LM25115A LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking Literature Number: SNVS501A LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking General Description Features The LM25115A controller contains all of the features necessary to produce multiple tracking outputs using the Secondary Side Post Regulation (SSPR) technique. The SSPR technique develops a highly efficient and well regulated auxiliary output from the secondary side switching waveform of an isolated power converter. LM25115A can be also used as a standalone DC/DC synchronous buck controller (Refer to Synchronous Buck section). Regulation of the auxiliary output voltage is achieved by leading edge pulse width modulation (PWM) of the main channel duty cycle. Leading edge modulation is compatible with either current mode or voltage mode control of the main output. The LM25115A drives external high-side and low-side NMOS power switches configured as a synchronous buck regulator. A current sense amplifier provides overload protection and operates over a wide common mode input range. Additional features include a low dropout (LDO) bias regulator, error amplifier, precision reference, adaptive dead time control of the gate signals and thermal shutdown. Power-up/Power-down Tracking Self-synchronization to main channel output Leading edge pulse width modulation Valley current Mode control Standalone DC/DC synchronous buck mode Operates from AC or DC input up to 42V Wide 4.5V to 30V bias supply range Wide 0.75V to 13.5V output range. Top and bottom gate drivers sink 2.5A peak Adaptive gate driver dead-time control Wide bandwidth error amplifier (4MHz) Programmable soft-start Thermal shutdown protection TSSOP-16 package Typical Application Circuit 30008301 FIGURE 1. Simplified Multiple Output Power Converter Utilizing SSPR Technique (c) 2007 National Semiconductor Corporation 300083 www.national.com LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking February 2007 LM25115A Connection Diagram 30008302 16-Lead TSSOP See NS Package Numbers MTC16 Ordering Information Package Type Nsc Package Drawing Supplied As LM25115AMT Ordering Number TSSOP-16 MTC16 92 Units Per Anti-Static Tube LM25115AMTX TSSOP-16 MTC16 2500 units shipped as Tape & Reel Pin Descriptions Pin Name 1 CS Current Sense amplifier positive input A low inductance current sense resistor is connected between CS and VOUT. Current limiting occurs when the differential voltage between CS and VOUT exceeds 45mV (typical). 2 VOUT Current sense amplifier negative input Connected directly to the output voltage. The current sense amplifier operates over a voltage range from 0V to 13.5V at the VOUT pin. 3 AGND Analog ground Connect directly to the power ground pin (PGND). 4 CO Current limit output For normal current limit operation, connect the CO pin to the COMP pin through a diode. CO pin is connected to ground through a resistor in series with a capacitor to provide adequate control loop compensation for the current limit gm amplifier. Leave this pin open to disable the current limit function. 5 COMP Compensation. Error amplifier output COMP pin pull-up is provided by an internal 300uA current source. 6 FB Feedback. Error amplifier inverting input Connected to the regulated output through the feedback resistor divider and compensation components. The non-inverting input of the error amplifier is internally connected to the SS pin. 7 TRK/SS Tracking/Soft-start control Non-inverting input to error amp with 15 A pull-up current source. Can be used with capacitor for soft-start or tied to external divider of a master output for tracking. TRK/SS is the reference input to the amplifier when the voltage applied to the pin is < 0.75V. For higher inputs, the internal reference controls the amplifier. 8 RAMP PWM Ramp signal An external capacitor connected to this pin sets the ramp slope for the voltage mode PWM. The RAMP capacitor is charged with a current that is proportional to current into the SYNC pin. The capacitor is discharged at the end of every cycle by an internal MOSFET. www.national.com Description Application Information 2 Name Description Application Information 9 SYNC Synchronization input A low impedance current input pin. The current into this pin sets the RAMP capacitor charge current and the frequency of an internal oscillator that provides a clock for the free-run (DC input) mode . 10 PGND Power Ground Connect directly to the analog ground pin (AGND). 11 LO Low-side gate driver output Connect to the gate of the low-side synchronous MOSFET through a short low inductance path. 12 VCC Output of bias regulator Nominal 7V output from the internal LDO bias regulator. Locally decouple to PGND using a low ESR/ESL capacitor located as close to controller as possible. 13 HS High-side MOSFET source connection Connect to negative terminal of the bootstrap capacitor and the source terminal of the high-side MOSFET. 14 HO High-side gate driver output Connect to the gate of high-side MOSFET through a short low inductance path. 15 HB High-side gate driver bootstrap rail Connect to the cathode of the bootstrap diode and the positive terminal of the bootstrap capacitor. The bootstrap capacitor supplies current to charge the high-side MOSFET gate and should be placed as close to controller as possible. 16 VBIAS Supply Bias Input Input to the LDO bias regulator and current sense amplifier that powers internal blocks. Input range of VBIAS is 4.5V to 30V. 3 www.national.com LM25115A Pin LM25115A Junction Temperature ESD Rating HBM (Note 2) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VBIAS to GND VCC to GND HS to GND VOUT, CS to GND All other inputs to GND Storage Temperature Range +150C 2 kV Operating Ratings -0.3V to 32V -0.3V to 9V -1V to 45V - 0.3V to 15V -0.3V to 7.0V -55C to +150C VBIAS supply voltage VCC supply voltage HS voltage HB voltage Operating Junction Temperature 5V to 30V 5V to 7.5V 0V to 42V VCC + HS -40C to +125C Typical Operating Conditions Max Units Supply Voltage, VBIAS Parameter Min 4.5 30 V Supply Voltage, VCC 4.5 7 V Supply voltage bypass, CVBIAS 0.1 1 Reference bypass capacitor, CVCC 0.1 1 HB-HS bootstrap capacitor Typ F 10 F 0.047 F SYNC Current Range (VCC = 4.5V) 50 150 A RAMP Saw Tooth Amplitude 1 1.75 V 0.75 13.5 V VOUT regulation voltage (VBIAS min = 3V + VOUT) Electrical Characteristics (Note 3) Unless otherwise specified, TJ = -40C to +125C, VBIAS = 12V, No Load on LO or HO. Symbol Parameter Conditions Min Typ Max Units 4 mA VBIAS SUPPLY Ibias VBIAS Supply Current FSYNC = 200kHz VCC LOW DROPOUT BIAS REGULATOR VccReg VCC Regulation VCC open circuit. Outputs not switching VCC Current Limit (Note 4) 6.65 7 7.15 40 VCC Under-voltage Lockout Voltage Positive going VCC VCC Under-voltage Hysteresis 4 V mA 4.5 V 0.2 0.25 0.3 V 10 15 20 A TRACK / SOFT-START SS Pull-up Source SS Discharge Impedance 140 ERROR AMPLIFIER and FEEDBACK REFERENCE VREF GBW Vio FB Reference Voltage Measured at FB pin FB Input Bias Current FB = 2V .737 .750 .763 V 0.2 0.5 A COMP Source Current 300 Open Loop Voltage Gain 60 dB Gain Bandwidth Product 4 MHz Input Offset Voltage A 22 mV COMP Offset Threshold for VHO = high RAMP = CS = VOUT = 0V 2 V RAMP Offset Threshold for VHO = high COMP = 1.5V, CS = VOUT = 0V 1.0 V CURRENT SENSE AMPLIFIER Current Sense Amplifier Headroom Headroom = Vbias - Vout Vbias= 4.5 V and Vout= 1.5 V Current Sense Amplifier Gain www.national.com V 3 16 V/V Output DC Offset 1.27 V Amplifier Bandwidth 500 kHz 4 Parameter Conditions Min Typ Max Units CURRENT LIMIT Slow ILIMIT Amp Transconductance 5 mA / V Overall Transconductance 90 mA / V Slow ILimit Threshold VCL = VCS - VVOUT VOUT = 6V and CO/COMP = 1.5V 39 45 51 mV Slow ILimit Foldback VCL = VCS - VVOUT VOUT = 0V and CO/COMP = 1.5V 34 39 46 mV Fast ILimit Pull-Down Current Vds = 2V 45 mA 60 mV VOUT = 6V VCL = VCS - VVOUT to cause LO to shutoff -17 mV Fast ILimit Threshold VCLNEG Negative Current Limit CO Clamp Voltage 5.5 ICO Pull-Up Current 6 6.5 V 15 A 2.5 k RAMP GENERATOR SYNC Input Impedance SYNC Threshold End of cycle detection threshold Free Run Mode Peak Threshold RAMP peak voltage with dc current applied to SYNC. Current Mirror Gain Ratio of RAMP charge current to SYNC input current. Discharge Impedance 20 2.7 A 2.35 V 3.3 A/A 100 LOW-SIDE GATE DRIVER VOLL LO Low-state Output Voltage ILO = 100mA 0.15 0.5 V VOHL LO High-state Output Voltage ILO = -100mA, VOHL = VCC -VLO 0.35 0.8 LO Rise Time CLOAD = 1000pF 15 ns V LO Fall Time CLOAD = 1000pF 12 ns IOHL Peak LO Source Current VLO = 0V 2 A IOLL Peak LO Sink Current VLO = 12V 2.5 A HIGH-SIDE GATE DRIVER VOLH HO Low-state Output Voltage IHO = 100mA 0.15 0.5 V VOHH HO High-state Output Voltage IHO = -100mA, VOHH = VHB -VHO 0.35 0.8 HO Rise Time CLOAD = 1000pF 15 ns V HO High-side Fall Time CLOAD = 1000pF 12 ns IOHH Peak HO Source Current VHO = 0V 2 A IOLH Peak HO Sink Current VHO = 12V 2.5 A LO Fall to HO Rise Delay CLOAD = 0 40 ns HO Fall to LO Rise Delay CLOAD = 0 50 ns SYNC Fall to HO Fall Delay CLOAD = 0 120 ns SYNC Rise to LO Fall Delay CLOAD = 0 80 ns SWITCHING CHARACTERISITCS 5 www.national.com LM25115A Symbol LM25115A Symbol Parameter Conditions Min Typ Max Units 150 165 C 25 C THERMAL SHUTDOWN TSD Thermal Shutdown Temp. Thermal Shutdown Hysteresis THERMAL RESISTANCE JA Junction to Ambient MTC Package 125 C/W JA Junction to Ambient SDA Package 32 C/W Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. Note 3: Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 4: Device thermal limitations may limit usable range. www.national.com 6 Efficiency vs. Load Current and Vphase (VOUT = 2.5V) VCC Regulator Start-up Characteristics, VCC vs. VBIAS 30008322 30008304 Current Value (CV) vs. Current Limit (VCL) Current Sense Amplifier Gain and Phase vs. Frequency 30008307 30008306 Current Error Amplifier Transconductance Overall Current Amplifier Transconductance 30008309 30008308 7 www.national.com LM25115A Typical Performance Characteristics LM25115A Common Mode Output Voltage vs. Positive Current Limit Common Mode Output Voltage vs. Negative Current Limit (Room Temp) 30008310 30008311 VCC Load Regulation to Current Limit 30008305 www.national.com 8 LM25115A Block Diagram 30008303 9 www.national.com LM25115A Detailed Operating Description Synchronization (SYNC) and FeedForward (RAMP) The LM25115A controller contains all of the features necessary to implement multiple output power converters utilizing the Secondary Side Post Regulation (SSPR) technique. The SSPR technique develops a highly efficient and well regulated auxiliary output from the secondary side switching waveform of an isolated power converter. Regulation of the auxiliary output voltage is achieved by leading edge pulse width modulation (PWM) of the main channel duty cycle. Leading edge modulation is compatible with either current mode or voltage mode control of the main output. The LM25115A drives external high-side and low-side NMOS power switches configured as a synchronous buck regulator. A current sense amplifier provides overload protection and operates over a wide common mode input range from 0V to 13.5V. Additional features include a low dropout (LDO) bias regulator, error amplifier, precision reference, adaptive dead time control of the gate driver signals and thermal shutdown. The pulsing "phase signal" from the main converter synchronizes the PWM ramp and gate drive outputs of the LM25115A. The phase signal is the square wave output from the transformer secondary winding before rectification (Figure 1). A resistor connected from the phase signal to the low impedance SYNC pin produces a square wave current (ISYNC) as shown in Figure 2. A current comparator at the SYNC input monitors ISYNC relative to an internal 15A reference. When ISYNC exceeds 15A, the internal clock signal (CLK) is reset and the capacitor connected to the RAMP begins to charge. The current source that charges the RAMP capacitor is equal to 3 times the ISYNC current. The falling edge of the phase signal sets the CLK signal and discharges the RAMP capacitor until the next rising edge of the phase signal. The RAMP capacitor is discharged to ground by a low impedance (100) n-channel MOSFET. The input impedance at SYNC pin is 2.5k which is normally much smaller than the external SYNC pin resistance. The RAMP and SYNC functions illustrated in Figure 2 provide line voltage feed-forward to improve the regulation of the auxiliary output when the input voltage of the main converter changes. Varying the input voltage to the main converter produces proportional variations in amplitude of the phase signal. The main channel PWM controller adjusts the pulse width of the phase signal to maintain constant volt*seconds and a regulated main output as shown in Figure 3. The variation of the phase signal amplitude and duration are reflected in the slope and duty cycle of the RAMP signal of the LM25115A (ISYNC phase signal amplitude). As a result, the duty cycle of the LM25115A is automatically adjusted to regulate the auxiliary output voltage with virtually no change in the PWM threshold voltage. Transient line regulation is improved because the PWM duty cycle of the auxiliary converter is immediately corrected, independent of the delays of the voltage regulation loop. Low Drop-Out Bias Regulator (VCC) The LM25115A contains an internal LDO regulator that operates over an input supply range from 4.5V to 30V. The output of the regulator at the VCC pin is nominally regulated at 7V and is internally current limited to 40mA. VCC is the main supply to the internal logic, PWM controller, and gate driver circuits. When power is applied to the VBIAS pin, the regulator is enabled and sources current into an external capacitor connected to the VCC pin. The recommended output capacitor range for the VCC regulator is 0.1uF to 100uF. When the voltage at the VCC pin reaches the VCC undervoltage lockout threshold of 4.25V, the controller is enabled. The controller is disabled if VCC falls below 4.0V (250mV hysteresis). In applications where an appropriate regulated dc bias supply is available, the LM25115A controller can be powered directly through the VCC pin instead of the VBIAS pin. In this configuration, it is recommended that the VCC and the VBIAS pins be connected together such that the external bias voltage is applied to both pins. The allowable VCC range when biased from an external supply is 4.5V to 7V. 30008312 FIGURE 2. Line Feed-Forward Diagram www.national.com 10 LM25115A 30008313 FIGURE 3. Line Feed-Forward Waveforms The recommended SYNC input current range is 50A to 150A. The SYNC pin resistor (RSYNC) should be selected to set the SYNC current (ISYNC) to 150A with the maximum phase signal amplitude, V PHASE(max). This will guarantee that ISYNC stays within the recommended range over a 3:1 change in phase signal amplitude. The SYNC pin resistor is therefore: VOUT(final) = regulator output set point Pull-up current for the error amplifier output is provided by an internal 300A current source. The PWM threshold signal at the COMP pin can be controlled by either the open drain error amplifier or the open drain current amplifier connected through the CO pin to COMP. Since the internal error amplifier is configured as an open drain output it can be disabled by connecting FB to ground. The current sense amplifier and current limiting function will be described in a later section. RSYNC = (VPHASE(max) / 150A) - 2.5k Once ISYNC has been established by selecting RSYNC, the RAMP signal slope/amplitude may be programmed by selecting the proper RAMP pin capacitor value. The RAMP signal slope should be selected to provide adequate slope compensation for the Valley current mode control scheme (Please refer to the Valley current mode section). The recommended peak amplitude of the ramp waveform is 1.75V. Power-Up/Power-Down Tracking The LM25115A can track the output of a master power supply during soft start by connecting a resistor divider to the TRACK pin (Figure 4). Therefore, the output voltage slew rate of the LM25115A will be controlled by the master supply for loads that require precise sequencing. In order to track properly the output voltage of the LM25115A must be lower than the output voltage of the master supply. One way to use the tracking feature is to design the tracking resistor divider so that the master supply output voltage (VOUT1) and the LM25115A output voltage (VOUT2) both rise together and reach their target values at the same time. For this case, the equation governing the values of the tracking divider resistors RT1 and RT2 is: Error Amplifier and Soft-Start (FB, CO, COMP & TRK/SS) An internal wide bandwidth error amplifier is provided within the LM25115A for voltage feedback to the PWM controller. The amplifier's inverting input is connected to the FB pin. The output of the auxiliary converter is regulated by connecting a voltage setting resistor divider between the output and the FB pin. Loop compensation networks are connected between the FB pin and the error amplifier output (COMP). The amplifier has two non-inverting inputs. The first non-inverting input connects to a 0.75V bandgap reference while the second noninverting input connects to the TRK/SS pin and it has 15 A pull-up current source. The TRK/SS pin can be tied to an external resistor divider from the master output for tracking, or it can be tied to a capacitor for soft-start . TRK/SS is the reference input to the amplifier when the voltage applied to the pin is < 0.75V. For higher inputs, the internal reference controls the amplifier. When the VCC voltage is below the UVLO threshold, the TRK/SS pin is discharged to ground. When VCC rises and exceeds the positive going UVLO threshold (4.25V), the TRK/SS pin is released and allowed to rise. If an external capacitor is connected to the TRK/SS pin, it will be charged by the internal 15uA pull-up current source to gradually increase the non-inverting input of the error amplifier to 0.75V. During start-up, the output of the LM25115A converter will follow the following equation: A value of 10k (1%) is recommended for RT2 as a good compromise between high precision and low quiescent current through the divider. If the master supply voltage was 3.3V and the LM25115A output voltage was 2.5 V, then the value of RT1 needed to give the two supplies identical soft start times would be 2.94 k (1%). The timing diagram and waveforms for the equal soft start time configuration are shown in Figure 5 and Figure 6. VOUT(t) = VOUT(final) x15 A x t /(.75 Vx Css ) Where Css = external Soft-Start capacitor 11 www.national.com LM25115A Alternatively, the tracking feature can be used to create equal slew rates between the output voltages of the master supply and the LM25115A. This method ensures that the output voltage of the LM25115A always reaches regulation before the output voltage of the master supply. In this case, the tracking resistors can be determined based on the following equation: Again, a value of 10k 1% is recommended for RT2. For the case of VOUT1 = 3.3V and VOUT2 = 2.5V, RT1 should be 4.32 k 1%. The timing diagram and the waveforms for equal slew rates configuration are shown in Figure 7 and Figure 8. 30008329 FIGURE 4. 30008330 FIGURE 7. 30008331 FIGURE 5. 30008328 Vphase = 10V CH1 = Master output, 1V/Div CH2 = COMP, 5/Div CH3 = Iout, 1A/Div CH4 = SSPR Output (Slave), 1V/Div Horizontal Resolution= 200 s/Div 30008327 Vphase = 10V CH1 = Master output, 1V/Div CH2 = COMP, 5/Div CH3 = Iout, 1A/Div CH4 = SSPR Output (Slave), 1V/Div Horizontal Resolution= 200 s/Div FIGURE 8. Tracking with Equal Slew Rate FIGURE 6. Tracking with Equal Soft Start Time www.national.com 12 Unlike conventional voltage mode controllers, the LM25115A implements leading edge pulse width modulation. A current source equal to 3 times the ISYNC current is used to charge the capacitor connected to the RAMP pin as shown in Figure 9. The ramp signal and the output of the error amplifier (COMP) are combined through a resistor network to produce a voltage ramp with variable dc offset (CRMIX in Figure 9). The high-side MOSFET which drives the HS pin is held in the off state at the beginning of the phase signal. When the voltage of CRMIX exceeds the internal threshold voltage CV, the PWM comparator turns on the high-side MOSFET. The HS pin rises and the MOSFET delivers current from the main converter phase signal to the output of the auxiliary regulator. The PWM cycle ends when the phase signal falls and power is no longer supplied to the drain of the high-side MOSFET. 30008314 FIGURE 9. Synchronization and Leading Edge Modulation 30008320 FIGURE 10. Leading versus Trailing Edge Modulation 13 www.national.com LM25115A Leading edge modulation of the auxiliary PWM controller is required if the main converter uses peak current mode control. If trailing edge modulation were used, the additional load on the transformer secondary from the auxiliary channel would be drawn only during the first portion of the phase signal pulse. Referring to Figure 10, the turn-off of the high- side MOSFET of the auxiliary regulator would create a non-monotonic negative step in the transformer current. This negative current step would produce instability in a peak current mode controller. With leading edge modulation, the additional load presented by the auxiliary regulator on the transformer secondary will be present during the latter portion of the phase signal. This positive step in the phase signal current can be accommodated by a peak current mode controller without instability. Leading Edge Pulse Width Modulation LM25115A old (CV), the PWM comparator turns on the high-side MOSFET. Insure that the Vbias voltage is at least 3V above the regulated output voltage (VOUT) to provide enough headroom for the current sense amplifier. Valley current mode control improves the control loop stability and bandwidth. It also eliminates the R-C lead network in the feedback path that is normally required with voltage mode control (Figure 12). Eliminating the lead network not only simplifies the compensation, but also reduces sensitivity to output noise that could pass through the lead network to the error amplifier. The design of the voltage feedback path through the error amp begins with the selection of R1 and R2 in Figure 12 to set the regulated output voltage. The steady state output voltage after soft-start is determined by the following equation: Valley Current Mode Control The LM25115A controller uniquely utilizes the elements and benefits of valley current mode control in conjunction with leading edge modulation to correct changes in output voltage due to line and load transients. Contrary to peak current mode control, valley current mode control turns on the high-side MOSFET when the inductor valley current reaches a programmable threshold. This programmable threshold (CRMIX) is the sum of the output of voltage error amplifier and the RAMP signal generated at the RAMP pin. Valley current mode control experiences sub-harmonic oscillation when the duty ratio, D, is less than or equal to 50%. Therefore, adequate slope compensation is needed for the proper operation across the full range of the duty ratio. The RAMP signal is proportional to the input voltage and it provides the required slope compensation for the valley current mode scheme. The desired RAMP pin capacitance can be calculated from the following equation: VOUT(final) = 0.75V x (1+R1/R2) The parallel impedance of the R1, R2 resistor divider should be approximately 2k (between 0.5k and 5k). Lower resistance values may not be properly driven by the error amplifier output and higher feedback resistances can introduce noise sensitivity. The next step in the design process is selection of R3, which sets the ac gain of the error amplifier. The capacitor C1 is connected in series with R3 to increase the dc gain of the voltage regulation loop and improve output voltage accuracy. The corner frequency set by R3 x C1 should be less than 1/10th of the cross-over frequency of the overall converter such that capacitor C1 does not add phase lag at the crossover frequency. CRAMP = (0.05 x L) /(RSYNC x RSENSE) Where L is the power inductor, RSYNC is the SYNC pin resistor and RSENSE is the current sense resistor. The current sense amplifier shown in Figure 11 monitors the inductor current as it flows through a sense resistor connected between CS and VOUT. The voltage gain of the sense amplifier is nominally equal to 16. The current sense output signal is shifted by 1.27V to produce the internal CV reference signal. The CV signal is applied to the negative input of the PWM comparator and compared to CRMIX as illustrated in Figure 11. Therefore when CRMIX exceeds the PWM thresh- 30008315 FIGURE 11. Current Sensing and Limiting www.national.com 14 LM25115A 30008316 FIGURE 12. Voltage Sensing and Feedback comparator will inhibit output pulses. Once the fault condition is removed, the fast current limit amplifier will release COMP. Therefore, the CRMIX signal will increase to a normal operating threshold and the switching will resume (Figure 14). A current limit fold-back feature is provided by the LM25115A to reduce the peak output current delivered to a shorted load. When the common mode input voltage to the current sense amplifier (CS and VOUT pins) falls below 2V, the current limit threshold is reduced from the normal level. At common mode voltages > 2V, the current limit threshold is nominally 45mV. When VOUT is reduced to 0 V the current limit threshold drops to 39mV to reduce stress on the inductor and power MOSFETs. Current Limiting (CS, CO and VOUT) Current limiting is implemented through the current sense amplifier as illustrated in Figure 11. The current sense amplifier monitors the inductor current that flows through a sense resistor connected between CS and VOUT. The voltage gain of the current sense amplifier is nominally equal to 16. The output of current sense signal is shifted by 1.27V to produce the internal CV reference signal. The CV signal drives two current limit amplifiers. Both of the current limit amplifiers have open drain (sink only) output stages which are connected to the CO pin. The CO pin is typically connected to the COMP pin through a diode (the cathode is connected to the CO pin and the anode is connected to the COMP pin). The slow current limit amplifier has a nominal transconductance of 5 mA/V and provides constant current mode operation at the desired current limit set point. The fast current limit amplifier has nominal current pull-down capability of 100mA and provides protection against fast over-current conditions. During normal operation, the voltage error amplifier controls the COMP pin voltage which adjusts the PWM duty cycle by varying the internal CRMIX level. However when the current sense input voltage, VCL, exceeds 45mV, the slow current limit amplifier gradually pulls down on COMP through the CO pin. Pulling COMP low reduces the CRMIX signal and thereby reducing the operating duty cycle. By controlling the operating duty cycle, the slow current limit amplifier will force a constant current mode of operation at the desired current limit set point (Figure 13). A resistor in series with a capacitor are connected from the CO Pin to ground to provide adequate control loop compensation for the slow current limit (Figure 11). The desired current limit set point, ILimit, can be programmed by selecting the proper current sense resistor, RSENSE,using the following equation: 30008325 Vphase=10V CH1 = CO, 5V/Div CH2 = COMP, 5/Div CH3 = Iout, 5A/Div CH4 = SSPR Switch Signal, 5V/Div Horizontal Resolution= 2 s/Div RSENSE = 0.045 V/ ILimit In the event that the current sense input voltage, VCL, exceeds 60mV, the fast current limit amplifier will pull down hard on COMP through the CO pin. This will reduce the CRMIX signal to a voltage below the CV signal level. Therefore, the PWM FIGURE 13. SSPR Steady State Current Limit (Output Shorted) 15 www.national.com LM25115A dead-time control to avoid shoot through currents. The adaptive dead-time control circuit monitors the state of each driver to ensure that one MOSFET is turned off before the other is turned on. The HB and VCC capacitors should be placed close to the pins of the LM25115A to minimize voltage transients due to parasitic inductances and the high peak output currents of the drivers. The recommended range of the HB capacitor is 0.047F to 0.22F. Both drivers are controlled by the PWM logic signal from the PWM latch. When the phase signal is low, the outputs are held in the reset state with the low-side MOSFET on and the high-side MOSFET off. When the phase signal switches to the high state, the PWM latch reset signal is de-asserted. The high-side MOSFET remains off until the PWM latch is set by the PWM comparator (CRMIX > CV as shown in Figure 9). When the PWM latch is set, the LO driver turns off the lowside MOSFET and the HO driver turns on the high-side MOSFET. The high-side pulse is terminated when the phase signal falls and SYNC input comparator resets the PWM latch. 30008326 Vphase=10V CH1 = CO, 5V/Div CH2 = COMP, 5/Div CH3 = Iout, 10A/Div CH4 = SSPR Switch Signal, 4V/Div Horizontal Resolution= 20 s/Div Thermal Protection Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction temperature limit is exceeded. When activated, typically at 165 degrees Celsius, the controller is forced into a low power standby state with the output drivers and the bias regulator disabled. The device will restart when the junction temperature falls below the thermal shutdown hysteresis, which is typically 25 degrees. The thermal protection feature is provided to prevent catastrophic failures from accidental device overheating. FIGURE 14. SSPR Short Circuit Transient (No-Load to Short-Circuit) Negative Current Limit Under certain conditions synchronous buck regulators are capable of sinking current from the output capacitors. This energy is stored in the inductor and returned to the input source. The LM25115A detects this current reversal by detecting a negative voltage being developed across the current sense resistor. The intent of this negative current comparator is to protect the low-side MOSFET from excessive currents. Excessive negative current can also lead to a large positive voltage spike on the HS pin at the turn-off of the low-side MOSFET. This voltage spike may damage the chip if its magnitude exceeds the maximum voltage rating of the part. The negative current comparator threshold is sufficiently negative to allow inductor current to reverse at no load or light load conditions. It is not intended to support discontinuous conduction mode with diode emulation by the low-side MOSFET. The negative current comparator shown in Figure 11 monitors the CV signal and compares this signal to a fixed 1V threshold. This corresponds to a negative VCL voltage between CS and VOUT of -17mV. The negative current limit comparator turns off the low-side MOSFET for the remainder of the cycle when the VCL input falls below this threshold. Standalone DC/DC Synchronous Buck Mode The LM25115A can be configured as a standalone DC/DC synchronous buck controller. In this mode the LM25115A uses leading edge modulation in conjunction with valley current mode control to control the synchronous buck power stage. The internal oscillator within the LM25115A sets the clock frequency for the high and low-side drivers of the external synchronous buck power MOSFETs . The clock frequency in the synchronous buck mode is programmed by the SYNC pin resistor and RAMP pin capacitor. Connecting a resistor between a dc bias supply and the SYNC pin produces a current, ISYNC, which sets the charging current of the RAMP pin capacitor. The RAMP capacitor is charged until its voltage reaches the peak ramp threshold of 2.25V. The RAMP capacitor is then discharged for 300ns before beginning a new PWM cycle. The 300ns reset time of the RAMP pin sets the minimum off-time of the PWM controller in this mode. The internal clock frequency in the synchronous buck mode is set by ISYNC, the ramp capacitor, the peak ramp threshold, and the 300ns deadtime. Gate Driver Outputs (HO & LO) The LM25115A provides two gate driver outputs, the floating high-side gate driver HO and the synchronous rectifier lowside driver LO. The low-side driver is powered directly by the VCC regulator. The high-side gate driver is powered from a bootstrap capacitor connected between HB and HS. An external diode connected between VCC and HB charges the bootstrap capacitor when the HS is low. When the high-side MOSFET is turned on, HB rises with HS to a peak voltage equal to VCC + VHS - VD where VD is the forward drop of the external bootstrap diode. Both output drivers have adaptive www.national.com FCLK 1 / ((CRAMP x 2.25V) / (ISYNC x 3) + 300ns) See the LM5115 dc evaluation board application note (AN-1367) for more details on the synchronous buck mode. Please note that LM25115A is similar to LM5115 except for the tracking feature. 16 FIGURE 15. LM25115A Secondary Side Post Regulator (Inputs from LM5025 Forward Active Clamp Converter, 36V to 78V) 30008317 LM25115A Application Circuit 17 www.national.com LM25115A Physical Dimensions inches (millimeters) unless otherwise noted TSSOP-16 Outline Drawing NS Package Number MTC16 www.national.com 18 LM25115A Notes 19 www.national.com LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated