LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 Single Supply Quad Comparators http://onsemi.com These comparators are designed for use in level detection, low-level sensing and memory applications in consumer, automotive, and industrial electronic applications. Features * * * * * * * * * * SOIC-14 D SUFFIX CASE 751A 14 Single or Split Supply Operation Low Input Bias Current: 25 nA (Typ) Low Input Offset Current: 5.0 nA (Typ) Low Input Offset Voltage Input Common Mode Voltage Range to GND Low Output Saturation Voltage: 130 mV (Typ) @ 4.0 mA TTL and CMOS Compatible ESD Clamps on the Inputs Increase Reliability without Affecting Device Operation NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant 1 PDIP-14 N, P SUFFIX CASE 646 14 1 TSSOP-14 DTB SUFFIX CASE 948G 14 1 PIN CONNECTIONS Output 2 1 14 Output 3 Output 1 2 13 Output 4 VCC 3 12 GND - Input 1 4 11 + Input 4 10 - Input 4 9 + Input 3 8 - Input 3 + Input 1 5 - Input 2 6 + Input 2 7 * 1 ) 4 *2 ) 3 ) * ) * (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 8 of this data sheet. (c) Semiconductor Components Industries, LLC, 2010 November, 2010 - Rev. 19 1 Publication Order Number: LM339/D LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 MAXIMUM RATINGS Rating Symbol Power Supply Voltage VCC LM239/LM339/LM2901, V MC3302 Input Differential Voltage Range VIDR LM239/LM339/LM2901, V MC3302 Input Common Mode Voltage Range Value Unit Vdc +36 or 18 +30 or 15 Vdc 36 30 VICMR -0.3 to VCC Output Short Circuit to Ground (Note 1) ISC Continuous Power Dissipation @ TA = 25C Plastic Package Derate above 25C PD Vdc 1/RqJA 1.0 8.0 W mW/C Junction Temperature TJ 150 C Operating Ambient Temperature Range TA LM239 MC3302 LM2901 LM2901V, NCV2901 LM339 Storage Temperature Range Tstg ESD Protection at any Pin (Note 2) Human Body Model Machine Model VESD -25 to +85 -40 to +85 -40 to +105 -40 to +125 0 to +70 -65 to +150 C C V 1500 200 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC. Output short circuits to VCC can cause excessive heating and eventual destruction. 2. VESD rating for NCV/SC devices is: Human Body Model - 2000 V; Machine Model - 200 V. VCC - Input + Input GND NOTE: Diagram shown is for 1 comparator. Figure 1. Circuit Schematic http://onsemi.com 2 Output LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 ELECTRICAL CHARACTERISTICS (VCC = +5.0 Vdc, TA = +25C, unless otherwise noted) LM2901/2901V/ NCV2901 LM239/339 MC3302 Symbol Min Typ Max Min Typ Max Min Typ Max Unit Input Offset Voltage (Note 4) VIO - 2.0 5.0 - 2.0 7.0 - 3.0 20 mVdc Input Bias Current (Notes 4, 5) IIB - 25 250 - 25 250 - 25 500 nA IIO - 5.0 50 - 5.0 50 - 3.0 100 nA VICMR 0 - VCC -1.5 0 - VCC -1.5 0 - VCC -1.5 V RL = (For All Comparators) - 0.8 2.0 - 0.8 2.0 - 0.8 2.0 RL = , VCC = 30 Vdc - 1.0 2.5 - 1.0 2.5 - 1.0 2.5 AVOL 50 200 - 25 100 - 25 100 - V/mV - - 300 - - 300 - - 300 - ns - - 1.3 - - 1.3 - - 1.3 - ms ISink 6.0 16 - 6.0 16 - 6.0 16 - mA Vsat - 130 400 - 130 400 - 130 500 mV IOL - 0.1 - - 0.1 - - 0.1 - nA Characteristic (Output in Analog Range) Input Offset Current (Note 4) Input Common Mode Voltage Range Supply Current Voltage Gain ICC mA RL 15 kW, VCC = 15 Vdc Large Signal Response Time VI = TTL Logic Swing, Vref = 1.4 Vdc, VRL = 5.0 Vdc, RL = 5.1 kW Response Time (Note 6) VRL = 5.0 Vdc, RL = 5.1 kW Output Sink Current VI (-) +1.0 Vdc, VI(+) = 0, VO 1.5 Vdc Saturation Voltage VI(-) +1.0 Vdc, VI(+) = 0, Isink 4.0 mA Output Leakage Current VI(+) +1.0 Vdc, VI(-) = 0, VO = +5.0 Vdc 3. (LM239) Tlow = -25C, Thigh = +85 (LM339) Tlow = 0C, Thigh = +70C (MC3302) Tlow = -40C, Thigh = +85C (LM2901) Tlow = -40C, Thigh = +105 (LM2901V & NCV2901) Tlow = -40C, Thigh = +125C NCV2901 is qualified for automotive use. 4. At the output switch point, VO ] 1.4 Vdc, RS 100 W 5.0 Vdc VCC 30 Vdc, with the inputs over the full common mode range (0 Vdc to VCC -1.5 Vdc). 5. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state. 6. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical. http://onsemi.com 3 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 PERFORMANCE CHARACTERISTICS (VCC = +5.0 Vdc, TA = Tlow to Thigh [Note 7]) LM2901/2901V/ NCV2901 LM239/339 MC3302 Symbol Min Typ Max Min Typ Max Min Typ Max Unit Input Offset Voltage (Note 8) VIO - - 9.0 - - 15 - - 40 mVdc Input Bias Current (Notes 8, 9) IIB - - 400 - - 500 - - 1000 nA IIO - - 150 - - 200 - - 300 nA VICMR 0 - VCC -2.0 0 - VCC -2.0 0 - VCC -2.0 V Vsat - - 700 - - 700 - - 700 mV IOL - - 1.0 - - 1.0 - - 1.0 mA VID - - VCC - - VCC - - VCC Vdc Characteristic (Output in Analog Range) Input Offset Current (Note 8) Input Common Mode Voltage Range Saturation Voltage VI(-) +1.0 Vdc, VI(+) = 0, Isink 4.0 mA Output Leakage Current VI(+) +1.0 Vdc, VI(-) = 0, VO = 30 Vdc Differential Input Voltage All VI 0 Vdc 7. (LM239) Tlow = -25C, Thigh = +85 (LM339) Tlow = 0C, Thigh = +70C (MC3302) Tlow = -40C, Thigh = +85C (LM2901) Tlow = -40C, Thigh = +105 (LM2901V & NCV2901) Tlow = -40C, Thigh = +125C NCV2901 is qualified for automotive use. 8. At the output switch point, VO ] 1.4 Vdc, RS 100 W 5.0 Vdc VCC 30 Vdc, with the inputs over the full common mode range (0 Vdc to VCC -1.5 Vdc). 9. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state. 10. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical. + VCC + VCC R3 10 k Vin + VCC Rref Rref 10 k - Vref VO + R1 R2 Vref 10k R1 1.0 M Vref [ R3 Rref + R1 1.0 M R3 ] R1 / / Rref / / R2 VH = R1/ / Rref + R2 VO + 10 k VCC R1 R1 / / Rref R2 Vin 10 k Vref = VCC R1 Rref + R1 R2 [ R1 / / Rref Amount of Hysteresis VH R2 VH = [(V -V ] R2 + R3 O(max) O(min) [VO(max) - VO(min)] R2 Rref / / R1 Figure 2. Inverting Comparator with Hysteresis Figure 3. Noninverting Comparator with Hysteresis http://onsemi.com 4 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 Typical Characteristics (VCC = 15 Vdc, TA = +25C (each comparator) unless otherwise noted.) 48 42 I IB, INPUT BIAS CURRENT (nA) 1.20 1.00 0.80 TA = -55 C 36 TA = +25 C 30 TA = +125C 24 18 12 6.0 0 0.60 -50 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (C) 100 125 0 4.0 8.0 12 16 20 24 VCC, POWER SUPPLY VOLTAGE (Vdc) Figure 4. Normalized Input Offset Voltage 28 Figure 5. Input Bias Current 8.0 IO, OUTPUT CURRENT (mA) NORMALIZED OFFSET VOLTAGE 1.40 7.0 TA = +25 C 6.0 TA = -55 C 5.0 TA = +125C 4.0 3.0 2.0 1.0 0 100 0 200 300 400 500 Vsat, OUTPUT SATURATION VOLTAGE (mV) Figure 6. Output Sink Current versus Output Saturation Voltage VCC RS Vin Vref VCC 4.0 V + - VCC RS = Source Resistance R1 ] RS RL kW 1/4 MC14001 +15 100 1/4 MC7400 +5.0 10 CMOS TTL R1 VO + R2 R3 330 k 330 k R4 VCC (V) Device - + C R1 Logic 10 k 100 k RL 330 k VCC T1 T2 T1 = T2 = 0.69 RC 7.2 f[ C(mF) R2 = R3 = R4 R1 [ R2 // R3 // R4 Figure 7. Driving Logic Figure 8. Squarewave Oscillator http://onsemi.com 5 32 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 APPLICATIONS INFORMATION These quad comparators feature high gain, wide bandwidth characteristics. This gives the device oscillation tendencies if the outputs are capacitively coupled to the inputs via stray capacitance. This oscillation manifests itself during output transitions (VOL to VOH). To alleviate this situation input resistors < 10 kW should be used. The addition of positive feedback (< 10 mV) is also recommended. It is good design practice to ground all unused input pins. Differential input voltages may be larger than supply voltages without damaging the comparator's inputs. Voltages more negative than -300 mV should not be used. +15 V R1 8.2 k R4 220 k D1 6.8 k R2 Vin R5 220 k 10 k * ) Vin(min) 0.4 V peak for 1% phase distortion (Dq). VO Vin Vin(min) VCC 15 k R3 q 10 M * Vin D1 prevents input from going negative by more than 0.6 V. R1 + R2 = R3 R5 R3 for small error in zero crossing 10 + VEE 10 k VO VCC VEE Figure 9. Zero Crossing Detector (Single Supply) q VO Dq Figure 10. Zero Crossing Detector (Split Supplies) http://onsemi.com 6 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 ORDERING INFORMATION Package Shipping LM239DG SOIC-14 55 Units/Tube LM239DR2G SOIC-14 Device LM239DTBR2G TSSOP-14 2500 / Tape & Reel LM239NG PDIP-14 25 Units/Rail LM339DG SOIC-14 55 Units/Tube LM339DR2G LM339DTBR2G SOIC-14 TSSOP-14 2500 / Tape & Reel LM339NG PDIP-14 25 Units/Rail LM2901DG SOIC-14 55 Units/Rail LM2901DR2G SOIC-14 LM2901DTBR2G TSSOP-14 2500 / Tape & Reel LM2901NG PDIP-14 25 Units/Rail LM2901VDG SOIC-14 55 Units/Tube LM2901VDR2G SOIC-14 LM2901VDTBR2G TSSOP-14 LM2901VNG PDIP-14 NCV2901DR2G SOIC-14 NCV2901DTBR2G TSSOP-14 2500 / Tape & Reel 25 Units/Rail 2500 / Tape & Reel NCV2901CTR Bare Die 6000 / Tape & Reel MC3302DG SOIC-14 55 Units/Tube MC3302DR2G SOIC-14 MC3302DTBR2G MC3302PG TSSOP-14 PDIP-14 2500 / Tape & Reel 25 Units/Rail For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 MARKING DIAGRAMS PDIP-14 N, P SUFFIX CASE 646 14 14 14 LM339N AWLYYWWG 1 LM2901N AWLYYWWG LM239N AWLYYWWG 1 14 14 LM2901VN AWLYYWWG MC3302P AWLYYWWG 1 1 1 SOIC-14 D SUFFIX CASE 751A 14 14 14 LM339DG AWLYWW 1 14 LM239DG AWLYWW 1 LM2901DG AWLYWW 1 14 * LM2901VDG AWLYWW MC3302DG AWLYWW 1 1 TSSOP-14 DTB SUFFIX CASE 948G 14 14 339 ALYW G G 239 ALYW G G 1 14 1 14 14 2901 V ALYW G G 2901 ALYW G G 1 1 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location) *This marking diagram also applies to NCV2901. http://onsemi.com 8 * 3302 ALYW G G 1 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 PACKAGE DIMENSIONS PDIP-14 CASE 646-06 ISSUE P 14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B A F L N C -T- SEATING PLANE H G D 14 PL J K 0.13 (0.005) M M http://onsemi.com 9 DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10 _ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10 _ 0.38 1.01 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 PACKAGE DIMENSIONS SOIC-14 CASE 751A-03 ISSUE H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 8 -B- P 7 PL 0.25 (0.010) M 7 1 G -T- 0.25 (0.010) M T B S A DIM A B C D F G J K M P R J M K D 14 PL F R X 45 _ C SEATING PLANE B M S SOLDERING FOOTPRINT* 7X 7.04 14X 1.52 1 14X 0.58 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 PACKAGE DIMENSIONS TSSOP-14 CASE 948G-01 ISSUE B 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S N 2X 14 L/2 0.25 (0.010) 8 M B -U- L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S S DETAIL E K A -V- EEE CCC CCC EEE K1 J J1 DIM A B C D F G H J J1 K K1 L M SECTION N-N -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 11 MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 --- 1.20 --- 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ LM339, LM239, LM2901, LM2901V, NCV2901, MC3302 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative LM339/D