A5929 Automotive Full-Bridge MOSFET Driver FEATURES AND BENEFITS DESCRIPTION * High current Full-Bridge gate drive for n-channel MOSFETs * Cross-conduction protection * 5.5 V to 50 V Supply Voltage Range * Motor phase short to supply and short to ground detection * Undervoltage, overtemperature monitors * Low Current Sleep Mode The A5929 is a full-bridge controller for use with n-channel external power MOSFETs and is specifically designed for automotive applications. A unique charge pump regulator provides full (>10 V) gate drive at battery voltages down to 7 V and allows the A5929 to operate with reduced gate drive at battery voltages down to 5.5 V. A bootstrap capacitor is used to provide the above battery supply voltage required for n-channel MOSFETs. One logic level input is provided for each of the four power MOSFETs in the full-bridge, allowing motors to be driven with any PWM scheme defined by an external controller. The power MOSFETs are protected from cross-conduction by integrated crossover control. PACKAGE: 24-Pin eTSSOP with exposed thermal pad (suffix LP) Motor phase short-to-supply and short-to-ground detection is provided by independent drain-source voltage monitors on each MOSFET. Short faults, supply undervoltage, and chip over-temperature conditions are indicated by a single open drain fault output. The A5929 is supplied in a 24-pin TSSOP power package with an exposed thermal pad (package type LP). This package is available in lead (Pb) free versions, with 100% matte-tin lead frame plating (suffix -T). Not to scale VBAT VDD A5929 MCU Typical Application Diagram A5929-DS A5929 Automotive Full-Bridge MOSFET Driver SPECIFICATIONS Selection Guide Part Number Packing Package A5929KLPTR-T 4000 pieces per reel 9.7mm x 4.4mm, 1.2mm nominal height 24 lead TSSOP with exposed thermal pad Absolute Maximum Ratings 1 Characteristic Load Supply Voltage Symbol Notes VBB Rating Unit -0.3 to 50 V Terminal VREG -0.3 to 16 V Terminals CP1, CP2 -0.3 to 16 V Logic Inputs AHI, ALO, BHI, BLO, and ENAB -0.3 to 6.5 V Terminal VBRG -5 to 55 V Terminal LSS -4 to 6.5 V Terminals SA, SB -5 to 55 V Terminals GHA, GHB Sx to Sx+15 V Terminals GLA, GLB -5 to 16 V -0.3 to Sx+15 V Terminal FAULT -0.3 to 6.5 V Terminal VDSTH -0.3 to 6.5 V TA -40 to 150 C TJ(max) 165 C 175 C -55 to 150 C Test Conditions Value Unit 4-layer PCB based on JEDEC standard 28 C/W 38 C/W 2 C/W Terminals CA, CB Ambient Operating Temperature Range 2 Maximum continuous junction temperature Transient Junction Temperature TtJ Storage Temperature Range Tstg 1 With Over temperature event not exceeding 10s, lifetime duration not exceeding 10hours, determined by design characterisation. respect to GND. by power dissipation. 2 Limited Thermal Characteristics 3 may require derating at maximum conditions Characteristic Package Thermal Resistance Symbol RJA RJP 3Additional 2-layer PCB with 3.8 in2 Copper each side thermal information available on the Allegro website. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 2 A5929 Automotive Full-Bridge MOSFET Driver LSS 1 24 BLO NC 2 23 BHI GLB 3 22 ALO GHB 4 21 AHI SB 5 20 FAULT CB 6 19 VDSTH PAD GLA 7 18 ENAB GHA 8 17 GND SA 9 16 VBRG CA 10 15 VBB NC 11 14 CP1 VREG 12 13 CP2 Package LP, 24-Pin eTSSOP Pin-out Diagram Terminal List Table Number Name Number Name 1 LSS Common Low-side Source Function 13 CP2 Pump Capacitor Function 2 NC No connect 14 CP1 Pump Capacitor 3 GLB Phase B Low-side Gate Drive 15 VBB Main Power Supply 4 GHB Phase B High-side Gate Drive 16 VBRG High-side Drain voltage sense 5 SB Phase B Motor Connection 17 GND Ground 6 CB Phase B Bootstrap Capacitor 18 ENAB Enable Input 7 GLA Phase A Low-side Gate Drive 19 VDSTH VDS Monitor Threshold Voltage 8 GHA Phase A High-side Gate Drive 20 FAULT Diagnostic output 9 SA Phase A Motor Connection 21 AHI Phase A HS control 10 CA Phase A Bootstrap Capacitor 22 ALO Phase A LS control 11 NC No connect 23 BHI Phase B HS control 12 VREG Gate Drive Supply Output 24 BLO Phase B LS control - PAD Exposed thermal pad-Connect to GND Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 3 A5929 Automotive Full-Bridge MOSFET Driver Battery + CP VBB CP2 CP1 VBAT Charge Pump Regulator VREG Logic Supply Regulator VBRG ENAB CA CBOOTA AHI GHA HS Drive VDS Monitor RGHA RGHB RGLA RGLB SA VREG ALO VDS Monitor LS Drive Control Logic GLA Phase A LSS As Above for Phase B BHI CB GHB CBOOTB SB BLO GLB FAULT VDSTH Diagnostics & Protection PAD GND Functional Block Diagram Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 4 A5929 Automotive Full-Bridge MOSFET Driver ELECTRICAL CHARACTERISTICS: valid at TJ = -40 to +150C, VBB = 7 to 50 V; unless otherwise specified Characteristic Symbol Test Conditions Min. Typ. Max. Unit Supply & Reference VBB Functional Operating Range 2 VBB Quiescent Current Correct Function Parameters not Guaranteed 5.5 - 50 V IBBQ Operational Mode, Outputs Low VBB = 12 V - 6 14 mA IBBS Sleep Mode, VBB = 12 V, ENAB < 0.6 V - - 10 A 12.5 13 13.75 V 7.5 V < VBB 9 V, IREG = 0 mA to 10 mA 12.0 13 13.75 V 6 V < VBB 7.5 V, IREG = 0 mA to 9 mA 2xVBB-3.0 - - V VBB > 9 V, IREG = 0 mA to 15 mA VREG Output Voltage Bootstrap Diode Forward Voltage Bootstrap Diode Resistance Bootstrap Diode Current Limit VREG VfBOOT rD 5.5 V < VBB 6 V, IREG < 8 mA 8.5 9.5 - V ID = 10 mA 0.4 0.7 1.0 V ID = 100 mA 1.5 2.2 3.1 V 6 13 28 250 500 750 mA rD(100 mA) = (VfBOOT(150 mA) - VfBOOT(50 mA))/ 100 mA IDBOOT Disable Time tSLT From ENAB < VIL to Gxx low 200 ns Sleep Mode Activation Timeout tSLT From ENAB < VIL 7.5 10 12.5 ms Wake Up from Sleep Delay tWK ENAB > VIH. CREG < 1 F - - 1 ms Turn-on Time tr CLOAD = 1 nF, 20% to 80% - 35 - ns Turn-off Time tf CLOAD = 1 nF, 80% to 20% - 20 - ns TJ = 25C, IGHx = -150 mA 5 8 13 TJ = 150C, IGHx = -150 mA 10 15 24 TJ = 25C, IGLx = 150 mA 1.5 2.4 4.6 TJ = 150C, IGLx = 150 mA 2.5 4 6.5 Gate Output Drive Pull-up On Resistance RDS(on)UP Pull-down On Resistance RDS(on)DN GHx Output Voltage High VGHH VCx -0.2 - - V GHx Output Voltage Low VGHL - - VSX+0.3 V GLx Output Voltage High VGLH VREG-0.2 - - V GLx Output Voltage Low VGLL - - VLSS+0.3 V GHx Passive Pull-down RGHPD VGHx - VSx < 0.3 V - 400 - k GLx Passive Pull-down RGLPD VGLx - VLSS < 0.3 V - 400 - k Bootstrap Capacitor fully charged Turn-off Propagation Delay 3 tP(off) Input change to unloaded Gate output change 60 90 180 ns Turn-on Propagation Delay 3 tP(on) Input change to unloaded Gate output change 60 90 180 ns Prop Delay Matching - Phase to Phase DtPP Same phase change - 10 - ns Prop Delay Matching - On to Off DtOO Single phase - 30 - ns Continued on the next page... Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 5 A5929 Automotive Full-Bridge MOSFET Driver ELECTRICAL CHARACTERISTICS (continued): valid at TJ = -40 to +150C, VBB = 7 to 50 V; unless otherwise specified Characteristic Symbol Test Conditions Min. Typ. Max. Unit Logic Inputs & Outputs Input Low Voltage (xHI, xLO) VIL - - 0.8 V Input High Voltage (xHI, xLO) VIH 2.0 - - V Input Low Voltage (ENAB) VIL - - 0.8 V Input Low Voltage (ENAB) VIL - - 0.6 V Input High Voltage (ENAB) Minimum power sleep mode VIH 2.0 - - V Input Hysteresis (xHI, xLO) (ENAB) VIhys 100 300 - mV Input Pull-down Resistor (xHI, xLO) RPD - 50 - k Input Pulse Filter Time (xHI,xLO) tPIN - 35 - ns VDS Disable Voltage VDSD - - 100 mV Fault Disable Voltage VFLTD Output Low Voltage (FAULT) VOL Output Leakage (FAULT)1 IO - - 0.5 V IOL = 1 mA. No Fault indicated - 0.2 0.4 V 0 V < VO < 5.5 V, Fault indicated -1 - 1 A Protection VREGON VREG rising 7.5 8 8.5 V VREGOFF VREG falling 6.75 7.25 7.75 V Bootstrap Undervoltage VBOOTUV VBOOT falling, VCx - VSx 62 - 75 %VREG Bootstrap Undervoltage Hysteresis VBOOTHys - 9 - %VREG 1.1 1.2 1.3 V 0.2 - 2 V -3 - 3 A VBB-1 VBB VBB+1 V - - 250 A VDSTH 1 V - 100 - VDSTH < 1 V -150 50 +150 VDSTH 1 V - 100 - VDSTH <1V -150 50 +150 VREG Undervoltage Lockout VDS Threshold Internal VDSTHI VDS Threshold Range VDSTH VDS Threshold Input Leakage VDSTHL VBRG Input Voltage VBRG VBRG Input Current IVBRG Short-to-Ground Threshold Offset VSTGO Short-to-Battery Threshold Offset VSTBO VDSTH > 2.7 V 0 V < VDSTH < 5.5 V VDSTH = 2 V, VBB = 12 V; 0 V < VBRG < VBB mV mV VDS Fault Blank Time tBL 1.5 2.3 4.5 s Over-temperature Warning TJF Temperature increasing 170 - 180 C TJHyst Recovery = TJF - TJHyst - 15 - C Over-temperature Hysteresis 1 For input and output current specifications, negative current is defined as coming out of (sourced by) the specified device terminal. 2 Function is correct but parameters are not guaranteed below the general limits (7V). 3 See Figure 1 for gate drive output timing. xH xL tP(off) tP(off) tP(on) tP(on) GHx GLx Figure 1: Gate Drive Timing Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 6 A5929 Automotive Full-Bridge MOSFET Driver FUNCTIONAL DESCRIPTION The A5929 provides four high current gate drives capable of driving a wide range of n-channel power MOSFETs. The gate drives are configured as two high-side and two low-side drives. The four gate drives are controlled by individual TTL-threshold logic inputs which may be driven from 3.3 V or 5 V logic outputs. CA, CB The A5929 provides all necessary circuitry to ensure that the gate-source turn-on voltages of both high-side and low-side external MOSFETs are driven above 10 V at supply voltages down to 7 V. For extreme low battery voltage conditions, correct functional operation is maintained down to 5.5 V but with a reduced gate drive. High-side, gate-drive outputs for external n channel MOSFETs. The control inputs to the A5929 provide a simple solution for many motor drive applications controlled by an external microcontroller or DSP. Phase commutation and PWM control must be managed by the external system controller. Specific device functions are described more fully in the following sections. Input & Output Terminal Functions VBB Power supply for all device functions including internal logic and Charge Pump. System power should be connected to VBB through a reverse voltage protection circuit. The VBB pin should be decoupled to ground with ceramic capacitors mounted physically close to the device pins. CP1, CP2 Pump capacitor connection for charge pump. Connect a minimum 220nF, typically 470nF, between CP1 and CP2. VREG Regulated voltage, nominally 13 V, used to supply the low side gate drivers and to charge the bootstrap capacitors. A sufficiently large storage capacitor must be connected to this terminal to provide the transient charging current. GND Analogue reference, Digital and power ground. Connect to supply ground - see layout recommendations. High-side connections for the bootstrap capacitors and positive supply for high-side gate drivers. GHA, GHB SA, SB Load phase connections. Used to sense the voltages switched across the load. Also connected to the negative side of the bootstrap capacitors and constitute the negative supply connections for the floating high-side drivers. GLA, GLB Low-side, gate-drive outputs for external n-channel MOSFETs. LSS Low-side return path for discharge of the capacitance on the MOSFET gates, connected to the common sources of the lowside external MOSFETs through a low impedance track. VBRG Sense input to the top of the external MOSFET bridge. Allows accurate measurement of the voltage at the drains of the high side MOSFETs. AHI, BHI Input to control the high-side gate drives. A logic high commands the relevant high-side gate drive to be activated. ALO, BLO Input to control the low-side gate drives. A logic high commands the relevant low-side gate drive to be activated. ENAB Enable input to control all outputs and sleep mode. A logic high enables the outputs to be active. A logic low immediately disables all gate drive outputs and causes the A5929 to enter sleep mode after the Sleep Mode Activation Timeout. FAULT Open drain active-high fault output. If a fault is present the open- Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 7 A5929 Automotive Full-Bridge MOSFET Driver drain pull-down is off and the FAULT input may be pulled high by an external pull-up resistor connected to any voltage up to a maximum of 5.5 V. regulated supply is maintained by a charge pump boost converter which requires a pump capacitor, typically 470 nF, connected between the CP1 and CP2 terminals. VDSTH The regulated voltage, nominally 13 V, is available on the VREG terminal. A sufficiently large storage capacitor (See applications section) must be connected to this terminal to provide the transient charging current to the low side drivers and the bootstrap capacitors. Drain source fault threshold programming pin. The VDS fault threshold may be set by applying an externally generated analogue voltage. VDS fault reporting is disabled if VDSTH is driven to less than VDSD (e.g. shorted to ground). The VDS fault threshold is set to an internally hardwired value, VDSTHI, if VDSTH is driven to a voltage above its specified analogue input range (e.g. pulled up to the system logic supply voltage). Power Supplies A single supply voltage (VBB) applied to the VBB terminal powers all device functions including on-chip logic, analogue circuitry, and output drivers. It should be connected to the positive supply through a reverse voltage protection circuit and decoupled by a ceramic capacitor mounted close to the VBB and GND terminals. The A5929 will operate within specified performance limits with VBB between 7V to 50V and will function correctly with VBB as low as 5.5V. Sleep Mode A low power `sleep' mode is activated when a logic low is applied to the ENAB input for a period equal to the Sleep Mode Activation Timeout (tSLT). As soon as ENAB is low all gate drive outputs will be switched off. Once in sleep mode all outputs are switched to a high impedance state. Operating mode is active within a period equal to the Wake Up from Sleep Delay (tWK) from a logic high being detected on the ENAB input. It is recommended that all xLO inputs are simultaneously driven to logic high (GLx turned on) when waking from sleep in order to recharge the bootstrap capacitors and enable subsequent high side turn on. CP1,CP2, VREG The gate drivers are powered by an internal regulator which limits the supply to the drivers and therefore the maximum gate voltage. For VBB supply greater than approximately 16V the regulator operates in a linear regulator mode. Below 16V the Gate Drives The A5929 is designed to drive external, low on-resistance, power n channel MOSFETs. It will supply the large transient currents necessary to quickly charge and discharge the external MOSFET gate capacitances in order to reduce dissipation in the external MOSFET during switching. Charge current for the lowside drives is provided directly by the capacitor on the VREG terminal. Charge current for the high-side drives is delivered via the bootstrap capacitors connected, one per phase, across the Cx, Sx terminal pairs. Charge and discharge rate can be controlled by incorporating an external resistor in series with each MOSFET gate drive (GHx, GLx). High-side Gate Drive. GHA/GHB High-side, gate-drive outputs for external n channel MOSFETs. An external resistor between the GHx gate drive output and the MOSFET gate terminal (mounted as close to the latter as possible) may be used to control the slew rate at the gate, thereby controlling the di/dt and dv/dt of the voltage at the Sx terminals. GHx "high" turns on the upper half of the driver, sourcing current to the gate of the high-side MOSFET in the external motordriving bridge, turning it on. GHx "low" turns on the lower half of the driver, sinking current from the external MOSFET's gate circuit to the respective Sx terminal, turning it off. Bootstrap Charge Management Bootstrap capacitors are charged to approximately VREG when the associated Sx terminal is driven low. When the Sx terminal subsequently swings high, the capacitor provides the necessary voltage for high-side n-channel power MOSFET turn-on. At system start up it is necessary to turn on each low side drive (GLx) prior to attempting to turn on the complementary high side (GHx) in order to charge the bootstrap capacitors. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 8 A5929 Automotive Full-Bridge MOSFET Driver Low-side Gate Drive. GLA/GLB The low-side, gate-drive outputs on GLA and GLB are referenced to the LSS terminal. These outputs are designed to drive external n-channel power MOSFETs. An external resistor between the GLx gate drive output and the MOSFET gate terminal (mounted as close to the latter as possible) may be used to control the slew rate at the gate, thereby providing some control of the di/dt and dv/dt of the voltage at the Sx terminals. GLx "high" turns on the upper half of the driver, sourcing current to the gate of the lowside MOSFET in the external motor-driving bridge, turning it on. GLx "low" turns on the lower half of the driver, sinking current from the external MOSFET's gate circuit to the to the LSS terminal, turning it off. 5.5 V Internal 1 Threshold set to internal value (VDSTHI) with accuracy specified in Electrical Characteristics table. 2.7 V Intermediate 2 Drain Source Voltage Monitor The VDS fault threshold is set by applying a control voltage on the VDSTH pin as detailed in Figure 2. If a voltage between 0.2 V and 2.0 V is applied the threshold will follow this level subject to the Short to Ground Threshold (VSTGO) and Short to Battery Threshold (VSTBO) Offsets detailed in the Electrical Characteristics table. 2.3 V External Threshold set to voltage approx. equal to that applied on VDSTH pin. Accuracy not specified. VDSTH(max) 2.0 V If a voltage between 2.0 V and 2.3 V is applied the threshold will approximate the applied level but accuracy is not specified. External Threshold set to voltage applied on VDSTH pin with accuracy specified in Electrical Characteristics table. If the VDSTH pin is driven below the VDS Disable Voltage (VDSD) of 0.1 V (e.g. shorted to ground) VDS fault reporting is disabled. If the VDSTH pin is taken above 2.7 V (e.g. pulled up to the system logic supply voltage) the threshold is set to the VDS Threshold Internal (VDSTH) voltage detailed in the Electrical Characteristics table (typically 1.2 V). The VDSTH pin presents a high impedance at all voltages across its permissible input range (per the VDS Threshold Input Leakage limits detailed in the Electrical Characteristics table, VDSTHL) allowing a wide range of programming circuits to be used including simple resistive dividers. The VDSTH input has an internal passive first-order filter with a time constant of approximately 10 s. Additional filter capacitance may be added externally if required. 0.2 V VDSTH(min) Intermediate 2 VDSD 0.1 V Disable 0V 1 2 VDSTH pin typically tied to system logic supply voltage. Behaviour indeterminate due to threshold detection uncertainty. Figure 2: VDSTH Pin Voltage versus VDS Monitor Function Logic Control Inputs A set of discrete digital inputs (xHI, xLO) provides direct control of the four gate drive outputs (GHx, GLx). TTL input threshold levels ensure these can be driven from 3.3 V or 5 V logic systems. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 9 A5929 Automotive Full-Bridge MOSFET Driver Setting a logic input high causes the corresponding gate drive output to swing high thereby commanding the associated external MOSFET to turn on. Conversely, setting a logic input low swings the corresponding gate drive low commanding the MOSFET off. Table 2: Fault Definitions FAULT Fault Description Outputs Disabled Fault Latched Low No Fault No - Internal lock-out logic ensures that the high-side output drive and low-side output drive cannot be active simultaneously as detailed in Table 1. High Overtemperature No No High VREG undervoltage Yes1 No High VDS overvoltage No No Table 1: Phase Control Truth Table High Bootstrap undervoltage Yes2 Yes Input Output 1 All Comments ENAB xHI xLO GHx GLx Sx 1 0 0 L L Z Phase disabled 1 0 1 L H LO Low-side active 1 1 0 H L HI High-side active 1 1 1 L L Z Phase disabled 0 X X L L Z All disabled 0 X X Z Z Z Sleep Mode HI high-side MOSFET active, LO low-side MOSFET active X don't care, Z high impedance, both MOSFETs off An additional enable input, ENAB, may be used to turn all outputs off. ENAB must be high for the outputs to be active. When ENAB is held low for longer than the Sleep Mode Activation Time (tSLT) then the A5929 will enter sleep mode. Diagnostics Several diagnostic features are integrated into the A5929 to provide indication of fault conditions. In addition to system wide faults such as under voltage and over temperature, the A5929 integrates individual monitors for each bootstrap capacitor voltage and each exeternal MOSFET drain-source voltage. The presence of a fault condition is indicated on the FAULT pin. This is an open drain output that should be pulled to any voltage up to 5.5 V by an external resistor, typically 10 k to 47 k. The definition of the individual fault states and the effect on the gate drive outputs (GHx, GLx) are shown in Table 2 and described below. gate drives low (external MOSFETs off). side drive of phase generating FAULT condition set low (external MOSFET off). Other outputs unaffected. 2 High Fault States It is recommended that any external control circuitry remaining active in the event of a fault state being flagged is configured to take appropriate action to prevent damage to the A5929 and associated motor drive components. Overtemperature. If junction temperature exceeds the overtemperature warning threshold (TJF) the A5929 enters the overtemperature warning state and FAULT goes high. The over-temperature warning state is cleared and the FAULT output returned to logic low when the junction temperature drops below recovery level TJF - TJFhys. Whilst an over-temperature warning state is asserted no on-chip circuitry or functions are disabled. VREG UNDERVOLTAGE The charge pump generates VREG to provide low-side gate driver and bootstrap charge current. It is necessary to ensure that this voltage is high enough prior to enabling any of the gate drive outputs. If the voltage at the VREG pin drops below the falling VREG Undervoltage Lockout Threshold (VREGUVoff ) the A5929 enters the VREG undervoltage fault state, FAULT is set high, and all gate drive outputs (GHx, GLx) are disabled. The VREG undervoltage fault state is cleared and FAULT goes low when VREG rises above the VREG undervoltage lockout threshold (rising), VREGUVon. The VREG undervoltage monitor circuit is active during powerup and the A5929 remains in the VREG undervoltage fault state until VREG is greater than the rising VREG undervoltage lockout threshold, VREGUVon. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 10 A5929 Automotive Full-Bridge MOSFET Driver VDS OVERVOLTAGE When a gate drive output is commanded to turn on (GHx or GLx high) the the drain-source voltage of the corresponding external MOSFET is monitored between VBRG and Sx or Sx and LSS as appropriate. If the measured voltage exceeds the threshold value programmed on the VDSTH pin the FAULT output is set high but none of the gate drive outputs is disabled. Propagation of any fault states to the FAULT output is disabled for the VDS Fault Blank Time (tBL) at every external MOSFET turn-on event to avoid reporting spurious faults in response to switching transients. If a fault is reported on the FAULT pin it will be cleared as soon as the measured drain-source voltage drops below the programmed VDSTH level. BOOTSTRAP CAPACITOR UNDERVOLTAGE Each bootstrap capacitor is monitored to ensure sufficient highside gate drive voltage is available to initiate and maintain external MOSFET turn-on . High-side gate drive outputs only turn on if the relevant bootstrap capacitor voltage is higher than the bootstrap turn-on voltage threshold, VBOOTUV + VBOOTHys. If the bootstrap voltage is below this threshold when turn on is command on xHI the corresponding gate drive, GHx, is not switched on and FAULT is set high. The output remains off and FAULT remains high until either the affected gate drive is commanded to turn off or the FAULT pin is pulled low by external means (see FAULT pin disable description below). After a high side gate drive has been successfully turned on the appropriate bootstrap capacitor voltage must remain above the Bootstrap Undervoltage threshold (VBOOTUV). If the bootstrap capacitor voltage drops below VBOOTUV the high side driver in question is switched off and FAULT goes high. The driver will remain off and FAULT will remain high until either the affected high-side gate drive turn on commanded is removed from xHI or the FAULT pin is pulled low by external means (see FAULT pin disable description below). If a bootstrap capacitor fault condition is detected only the driver in question is disabled. All other gate drives continue to respond to control inputs on xHI, xLO. If the FAULT pin is held low (below the Fault Disable Voltage (VFLTD) by external means the bootstrap undervoltage monitor feature is disabled. In this condition, if bootstrap capacitor voltage fails to reach VBOOTUV + VBOOTHys for turn on or drops below VBOOTUV after turn on the driver in question is not forced into the off state. As the FAULT pin is held low, a fault state is not flagged. Whilst the FAULT pin is held low to disable the bootstrap undervoltage monitor any other fault conditions that might arise are undetectable outside the A5929. However, internal fault actions are unaffected and gate drive outputs are still disabled in response to other faults in accordance with Table 2. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 11 A5929 Automotive Full-Bridge MOSFET Driver APPLICATIONS INFORMATION Power Bridge Management Using PWM Control The A5929 provides individual high-side and low-side controls for each phase through the four digital control inputs. The only restriction imposed by the A5929 is to prevent the high-side and low-side gate drive from a single phase being on at the same time to avoid cross-conduction. This allows all H bridge control schemes to be implemented. This includes fast and slow decay, synchronous rectification and diode rectification, and edge aligned and centre aligned PWM. Figure 3(A) shows an example of the path of the bridge and load current. In this example the high-side MOSFETs are switched off during the current decay time (PWM-off time) and load current recirculates through the low-side MOSFETs. This is commonly referred to as high side chopping or high side PWM. During the PWM off-time the complementary MOSFETs are turned on to short the body diode and provide synchronous rectification. Figure 3(A) only shows current in one direction but the same principal applies to current in the opposite direction. The same principal also applies when the low-side MOSFETs are turned off during the PWM off-time and the load current recirculates through the high side MOSFETs as in figure 3(B). In this control scheme the microcontroller has full control over the current decay method, load current recirculation paths, braking and coasting. The A5929 provides exceptional propagation delay matching from logic input to gate drive output for high performance motor control applications. These advanced applications usually require high-resolution PWM control on each phase. This must be provided by an external controller, which must also provide the necessary dead time to avoid shoot through in the power bridge. Bootstrap Capacitor Selection CBOOT must be correctly selected to ensure proper operation of the device. Too large and time will be wasted charging the capacitor resulting in a limit on the maximum duty cycle and PWM frequency. Too small and there can be a large voltage drop at the time the charge is transferred from CBOOT to the MOSFET gate. To keep the voltage drop, due to charge sharing, small, the charge in the bootstrap capacitor (QBOOT) should be much larger than QGATE. A B Drive Phase A 1 xH 0 xL H GHx L GLx Recirculate Phase A 0 xH 1 xL L GHx H GLx B 0 1 L H B 0 1 L H (A) High-side PWM with slow decay and synchronous rectification. A B Drive Phase A 1 xH 0 xL H GHx L GLx Recirculate Phase A 1 xH 0 xL H GHx L GLx B 0 1 L H B 1 0 H L (B) Low-side PWM with slow decay and synchronous rectification. Figure 3: Power Bridge Control The charge required by the gate: QBOOT >> QGATE A factor of 20 is a reasonable value. QBOOT = CBOOT x VBOOT = QGATE x 20 CBOOT = QGATE x 20 VBOOT where VBOOT is the voltage across the bootstrap capacitor. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 12 A5929 Automotive Full-Bridge MOSFET Driver The voltage drop, V, across the bootstrap capacitor as the MOSFET is being turned on can be approximated by: QGATE V = CBOOT so for a factor of 20, V will be 5% of VBOOT. The maximum voltage across the bootstrap capacitor under normal operating conditions is VREG max. However in some circumstances the voltage may transiently reach 18 V, the clamp voltage of the Zener diode between the Cx terminal and the Sx terminal. In most applications with a good ceramic capacitor the working voltage can be limited to 16 V. Bootstrap Charging It is good practice to ensure the high side bootstrap capacitor is completely charged before a high side PWM cycle is requested. The time required to charge the capacitor (tCHARGE) in s, is approximated by: CBOOT x V tCHARGE = 500 Where CBOOT is the value of the bootstrap capacitor in nF and V is the required voltage of the bootstrap capacitor. At power up and when the drivers have been disabled for a long time, the bootstrap capacitor can be completely discharged . In this case V can be considered to be the full high side drive voltage, 12 V. Else, V is the amount of voltage dropped during the charge transfer, which should be 400 mV or less. The capacitor is charged whenever the Sx terminal is pulled low and current flows from VREG through the internal bootstrap diode circuit to CBOOT. Supply Decoupling Since this is a switching circuit there will be current spikes from on VBB at the switching points. As with all such circuits the power supply connections should be decoupled with a ceramic capacitor, typically 220 nF, between the supply terminal and ground. These capacitors should be connected as close as possible to the VBB and ground terminal (GND). VREG Capacitor Selection The internal reference (VREG) supplies current for the low-side gate-drive circuits and the charging current for the bootstrap capacitors. When a low-side MOSFET is turned on, the gatedrive circuit will provide the high transient current to the gate that is necessary to turn the MOSFET on quickly. This current, which can be several hundred milliamperes, cannot be provided directly by the limited output of the VREG regulator but must be supplied by an external capacitor connected to VREG. The turn on current for the high-side MOSFET is similar in value but is mainly supplied by the bootstrap capacitor. However the bootstrap capacitor must then be recharged from the VREG regulator output. Unfortunately the bootstrap recharge can occur a very short time after the low-side turn on occurs. This means that the value of the capacitor connected between VREG and GND should be high enough to minimize the transient voltage drop on VREG for the combination of a low-side MOSFET turn on and a bootstrap capacitor recharge. A value of 20 x CBOOT is a reasonable value. The maximum working voltage will never exceed VREG so can be set as low as 15 V. This capacitor should be placed as close as possible to the VREG terminal. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 13 A5929 Automotive Full-Bridge MOSFET Driver INPUT/OUTPUT STRUCTURES Cx VBRG 18 V 20V VBB GHx 20V CP1 14V CP2 VREG 7.5 V Sx VREG 20 V 20 V 8V 18 V 18 V 20 V 20 V 18 V 14 V 18 V GLx 18 V LSS Figure 4a: Gate Drive Outputs Figure 4b: Supplies 4,5 V(max) 4 k 2 k xHI xLO 25 VDSTH FAULT 50 k 6V 6V Figure 4c: xHI, xLO Inputs 6V Figure 4d: VDSTH Input 6V 6V Figure 4e: FAULT Output Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 14 A5929 Automotive Full-Bridge MOSFET Driver LAYOUT RECOMMENDATIONS Optional Reverse Battery protection VBB VBRG + Supply VREG GHB GHA SA A5929 VDD Load SB GLA GLB VDSTH LSS GND PAD Optional Components to Limit LSS Transients Controller Supply RS Power Ground Supply Common Figure 5: Supply Routing Suggestion Careful consideration must be given to PCB layout when designing high frequency, fast-switching, high-current circuits: close to the GND terminal. The decoupling capacitors should also be connected as close as possible to the relevant supply terminal. The A5929 ground, GND, and the high-current return of the external MOSFETs should return separately to the negative side of the motor supply filtering (DC-link) capacitor. This will minimize the effect of bridge switching noise on the A5929. Check the peak voltage excursion of the transients on the LSS terminal with reference to the GND terminal using a closegrounded (tip & barrel) probe. If the voltage at LSS exceeds the absolute maximum in the datasheet, add additional clamping and/ or capacitance between the LSS terminal and the GND terminal as shown. The exposed thermal pad should be connected to GND. Minimize stray inductance by using short, wide copper tracks at the drain and source terminals of all power MOSFETs. This includes motor lead connections, the input power bus, and the common source of the low-side power MOSFETs. This will minimize voltages induced by fast switching of large load currents. Consider the use of small (100 nF) ceramic decoupling capacitors across the source and drain of the power MOSFETs to limit fast transient voltage spikes caused by track inductance. Keep the gate discharge return connections Sx and LSS as short as possible. Any inductance on these tracks will cause negative transitions on the corresponding A5929 terminals, which may exceed the absolute maximum ratings. If this is likely, consider the use of clamping diodes to limit the negative excursion on these terminals with respect to GND. The sensitive VDSTH input should be connected independently Gate charge drive paths and gate discharge return paths may carry a large transient current pulse. Therefore the traces from GHx, GLx, Sx (x = A or B) and LSS should be as short as possible to reduce the track inductance. Provide an independent connection from LSS to the common point of the power bridge. It is not recommended to connect LSS directly to the GND terminal as this may inject noise into sensitive functions such as the various voltage monitors. A low cost diode can be placed in the connection to VBB to provide reverse battery protection. In reverse battery conditions it is possible to use the body diodes of the power MOSFETs to clamp the reverse voltage to approximately 4 V. In this case the additional diode in the VBB connection will prevent damage to the A5929 and the VBRG terminal will survive the reverse voltage. Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 15 A5929 Automotive Full-Bridge MOSFET Driver CUSTOMER PACKAGE DRAWING For Reference Only - Not for Tooling Use (Reference MO-153 ADT) NOT TO SCALE Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown 0.45 7.80 0.10 0.65 8 0 4.32 NOM 24 0.20 0.09 1.65 B 3 NOM 4.400.10 6.400.20 3.00 6.10 A 0.60 0.15 1.00 REF 1 2 0.25 BSC C 24X 1.20 MAX 0.10 C 0.30 0.19 0.65 BSC SEATING PLANE 4.32 SEATING PLANE GAUGE PLANE A 0.15 0.00 C PCB Layout Reference View Terminal #1 mark area B Exposed thermal pad (bottom surface); dimensions may vary with device C Reference land pattern layout (reference IPC7351 TSOP65P640X120-25M); all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances; when mounting on a multilayer PCB, thermal vias at the exposed thermal pad land can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5) Figure 6: Package LP, 24-Pin eTSSOP with Exposed Thermal Pad Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 16 A5929 Automotive Full-Bridge MOSFET Driver Revision History Revision Revision Date - February 11, 2015 0.1 March 3, 2015 Description of Revision Initial Release Corrected typos and revised IBBQ and IBBS values Copyright (c)2015, Allegro MicroSystems, LLC Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro's products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of Allegro's product can reasonably be expected to cause bodily harm. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, LLC 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 17