FTR-K1 SERIES ULTRA MINIATURE RELAY 2 POLES - 2 A (Slim Profile Signal Relay) FTR-B4 Series n FEATURES DPDT 2C l Ultra miniature slim type relay for surface mounting Height: 9.3 mm maximum (THT) 10 mm maximum (SMT) Weight: Approximately 1.0 g l Conforms to Bellcore & FCC part 68, and Telcordia & FCC part 68 l Conforms to UL1950 / CSA 950, IEC 950 / EN60950 spacing and high breakdown voltage Clearance: 1.0mm Creepage: 1.6mm Basic insulation, 150V working voltage, pollution degree 2 l High reliable birfuracted gold overlay silver contact l Low power consumption 140 mW (standard), 100 mW (latching) l RoHS compliant. Please see page 9 for more information l PARTNUMBER INFORMATION n [Example] (a) FTR-B4 (a) C A (b) (c) Relay type 4.5 Z - B 05 (d) (e) (f) (g) FTR-B4 : FTR-B4-Series (b) Terminal type C G S : Through hole : Surface mount : Surface mount, space saving (c) Coil type A B : Standard type : Latching type (1 coil) (d) Coil rated voltage 4.5 : 1.5.....24 VDC Coil rating table at page 3 (e) Contact material Z P : Gold overlay silver nickel (standard) : Gold overlay silver palladium (f) Relay enclosing direction *1 B : Standard enclosing direction (g) Number of relays per reel *2 05 : 500 (standard) Remarks: Actual marking on relay would not carry code FTR and be as below: Ordering code: FTR-B4CA4.5Z Actual marking: B4CA4.5Z *1 - Only surface mount types (G and S) are applicable *2 - All relays are packaged in tubes unless part number ends with -B05 1 FTR-K1 SERIES FTR-B4 SERIES n SPECIFICATION Item Contact Data Life Timing Data Insulation FTR-B4 ( ) A FTR-B4 ( ) B 2 form C Construction Bifurcated contacts (cross-bar) Material Gold overlay silver nickel / Gold overlay silver palladium Resistance (Initial) Max. 100 m at 1 A, 6 VDC Contact rating (resistive) 30VDC, 1A / 125VAC, 0.3A Max. carrying current 2A Max. switching voltage 250 VAC / 220VDC Max. switching power 62.5VA / 30W Min. switching load * 0.01mA, 10mVDC Mechanical Min. 50 x 106 operations Min. 20 x 106 operations DC load Min. 100 x 103 operations at 1A, 30VDC (at 0.5 Hz) AC load Min. 100 x 103 operations at 0.3A, 125VAC (at 0.5 Hz) Rated power 140mW - 230mW 100mW - 130mW Operate power 80mW - 130mW 57mW - 68mW Operating temperature range -40 C to +85 C (no frost) Operate (at nominal voltage, no bounce) Max. 3 ms Max. 3 ms (set) Release (at nominal voltage, no bounce) Max. 3 ms Max. 3 ms (reset) Resistance (initial) Min. 1,000M at 500VDC Dielectric strength Surge strength Clearance Creepage Other Latching type Configuration Electrical Coil Data Standard type Vibration resistance Shock Weight Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 1,500VAC (50/60Hz) 1min Adjacent contacts 1,000VAC (50/60Hz) 1min. Coil to contacts 2,500V, 2 x 10s standard wave Adjacent contacts 1.0 mm Open contacts 0.28 mm Coil and contacts 1.0 mm Adjacent contacts 1.0 mm Open contacts 0.28 mm Coil and contacts 1.60 mm Misoperation 10 to 55 Hz at double amplitude of 3 mm Endurance 10 to 55 Hz at double amplitude of 5 mm Misoperation 750m/s Endurance 1,000m/s Approximately 1 g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-B4 SERIES FTR-K1 SERIES n COIL RATING Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * Max. Coil Voltage (VDC) 1.5 1.5 16.1 1.13 0.15 3.53 003 3 64.3 2.25 0.3 7.05 4.5 4.5 145 3.38 0.45 10.58 006 6 257 4.5 0.6 14.10 009 9 579 6.75 0.9 21.15 012 12 1,028 9 1.2 28.20 024 24 2,504 18 2.4 56.40 Rated Power (mW) 140 230 Latching type (1 coil) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * Max. Coil Voltage (VDC) Set/Re-set current (mA) 1.5 1.5 22.5 1.13 -0.13 3.53 50 003 3 90 2.25 -2.25 7.05 25 4.5 4.5 203 3.38 -3.38 10.58 17 006 6 360 4.5 -4.5 14.10 13 009 9 810 6.75 -6.75 21.15 8 012 12 1,440 9 -9 28.20 6 024 24 4,800 18 -18 56.40 4 Rated Power (mW) 100 120 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E 63615 CSA C22.2 No. 14 LR 40304 0.5A, 125VAC (resistive) 1A, 30VDC (resistive) 0.3A, 110VDC (resistive) 2A, 30VDC (resistive) 3 FTR-K1 SERIES FTR-B4 SERIES n CHARACTERISTIC DATA l Standard type 4 FTR-K1 SERIES FTR-B4 SERIES l Latching type (1coil) 5 FTR-K1 SERIES FTR-B4 SERIES 6 FTR-K1 SERIES FTR-B4 SERIES n DIMENSIONS FTR-B4C - Through hole type l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) l Schematics (TOP VIEW) l PC board mounting pad layout (TOP VIEW) l Schematics (TOP VIEW) l PC board mounting pad layout (TOP VIEW) FTR-B4G - Surface mount type l Dimensions FTR-B4S- Space saving type l Dimensions * Indicates reset state for latching relays (FTR-B4CB, FTR-B4GB and FTR-B4SB versions) Indicates non-operate state for standard relays (FTR-B4CA, FTR-B4GA and FTR-B4SA versions) 7 FTR-K1 SERIES FTR-B4 SERIES n COIL POLARITY LATCHING TYPE Coil terminal 1 8 Set + - Reset - + n RECOMMENDED SOLDERING CONDITIONS FOR SMT (SEE PAGE 9) (TEMPERATURE PROFILE) Notes: 1. Temperature profiles on page 9 show the temperature of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces vary according to the size of PC board, status of parts mounting and heating method. n PRECAUTIONS - For details on general precautions, refer to the section on technical descriptions. - Since this is a polarized relay, follow the instructions of the internal wiring diagram for the connections of the coil. - Note that the terminal layout and internal wiring of the surface mount relay are a top view. - SMT versions of the FTR-B4 relays have moisture sensitivity level 3, acc. JEDEC-J-STD-020D - SMT versions of the FTR-B4 relays will be shipped in "dry pack". Relays have an "out of bag" storage time of 192h. n PACKAGING SPECIFICATIONS l Packaging method l Packaging orientation code: B l Tape dimensions - Packaging standard: JIS C 0806 - Taping type: TB 2412 - Reel type: R24D - Quantity of 1 reel: 500 pieces l Reel dimensions Note: Relays are sold in 500 pieces per box. Minimum order quantity is 1000 pieces for tube packing and 500 pieces for tape & reel packing. 8 FTR-K1 SERIES FTR-B4 SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Cu-Ni for FTR-B3 and FTR-B4 series relays. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu or Sn-3.0 Cu-Ni (only FTR-B3 and FTR-B4) Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 9 FTR-K1 SERIES FTR-B4 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. January 09, 2012 10