INNOLINE
DC/DC-Converter
with 3 year Warranty
R-78B-1.0
1.0 AMP
SIP3
Single Output
●Efficiency up to 97%,Non isolated,
no need for heatsinks
●Pin-out compatible with LM78XX Linears
●Low profile( L*W*H=11.5*8.5*17.5mm)
●Wide input range.(4.75V ~ 34V)
●Short circuit protection, Thermal shutdown
●Low ripple and noise
●“L” version with 90° pins
●See Innoline Application Notes for use as an
inverter (alternative to LM79xx Linear)
Features
Selection Guide
Part Input Output Output Efficiency
Number Range Voltage Current Min. Vin Max. Vin
SIP3 (V) (V) (A) (%) (%)
R-78B1.5-1.0 4.75 – 26 1.5 1.0 77 71
R-78B1.8-1.0 4.75 – 26 1.8 1.0 80 74
R-78B2.5-1.0 4.75 – 32 2.5 1.0 85 78
R-78B3.3-1.0 4.75 – 32 3.3 1.0 89 83
R-78B5.0-1.0 6.5 – 32 5.0 1.0 93 88
R-78B6.5-1.0 9.0 – 32 6.5 1.0 94 90
R-78B9.0-1.0 12 – 32 9.0 1.0 95 93
R-78B12-1.0 16 – 32 12 1.0 96 95
R-78B15-1.0 20 – 32 15 1.0 97 96
Output Power (%)
120
100
20
60
100750
-40
Operating Temperature (°C)
0
80
5025
71
Safe Operating Area
85
40
Derating-Graph
(Ambient Temperature)
The R-78Bxx-1.0 Series high efficiency switching regulators are ideally suited to replace 78xx linear regulators and are
pin compatible. The efficiency of up to 97% means that very little energy is wasted as heat so there is no need for any
heat sinks with their additional space and mounting costs.
The L-Version with 90° pins allows direct replacement for laid-flat regulators where component height is at a premium.
Low ripple and noise figures and a short circuit input current of typically only 10mA round off the specifications of this
versatile converter series.
Description
* add Suffix “L” for 90° bent pins, e.g. R-78B5.0-1.0L
EN-55022 Certified
EN-55024 Certified
EN-60601-1-2 Certified
IEC/EN-60950-1 Certified
RoHS
2011/65/EU
6/6
Refer to Application Notes
Characteristics Conditions Min. Typ. Max.
Input Voltage Range 1.5V, 1.8V 4.75V 25 26V abs. max.
2.5V to 15.5V 4.75V 32 34V abs. max.
Output Voltage Range (for customized parts) All Series 1.5V 15.5V
Output Current (see Note 1) All Series 0mA* 1000mA
Short Circuit Input Current (Vin = 24V) All Series 60mA
Internal Power Dissipation 0.65W
Short Circuit Protection Continuous, automatic recovery
Output Voltage Accuracy (At 100% Load) All Series ±2% ±3%
Line Voltage Regulation (Vin = min. to max. at full load) 1.5V to 6.5V 0.2% 0.4%
9V to 15.5V 0.1% 0.2%
Load Regulation (10% to 100% full load) 1.5V to 6.5V 0.4% 0.6%
9V to 15.5V 0.25% 0.4%
Dynamic Load Stability (with Output Capacitor=100µF) 100% <-> 50% load ±100mV ±150mV
Transient Recovery Time 1.0ms 1.5ms
Ripple & Noise (without Output Capacitor) 1.5V to 6.5V 15mVp-p 20mVp-p
(10% to 100% full load) 9V to 15.5V 25mVp-p 35mVp-p
Temperature Coefficient -40°C ~ +85°C ambient 0.015%/°C
continued on next page
Specifications (refer to the standard application circuit, Ta: 25°C, minimum load = 10%)
www.recom-power.com I-21REV: 0/2015
Efficiency (%)
50
Efficiency Vs
Vin (Full Load)
Vo=1.8V Vo=2.5V
Vo=5V
Vo=3.3V
25
Vin ( V )
10 20 34
75
100
Vo=1.5V
Vo=12V
Vo=15V
Vo=9V
Vo=6.5V
Efficiency
Ripple (mV)
50
Ripple Vs
Vin ( Full Load )
Vo=1.5V,1.8V
Vo=2.5V
Vo=5V
Vo=3.3V
25
Vin ( V )
10 20 34
Vo=9V,12V
Vo=15V
Vo=6.5V
Ripple
R-78B-1.0
Characteristics Conditions Min. Typ. Max.
Max capacitance Load with normal start-up time, no external components 470µF
with <1 second start up time + diode protection circuit 6800µF
Switching Frequency 280kHz 330kHz 380kHz
Quiescent Current Vin = min. to max. at 0% load 5mA 7mA
Input Reflected Ripple Current All Series 150mA 200mAp-p
Operating Temperature Range -40°C +85°C
Operating Case Temperature +100°C
Storage Temperature Range -55°C +125°C
Case Thermal Impedance 60°C / W
Relative Humidity 95% RH
Case Material Epoxy with Non-Conductive Plastic Case (UL94V-0)
Package Weight 4g
Packing Quantity 42 pcs per Tube
Conducted Emissions EN55022 Class B
Radiated Emissions EN55022 Class B
ESD EN61000-4-2 Class A
IEC/EN General Safety Report: SPCLVD 1407030-1 IEC/EN-60950-1, 2nd Edition
MTBF (+25°C) using MIL-HDBK 217F 6584 x 10³ hours
. (+71°C) using MIL-HDBK 217F 1139 x 10³ hours
R-78Bxx-1.0
(L) Series
Specifications (refer to the standard application circuit, Ta: 25°C, minimum load = 10%)
INNOLINE
DC/DC-Converter
}
Detailed Information see
Application Notes chapter "MTBF"
*Note: Operation under no load will not damage these devices, however they may not meet all specifications. A minimum load of 10mA is recommended
R-78Bxx-1.0
-Vout
+Vout
+Vin
-Vin
C1
22µF
(Vin>30V)
To protect the converter during power-up, use C1=22µF if Vin>30V
Typical Application Circuit
Characteristics
I-22 www.recom-power.comREV: 0/2015
R-78B-1.0
INNOLINE
DC/DC-Converter
Characteristics
Efficiency (%)
100
0.2
Efficiency Vs
Load ( Vin=Max )
Vo=1.5V
Vo=3.3V
Vo=5V
Vo=2.5V
50
Output Current ( A )
0.4 0.6 0.8 1.0 1.2
75
25
Vo=1.8V
Vo=15V
Vo=12V
Vo=6.5V
Vo=9V
Efficiency (%)
100
0.2
Efficiency Vs
Load ( Vin=Min )
Vo=1.5V
Vo=3.3V
Vo=5V
Vo=2.5V
50
Output Current ( A )
0.4 0.6 0.8 1.0 1.2
75
25
Vo=1.8V
Vo=15V
Vo=12V
Vo=9V, 6,5V
Ripple (mV)
50
0.2
Ripple Vs
Load ( Vin=Max )
Vo=1.5V, 1.8V
Vo=2.5V
Vo=5V
Vo=3.3V
25
Output Current ( A )
0.4 0.6 0.8 1.0 1.2
Vo=9V, 12V
Vo=15V
Vo=6.5V
R-78Bxx-1.0
(L) Series
Add a blocking diode to Vout if
current can flow backwards into
the output, as this can damage
the converter when it is powered
down.
The diode can either be fitted
across the device if the source is
low impedance or fitted in series
with the output (recommended).
Optional Protection Circuit
Optional Protection 1: Optional Protection 2:
R-78xx-xx
-Vout
+Vout
+Vin
-Vin
R-78xx-xx
-Vout
Vout=
+Vout -
0.3V
+Vin
-Vin
Schottky Diode
Efficiency Ripple
www.recom-power.com I-23REV: 0/2015
R-78B-1.0
2.54
2.54
Top View
Bottom View
Front View Front View
8.50
2.0
0.25
5.08
3.21
213
4.10
0.51 typ.
0.7 ±1.0
17.5
RECOM
R-78B5.0-1.0
****
Pb
1.00ø+0.15/0
11.50
RECOM
R-78B5.0-1.0
****
Pb
8.50
4.10
1.50 max
Application Examples
INNOLINE
DC/DC-Converter
Package Style and Pinning (mm)
SIP3 PIN Package
+Vin
-Vin
R-78B5.0-1.0
-12V@84mA
+12V@84mA
0V Com
C1 C2
RD-0512D
- +/-12V outputs for analogue circuits, e.g. instrumentation amplifier
- Wide input range 6.5V to 34V
C1: optional, C2: required (further
decoupling filtering may be necessary
between the two converters)
+5V@0.4A
- +5V output for digital circuits
+Vin
-Vin
R-78B5.0-1.0 +5V@1A
C1
C2
RP10-4812SEW
- Improved loading / line regulation
- Wide Input Voltage Range - 18~75V C2,C3 : optional
- Point-of-Load Architecture
- High isolation voltage - 1.6kV
R-78B3.3-1.0
0V
+3.3V@1A
C3
+12V@0.1A
- C1 is required. Further decoupling filtering
may be necessary between the converters
R-78Bxx-1.0
(L) Series
High efficiency multiple output
Isolated, wide Input range, Distributed Power Architecture (Point of Load)
Pin Connections
Pin #
1 +Vin
2 GND
3 +Vout
xx.x ±0.5mm
xx.xx ±0.25mm
Recommended Footprint Details
L - Version
I-24 www.recom-power.comREV: 0/2015
The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit
written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer
shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
RECOM:
R-78B12-1.0 R-78B3.3-1.0 R-78B5.0-1.0 R-78B6.5-1.0 R-78B1.5-1.0 R-78B1.5-1.0L R-78B1.8-1.0 R-78B1.8-1.0L
R-78B12-1.0L R-78B15-1.0 R-78B15-1.0L R-78B2.5-1.0 R-78B2.5-1.0L R-78B3.3-1.0L R-78B5.0-1.0L R-78B6.5-
1.0L R-78B9.0-1.0 R-78B9.0-1.0L