a FEATURES Meets EIA RS-485 Standard 5 Mbps Data Rate Single 5 V Supply -7 V to +12 V Bus Common-Mode Range High Speed, Low Power BiCMOS Thermal Shutdown Protection Short-Circuit Protection Driver Propagation Delay: 10 ns Receiver Propagation Delay: 15 ns High Z Outputs with Power Off Superior Upgrade for LTC485 APPLICATIONS Low Power RS-485 Systems DTE-DCE Interface Packet Switching Local Area Networks Data Concentration Data Multiplexers Integrated Services Digital Network (ISDN) GENERAL DESCRIPTION The ADM485 is a differential line transceiver suitable for high speed bidirectional data communication on multipoint bus transmission lines. It is designed for balanced data transmission and complies with EIA Standards RS-485 and RS-422. The part contains a differential line driver and a differential line receiver. Both the driver and the receiver may be enabled independently. When disabled, the outputs are three-stated. The ADM485 operates from a single 5 V power supply. Excessive power dissipation caused by bus contention or by output shorting is prevented by a thermal shutdown circuit. This feature forces the driver output into a high impedance state if during fault conditions a significant temperature increase is detected in the internal driver circuitry. Up to 32 transceivers may be connected simultaneously on a bus, but only one driver should be enabled at any time. It is important, therefore, that the remaining disabled drivers do not load the bus. To ensure this, the ADM485 driver features high output impedance when disabled and when powered down. 5 V Low Power EIA RS-485 Transceiver ADM485 FUNCTIONAL BLOCK DIAGRAM ADM485 RO R VCC RE B DE A DI D GND This minimizes the loading effect when the transceiver is not being used. The high impedance driver output is maintained over the entire common-mode voltage range from -7 V to +12 V. The receiver contains a fail-safe feature that results in a logic high output state if the inputs are unconnected (floating). The ADM485 is fabricated on BiCMOS, an advanced mixed technology process combining low power CMOS with fast switching bipolar technology. All inputs and outputs contain protection against ESD; all driver outputs feature high source and sink current capability. An epitaxial layer is used to guard against latch-up. The ADM485 features extremely fast switching speeds. Minimal driver propagation delays permit transmission at data rates up to 5 Mbps while low skew minimizes EMI interference. The part is fully specified over the commercial and industrial temperature range and is available in PDIP, SOIC, and small footprint MSOP packages. REV. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2003 Analog Devices, Inc. All rights reserved. ADM485-SPECIFICATIONS Parameter (VCC = 5 V 5%. All specifications TMIN to TMAX, unless otherwise noted.) Min Typ DRIVER Differential Output Voltage, VOD VOD3 |VOD| for Complementary Output States Common-Mode Output Voltage, VOC |VOD| for Complementary Output States Output Short-Circuit Current (VOUT = High) Output Short-Circuit Current (VOUT = Low) CMOS Input Logic Threshold Low, VINL CMOS Input Logic Threshold High, VINH Logic Input Current (DE, DI) RECEIVER Differential Input Threshold Voltage, VTH Input Voltage Hysteresis, VTH Input Resistance Input Current (A, B) CMOS Input Logic Threshold Low, VINL CMOS Input Logic Threshold High, VINH Logic Enable Input Current (RE) CMOS Output Voltage Low, VOL CMOS Output Voltage High, VOH Short-Circuit Output Current Three-State Output Leakage Current 2.0 1.5 1.5 35 35 Max Unit Test Conditions/Comments 5.0 5.0 5.0 5.0 0.2 3 0.2 250 250 0.8 V V V V V V V mA mA V V A R = , Test Circuit 1 VCC = 5 V, R = 50 (RS-422), Test Circuit 1 R = 27 (RS-485), Test Circuit 1 VTST = -7 V to +12 V, Test Circuit 2 R = 27 or 50 , Test Circuit 1 R = 27 or 50 , Test Circuit 1 R = 27 or 50 -7 V VO +12 V -7 V VO +12 V -7 V VCM +12 V VCM = 0 V -7 V VCM +12 V VIN = 12 V VIN = -7 V 85 1.0 V mV k mA mA V V A V V mA A 2.2 1 mA mA Digital Inputs = GND or VCC Digital Inputs = GND or VCC 2.0 1.0 -0.2 +0.2 70 12 1 -0.8 0.8 2.0 1 0.4 4.0 7 POWER SUPPLY CURRENT ICC (Outputs Enabled) ICC (Outputs Disabled) 1.0 0.6 IOUT = +4.0 mA IOUT = -4.0 mA VOUT = GND or VCC 0.4 V VOUT 2.4 V Specifications subject to change without notice. TIMING SPECIFICATIONS (VCC = 5 V 5%. All specifications TMIN to TMAX, unless otherwise noted.) Parameter DRIVER Propagation Delay Input to Output tPLH, tPHL Driver O/P to O/P, tSKEW Driver Rise/Fall Time, tR, tF Driver Enable to Output Valid Driver Disable Timing Matched Enable Switching |tAZH - tBZL|, |tBZH - tAZL| Matched Disable Switching |tAHZ - tBLZ|, |tBHZ - tALZ| RECEIVER Propagation Delay Input to Output, tPLH, tPHL Skew |tPLH - tPHL| Receiver Enable, tEN1 Receiver Disable, tEN2 Tx Pulse Width Distortion Rx Pulse Width Distortion Min Typ Max Unit Test Conditions/Comments 2 10 1 8 10 10 0 15 5 15 25 25 2 ns ns ns ns ns ns RLDIFF = 54 , CL1 = CL2 = 100 pF, Test Circuit 3 RLDIFF = 54 , CL1 = CL2 = 100 pF, Test Circuit 3 RLDIFF = 54 , CL1 = CL2 = 100 pF, Test Circuit 3 RL = 110 , CL = 50 pF, Test Circuit 4 RL = 110 , CL = 50 pF, Test Circuit 4 RL = 110 , CL = 50 pF, Test Circuit 4* 0 2 ns RL = 110 , CL = 50 pF, Test Circuit 4* 15 30 5 20 20 ns ns ns ns ns ns CL = 15 pF, Test Circuit 5 CL = 15 pF, Test Circuit 5 CL = 15 pF, RL = 1 k, Test Circuit 6 CL = 15 pF, RL = 1 k, Test Circuit 6 8 5 5 1 1 *Guaranteed by characterization. Specifications subject to change without notice. -2- REV. E ADM485 ABSOLUTE MAXIMUM RATINGS* Table I. Transmitting (TA = 25C, unless otherwise noted.) Inputs VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V Inputs Driver Input (DI) . . . . . . . . . . . . . . . . -0.3 V to VCC + 0.3 V Control Inputs (DE, RE) . . . . . . . . . . -0.3 V to VCC + 0.3 V Receiver Inputs (A, B) . . . . . . . . . . . . . . . . . . -9 V to +14 V Outputs Driver Outputs (A, B) . . . . . . . . . . . . . . . . . . -9 V to +14 V Receiver Output . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V Power Dissipation 8-Lead MSOP . . . . . . . . . . . . . . . . 900 mW JA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 206C/W Power Dissipation 8-Lead PDIP . . . . . . . . . . . . . . . . . 500 mW JA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 130C/W Power Dissipation 8-Lead SOIC . . . . . . . . . . . . . . . . . 450 mW JA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 170C/W Operating Temperature Range Commercial (J Version) . . . . . . . . . . . . . . . . . . . 0C to 70C Industrial (A Version) . . . . . . . . . . . . . . . . . -40C to +85C Storage Temperature Range . . . . . . . . . . . . -65C to +150C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . 300C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215C Infrared (15 sec). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220C Outputs DE DI B A 1 1 0 1 0 X 0 1 Z 1 0 Z Table II. Receiving RE 0 0 0 1 Inputs A-B Output RO +0.2 V -0.2 V 1 0 1 Z Inputs Open X *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended periods of time may affect device reliability. ORDERING GUIDE Model Temperature Range Package Option ADM485AN ADM485AR ADM485AR-REEL ADM485ARZ* ADM485ARZ-REEL* ADM485ARM ADM485ARM-REEL ADM485ARM-REEL7 ADM485JN ADM485JR ADM485JR-REEL ADM485JR-REEL7 ADM485JRZ* ADM485JRZ-REEL* ADM485JRZ-REEL7* -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C N-8 R-8 R-8 R-8 R-8 RM-8 RM-8 RM-8 N-8 R-8 R-8 R-8 R-8 R-8 R-8 Branding M41 M41 M41 *Z = Lead Free. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADM485 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. E -3- ADM485 PIN CONFIGURATION RO 1 RE 8 ADM485 VCC B TOP VIEW DE 3 (Not to Scale) 6 A 2 DI 4 7 5 GND PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1 RO 2 RE 3 DE 4 DI 5 6 7 8 GND A B VCC Receiver Output. When enabled, if A > B by 200 mV, then RO = High. If A < B by 200 mV, then RO = Low. Receiver Output Enable. A low level enables the receiver output, RO. A high level places it in a high impedance state. Driver Output Enable. A high level enables the driver differential outputs, A and B. A low level places it in a high impedance state. Driver Input. When the driver is enabled, a Logic Low on DI forces A low and B high while a Logic High on DI forces A high and B low. Ground Connection, 0 V. Noninverting Receiver Input A/Driver Output A. Inverting Receiver Input B/Driver Output B. Power Supply, 5 V 5%. -4- REV. E ADM485 Test Circuits VCC A R RL S1 0V OR 3V VOD S2 DE R CL B VOC VOUT DE IN Test Circuit 1. Driver Voltage Measurement Test Circuit 4. Driver Enable/Disable 375 A VOD3 VTST 60 VOUT RE B CL 375 Test Circuit 5. Receiver Propagation Delay Test Circuit 2. Driver Voltage Measurement VCC +1.5V A CL1 S1 RLDIFF RL S2 -1.5V RE CL CL2 B VOUT RE IN Test Circuit 3. Driver Propagation Delay Test Circuit 6. Receiver Enable/Disable Switching Characteristics 3V 1.5V 0V 1.5V tPLH tPHL A, B B 0V 0V tPLH tPHL 1/2VO VO A tSKEW = tPLH - tPHL VO VOH 90% POINT 90% POINT RO 0V -VO 10% POINT 1.5V 10% POINT tR tSKEW = tPLH - tPHL VOL tF Figure 1. Driver Propagation Delay, Rise/Fall Timing Figure 3. Receiver Propagation Delay 3V 3V DE 1.5V 1.5V RE 1.5V 1.5V 0V 0V tZL tLZ tZL 2.3V A, B VOL + 0.5V tZH tHZ tLZ 1.5V R VOL VOL + 0.5V O/P LOW tZH VOH A, B 1.5V VOL tHZ O/P HIGH VOH - 0.5V 2.3V R 0V 1.5V VOH VOH - 0.5V 0V Figure 2. Driver Enable/Disable Timing REV. E Figure 4. Receiver Enable/Disable Timing -5- ADM485-Typical Performance Characteristics 0.40 50 I = 8mA 45 0.35 OUTPUT VOLTAGE - V OUTPUT CURRENT - mA 40 35 30 25 20 15 10 0.30 0.25 0.20 5 0 0 0.25 0.50 0.75 1.00 1.25 1.50 OUTPUT VOLTAGE - V 1.75 0.15 -50 2.00 0 90 -2 80 -4 70 -6 -8 -10 -12 25 50 TEMPERATURE - C 75 100 125 60 50 40 30 -14 20 -16 10 -18 3.50 0 TPC 4. Receiver Output Low Voltage vs. Temperature OUTPUT CURRENT - mA OUTPUT CURRENT - mA TPC 1. Output Current vs. Receiver Output Low Voltage -25 0 3.75 4.00 4.25 4.50 4.75 0 5.00 0.5 1.0 1.5 2.0 2.5 3.0 OUTPUT VOLTAGE - V OUTPUT VOLTAGE - V 3.5 4.0 4.5 TPC 5. Output Current vs. Driver Differential Output Voltage TPC 2. Output Current vs. Receiver Output High Voltage 2.15 4.55 I = 8mA DIFFERENTIAL VOLTAGE - V OUTPUT VOLTAGE - V 4.50 4.45 4.40 4.35 4.30 4.25 2.10 2.05 2.00 1.95 4.20 4.15 -50 -25 0 25 50 75 TEMPERATURE - C 100 1.90 -50 125 TPC 3. Receiver Output High Voltage vs. Temperature -25 0 25 50 75 TEMPERATURE - C 100 125 TPC 6. Driver Differential Output Voltage vs. Temperature, RL = 26.8 -6- REV. E ADM485 0.7 100 90 0.6 OUTPUT CURRENT - mA 80 0.5 70 | tPLH - tPHL | TIME - ns 60 50 40 30 0.4 0.3 0.2 20 0.1 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 OUTPUT VOLTAGE - V 3.5 4.0 0 -50 4.5 -25 0 25 50 75 TEMPERATURE - C 100 125 TPC 10. Rx Skew vs. Temperature TPC 7. Output Current vs. Driver Output Low Voltage 6 0 -10 5 -30 4 -40 TIME - ns OUTPUT CURRENT - mA -20 -50 -60 -70 3 | tPHLA - tPHLB | 2 -80 -90 1 -100 | tPLHA - tPLHB | -110 -120 0 0.5 1.0 2.0 3.0 1.5 2.5 3.5 OUTPUT VOLTAGE - V 4.0 4.5 0 -50 5.0 0 25 50 75 TEMPERATURE - C 100 125 TPC 11. Tx Skew vs. Temperature TPC 8. Output Current vs. Driver Output High Voltage 1.4 1.1 1.2 1.0 DRIVER ENABLED 1.0 0.9 0.8 PWD SUPPLY CURRENT - mA -25 0.8 | tPLH - tPHL | 0.6 0.7 0.4 DRIVER DISABLED 0.6 0.2 0.5 -50 -25 0 25 50 TEMPERATURE - C 75 100 0 -50 125 0 25 50 75 TEMPERATURE - C 100 125 TPC 12. Tx Pulse Width Distortion TPC 9. Supply Current vs. Temperature REV. E -25 -7- 150 ADM485 A DI 4 A B B 1, 2 1, 2 RO 3 TPC 13. Unloaded Driver Differential Outputs TPC 16. Driver/Receiver Propagation Delays High to Low A A B B 1, 2 1, 2 TPC 14. Loaded Driver Differential Outputs TPC 17. Driver Output at 30 Mbps DI 4 A B 1, 2 RO 3 TPC 15. Driver/Receiver Propagation Delays Low to High -8- REV. E ADM485 APPLICATION INFORMATION Differential Data Transmission on the bus. Only one driver can transmit at a particular time, but multiple receivers may be enabled simultaneously. Differential data transmission is used to reliably transmit data at high rates over long distances and through noisy environments. Differential transmission nullifies the effects of ground shifts and noise signals that appear as common-mode voltages on the line. There are two main standards approved by the Electronics Industries Association (EIA) that specify the electrical characteristics of transceivers used in differential data transmission. As with any transmission line, it is important that reflections be minimized. This can be achieved by terminating the extreme ends of the line using resistors equal to the characteristic impedance of the line. Stub lengths of the main line should also be kept as short as possible. A properly terminated transmission line appears purely resistive to the driver. RT The RS-422 standard specifies data rates up to 10 MBaud and line lengths up to 4000 ft. A single driver can drive a transmission line with up to 10 receivers. RT D In order to cater for true multipoint communications, the RS-485 standard was defined. This standard meets or exceeds all the requirements of RS-422 but also allows for up to 32 drivers and 32 receivers to be connected to a single bus. An extended common-mode range of -7 V to +12 V is defined. The most significant difference between RS-422 and RS-485 is the fact that the drivers may be disabled, thereby allowing more than one (32 in fact) to be connected to a single line. Only one driver should be enabled at a time, but the RS-485 standard contains additional specifications to guarantee device safety in the event of line contention. D R R R D R D Figure 5. Typical RS-485 Network Thermal Shutdown Table III. Comparison of RS-422 and RS-485 Interface Standards Specification RS-422 RS-485 Transmission Type Maximum Cable Length Minimum Driver Output Voltage Driver Load Impedance Receiver Input Resistance Receiver Input Sensitivity Receiver Input Voltage Range No. of Drivers/Receivers per Line Differential 4000 ft. 2 V 100 4 k min 200 mV -7 V to +7 V 1/10 Differential 4000 ft. 1.5 V 54 12 k min 200 mV -7 V to +12 V 32/32 The ADM485 contains thermal shutdown circuitry that protects the part from excessive power dissipation during fault conditions. Shorting the driver outputs to a low impedance source can result in high driver currents. The thermal sensing circuitry detects the increase in die temperature and disables the driver outputs. The thermal sensing circuitry is designed to disable the driver outputs when a die temperature of 150C is reached. As the device cools, the drivers are re-enabled at 140C. Propagation Delay The ADM485 features very low propagation delay, ensuring maximum baud rate operation. The driver is well balanced, ensuring distortion free transmission. Cable and Data Rate The transmission line of choice for RS-485 communications is a twisted pair. Twisted pair cable tends to cancel commonmode noise and causes cancellation of the magnetic fields generated by the current flowing through each wire, thereby reducing the effective inductance of the pair. Another important specification is a measure of the skew between the complementary outputs. Excessive skew impairs the noise immunity of the system and increases the amount of electromagnetic interference (EMI). The ADM485 is designed for bidirectional data communications on multipoint transmission lines. A typical application showing a multipoint transmission network is illustrated in Figure 5. An RS-485 transmission line can have as many as 32 transceivers The receiver input includes a fail-safe feature that guarantees a Logic High on the receiver when the inputs are open circuit or floating. REV. E Receiver Open-Circuit Fail-Safe -9- ADM485 OUTLINE DIMENSIONS 8-Lead Standard Small Outline Package [SOIC] (R-8) Dimensions shown in millimeters and (inches) 5.00 (0.1968) 4.80 (0.1890) 4.00 (0.1574) 3.80 (0.1497) 8 5 1 4 6.20 (0.2440) 5.80 (0.2284) 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 0.51 (0.0201) 0.31 (0.0122) COPLANARITY SEATING 0.10 PLANE 0.50 (0.0196) 45 0.25 (0.0099) 1.75 (0.0688) 1.35 (0.0532) 8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 3.00 BSC 8 5 4.90 BSC 3.00 BSC 1 4 PIN 1 0.65 BSC 1.10 MAX 0.15 0.00 0.38 0.22 COPLANARITY 0.10 0.23 0.08 8 0 0.80 0.40 SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-187AA -10- REV. E ADM485 OUTLINE DIMENSIONS 8-Lead Plastic Dual In-Line Package [PDIP] (N-8) Dimensions shown in inches and (millimeters) 0.375 (9.53) 0.365 (9.27) 0.355 (9.02) 8 5 1 4 0.295 (7.49) 0.285 (7.24) 0.275 (6.98) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.100 (2.54) BSC 0.180 (4.57) MAX 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.015 (0.38) MIN SEATING PLANE 0.060 (1.52) 0.050 (1.27) 0.045 (1.14) 0.150 (3.81) 0.135 (3.43) 0.120 (3.05) 0.015 (0.38) 0.010 (0.25) 0.008 (0.20) COMPLIANT TO JEDEC STANDARDS MO-095AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN REV. E -11- ADM485 Revision History Location Page 10/03--Data Sheet changed from REV. D to REV. E. Updated ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7/03--Data Sheet changed from REV. C to REV. D. Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Update to OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1/03--Data Sheet changed from REV. B to REV. C. Change to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Change to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 12/02--Data Sheet changed from REV. A to REV. B. Deleted Q-8 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits, additions to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Edits, additions to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Additions to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TPCs updated and reformatted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Addition of 8-Lead MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Update to OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 -12- REV. E C00078-0-10/03(E) Changes to TIMING SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2