PT11-21C/L41/TR8 - Everlight Electronics Co Ltd

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 1 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

Technical Data Sheet

1206 Package Phototransistor With Inner Lens

PT11-21C/L41/TR8

Features

․Fast response time

․High photo sensitivity

․Small junction capacitance

․Package in 8mm tape on 7” diameter reel

․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

․PT11-21C/L41/TR8 is a phototransistor in miniature SMD package

which is molded in a water clear plastic with flat top view lens.

The device is Spectrally matched to visible and infrared emitting

diode.

Applications

․Automatic door sensor

․Copier

․Game machine

․Infrared applied systm

Device Selection Guide Chip

LED Part No. Material Lens Color

PT Silicon Water clear

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 2 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

Emitter

Collector

PT11-21C/L41/TR8

Package Dimensions

Notes: 1.All dimensions are in millimeters

2.Tolerances unless dimensions ±0.1mm

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Units

Collector-Emitter Voltage VCEO 30 V

Emitter-Collector-Voltage VECO 5 V

Collector Current IC 20 mA

Operating Temperature Topr -25 ~ +85 ℃

Storage Temperature Tstg -40 ~ +85 ℃

Soldering Temperature Tsol 260 ℃

Power Dissipation at(or below)

25℃Free Air Temperature Pc 75 mW

Notes: *1:Soldering time≦5 seconds.

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 3 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

PT11-21C/L41/TR8

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Condition Min Typ Max Unit

Rang Of Spectral Bandwidth λ0.5 --- 400 --- 1100 nm

Wavelength Of Peak Sensitivity λP --- --- 940 --- nm

Collector-Emitter Breakdown

Voltage BVCEO IC=100μA

Ee=0mW/cm2 30 --- --- V

Emitter-Collector Breakdown

Voltage BVECO IE=100μA

Ee=0mW/cm2 5 --- --- V

Collector-Emitter Saturation

Voltage VCE(sat) IC=2mA

Ee=1m W/cm2 --- --- 0.4 V

Collector Dark Current ICEO VCE=20V

Ee=0mW/cm2 --- --- 100 nA

On State Collector Current IC(ON) VCE=5V

Ee=1mW /cm2 0.3 0.8 mA

Rise Time tr --- 15 ---

Fall Time tf

VCE=5V

IC=1mA

RL=1000Ω --- 15 ---

μS

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 4 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

0-25

20

40

50

025 8575 100

60

80

100

20

0

040

10 20 30 6050 70

100

60

40

80

140

120

160

2

0.001

0.01 0.1 1

2

10

0.01

0.1

1

10

C

100

0.2

0

0.4

700500300

Ta=25

0.8

0.6

1.0

C

13001100900

PT11-21C/L41/TR8

Typical Electro-Optical Characteristics Curves

Fig.1Collector Power Dissipation vs. Fig.2 Spectral Sensitivity

Ambient Temperature

Fig.3 Relative Collector Current vs. Fig.4 Collector Current vs.

Ambient Temperature Irradiance

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 5 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

10

100

10

25 50 75 100

10

4

00

2

1

6

8

23

14

12

4

PT11-21C/L41/TR8

Typical Electro-Optical Characteristics Curves

Fig.5 Collector Dark Current vs. Fig.6 Collector Current vs.

Ambient Temperature Collector-Emitter Voltage

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 6 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

PT11-21C/L41/TR8

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 7 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

PT11-21C/L41/TR8

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3

seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more

intervals, and do soldering of each terminal. Be careful because the damage of the product is often

started at the time of the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is

unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed

beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 8 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

PT11-21C/L41/TR8

Reliability Test Item And Condition

The reliability of products shall be satisfied with items listed below.

Confidence level：90%

LTPD：10%

NO. Item Test Conditions Test Hours/

Cycles

Sample

Sizes

Failure

Judgement

Criteria

Ac/Re

1 REFLOW Soldering TEMP.：260℃±5℃

5secs

6Mins 22pcs 0/1

2 Temperature Cycle H : +100℃ 15mins

5mins

L : -40℃ 15mins

50Cycles 22pcs 0/1

3 Thermal Shock H :+100℃ 5mins

10secs

L :-10℃ 5mins

50Cycles 22pcs 0/1

4 High Temperature

Storage

TEMP.：+100℃ 1000hrs 22pcs 0/1

5 Low Temperature

Storage

TEMP.：-40℃ 1000hrs 22pcs 0/1

6 DC Operating Life VCE=5V 1000hrs 22pcs 0/1

7 High Temperature/

High Humidity

85℃ / 85% R.H 1000hrs 22pcs

IC(ON)≦L×0.8

L：Lower

Specification

Limit

0/1

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 9 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

Emitter

Collector

PT11-21C/L41/TR8

Package Dimensions

Taping Dimensions

Unit:mm

Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 10 of 10

Device No：DPT-011-026 Prepared date：07-20-2005 Prepared by：Jaine Tsai

RoHS

PT11-21C/L41/TR8

Packing Quantity Specification

1.2000Pcs/1Volume，1Volume/1Bag

2.10Boxes/1Carton

Label Form Specification

CPN: Customer’s Production Number

P/N : Production Number

QTY: Packing Quantity

CAT: Ranks

HUE: Peak Wavelength

REF: Reference

LOT No: Lot Number

MADE IN TAIWAN: Production Place

Notes

1. Above specification may be changed without notice. EVERLIGHT will reserve authority on

material change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions

for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for

any damage resulting from use of the product which does not comply with the absolute

maximum ratings and the instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s

consent.

EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936

Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306

Tucheng, Taipei 236, Taiwan, R.O.C http:\\www.everlight.com

PT11-21C/L41/TR8