US
UK
Taiwan
China
Singapore
+1-847-639-6400 sales@coilcraft.com
+44-1236-730595 sales@coilcraft-europe.com
+886-2-2264 3646 sales@coilcraft.com.tw
+86-21-6218 8074 sales@coilcraft.com.cn
+ 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft appr
oval.
Specification subject to change without notice.
Please check web site for latest infor
mation.
Document 757-1
Coupled Inductors LPD5030
Document 757-1 Revised 06/21/13
2
14
3
L1
L2
Dimensions are in inches
mm
0.060
1,52
0.114 ±0.004
2,90 ±0,10
Dash
number Internal
code
Dot indicates pin 1
0.189 ±0.003
4,80 ±0,076
0.189 ±0.003
4,80 ±0,076
XXX X
14
23
Recommended
Land Pattern
0.197
5,00
0.134
3,40
0.060
1,50
0.138
3,50
0.197
5,00
45°
typ
0.090
2,30
0.134
3,40
0.090
2,30
0.030
0,75
The LPD5030 coupled miniature shielded inductors are
only 3 mm high and 5 mm square. They are ideal for
use in a variety of circuits including flyback, multi-output
buck and SEPIC.
These inductors provide high inductance, high efficiency
and excellent current handling in a rugged, low cost part.
They can also be used as two single inductors connected
in series or parallel or as a common mode choke.
L1 L2
++
–
–
D
C
C
Typical Flyback Converter
VOUT
V
IN
SW
L1
L2
++
+
––
–
D
D
C
C
SW
Typical Buck Converter with auxiliary output
VOUT
VOUTAU
X
V
IN
Typical Zeta schematic
VOUT
V
IN L1
L2
QC1
CC
++
––
D
Typical SEPIC schematic
VOUT
V
IN
L1
L2
Q
C1
C
C
++
––
D
For Flyback, SEPIC, Zeta
and other Applications
Specifications subject to change without notice.
Please check our website for latest information.
US
UK
Taiwan
China
Singapore
+1-847-639-6400 sales@coilcraft.com
+44-1236-730595 sales@coilcraft-europe.com
+886-2-2264 3646 sales@coilcraft.com.tw
+86-21-6218 8074 sales@coilcraft.com.cn
+ 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft appr
oval.
Specification subject to change without notice.
Please check web site for latest infor
mation.
Coupled Inductors for SEPIC Applications – LPD5030 Series
Document 757-2
Document 757-2 Revised 06/21/13
Coupling Leakage Isat (A)6 Irms (A)
Inductance2 DCR max3 SRF typ4 coefficient
L typ5 10% 20% 30% both one
Part number1 (µH) (Ohms) (MHz) typ (µH) drop drop drop windings7
winding8
LPD5030-102NE_ 1.0 ±30% 0.042 153 0.95 0.09 4.30 4.49 4.67 2.20 3.11
LPD5030-152ME_ 1.5 ±20% 0.048 118 0.97 0.09 3.90 4.20 4.30 2.05 2.90
LPD5030-222ME_ 2.2 ±20% 0.067 87.0 0.98 0.10 2.80 2.98 3.07 1.95 2.76
LPD5030-332ME_ 3.3 ±20% 0.077 61.0 0.98 0.10 2.50 2.70 2.80 1.70 2.40
LPD5030-472ME_ 4.7 ±20% 0.111 49.0 0.99 0.11 2.10 2.20 2.20 1.40 1.98
LPD5030-562ME_ 5.6 ±20% 0.125 44.0 0.99 0.11 1.80 1.80 1.89 1.35 1.91
LPD5030-682ME_ 6.8 ±20% 0.159 40.0 0.99 0.12 1.40 1.48 1.48 1.20 1.70
LPD5030-103ME_ 10 ±20% 0.210 28.0 0.99 0.13 1.20 1.20 1.20 1.05 1.48
LPD5030-153ME_ 15 ±20% 0.298 23.0 0.99 0.15 1.00 1.17 1.17 0.85 1.20
LPD5030-223ME_ 22 ±20% 0.452 17.0 >0.99 0.17 0.89 0.98 0.98 0.70 0.99
LPD5030-333ME_ 33 ±20% 0.565 16.0 >0.99 0.20 0.73 0.77 0.78 0.60 0.85
LPD5030-473ME_ 47 ±20% 0.806 12.0 >0.99 0.24 0.59 0.63 0.65 0.50 0.71
LPD5030-683ME_ 68 ±20% 1.13 9.00 >0.99 0.29 0.50 0.54 0.55 0.43 0.61
LPD5030-104ME_ 100 ±20% 1.79 8.44 >0.99 0.37 0.47 0.54 0.56 0.33 0.47
LPD5030-154ME_ 150 ±20% 2.43 6.72 >0.99 0.46 0.38 0.43 0.45 0.28 0.40
LPD5030-224ME_ 220 ±20% 3.30 5.53 >0.99 0.54 0.31 0.35 0.36 0.24 0.34
LPD5030-334ME_ 330 ±20% 5.36 4.17 >0.99 0.65 0.25 0.25 0.32 0.18 0.25
LPD5030-474ME_ 470 ±20% 7.51 3.52 >0.99 0.76 0.21 0.24 0.26 0.15 0.21
LPD5030-684ME_ 680 ±20% 10.8 2.93 >0.99 0.89 0.17 0.20 0.21 0.13 0.18
LPD5030-105ME_ 1000 ±20% 16.5 2.33 >0.99 1.20 0.15 0.17 0.17 0.10 0.14
1. Please specify termination and packaging codes:
LPD5030-105MEC
Termination: E = RoHS compliant, halogen free silver-palladium-
platinum-glass frit.
Special order:
T = RoHS tin-silver-copper (95.5/4/0.5) or
S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (750 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (2500 parts per
full reel).
2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms,
0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads
are connected in parallel, inductance is the same value. When leads
are connected in series, inductance is four times the value.
3. DCR is for each winding. When leads are connected in parallel, DCR
is half the value. When leads are connected in series, DCR is twice the
value.
4. SRF measured using an Agilent/HP 4191A or equivalent. When leads
are connected in parallel, SRF is the same value.
5. Leakage Inductance is for L1 and is measured with L2 shorted.
6. DC current, at which the inductance drops the specified amount from
its value without current. It is the sum of the current flowing in both
windings.
7. Equal current when applied to each winding simultaneously that
causes a 40°C temperature rise from 25°C ambient. See temperature
rise calculation.
8. Maximum current when applied to one winding that causes a 40°C
temperature rise from 25°C ambient. See temperature rise calculation.
9. Electrical specifications at 25°C.
Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.”
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Coupled Inductor Core and Winding Loss Calculator
This web-based utility allows you to enter frequency, peak-to-peak
(ripple) current, and Irms current to predict temperature rise and overall
losses, including core loss. Go to online calculator.
Core material Ferrite
Core and winding loss Go to online calculator
Weight 210 – 225 mg
Terminations RoHS compliant, halogen free silver-palladium-platinum
glass frit. Other terminations available at additional cost.
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Winding to winding isolation 100 V
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Mean Time Between Failures (MTBF) 26,315,789 hours
Packaging 750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide,
0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
PCB washing Only pure water or alcohol recommended
Specifications subject to change without notice.
Please check our website for latest information.
US
UK
Taiwan
China
Singapore
+1-847-639-6400 sales@coilcraft.com
+44-1236-730595 sales@coilcraft-europe.com
+886-2-2264 3646 sales@coilcraft.com.tw
+86-21-6218 8074 sales@coilcraft.com.cn
+ 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft appr
oval.
Specification subject to change without notice.
Please check web site for latest infor
mation.
Coupled Inductors for SEPIC Applications – LPD5030 Series
Document 757-3
Document 757-3 Revised 06/21/13
Typical L vs Current
Typical Current Derating
Typical L vs Frequency
-40 -20 020406080100 140120
Ambient temperature (°C)
Percent of rated current
120
110
100
90
80
70
60
50
40
30
20
10
0
Isat
Irms
25°C
1
10
100
1000
10000
Inductance (µH)
0.1 110010
Frequency (MHz)
100 µH
330 µH
1000 µH
33 µH
10 µH
3.3 µH
1
10
100
1000
10000
Inductance (µH)
0.01 0.1 101
Current (A)
100 µH
330 µH
1000 µH
33 µH
10 µH
3.3 µH
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Coilcraft:
LPD5010-102MRB LPD5030-152MRC LPD5030-222MRC LPD5030-332MRC LPD5030-472MRC LPD5030-
562MRC LPD5030-682MRC LPD5030-103MRC LPD5030-153MRC LPD5030-223MRC LPD5030-333MRC
LPD5030-473MRC LPD5030-683MRC LPD5030-104MRC LPD5030-154MRC LPD5030-224MRC LPD5030-
334MRC LPD5030-474MRC LPD5030-105MRC LPD5030-102NRC LPD5030-152MRB LPD5030-222MRB
LPD5030-332MRB LPD5030-472MRB LPD5030-562MRB LPD5030-682MRB LPD5030-103MRB LPD5030-153MRB
LPD5030-223MRB LPD5030-333MRB LPD5030-473MRB LPD5030-683MRB LPD5030-104MRB LPD5030-
154MRB LPD5030-224MRB LPD5030-334MRB LPD5030-474MRB LPD5030-684MRB LPD5030-105MRB
LPD5030-102NRB LPD5030-684MRC
