SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Members of the Texas Instruments
Widebus
Family
D
State-of-the-Art
EPIC-
ΙΙ
B
BiCMOS Design
Significantly Reduces Power Dissipation
D
Latch-Up Performance Exceeds 500 mA Per
JEDEC Standard JESD-17
D
Typical VOLP (Output Ground Bounce)
< 1 V at VCC = 5 V, TA = 25°C
D
High-Impedance State During Power Up
and Power Down
D
Distributed VCC and GND Pin Configuration
Minimizes High-Speed Switching Noise
D
Flow-Through Architecture Optimizes PCB
Layout
D
High-Drive Outputs (–32-mA IOH, 64-mA IOL)
D
Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D
Package Options Include Plastic 300-mil
Shrink Small-Outline (DL) and Thin Shrink
Small-Outline (DGG) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
description
The ’ABTH16460 are 4-bit to 1-bit multiplexed
registered transceivers used in applications
where four separate data paths must be
multiplexed onto or demultiplexed from a single
data path. Typical applications include
multiplexing and/or demultiplexing of address and
data information in microprocessor or
bus-interface applications. These devices also
are useful in memory-interleaving applications.
Five 4-bit I/O ports (1A–4A, 1B1–4, 2B1–4, 3B1–4, and 4B1–4) are available for address and/or data transfer .
The output-enable (OEB, OEB1–OEB4, and OEA) inputs control the bus-transceiver functions. These control
signals also allow 4-bit or 16-bit control, depending on the OEB level.
Copyright 1997, Texas Instruments Incorporated
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus and EPIC-ΙΙB are trademarks of Texas Instruments Incorporated.
SN54ABTH16460 . . . WD PACKAGE
SN74ABTH16460 . . . DGG OR DL PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
LEAB1
LEAB2
LEBA
GND
LEB1
LEB2
VCC
CLKBA
OEB
CLKAB
GND
1A
2A
CE_SEL0
CE_SEL1
3A
4A
GND
CLKENAB
CLKENB
CLKENBA
VCC
LEB3
LEB4
GND
OEA
LEAB3
LEAB4
OEB1
OEB2
SEL0
GND
1B1
1B2
VCC
1B3
1B4
2B1
GND
2B2
2B3
2B4
3B1
3B2
3B3
GND
3B4
4B1
4B2
VCC
4B3
4B4
GND
SEL1
OEB3
OEB4
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
description (continued)
Address and/or data information can be stored using the internal storage latches/flip-flops. The latch-enable
(LEB1–LEB4, LEBA, and LEAB1–LEAB4) and clock/clock-enable (CLK/CLKEN) inputs are used to control data
storage. When either one of the latch-enable inputs is high, the latch is transparent (clock is a don’t care as long
as the latch enable is high). When the latch-enable input goes low (providing that the clock does not transit from
low to high), the data present at the inputs is latched and remains latched until the latch-enable input is returned
high. When the clock enable is low and the corresponding latch enable is low, data can be clocked on the
low-to-high transition of the clock. When either the clock enable or the corresponding latch enable is high, the
clock is a don’t care.
Four select pins (SEL0, SEL1, CE_SEL0, and CE_SEL1) are provided to multiplex data (A port), or to select
one of four clock enables (B port). This allows the user the flexibility of controlling one bit at a time.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.
When VCC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down.
However , to ensure the high-impedance state above 2.1 V, OE should be tied to VCC through a pullup resistor;
the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54ABTH16460 is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74ABTH16460 is characterized for operation from –40°C to 85°C.
Function Tables
A-TO-B OUTPUT ENABLE†
INPUTS OUTPUT
OEB OEBn Bn
H H Z
HLZ
LHZ
L L Active
†n = 1, 2, 3, 4
A-TO-B STORAGE
(assuming OEB = L, OEBn = L)‡
INPUTS OUTPUTS
CLKENAB CE_SEL1 CE_SEL0 CLKAB LEAB1 LEAB2 LEAB3 LEAB4 B1 B2 B3 B4
X X X H or L H L L L A A0A0A0
XX X H or L H H H L A AAA
0
LX X L LLLLA
0A0A0A0
LLL↑LLLLAA0A0A0
LLH↑LLLLA
0AA
0A0
LHL↑LLLLA
0A0AA
0
LHH↑LLLLA
0A0A0A
H X X ↑L L L L A0A0A0A0
‡This table does not cover all the latch-enable cases since they have similar results.
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Function Tables (Continued)
B-TO-A STORAGE
(before point P)
INPUTS
P
CLKENB CLKBA LEB1 LEB2 LEB3 LEB4 SEL1 SEL0
P
X X H L L L L L B1
XXLHLLLHB2
XX LLHLHLB3
XXLLLHHHB4
↑
L L B1
L
↑
L
L
L
L
LHB2
L
↑
L
L
L
L
HLB3
HHB4
L L B10†
L
L
L
L
L
L
LHB2
0†
L
L
L
L
L
L
HLB3
0†
H H B40†
†Output level before the indicated steady-state input conditions were established
B-TO-A STORAGE
(after point P)
INPUTS OUTPUT
CLKENBA CLKBA LEBA OEA BA
X X X H X Z
XXHLL L
XXHLH H
HXLLXA
0†
L↑LLL L
L↑LLH H
L L L L X A0†
†Output level before the indicated steady-state input conditions
were established
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
logic diagram (positive logic)
LE
D
CLK
CE
LE
D
CLK
CE
CLK
CE
D
LE
CLK
CE
D
LE LE
CLK
CE
D
LE
CLK
CE
D
LE
CLK
CE
D
LE
CLK
CE
D
M
U
X
CE
CLK
D
LE
P
CE_SEL0
CE_SEL1
CLKENAB
1B1
1B2
1B3
1B4
CLKENAB Selector
One of Four
Channels
CLKAB
OEA
1A
OEB
OEB4
OEB3
OEB2
OEB1
CLKENBA
CLKBA
LEBA
SEL0
SEL1
CLKENB
LEB1
LEB2
LEB3
LEB4 LEAB4
LEAB3
LEAB2
LEAB1
24
23
6
5
31
54
3
8
21
10
26
12
48
49
51
52
19
15
14
9
29
30
55
56
1
2
27
28
20
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (except I/O ports) (see Note 1) –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage range applied to any output in the high or power-off state, VO –0.5 V to 5.5 V. . . . . . . . . . . . . . . . . . .
Current into any output in the low state, IO: SN54ABTH16460 96 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SN74ABTH16460 128 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input clamp current, IIK (VI < 0) –18 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output clamp current, IOK (VO < 0) –50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJA (see Note 2): DGG package 81°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL package 74°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51.
recommended operating conditions (see Note 3)
SN54ABTH16460 SN74ABTH16460
UNIT
MIN MAX MIN MAX
UNIT
VCC Supply voltage 4.5 5.5 4.5 5.5 V
VIH High-level input voltage 2 2 V
VIL Low-level input voltage 0.8 0.8 V
VIInput voltage 0 VCC 0 VCC V
IOH High-level output current –24 –32 mA
IOL Low-level output current 48 64 mA
∆t/∆vInput transition rise or fall rate Outputs enabled 10 10 ns/V
∆t/∆VCC Power-up ramp rate 200 200 µs/V
TAOperating free-air temperature –55 125 –40 85 °C
NOTE 3: Unused control pins must be held high or low to prevent them from floating.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA = 25°C SN54ABTH16460 SN74ABTH16460
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYP†MAX MIN MAX MIN MAX
UNIT
VIK VCC = 4.5 V, II = –18 mA –1.2 –1.2 –1.2 V
VCC = 4.5 V, IOH = –3 mA 2.5 2.5 2.5
VOH
VCC = 5 V, IOH = –3 mA 3 3 3
V
V
OH
VCC =45V
IOH = –24 mA 2 2
V
V
CC =
4
.
5
V
IOH = –32 mA 2* 2
VOL
VCC =45V
IOL = 48 mA 0.36 0.5
V
V
OL
V
CC =
4
.
5
V
IOL = 64 mA 0.55* 0.55
V
Vhys 100 mV
II
Control
inputs VCC = 0 to 5.5 V,
VI = VCC or GND ±1±1±1
µA
I
IA or B ports VCC = 2.1 V to 5.5 V,
VI = VCC or GND ±20 ±20 ±20 µ
A
II(h ld)
AorB
p
orts
VCC =45V
VI = 0.8 V 75 500 75 500 75 500
µA
I
I(hold)
A
or
B
ports
V
CC =
4
.
5
V
VI = 2 V –75 –500 –75 –500 –75 –500 µ
A
IOZPU‡VCC = 0 to 2.1 V,
VO = 0.5 V to 2.7 V, OE = X ±50 ±50 ±50 µA
IOZPD‡VCC = 2.1 V to 0,
VO = 0.5 V to 2.7 V, OE = X ±50 ±50 ±50 µA
Ioff VCC = 0, VI or VO ≤ 4.5 V ±100 ±100 µA
ICEX VCC = 5.5 V,
VO = 5.5 V Outputs high 50 50 50 µA
IO§VCC = 5.5 V, VO = 2.5 V –50 –100 –200 –50 –200 –50 –200 mA
Outputs high 1.5 1.5 1.5
ICC
VCC = 5.5 V,
IO0
A outputs low 10 10 10
mA
I
CC
I
O =
0
,
V
I
= V
CC
or
G
ND B outputs low 32 32 32
mA
VI
=
VCC
or
GND
Outputs disabled 1.5 1.5 1.5
∆ICC¶VCC = 5.5 V, One input at 3.4 V,
Other inputs at VCC or GND 1.5 1.5 1.5 mA
CiControl
inputs VI = 2.5 V or 0.5 V 8 pF
Cio A or B ports VO = 2.5 V or 0.5 V 3.5 pF
* On products compliant to MIL-PRF-38535, this parameter does not apply.
†All typical values are at VCC = 5 V.
‡This parameter is characterized but not production tested.
§Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
¶This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
timing requirements over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
SN54ABTH16460 SN74ABTH16460
UNIT
MIN MAX MIN MAX
UNIT
fclock Clock frequency 0 160 0 160 MHz
CLKAB high or low 3.8 3.8
CLKBA high or low 4.5 4.5
twPulse duration LEAB1, 2, 3, or 4 high 2.2 2.2 ns
LEBA high 2.1 2.1
LEB1, 2, 3, or 4 high 2.4 2.4
↑
A bus 2.5 2.5
Before CLKAB
↑
CE_SEL0/1 3.2 3.2
CLKENAB 3.2 3.2
Before LEAB1, 2, 3, or 4↓A bus 3.6 3.6
↑
B bus 3.8 3.8
↑
CLKENB 2.3 2.3
tsu Setup time Before CLKBA
↑
CLKENBA 2.5 2.5 ns
LEB1, 2, 3, or 4 4.3 4.3
SEL0/1 4.5 4.5
Before LEB1, 2, 3, or 4↓B bus 3.2 3.2
↓
B bus 4 4
Before LEBA
↓
LEB1, 2, 3, or 4 4.4 4.4
SEL0/1 4.3 4.3
↑
A bus 0.5 0.5
After CLKAB
↑
CE_SEL0/1 1.1 1.1
CLKENAB 0.5 0.5
After LEAB1, 2, 3, or 4↓A bus 1.2 1.2
↑
B bus 1.3 1.3
thHold time
After CLKBA↑
CLKENB 1 1 ns
After
CLKBA↑
CLKENBA 1 1
SEL0/1 0 0
After LEB1, 2, 3, or 4↓B bus 1.5 1.5
After LEBA↓
B bus 0.4 0.4
After
LEBA↓
SEL0/1 0.1 0.1
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 50 pF (unless otherwise noted) (see Figure 1)
PARAMETER FROM
(INPUT)
TO
(OUTPUT)
VCC = 5 V,
TA = 25°CSN54ABTH16460 SN74ABTH16460 UNIT
(INPUT)
(OUTPUT)
MIN TYP MAX MIN MAX MIN MAX
fmax 160 160 160 MHz
tPLH
B
A
2.5 3.6 5.9 2.5 7.1 2.5 6.5
ns
tPHL
B
A
2 3.5 5.8 2 6.8 2 6.5
ns
tPZH
OEA
A
1.5 2.8 4.8 1.5 5.9 1.5 5.6
ns
tPZL
OEA
A
1.5 2.6 4.6 1.5 5.5 1.5 5.2
ns
tPHZ
OEA
A
2.5 3.8 5.3 2.5 6 2.5 5.9
ns
tPLZ
OEA
A
1.5 4.6 6.1 1.5 7 1.5 6.5
ns
tPLH
A
B
2 3.2 5.2 2 6.2 2 5.7
ns
tPHL
A
B
1.5 3.1 5.2 1.5 6.1 1.5 5.7
ns
tPZH
OEB
B
1.5 3.3 5.7 1.5 6.7 1.5 6.4
ns
tPZL
OEB
B
1.5 3.2 5.5 1.5 6.6 1.5 6.3
ns
tPHZ
OEB
B
3 4.7 6.3 3 7.1 3 7
ns
tPLZ
OEB
B
2 4 5.5 2 6.6 2 6.1
ns
tPZH
OEB1 2 3 4
B
1.5 3 5.2 1.5 6 1.5 5.8
ns
tPZL
OEB1
,
2
,
3
,
4
B
1.5 2.9 4.9 1.5 5.9 1.5 5.6
ns
tPHZ
OEB1 2 3 4
B
2.5 4 5.7 2.5 6.2 2.5 6.1
ns
tPLZ
OEB1
,
2
,
3
,
4
B
1.5 3.5 4.8 1.5 5.8 1.5 5.3
ns
tPLH
CLKBA
A
1.5 4.2 6.7 1.5 8.1 1.5 7.4
ns
tPHL
CLKBA
A
1.5 4.4 6.9 1.5 8.4 1.5 7.7
ns
tPLH
CLKAB
B
2 3.4 5.6 2 6.8 2 6.2
ns
tPHL
CLKAB
B
2 3.4 5.3 2 6.3 2 5.9
ns
tPLH
LEBA
A
2 3 5 2 6.1 2 5.6
ns
tPHL
LEBA
A
2 3.1 4.8 2 5.8 2 5.3
ns
tPLH
LEAB1234
B
2 3.2 5.2 2 6.3 2 5.8
ns
tPHL
LEAB1
,
2
,
3
,
4
B
2 3.3 5 2 6.1 2 5.6
ns
tPLH
LEBA1234
A
2.5 4 6.5 2.5 7.8 2.5 7.2
ns
tPHL
LEBA1
,
2
,
3
,
4
A
2.5 4 6.1 2.5 7.5 2.5 6.8
ns
tPLH
SEL
A
2 4.1 6.7 2 8.1 2 7.5
ns
tPHL
SEL
A
2 3.8 6.2 2 7.3 2 6.9
ns
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
SN54ABTH16460, SN74ABTH16460
4-TO-1 MULTIPLEXED/DEMULTIPLEXED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS207F – OCTOBER 1992 – REVISED MAY 1997
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
1.5 V
th
tsu
From Output
Under Test
CL = 50 pF
(see Note A)
LOAD CIRCUIT
S1
7 V
Open
GND
500 Ω
500 Ω
Data Input
Timing Input 1.5 V 3 V
0 V
1.5 V 1.5 V
3 V
0 V
3 V
0 V
1.5 V
tw
Input
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOLTAGE WAVEFORMS
PULSE DURATION
tPLH
tPHL
tPHL
tPLH
VOH
VOH
VOL
VOL
1.5 V 1.5 V 3 V
0 V
1.5 V1.5 V
Input
1.5 V
Output
Control
Output
W aveform 1
S1 at 7 V
(see Note B)
Output
W aveform 2
S1 at Open
(see Note B)
VOL
VOH
tPZL
tPZH
tPLZ
tPHZ
1.5 V1.5 V
3.5 V
0 V
1.5 V VOL + 0.3 V
1.5 V VOH – 0.3 V
≈ 0 V
3 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
Output
Output
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7 V
Open
TEST S1
NOTES: A. CL includes probe and jig capacitance.
B. W aveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
W aveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf≤ 2.5 ns.
D. The outputs are measured one at a time with one transition per measurement.
1.5 V
Figure 1. Load Circuit and Voltage Waveforms
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
SN74ABTH16460DGGR TSSOP DGG 56 2000 330.0 24.4 8.6 15.6 1.8 12.0 24.0 Q1
SN74ABTH16460DLR SSOP DL 56 1000 330.0 32.4 11.35 18.67 3.1 16.0 32.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2008
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74ABTH16460DGGR TSSOP DGG 56 2000 346.0 346.0 41.0
SN74ABTH16460DLR SSOP DL 56 1000 346.0 346.0 49.0
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2008
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/videoWireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2008, Texas Instruments Incorporated
