06-Serie_IB-IS-A_06-Serie IB-IS-A 21/11/12 14:26 Page25 IB and IS series Sealed pushbutton switches - bushing O 12 mm - momentary Distinctive features and specifications Snap-in and threaded bushing models Compact, light in weight * Behind-panel depth of 13 mm (.512) only * 50 % reduction in weight compared to metallic models Tactile feedback Sealed to IP67 (IS series) or IP54 (IB series) B1 ENVIRONMENTAL SPECIFICATIONS MATERIALS * Front panel sealing according to IEC 60529 : IP67 (IS) or IP54 (IB) * Shock resistance : 100 g according to IEC 512-4, test 6c * Vibration resistance : 10-500 Hz - 10 g according to IEC 512-4, test 6d * Salt spray : IEC 512-6, test 11f * Operating temperature : -40C to +85C ELECTRICAL SPECIFICATIONS * Case : thermoplastic UL94-V0 * Actuator : polyamide 6/6 * Bushing/bezel : polyamide 6/6 * Contacts : silver, gold plated * Terminal seal : epoxy AGENCY APPROVAL * Max. current/voltage rating with resistive load : 400mA 32VAC - 100mA 48VDC * Initial contact resistance : 50 m max. * Insulation resistance : 1 G min. at 500VDC * Dielectric strength : 1.000 Vrms * Electrical life at full load : 500.000 cycles 2A 125VAC/250VAC File E83438 Availability : consult factory for details of approved models. Marking : to order switches marked UL, complete approrpiate box of ordering format. GENERAL SPECIFICATIONS * Panel thickness : - IB series : 0,8 mm (.031) min. - 1,8 mm ( .071) max. - IS series : 1,5 mm (.059) min. - 4 mm (.157) max. * Total travel : 1,7 mm (.066) +/- 0,3 mm * Typical operating force : 4N +/- 3N * Low level or mechanical life : 1.000.000 cycles * Torque : 1,5 Nm max. applied to nut * Soldering : 300C max. for 3 seconds itch: m sw s. o t s u f c e serie ple o h Exame end of t se Panel mounting : see next pages. APEM www.apem.com B1-25 06-Serie_IB-IS-A_06-Serie IB-IS-A 21/11/12 14:26 Page26 IB and IS series Sealed pushbutton switches - bushing O 12 mm - momentary Overview SERIES IB Snap-in IS Threaded bushing Actuator shapes R P Round, curved Round, flat 3 Electrical function Terminals Normally open (NO) S Solder lug Z1 Quick-connect 2,8 x 0,5 mm P Straight PC Contacts AD Silver, gold plated B1 Actuator colours 1 B 2 3 5 6 7/1 8 9 A Blue Dark blue Black Green Yellow Red White Bright chrome Orange Satin chrome Bezel finish 00 08 10 20 Black (std) Bright chrome (IS only) White Satin chrome (IS only) Option 104 High actuator Approval UL Consult factory for detail of approved models. ABOUT THIS SERIES On the following pages, you will find successively : - model structure of switches and options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketed numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand. It is presented after the IA series and in section H. Mounting accessories : Standard hardware supplied : 1 flat seal (IB series) 1 hex nut 14 mm (.551) across flats and 1 flat seal (IS series). Hex nut part number U166. Packaging unit : 50 pieces B1-26 www.apem.com APEM 06-Serie_IB-IS-A_06-Serie IB-IS-A 21/11/12 14:26 Page27 IB and IS series Sealed pushbutton switches - bushing O 12 mm - momentary * Ten actuator colours * Curved or flat actuator * Antirotation bushing Solder lug S Quick-connect Z1 3.40 (.133) 1.00 (.039) 1.50 (.059) 1.20 (.047) 8.40 (.330) 2.40 (.094) Straight P 1.20 (.047) 2.80 (.110) 2.80 (.110) MODEL STRUCTURE Actuator marking available on IBP and ISP models (symbol 10 mm max.). On request. Snap-in mounting - solder lug terminals Panel thickness : 0,8 mm to 1,8 mm Flat O17.50 (.688DIA) Normally open 1.20 (.047) Flat actuator IBP3SAD 5.00 (.196) Normally open 3.20 (.125) 13.00 (.511) Curved actuator IBR3SAD 2.00 (.078) O12.00 (.472DIA) 0.50 (.019) 2.80 (.110) EPOXY 5.08 (.200) Also available with straight PC : IB*3PAD or quick-connect terminals : IB*3Z1AD Flat Mounting by threaded bushing - solder lug terminals Panel thickness : 1,5 mm to 4 mm O17.50 (.688DIA) 5.60 (.220) Normally open 1.20 (.047) Flat actuator ISP3SAD 5.00 (.196) Normally open 13.00 (.511) Curved actuator ISR3SAD 2.00 (.078) O12.00 (.472DIA) 3.20 (.125) 0.50 (.019) 2.80 (.110) 5.08 (.200) EPOXY O12.00x0.75SI (.472DIAx0.75IS) Also available with straight PC : IS*3PAD or quick-connect terminals : IS*3Z1AD ACTUATOR COLOURS Actuator marking available on IBP and ISP models (symbol 10 mm max.). On request. 1 : blue - B : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome 9 : orange - A : satin chrome BUSHING AND BEZEL FINISH 00 : Black (standard) 08 : Bright chrome (IS series only) 10 : White 20 : Satin chrome (IS series only) APEM www.apem.com B1-27 B1 06-Serie_IB-IS-A_06-Serie IB-IS-A 21/11/12 14:26 Page28 IB and IS series O12.00 (.472DIA) O12.00 (.472DIA) 4.70 (.185) ACTUATOR OPTION 4.70 (.185) Sealed pushbutton switches - bushing O 12 mm - momentary 104 : High actuator IBR IBP APPROVAL UL Availability : consult factory for details of approved models. Marking : to order switches marked UL, complete above box with "UL". IB SERIES MOUNTING 18.00 (.709) 18.00 (.709) 18.00 (.709) 12.90 (.507) Matrix mounting 1.80 MAXI. (.071MAX.) Panel cut-out 0.80 MINI. (.031MIN.) O13.60 (.535DIA) IS SERIES MOUNTING Matrix mounting 12.90 (.507) 1 20.00 (.787) 20.00 (.787) 20.00 (.787) Panel cut-out 1.50min-4Max (.059MIN.-.157MAX.) B1 O13.60 (.535DIA) Flat seal O13.50 (.531DIA) Example of custom switch * Painted bushing and actuator, soft feel * Flying leads (55 mm) + connector * Overmolded rear part ISR3FADB22X1248-01 B1-28 www.apem.com APEM