DC919A-F - ANALOG DEVICES - Datasheet.Directory

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

LTC2207, LTC2206, LTC2205, LTC2204, LTC2203, LTC2202

DESCRIPTION

Demonstration circuit 919 supports members of a

family of 16/14 BIT 130 MSPS ADCs. Each assem-

bly features one of the following devices: LTC2207,

LTC2206, LTC2205, LTC2204, LTC2203, or LTC2202

high speed, high dynamic range ADCs.

Other members of this family include the

LTC2208/LTC2208-14 16/14-Bit 130Msps ADC with

LVDS outputs. These 9x9mm QFN devices are sup-

ported by Demonstration circuit 854 (CMOS out-

puts only) or by Demonstration circuit 996 (LVDS

outputs).

Several versions of the 919A demo board support-

ing a single ended clock input, specifically targeted

for use with the 25Msps LTC2203 and 10Msps

LTC2202 A/D converters, are listed in Table 1.

LTC2204, LTC2205, LTC2206 and LTC2207 have

differential clock inputs but use a single ended

clock input for evaluation with the DC input on the

DC919 board. Depending on the required sample

rate and input frequency, the DC919 is supplied

with the appropriate ADC and with an optimized in-

put circuit. The circuitry on the analog inputs is op-

timized for analog input frequencies from DC to

70MHz or from 1MHz to 70MHz if using the trans-

former coupled input. For higher input frequencies,

contact the factory for support.

Design files for this circuit board are available.

Call the LTC factory.

LTC is a trademark of Linear Technology Corporation

Table 1.

DC919A Variants

DC919 VARIANTS ADC PART NUMBER RESOLUTION* MAXIMUM SAMPLE RATE INPUT FREQUENCY

919A-A LTC2207 16-Bit 105Msps DC - 70MHz

919A-B LTC2206 16-Bit 80Msps DC - 70MHz

919A-C LTC2205 16-Bit 65Msps DC - 70MHz

919A-D LTC2204 16-Bit 40Msps DC -70MHz

919A-E LTC2203 16-Bit 25Msps DC - 70MHz

919A-F LTC2202 16-Bit 10Msps DC - 70MHz

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

Table 2.

Performance Summary (TA = 25°C)

PARAMETER CONDITION VALUE

Supply Voltage Depending on sampling rate and the A/D converter provided,

this supply must provide up to 500mA.

Optimized for 3.3V

[3.15V 3.45V min/max]

Analog input range Depending on PGA Pin Voltage 1.5V

to 2.25V

Minimum Logic High 2.4V

Logic Input Voltages

Maximum Logic Low 0.8V

Minimum Logic High @ -1.6mA 2.3V (33Ω Series terminations) Logic Output Voltage

(74VCX245 output buffer, V

= 2.5V) Maximum Logic Low @ 1.6mA 0.7V (33Ω Series terminations)

Sampling Frequency (Convert Clock Frequency) See Table 1

Convert Clock Level 50 Ω Source Impedance, AC coupled or ground referenced

(Convert Clock input is capacitor coupled on board and ter-

minated with 50Ω.)

P-P 

2.5V

P-P

Sine Wave

or Square wave

Resolution See Table 1

Input frequency range See Table 1

SFDR See Applicable Data Sheet

SNR See Applicable Data Sheet

QUICK START PROCEDURE

Demonstration circuit 919 is easy to set up to evalu-

ate the performance of the LTC2207, LTC2206,

LTC2205, LTC2204, LTC2203, or LTC2202 A/D con-

verters. Refer to Figure 1 for proper measurement

equipment setup and follow the procedure below:

SETUP

If a DC718 QuickDAACS Data Analysis and Collection

System was supplied with the DC919 demonstration

circuit, follow the DC718 Quick Start Guide to install

the required software and for connecting the DC718 to

the DC919 and to a PC running Windows98, 2000 or

XP.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

Figure 1.

DC919 Setup (zoom in for detail)

DC919 DEMONSTRATION CIRCUIT BOARD JUMPERS

The DC919 demonstration circuit board

should have the following jumper set-

tings as default: (as per figure 1)

JP1: Output clock polarity: GND

JP2: SENSE: VDD, (Internal reference)

JP3: PGA: GND 2.25V range

JP4: RAND: GND Not randomized

JP5: SHDN: GND Not Shutdown

JP6: DITH: GND No internal dithering

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

APPLYING POWER AND SIGNALS TO THE DC919

DEMONSTRATION CIRCUIT

If a DC718 is used to acquire data from the DC919,

the DC718 must FIRST be connected to a powered

USB port or provided an external 6-9V BEFORE ap-

plying +3.3V across the pins marked “+3.3V” and

“PWR GND” on the DC919. The DC919 demonstra-

tion circuit requires up to 500mA depending on the

sampling rate and the A/D converter supplied.

The DC718 data collection board is powered by the

USB cable and does not require an external power

supply unless it must be connected to the PC

through an un-powered hub in which case it must

be supplied an external 6-9V on turrets G7(+) and

G1(-) or the adjacent 2.1mm power jack.

ENCODE CLOCK

NOTE: This

a logic compatible input, contrary

to the majority of Linear technology ADC demo

boards. It is not terminated with 50Ω

ΩΩ

Ω.

Apply an encode clock to the SMA connector on the

DC919 demonstration circuit board marked “J3

ENCODE INPUT”.

For the best noise performance, the ENCODE INPUT

must be driven with a very low jitter source. A low

jitter 3.3V oscillator with direct connection through

a barrel is recommended.

If using a sinusoidal generator, the amplitude

should be as large as possible, up to 3V

P-P

13dBm, filtered and terminated with a 50Ω thru-

terminator. If a generator with 50Ω output imped-

ance is connected via a cable, it is recommended

that a thru-terminator be used. However, below 15

MHz, it is recommended that a square wave drive

be used.

If a sinusoidal ground referenced signal, or an AC

coupled signal is used, 1.5V-1.7V DC bias must be

introduced via a bias tee.

DC919 has provision for a popular surface mount

oscillator form and some population options to se-

lect this as the clock source. (Please see sche-

matic.)

If only sinusoidal or clipped sinusoid signal sources

are available as the clock source for scenarios in-

volving sampling rates less than 15-20Msps, it is

recommended that a divide by 4 or divide by 8 be

used. If the converter is to be used at very low

sampling rates approaching the minimum, a higher

divide ratio may be required. This is especially im-

portant if under-sampling.

If you want to use these converters at less than the

minimum sampling rate, it is recommended that

you run the ADC above the minimum rate, and

decimate. If over-sampling low frequencies, the

use of a sinusoid is potentially acceptable, but it

must be very clean or the low dVdT will result in a

great sensitivity to wideband noise in the clock

driver. .

The use of a divider may require a band-pass filter

prior to the divider in order to achieve best SNR as

the divider can exaggerate phase noise if it is sensi-

tive to GHz frequencies. Contact Linear technology

for recommendations or in some cases, available

clock sources or dividers.

Most generators require filtering or they will com-

promise both the SNR and the SFDR of the ADCs.

Generally datasheet FFT plots are taken with 10 pole

LC filters made by TTE (Los Angeles, CA) to sup-

press signal generator harmonics,

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

non-harmonically related spurs and broad band

noise. Low phase noise Agilent 8644B generators

are used with TTE band pass filters for both the

Clock input and the Analog input. In the case of the

LTC2203/2 we use a divide by 4.

This demo board is, populated by default for the dc

input path. There is a transformer mounted at T1,

but C4, C6, R9 and R13 are not populated. If a sin-

gle ended AC input is required, the DC input paths

must be disconnected by removing R26,27,31 &

32, and the above components installed.

If the transformer input is required, C4 & C6

should be 0.1uF X5R 0402, R9 and R13 should be

10 ohm 0402 resistors.

Note that this transformer (ETC1-1T) is poor below

1 MHz.

Reduced amplitude signals can be applied to 300

KHz. Applications below 300 KHz must be driven

directly via DC inputs.

As there are a significant number of these boards

that are customized, please confirm the population

of your board. The schematic below shows the de-

fault population, the photograph shows the popula-

tion of a transformer coupled version. This board

may also be populated with LTC2204-2207 for DC

drive applications, in which case, R33 is a 0.1uF

capacitor.

Apply the analog input signal of interest to the SMA

connector on the DC919 demonstration circuit

board marked “J2 ANALOG INPUT”. These inputs

are capacitive coupled to a Flux coupled transform-

ers ETC1-1T. In some cases, where these devices

are to be used in under-sampling scenarios, this

transformer should be replaced with an ETC1-1-13

Balun.

The DC919 can be modified for direct DC drive from

a suitable differential signal source.

This may be done by yourself or at special request

when you order the demo board.

If the DC input paths are populated with low value

(5.1 ohm) resistors at both ends of these transmis-

sion lines, you must provide a reasonably well bal-

anced differential drive with 1.25V common mode.

The spacing of these SMA connectors (0.8”) allows

them to be mated directly with demo boards for

devices such as the LT1993, LT1994, LT5514 and

others.

It is not recommended to drive this ADC in a single

ended fashion into a single DC input.

An internally generated conversion clock output is

available on pin 3 of J1 and the data samples are

available on Pins 7-37 of J1 which can be collected

via a logic analyzer, cabled to a development system

through a SHORT 2 to 4 inch long 40-pin ribbon

cable or collected by the DC718 QuickEval-II Data

Acquisition Board using the

PScope System Soft-

ware

provided or down loaded from the Linear

Technology website at

http://www.linear.com/software/. If a DC718 was

provided, follow the DC718 Quick Start Guide and

the instructions below.

If data is to be collected by a logic analyzer, pin 40

must be strapped to OVDD or 2.5V.

(Please see schematic.)

To start the data collection software if

“

PScope.exe

”, is installed (by default) in

\Program Files\LTC\PScope\, double click the

PScope Icon or bring up the run window under the

start menu and browse to the PScope directory and

select PScope.

Configure PScope for the appropriate variant of the

DC919 demonstration circuit by selecting the cor-

rect A/D Converter as installed on the DC919. Un-

der the “Configure” menu, go to “Device.” Under

the “Device” pull down menu, select device, either

LTC2202, LTC2203 or any of the pin-compatible 14-

Bit and 16-Bit parts up to LTC2207. Select the part

in the Device List and PScope will automatically

blank the last two LSBs when using a DC919 sup-

plied with a 14-Bit part. If you are operating with a

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

version of PScope that does not include these parts

in the device menu, you may manually configure as:

User configure

16-Bit (or 14-Bit if using -14 versions)

Alignment: Left-16

Bipolar (2’s complement)

Positive clock edge

Type: CMOS

If everything is hooked up properly, powered and a

suitable convert clock is present, clicking the “Col-

lect” button should result in time and frequency

plots displayed in the PScope window. Additional

information and help for

PScope

is available in the

DC718 Quick Start Guide and in the online help

available within the

PScope

program itself.

ANALOG INPUT NETWORK

For optimal distortion and noise performance the

RC network on the analog inputs should be opti-

mized for different analog input frequencies. At this

point in time, the circuit in Fig. 3 for input frequen-

cies below 70MHz. For input frequencies from

70MHz to 140MHz, the circuit in Fig. 2 is used.

These two input networks cover a broad bandwidth

and are not optimized for operation at a specific

input frequency.

In almost all cases, filters will be required on both

analog input and encode clock to provide data sheet

SNR.

Narrow band high Q filters may produce poor SNR

results with Dither enabled. 10% band-pass would

be preferred over 5% band-pass on the analog in-

put. The filters should be located close to the in-

puts to avoid reflections from impedance disconti-

nuities at the driven end of a long transmission line.

Most filters do not present 50 ohms outside the

pass-band.

In cases with long transmission lines, 3-10dB pads

may be required to obtain low distortion.

If your generator cannot deliver full scale signals

without distortion, you may benefit from a medium

power amplifier based on a Gallium Arsenide Gain

block prior to the final filter. This is particularly true

at higher frequencies where IC based operational

amplifiers may be unable to deliver the combination

of low noise figure and High IP3 point required. A

high order filter can be used prior to this final am-

plifier, and a relatively lower Q filter used between

the amplifier and the demo circuit.

For advice on drive circuits or for input frequencies

greater than 70MHz contact the factory for support.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC

Figure 2.

Analog Front End Circuit For 70MHz+ (1 of 2)

Figure 3.

Analog Front End Circuit For 1MHz < A

< 70MHz (1 of 2)

For input frequencies less than 5MHz, or greater than 150MHz, other input networks may be more appropri-

ate. Please consult the factory for suggestions on drivers and networks if your signal sources extend outside

these ranges, or if you experience difficulties driving these suggested networks.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 919

16-BIT 10 TO 105 MSPS ADC