3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M MetPak HSHM Press-Fit Header
2 mm Type A, 110 Signal Contacts, 5 Rows, Straight HSHM Series
Up to 5 Gb/s data rates
Low crosstalk at high frequencies
50/100 Ω (single-ended /differential) impedance
Modular/scalable format IEC 61076-4-101
63 mated lines per linear inch
Multi-purpose center (MPC) for keying and guidance
End-to-end stackable with 5 row 3M MetPak CP2,
HM and HSHM sockets
See the Regulatory Information Appendix (RIA) in
the “RoHS compliance” section of
www.3mconnector.com for compliance information
Date Modifi ed: November 9, 2010 TS-2073-B
Sheet 1 of 3
Physical
Insulation Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact
Material: Copper Alloy
Plating: See Ordering Information
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield
Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield
Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield
Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield
Mate/Unmate Cycles: 250
Application: This module is suitable for stand-alone use. (Refer to IEC-61076-4-101)
Electrical:
Data Rate: 5 Gb/s
Characteristic Impedance: 50 Ω Single-ended, 100 Ω Differential
Current Rating (Fully Loaded): 1 A @ 70°C Signal
Insulation Resistance: 104 MΩ @ 100 VDC
Withstanding Voltage: 750 Vrms
Environmental
Temperature Rating: -55° C to 125° C
UL File No.: E68080 MetPak is a trademark of 3M Company.
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M MetPak HSHM Press-Fit Header
2 mm Type A, 110 Signal Contacts, 5 Rows, Straight HSHM Series
TS-2073-B
Sheet 2 of 3
Ordering Information
HSHM-H110AX - 5CPX- XXXXX
mm
(Inch)
Tolerance Unless Noted
0 0.0 0.00
mm ±3 ±0.3 ±0.13
[ ] Dimensions for
Reference Only
High Speed Option:
4 =Coaxial, column differential and stripline
(75 Ω) applications
5 =Row differential applications
d e n o t e s s h ie ld c o lu m n ( t a il o n ly ) o m it t e d f o r t h e r o w
d if f e r e n t ia l p a ir p a r t
R O W F
R O W E
R O W D
R O W C
R O W B
R O W A
R O W Z
P in p o s it io n s
S h ie ld p o s it i o n s
49.85
1.963
1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4
1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5
HSHM -HXXXXX-5XPX-XXXXX
R E V X X X Y Y
HSHM -HXXXXX-5XPX-XXXXX
R E V X X X Y Y
15.15
. 5 9 6
R o w d if f e r e n t ia l c o n f ig u r a t io n
s h o w n w it h p r o t e c t iv e c a p s *
* C a p s t o b e r e m o v e d a f t e r p r e s s - f it in s t a lla t io n p r o c e s s
D I M B
D IM A 4 . 5 0
. 1 7 7
D IM C
1 .5 0
.0 5 9
4 .5 0
. 1 7 7
5 .0 0
.1 9 7
9 .6 0
.3 7 8
1 5 .4 0
. 6 0 6
1 3 . 4 0
.5 2 8
S i g n a l
c o n t a c t s
In t e r s tit ia l
g r o u n d
c o n ta c ts
D I M A = P i n m a t in g le n g t h
D I M B = S h ie ld t a il le n g t h
D I M C = P in t a il le n g th
C o a x ia l, c o l u m n d iff e r e n t ia l a n d s t r ip lin e c o n f ig u r a ti o n
s h o w n w it h p r o t e c t iv e c a p s *
48.00
1.890
1 2 . 0 0
.4 7 2
2 . 0 0
.0 7 9
2 .0 0
.0 7 9
2 . 0 0
.0 7 9
2 . 0 0
.0 7 9
Plating μm [ μ” ]:
TG30 = 0.76 [30] Min. Au Contact Area
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Standard Option
TG30L = 0.76 [30] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
TG50 = 1.27 [50] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
Standard Configuration
DIM A = 5.3 mm for rows A through E
For non-standard configurations,
contact sales representative
(rows F and Z not loaded)
Tail Length:
1 =4.4 mm pin and 3.5 mm shield
2 =2 mm pin and 2 mm shield
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M MetPak HSHM Press-Fit Header
2 mm Type A, 110 Signal Contacts, 5 Rows, Straight HSHM Series
TS-2073-B
Sheet 3 of 3
Hole Plating Table mm [in.]
Finsihed Hole Dia. “D” Cu. Thickness SnPb Thickness Drilled Hole Dia.
0.457 - 0.559 [.0180 - .0220] 0.025 - 0.045 [.0010 - .0018] 0.008 -0.018 [.0003 - .0007] 0.584 - 0.625 [.0230 - .0246]
Recommended PCB hole mounting pattern for coaxial,
column differential and stripline applications
Recommended PCB hole mounting pattern for row differential
applications
(Same geometry as left view without the ground vias)
Plated thru holes
DIM D
0.10 A B
2.00
1.00
2.00
1.00
4.00
4.00
2.00
+0.05
0
Unplated thru hole
48.00
8.00
ABCDE A
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ABCDE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
0.10 A B
Ø
Ø
Ø
Ø
M
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2010. All rights reserved.
RIA-2217B-E
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3Mconnector.com 3M is a trademark of 3M Company.