Data Sheet 1 2002-10-07
Cage
for Small Form Factor Pluggable (SFP) Transceiver
V23818-S5-N1
V23818-S5-N1-BB
Fiber Optics
Part Number Description
V23818-S5-N1 For single-sided mounting
V23818-S5-N1-BB For double-sided "belly to belly" mounting (see Figure 3)
Features
• Supports MSA compliant host board layouts and
transceiver designs
• One-piece, rigid stainless steel construction with
tin-lead plating
• Simple and fast installation/removal
• Solid retention strength
• Easily press fit onto host board via tear-drop foot
design
• Testing of rear connector may take place before
SFP Cage is installed onto host board
• Low emission design via fold-back spring fingers – no openings for radiation to pass
through
• Enhanced transceiver kick-out and retention springs
• Heat transfer windows on all SFP Cage surfaces
• Cage can be press fit and/or soldered
Description
Infineon is offering its Cage for Small Form Factor Pluggable (SFP) transceivers with the
most rigid mechanical design available on the market. The Cage is designed for press
fit applications in order to reduce high volume manufacturing effort. Press fit pins can be
also soldered if required. Externally bent bezel contact springs and one-piece
construction enhance EMI performance. As part of Infineon's Total Transceiver Solution,
the SFP Cage is your logical choice for next generation pluggable transceivers.
V23818-S5-N1
V23818-S5-N1-BB
Application Notes
Data Sheet 2 2002-10-07
Application Notes
•For single-sided mounting, optimum host board thickness is .059 to .062 in
[1.5 to 1.57 mm]. SFP Cage mounting holes should be plated with HASL, gold, or
immersion silver finish per MSA dimensional recommendations
•For double-sided mounting, host board thickness is .118 in [3.0 mm] minimum per the
MSA. For belly-to-belly applications, one of the rear mounting feet is removed to avoid
interference (V23818-S5-N1-BB)
•Installation of the SFP Cage may be done by hand or with a solid metal block across
the top surface of the Cage. Block dimensions to be controlled by customer
•Removal of the Cage should be done with an internal solid metal block. Due to the
collapsing nature of the teardrop foot design, the Infineon SFP Cage is intended for
one-time installation
•The Infineon SFP Cage does not cause any damage when carefully removed; the
outside profile of the teardrop feet is smooth and will not destroy pre-plated host board
mounting holes
•Trapped fluids from washing process must be dried to prevent corrosion beneath SFP
Cage
•Cage retention depends on finished hole size and plating thickness
System Configurations
•Single-sided mounting with .640 in [16.25 mm] pitch
•Double-sided "belly to belly" mounting with .640 in [16.25 mm] pitch
•Double-sided "offset belly to belly" mounting with .975 in [24.77 mm] pitch
V23818-S5-N1
V23818-S5-N1-BB
Application Notes
Data Sheet 3 2002-10-07
Figure 1 Single-sided Host Board Layout
Figure 2 Single-sided Layout
SINGLE-SIDED LAYOUT
DIMENSIONS IN INCHES [MM]
V23818-S5-N1
V23818-S5-N1-BB
Application Notes
Data Sheet 4 2002-10-07
Figure 3
V23818-S5-N1
V23818-S5-N1-BB
Application Notes
Data Sheet 5 2002-10-07
Single-sided Application
Figure 4
Figure 5
V23818-S5-N1
V23818-S5-N1-BB
Application Notes
Data Sheet 6 2002-10-07
Belly to Belly Application
Figure 6
Figure 7
V23818-S5-N1
V23818-S5-N1-BB
Package Outlines
Data Sheet 7 2002-10-07
Package Outlines
Figure 8
Dimensions in inches [mm]
Edition 2002-10-07
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81541 München, Germany
© Infineon Technologies AG 2002.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as warranted
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide.
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life-support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
For questions on technology, delivery and prices please contact the Infineon
Technologies Offices in Germany or the Infineon Technologies Companies and
Representatives worldwide: see our webpage at http://www.infineon.com.
V23818-S5-N1
V23818-S5-N1-BB
Revision History: 2002-10-07 DS0
Previous Version:
Page Subjects (major changes since last revision)
