SIDACtor® Protection Thyristors
80
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Broadband Optimized™ Protection
MC Series - Modified TO-220
Electrical Characteristics
MC Series Modified TO-220 are low capacitance
SIDACtor® devices designed to protect various types
of broadband equipment from damaging overvoltage
transients.
The series provides a robust single port solution that
enables equipment to comply with various global
regulatory standards while limiting the impact to
broadband signals.
1
2
3
(T)
(R)
(G)
Description
Applicable Global Standards
Features and Benefits
t Low voltage overshoot
t Low on-state voltage
t Does not degrade with
use
t Fails short circuit when
surged in excess of
ratings
t Robust Modified TO-220
Package
t 40% lower capacitance
than our Baseband
Protectors, for
applications that
demand greater signal
integrity
t Custom lead forms
available
Agency Approvals
Agency Agency File Number
E133083
Schematic Symbol
Pinout Designation
PIN 1
PIN 2
PIN 3
t TIA-968-A
t TIA-968-B
t ITU K.20/21 Enhanced
Level
t ITU K.20/21 Basic Level
t GR 1089 Inter-building*
t GR 1089 Intra-building*
t IEC 61000-4-5
t YD/T 1082
t YD/T 993
t YD/T 950
*A-rated parts require series resistance
Part Number Marking
VDRM
@lDRM=5μA
VS
@100V/μs
VDRM
@lDRM=5μA
VS
@100V/μs IHISIT
VT @ IT=2.2
Amps Capacitance
V min V max V min V max mA min mA
max
A
max V min
Pins 1-2, 3-2 Pins 1-3 Pins 1-2, 3-2
P0302AAMCLxx P0302AAMC 6 25 12 50 50 800 2.2 4
See
Capacitance
Values Table
P0602AAMCLxx P0602AAMC 25 40 50 80 50 800 2.2 4
P0602ACMCLxx P0602ACMC 25 40 50 80 50 800 2.2 4
P1402ACMCLxx P1402ACMC 58 77 116 154 150 800 2.2 4
P1602ACMCLxx P1602ACMC 65 95 130 190 150 800 2.2 4
P2202ACMCLxx P2202ACMC 90 130 180 260 150 800 2.2 4
P2702ACMCLxx P2702ACMC 120 160 240 320 150 800 2.2 4
P3002ACMCLxx P3002ACMC 140 180 280 360 150 800 2.2 4
P3602ACMCLxx P3602ACMC 170 220 340 440 150 800 2.2 4
P4202ACMCLxx P4202ACMC 190 250 380 500 150 800 2.2 4
Table continues on next page.
SIDACtor® Protection Thyristors
81
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Broadband Optimized™ Protection
Capacitance Values
Part Number
pF
Pin 1-2 / 3-2
Tip-Ground, Ring-Ground
pF
Pin 1-3
Tip-Ring
MIN MAX MIN MAX
P0302AAMCLxx 25 55 15 35
P0602AAMCLxx 15 35 10 20
P0602ACMCLxx 25 45 10 25
P1402ACMCLxx 40 60 20 35
P1602ACMCLxx 35 55 20 35
P2202ACMCLxx 45 70 25 40
P2702ACMCLxx 40 60 20 35
P3002ACMCLxx 35 55 20 35
P3602ACMCLxx 35 50 15 30
P4202ACMCLxx 30 50 15 30
P4802ACMCLxx 30 45 15 30
P6002ACMCLxx 30 45 15 25
Surge Ratings
Series
IPP ITSM
50/60 Hz di/dt
0.2x310 1
0.5x700 2
2x10 1
2x10 2
8x20 1
1.2x50 2
10x160 1
10x160 2
10x560 1
10x560 2
5x320 1
9x720 2
10x360 1
10x360 2
10x1000 1
10x1000 2
5x310 1
10x700 2
A min A min A min A min A min A min A min A min A min A min A/μs Max
A20 15015090 507575 45 7520500
C 50 500 400 200 150 200 175 100 200 30 500
Electrical Characteristics (continued)
Part Number Marking
VDRM
@lDRM=5μA
VS
@100V/μs
VDRM
@lDRM=5μA
VS
@100V/μs IHISIT
VT @ IT=2.2
Amps Capacitance
V min V max V min V max mA min mA
max
A
max V min
Pins 1-2, 3-2 Pins 1-3 Pins 1-2, 3-2
P4802ACMCLxx P4802ACMC 220 300 440 600 150 800 2.2 4 See
Capacitance
Values Table
P6002ACMCLxx P6002ACMC 275 350 550 700 150 800 2.2 4
Notes:
- Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted).
- Devices are bi-directional (unless otherwise noted).
- XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack. Special order item -- contact factory.)
Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias.
Notes:
1 Current waveform in μs
2 Voltage waveform in μs
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product.
- IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$
- The device must initially be in thermal equilibrium with -40°C < TJ <¡$
SIDACtor® Protection Thyristors
82
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Broadband Optimized™ Protection
Package Symbol Parameter Value Unit
Modified
TO-220
PIN 1
PIN 2
PIN 3
TJOperating Junction Temperature Range UP °C
TSStorage Temperature Range UP °C
R0JA Thermal Resistance: Junction to Ambient 50 °C/W
Thermal Considerations
IH
IT
IS
IDRM
VDRM
VT
+V
-V
+I
-I
VS
50
100
0
t
r
t
d
0
Peak
Value
Half Value
t – Time (μs)
I
PP
– Peak Pulse Current – %I
PP
t
r
= rise time to peak value
t
d
= decay time to half value
Waveform = t
r
x t
d
V-I Characteristics tr x td Pulse Waveform
25°C
Case Temperature (T
C
) - ºC
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
-40 -20 0 20 40 60 80 100 120 140 160
Ratio of I
H
I
H
(T
C
= 25ºC)
Normalized VS Change vs. Junction Temperature
Normalized DC Holding Current vs. Case Temperature
-8
-40 -20 0 20 40 60 80 100 120 140 160
-6
-4
0
2
4
6
8
10
12
14
Junction Temperature (T
J
) – °C
Percent of V
S
Change – %
25 °C
SIDACtor® Protection Thyristors
83
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Broadband Optimized™ Protection
Time
Temperature
T
P
T
L
T
S(max)
T
S(min)
25
t
P
t
L
t
S
time to peak temperature
(t 25ºC to peak)
Ramp-down
Ramp-up
Preheat
Critical Zone
T
L
to T
P
Figure 1
Soldering Parameters
Physical Specifications Environmental Specifications
Lead Material Copper Alloy
Terminal Finish 100% Matte-Tin Plated
Body Material UL recognized epoxy meeting flammability
classification 94V-0
High Temp Voltage
Blocking
80% Rated VDRM (VAC Peak ¡$PS¡$
504 or 1008 hrs. MIL-STD-750 (Method 1040)
JEDEC, JESD22-A-101
Temp Cycling
¡$UP¡$NJOEXFMMVQUP
cycles. MIL-STD-750 (Method 1051) EIA/JEDEC,
JESD22-A104
Biased Temp &
Humidity
52 VDC¡$3)VQUPIST&*"
JEDEC, JESD22-A-101
High Temp Storage ¡$IST.*-45%.FUIPE
JEDEC, JESD22-A-101
Low Temp Storage -65°C, 1008 hrs.
Thermal Shock
¡$UP¡$NJOEXFMMTFDUSBOTGFS
10 cycles. MIL-STD-750 (Method 1056) JEDEC,
JESD22-A-106
Autoclave (Pressure
Cooker Test)
¡$3)BUNVQUPIST&*"
JEDEC, JESD22-A-102
Resistance to Solder
Heat ¡$TFDT.*-45%.FUIPE
Moisture Sensitivity
Level
3)¡$ISTSFnPXDZDMFT
¡$1FBL+&%&$+45%-FWFM
Reflow Condition Pb-Free assembly
(see Fig. 1)
Pre Heat
- Temperature Min (Ts(min))¡$
- Temperature Max (Ts(max))¡$
- Time (Min to Max) (ts)60-180 secs.
Average ramp up rate (Liquidus Temp (TL)
to peak) 3°C/sec. Max.
TS(max) to TL - Ramp-up Rate 3°C/sec. Max.
Reflow
- Temperature (TL) (Liquidus) ¡$
- Temperature (tL)60-150 secs.
Peak Temp (TP)¡$
Time within 5°C of actual Peak Temp (tp)30 secs. Max.
Ramp-down Rate 6°C/sec. Max.
Time 25°C to Peak Temp (TP)8 min. Max.
Do not exceed ¡$
SIDACtor® Protection Thyristors
84
Revised: February 22, 2011
© 2011 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Broadband Optimized™ Protection
Part Marking
Packing Options
Part Numbering
Package
Type Description Quantity Added Suffix Industry
Standard
A
Modified TO-220
Tape and Reel Pack 700 RP EIA-468-B
Modified TO-220
Bulk Pack 500 N/A N/A
Modified TO-220,
Type 60 Lead Form
Bulk Pack
500
60
(special order item,
contact factory for details)
N/A
CONSTRUCTION VARIABLE
PACKING OPTIONS
I
PP
RATING
RoHS COMPLIANT
TYPE
P = SIDACtor
P MC L xx
MEDIAN VOLTAGE
PACKAGE TYPE
xxx 2
A
x
MC Series
Blank, RP or 60
-- for Type 60 orders, contact factory xxxxx
XXXXXXXXX Part Marking Code
(Refer to Electrical Characteristics Table)
Date Code
Tape and Reel Specification — Modified TO-220
1.626
(41.15)
0.720
(18.29) 0.360
(9.14)
0.240
(6.10) 0.019
(0.5)
0.750 ± 0.010
(19.05 ± 0.25)
0.500
(12.7)
0.100
(2.54) 0.100
(2.54)
14.173 (360.0)
Dimensions are in inches
(and millimeters).
1.968
(50.0)
Direction of Feed
Dimensions - Modified TO-220
D
F
P
G
A O
Tem p er at u r e
Measurement
Po i n t
PIN 3
PIN 2
PIN 1
J
H
L
KM
N
The modified TO-220 package is designed to
meet mechanical standards as set forth in
JEDEC publication number 95.
Inches Millimeters
Min Max Min Max
A 0.400 0.410 10.16 10.42
D 0.360 0.375 9.14 9.53
F 0.110 0.130 2.80 3.30
G 0.540 0.575 13.71 14.61
H 0.025 0.035 0.63 0.89
J 0.195 0.205 4.95 5.21
K 0.095 0.105 2.41 2.67
L 0.060 0.075 1.52 1.90
M 0.070 0.085 1.78 2.16
N 0.018 0.024 0.46 0.61
O 0.178 0.188 4.52 4.78
P 0.290 0.310 7.37 7.87
