPTION The AWS5518 is a Single Pole Double Throw (SPDT) GaAs MMIC switch assembled in a SOT-26 plastic package. The AWS5518 is designed for applications that require low insertion loss, high isolation, high linearity, and small size. The switch can be controlled with positive, negative, or a combination of both voltages. Table 1: Pin Description Vs C3 RFOUT1 (J2) 1 6 2 5 3 4 V1 PIN Optional Rs see Note 3 2 GND C1 RF OUT2 (J3) 1 3 RFIN (J1) 4 V2 C2 5 Figure 1: Pinout Diagram 6 NAME DESCRIPTION RFOUT 2 (J3) RF port (can be used as an input or as an output) GND Ground connection (keep as short as possible) RFOUT 1 (J2) RF port (can be used as an input or an ouput) V1 Control voltage 1 ( Low 0 V, High 2.7 V to 5 V) RFcommon port and bias voltage for positive RFIN (J1)/Vs control (3 V to 5 V) V2 Control voltage 2 (Low 0 V, High 2.7 V to 5 V) Notes: 1. DC blocking capacitors C1,2,3 and optional resistor Rs must be supplied externally. 2. C1,2,3 = 100 pF for operation >500 MHz. 3. The use of resistor Rs to the positive voltage supply is optional. It is only required if it is necessary to independently control the RF ports, such as selecting both ports to be OFF at the same time. 03-2002 AWS5518 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT - 6 W Control Voltage -0.2 +8 V Operating Temperature -40 +85 C Storage Temperature -65 +150 C - 25 C/W RF Input Power > 900 MHz, V Control JC Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges at 25 C PARAMETER CONDITION Switching Characteritics (2) Rise, Fall (10/90% or 90/10% RF) On, Off (50% CTL to 90/10% RF) Video Feedthru Intermodulation Intercept Point (IP3) 2-tone power levels 13dBm to 27dBm MIN TYP MAX UNIT 100 100 100 nS nS mV +48 +46 +61 +56 dB m dB m dB m dB m +28 +27 +37 +37 dB m dB m dB m dB m -75 dB c (selected to optimize dynamic range of test) VCTL = 2.7 V VCTL = 5.0 V Input power for 1dB Compression FREQUENCY VCTL = 2.7 V VCTL = 5.0 V Harmonic Level Input power = +30 dBm, VCTL = 5.0 V Control Voltage (VCTL)(3) Nominal operation voltage Leakage Current VCTL = 2.7 V VCTL = 5.0 V 1.0 1.8 1.0 1.8 GHz GHz GHz GHz 1.0 1.8 1.0 1.8 GHz GHz GHz GHz +45 +42 +55 +52 1 & 1.8 GHz 2.7 6 V 50 75 A A The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: 1. All measurements made in a 50 Ohm system, unless other specified. (2) Video feedthru measured with 1 ns rise time pulse and 500 MHz bandwidth. (3) VCTL is the absolute value of the differential voltage from V1 to V2. Changing polarity selects the switch path as defined in the truth table below. Use of the optional resistor Rs on the common port limits VHIGH to Vs 0.2 V. 2 PRELIMINARY DATA SHEET - Rev 1.0 03/2002 AWS5518 Table 4: Electrical Specifications at 25 C (VCTL = 2.7 V) PARAMETER Insertion Loss FREQUENCY (2) (1) MIN DC - 1.0 GHz DC - 2.0 GHz (3) Isolation DC - 1.0 GHz DC - 2.0 GHz VSWR(3) 0.5 - 2.0 GHz 25 22 TYP MAX UNIT 0.35 0.45 0.45 0.55 dB 32 24 dB 1.4:1 dB Notes: (1) All measurements made in a 50 system, unless other specified. (2) DC = 300 kHz (3) In low insertion loss path. Table 5: Truth Table Positive Operation V1 V2 J1 - J2 J1 - J3 VHigh V Low Isolation L o w L o ss V Low VHigh L o w L o ss Isolation VHigh = 2.7 to 5 V (Vs = VHigh 0.2 V) PRELIMINARY DATA SHEET - Rev 1.0 03/2002 3 AWS5518 PERFORMANCE DATA Figure 2: Insertion Loss vs. Frequency 1.0 Figure 3: Isolation vs. Frequency 0 0.9 -5 0.8 -10 -15 0.6 Isolation (dB) Insertion Loss (dB) 0.7 0.5 0.4 0.3 -20 Input to Output Isolation -25 -30 0.2 0.1 -35 0.0 0.5 1.0 1.5 2.0 Output to Output Isolation -40 2.5 Frequency (GHz) -45 0.5 1.0 1.5 2.0 2.5 Frequency (GHz) Isolation vs Frequency Figure 4: VSWR vs. Frequency 1.4 60 TOI (dBm) 1.3 VSWR Figure 5: TOI vs. Control Voltage 65 1.2 55 50 1.0GHz 1.8GHz 1.1 45 1.0 0.5 1.0 1.5 Frequency (GHz) 4 2.0 2.5 40 2.5 3 3.5 4 Control Voltage (V) PRELIMINARY DATA SHEET - Rev 1.0 03/2002 4.5 5 AWS5518 PACKAGE OUTLINE SYMBOLS DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES MIN MAX 1.30 1.00 0.00 0.10 0.70 0.90 0.50 0.35 0.25 0.10 3.10 2.70 1.80 1.40 1.90(TYP) 3.00 2.60 0.37 9 1 MIN MAX 0.051 0.039 0.00 0.004 0.027 0.035 0.014 0.020 0.004 0.010 0.122 0.106 0.055 0.071 0.075(TYP) 0.102 0.118 0.015 9 1 A A1 A2 b C D E e H L 1 NOTE 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH AND GATE BURRS 2. DIMENSION L IS MEASURED IN GAGE PLANE 3. COPLANARITY : 0.1000 mm 4. TOLERANCE 0.1000 mm(4 mil) UNLESS OTHERWISE SPECIFIED Figure 6: S14 Package Outline Diagram PRELIMINARY DATA SHEET - Rev 1.0 03/2002 5 AWS5518 NOTES 6 PRELIMINARY DATA SHEET - Rev 1.0 03/2002 AWS5518 NOTES PRELIMINARY DATA SHEET - Rev 1.0 03/2002 7 AWS5518 ORDERING INFORMATION ORDER NUMBER PACKAGE DESCRIPTION COMPONENT PACKAGING AWS5518S14 S 14 6 Pin Plastic Package ANADIGICS, Inc. 35 Technology Drive Warren, New Jersey 07059 Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 PRELIMINARY DATA SHEET - Rev 1.0 03/2002