Plastic Film Capacitors Stacked Metallized PPS Film Chip Capacitor Type: ECHU(C) Stacked metallized PPS film as dielectric with simple mold-less construction Features * Small in size * Low loss and excellent frequency characteristics * For reflow soldering * RoHS directive compliant Recommended Applications * Time-constant * Filtering * Oscillation and resonance * Resonance circuit for LCD backlight inverter unit Explanation of Numbers 1 2 3 4 5 E C H U 1 Product code Dielectric & construction 6 8 9 10 11 C Rated voltage 1 7 Capacitance 100 VDC Cap. Tol. Suffix G 2 % J 5 % Suffix 9 V Tape width 12 mm 16 mm Specifications Category temp. range (Including temperature-rise on unit surface) -55 to 105 Rated voltage 100 VDC Capacitance range 0.010 F to 0.22 F(E12) Capacitance tolerance 2 %(G),5 %(J) Withstand voltage Between terminals : Rated volt. (VDC)150 % 60 s Dissipation factor (tan ) tan0.6 % (20 , 1 kHz) Insulation resistance (IR) IR3000 (20 , 100 VDC, 60 s) Soldering conditions Reflow soldering : 260 C max. and 95 s max. at more than 220 C (Temp. at cap. Surface) In case of applying voltage in alternating current (50 Hz or 60 Hz sine wave) to a capacitor with DC rated voltage, please refer to the page of "Permissible voltage (R.M.S) in alternating current corresponding to DC rated voltage". Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail. Plastic Film Capacitors Dimensions in mm (not to scale) Construction size L W H code E1 4.8 3.3 1.4 E2 4.8 3.3 2.0 E3a 4.8 3.3 2.4 E3 4.8 3.3 2.8 D1 6.0 4.1 1.8 D2 6.0 4.1 2.0 D3 6.0 4.1 2.4 D4 6.0 4.1 2.8 D5 6.0 4.1 3.2 Z 7.1 5.0 Y 7.1 6.3 Refer to the column " Rating,Dimensions&Quantity" Taping Specification for Automatic Mounting Refer to the page of taping specifications. Rating, Dimensions & Quantity/Reel Capacitance tolerance: 2 % (G), 5 % (J) Rated volt. 100 VDC Cap.(F) 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 Part No. ECHU1103C9 ECHU1123C9 ECHU1153C9 ECHU1183C9 ECHU1223C9 ECHU1273C9 ECHU1333C9 ECHU1393C9 ECHU1473C9 ECHU1563C9 ECHU1683C9 ECHU1823C9 ECHU1104C9 ECHU1124C9 ECHU1154CV ECHU1184CV ECHU1224CV Dimensions (mm) L 4.8 4.8 4.8 4.8 4.8 4.8 6.0 6.0 6.0 6.0 6.0 7.1 7.1 7.1 7.1 7.1 7.1 W 3.3 3.3 3.3 3.3 3.3 3.3 4.1 4.1 4.1 4.1 4.1 5.0 5.0 5.0 6.3 6.3 6.3 H 1.4 1.4 2.0 2.0 2.4 2.8 1.8 2.0 2.4 2.8 3.2 2.8 3.0 3.4 3.4 4.0 4.8 Size Code E1 E1 E2 E2 E3a E3 D1 D2 D3 D4 D5 Z Z Z Y Y Y Q'ty 3000 2000 3000 2000 1500 1000 Cap. tol. code Recommended for Land Dimensions (mm) Land dimensions Size code E1,E2,E3a,E3 D1,D2,D3,D4,D5 Z Y Reflow soldering A B C 2.6 3.8 4.5 4.5 6.6 7.8 9.0 9.0 3.0 3.8 4.6 5.7 It is not warrantable that you can mount the capacitor without trouble under all the mounting condition when "Recommender for Land dimensions" is adopted. Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail. ECHU (C) Type DC100V series (Stacked Metallized Film) Electrical Characteristics <Typical Data > Temperature Characteristics at 1kHz 10 5 0 0.01uF,0.068uF,0.22uF -5 Capacitance change(%) Capacitance change(%) 10 Frequency Characteristics -10 5 0.22uF 0.068uF 0.01uF 0 -5 -10 -60 -40 -20 0 20 40 60 80 100 120 140 1 10 Temperature(Degree C) at 1kHz 4 3 2 1 0.01uF,0.068uF,0.22uF 0 -60 -40 -20 0 8 6 4 2 0.22uF 0 0.068uF 0.01uF 20 40 60 80 100 120 140 1 10 100 1000 Frequency(kHz) at DC100V 100 0.01uF 1.E+11 0.068uF 1.E+10 0.22uF 1.E+09 1.E+08 1.E+07 1.E+06 0.01uF Impedance(ohm) Insulation resistance(ohm) Temperature(Degree C) 1.E+12 1000 10 Dissipation factor(%) Dissipation factor(%) 5 100 Frequency(kHz) 10 1 0.068uF 0.22uF 0.1 0.01 -60 -40 -20 0 20 40 60 80 100 120 140 Temperature(Degree C) 100 1000 10000 Frequency(kHz) 100000 ECHU (C) Type DC100V series (Stacked Metallized Film) Applicable Specifications Permissible Current Permissible Voltage 2.5 (at sine wave) 0.22uF 0.18uF 0.15uF Effective value (Arms) 2.0 0.12uF 0.1uF 1.5 0.082uF 0.068uF 0.056uF 0.047uF 1.0 0.039uF Effective value (Vrms) 100 0.01uF to 0.027uF 0.033uF to 0.056uF 0.068uF 0.082uF 0.1uF 0.12uF 0.15uF 0.033uF 0.027uF 0.022uF 0.018uF 0.015uF 0.012uF 0.01uF 0.5 0.18uF 0.22uF 0.0 10 Frequency(kHz) 10 100 Pulse Handling Capability (dv/dt) 0.010 103 1.80 0.012 123 2.16 0.015 153 0.018 183 0.022 223 3.96 0.027 273 4.86 0.033 333 4.29 0.039 393 5.07 0.047 473 0.056 563 7.28 0.068 683 8.84 0.082 823 8.20 0.10 104 10.00 0.12 124 0.15 154 0.18 184 18.00 0.22 224 22.00 180 130 100 200 Current(0-P) (A) 2.70 150 3.24 6.11 DC Rated Voltage (V) DC 100V dV/dt (V/us) 100 Voltage Derating by Temperature (Max 10000cycles) Rating Capacitance code Voltage Value(uF) Frequency(kHz) 10 0.01uF to 0.22uF 100 50 12.00 15.00 0 -60 -40 -20 0 20 40 60 80 100 120 140 Surface Temperature of Capacitor(DegreeC) *Please consult Panasonic if your condition exceeds the above *Permissible voltage graph is the case of sine waveform. When you use this product, peak voltage must not exceed DC rated voltage. *The current(0-P) value is calculated using nominal capacitance. Panasonic Caution about Safety in Use 3.1. Washing of chip type Since the chip type capacitor does not have a coating, components of flux or detergent left over on the element at the time of washing may be activated and invade into the inside of the capacitor, and adverse effects may be caused. Observe the following cautions. In the case of washing, use flux and cream solder with halogen content of 0.1wt.% or less when mounting. In the case of ultrasonic washing, note that peeling of protective film, electrode separation due to resonance, or characteristic deterioration may occur depending on the detergent used or ultrasonic output. Check carefully beforehand. When using a CFC substitute detergent, with the washing method of spraying detergent (rinsing water) to the substrate at high pressure, the protective film on the element surface may be peeled off due to the water pressure. Check carefully beforehand. 2.4.2 Cautions for use of soldering iron Be careful that the soldering irons do not directly touch the main body of the chip film capacitor. In particular, don't touch the side (cut section). If touched by the heated soldering iron, lowering of insulation resistance, shortcircuit or other characteristic deterioration may occur. Preheat the printed wining board land sufficiently with the soldering iron, and then solder. Solder without directly touching the iron tip to the electrode of the capacitor. Don't reuse the products once removed by the soldering irons. Should not mount the chip film capacitors in the mass production by soldering iron. (The temperature control is difficult, and the characteristics may be deteriorated.) Should not resolder with heat directly from bottom side of P. W. Board. because capacitor will likely be damaged. 3. Washing the mounted boards Usable detergent and washing method (Usable detergent Classification Detergent name Alcohol derivative Maker IPA (isopropyl alcohol) Halogenated hydrocarbon (Reagent for general industrial use) AK-225AES (Washing method) Condition Item Asahi Glass Co. Temperature Tine Immersion washing 50 Within 5 minutes Steam washing 50 Within 5 minutes Ultrasonic washing 50 Within 5 minutes <CFC substiture detergent> As a result of regulation of CFC and chlorine derivative detergents, many substitute detergents come to be used, but the performance of the chip type capacitor may be reduced depending on the type of detergent or washing condition. Check sufficiently beforehand. Consult us in advance if planning to use CFC substitute detergent. 3.2. Washing of leaded type The film capacitor varies significantly in the effect of washing depending on the structure and material, and generally it is less affected by CFC or alcohol derivative washing solvent, and is likely to be affected by highly polar solvent. The lead type film capacitor is coated with an epoxy resin excellent in chemical resistance, and is hardly affected by detergent, but it is recommended to be washed for short duration. <Drying after washing> Dry after washing so that the detergent is not left over. If drying is insufficient, the detergent is left over on the element surface, and the insulation resistance is measured to be lowered. Dry enough so as not to leave detergent. Applicability of detergents in film capacitors is listed for reference. DesignSpecifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail. 11 Sep. 2008 Panasonic Caution about Safety in Use List of applicability of detergents Box type Washing condition Chip type Lead type Ethanol Ultrasonic washing or immersion washing for 5 min Isopropyl alcohol (IPA) Ultrasonic washing or immersion washing for 5 min FRW-17 Ultrasonic washing for 5 min, 60 FRW-1N Ultrasonic washing for 5 min, 60 FRW-100 Steam drying for 1 min, 100 Asahi Clean AK-225AES Ultrasonic washing or immersion washing for 5 min HCFC141b-MS Ultrasonic washing or immersion washing for 5 min P3 Cold Cleaner 225S Ultrasonic washing for 5 min 60 IPA ultrasonic rinsing for 5 min at ordinary temperature hot air drying for 5 min, 40 Toluene Ultrasonic washing or immersion washing for 5 min x Terpene Cleaner EC-7 Spray washing for 5 min at ordinary temperature purified water spraying for 5 min, 50 hot air drying for 5 min, 80 x Ultrasonic washing for 5 min 60 wind-free drying for 5 min, 85 x Clean Through 750H Ultrasonic washing for 5 min, 60 purified water ultrasonic washing for 5 min, 60 hot air drying for 5 min, 85 x Clean Through 750L Ultrasonic washing for 5 min, 60 purified water ultrasonic washing for 5 min, 60 hot air drying for 5 min, 85 x Clean Through 710M Ultrasonic washing for 5 min, 60 purified water ultrasonic washing for 5 min, 60 hot air drying for 5 min, 85 x Clean Through LC-841 Ultrasonic washing for 5 min, 60 purified water ultrasonic washing for 5 min, 60 hot air drying for 5 min, 85 x Ultrasonic washing for 5 min, 60 purified water ultrasonic washing for 5 min, 60 hot air drying for 5 min, 85 x Shower washing for 1 min, 60 purified water ultrasonic washing for 5 min, 60 hot air drying for 5 min, 85 x ECQUL Alcohol Solvent Silicon Halogen Petroleum hydrocarbon Terpene Water Purified water Surface active agent : Washing enabled Wash-fre e Wash-free flux Low residue flux Inactivated flux x : Washing disabled : Not confirmed ULF-500VS AM-173 Washing disabled (x mark) detergent should be avoided because the appearance may be impaired, the characteristic may be deteriorated, and the reliability cannot be guaranteed DesignSpecifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use. Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail. -12- Jul. 2011