TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 Cap-Free, NMOS, 400mA Low-Dropout Regulator with Reverse Current Protection FEATURES 1 * 2 * * * * * * * * * * Stable with No Output Capacitor or Any Value or Type of Capacitor Input Voltage Range of 1.7V to 5.5V Ultra-Low Dropout Voltage: 75mV typ Excellent Load Transient Response--with or without Optional Output Capacitor New NMOS Topology Delivers Low Reverse Leakage Current Low Noise: 30mVRMS typ (10Hz to 100kHz) 0.5% Initial Accuracy 1% Overall Accuracy Over Line, Load, and Temperature Less Than 1mA max IQ in Shutdown Mode Thermal Shutdown and Specified Min/Max Current Limit Protection Available in Multiple Output Voltage Versions - Fixed Outputs of 1.20V to 5.0V - Adjustable Output from 1.20V to 5.5V - Custom Outputs Available APPLICATIONS * * * * Portable/Battery-Powered Equipment Post-Regulation for Switching Supplies Noise-Sensitive Circuitry such as VCOs Point of Load Regulation for DSPs, FPGAs, ASICs, and Microprocessors Optional VIN DESCRIPTION The TPS736xx family of low-dropout (LDO) linear voltage regulators uses a new topology: an NMOS pass element in a voltage-follower configuration. This topology is stable using output capacitors with low ESR, and even allows operation without a capacitor. It also provides high reverse blockage (low reverse current) and ground pin current that is nearly constant over all values of output current. The TPS736xx uses an advanced BiCMOS process to yield high precision while delivering very low dropout voltages and low ground pin current. Current consumption, when not enabled, is under 1mA and ideal for portable applications. The extremely low output noise (30mVRMS with 0.1mF CNR) is ideal for powering VCOs. These devices are protected by thermal shutdown and foldback current limit. space DRB PACKAGE 3mmx 3mm SON (TOP VIEW) OUT 1 DBV PACKAGE SOT23 (TOP VIEW) 8 IN N/C 2 7 N/C IN 1 NR/FB 3 6 N/C GND 2 EN 3 GND 4 5 EN OUT GND 4 NR/FB TAB IS GND 6 VOUT TPS736xx EN OUT DCQ PACKAGE SOT223 (TOP VIEW) Optional IN 5 1 2 3 4 5 NR ON IN OFF Optional GND EN OUT NR/FB Typical Application Circuit for Fixed-Voltage Versions space 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PRODUCT TPS736xx yy yz (1) (2) (3) VOUT (2) XX is nominal output voltage (for example, 25 = 2.5V, 01 = Adjustable (3)). YYY is package designator. Z is package quantity. For the most current specification and package information, refer to the Package Option Addendum located at the end of this datasheet or see the TI website at www.ti.com. Most output voltages of 1.25V and 1.3V to 5.0V in 100mV increments are available on a quick-turn basis using innovative factory EEPROM programming. Minimum order quantities apply; contact factory for details and availability. For fixed 1.20V operation, tie FB to OUT. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) PARAMETER TPS736xx UNIT VIN range -0.3 to 6.0 V VEN range -0.3 to 6.0 V VOUT range -0.3 to 5.5 V VNR, VFB range -0.3 to 6.0 V Peak output current Output short-circuit duration Continuous total power dissipation Internally limited Indefinite See Thermal Information Table Junction temperature range, TJ -55 to +150 Storage temperature range -65 to +150 C ESD rating, HBM 2 kV ESD rating, CDM 500 V (1) 2 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under the Electrical Characteristics is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Submit Documentation Feedback Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 THERMAL INFORMATION TPS736xx (3) THERMAL METRIC (1) (2) Junction-to-ambient thermal resistance (4) qJA (5) DRB DCQ DBV 8 PINS 6 PINS 5 PINS 47.8 70.4 180 64 qJCtop Junction-to-case (top) thermal resistance 83 70 qJB Junction-to-board thermal resistance (6) N/A N/A 35 yJT Junction-to-top characterization parameter (7) 2.1 6.8 N/A yJB Junction-to-board characterization parameter (8) 17.8 30.1 N/A qJCbot Junction-to-case (bottom) thermal resistance (9) 12.1 6.3 N/A (1) (2) (3) (4) (5) (6) (7) (8) (9) UNITS C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953A. For thermal estimates of this device based on PCB copper area, see the TI PCB Thermal Calculator. Thermal data for the DRB, DCQ, and DRV packages are derived by thermal simulations based on JEDEC-standard methodology as specified in the JESD51 series. The following assumptions are used in the simulations: (a) i. DRB: The exposed pad is connected to the PCB ground layer through a 2x2 thermal via array. . ii. DCQ: The exposed pad is connected to the PCB ground layer through a 3x2 thermal via array. . iii. DBV: There is no exposed pad with the DBV package. (b) i. DRB: The top and bottom copper layers are assumed to have a 20% thermal conductivity of copper representing a 20% copper coverage. . ii. DCQ: Each of top and bottom copper layers has a dedicated pattern for 20% copper coverage. . iii. DBV: The top and bottom copper layers are assumed to have a 20% thermal conductivity of copper representing a 20% copper coverage. (c) These data were generated with only a single device at the center of a JEDEC high-K (2s2p) board with 3in x 3in copper area. To understand the effects of the copper area on thermal performance, see the Power Dissipation section of this data sheet. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the top of the package. No specific JEDEC-standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB temperature, as described in JESD51-8. The junction-to-top characterization parameter, yJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data to obtain qJA using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, yJB, estimates the junction temperature of a device in a real system and is extracted from the simulation data to obtain qJA using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. Copyright (c) 2003-2010, Texas Instruments Incorporated Submit Documentation Feedback 3 TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com ELECTRICAL CHARACTERISTICS Over operating temperature range (TJ = -40C to +125C), VIN = VOUT(nom) + 0.5V (1), IOUT = 10mA, VEN = 1.7V, and COUT = 0.1mF, unless otherwise noted. Typical values are at TJ = +25C. PARAMETER TEST CONDITIONS VIN Input voltage range (1) (2) VFB Internal reference (TPS73601) Accuracy (1) (4) VOUT%/VIN MAX UNIT 5.5 TJ = +25C V 1.210 V VFB 5.5 - VDO V +0.5 1.198 Nominal TJ = +25C -0.5 over VIN, IOUT, and T VOUT + 0.5V VIN 5.5V; 10mA IOUT 400mA -1.0 Line regulation (1) VOUT%/IOUT Load regulation 0.01 0.002 10mA IOUT 400mA 0.0005 IOUT = 400mA ZO(DO) Output impedance in dropout 1.7V VIN VOUT + VDO ICL Output current limit ISC Short-circuit current Reverse leakage current 75 IGND GND pin current ISHDN Shutdown current (IGND) IFB FB pin current (TPS73601) +1.0 VOUT = 0.9 x VOUT(nom) 400 3.6V VIN 4.2V, 0C TJ +70C 500 650 % %/V %/mA 200 mV 0.25 VOUT = 0V (-IIN) 0.5 1mA IOUT 400mA Dropout voltage (5) (VIN = VOUT(nom) - 0.1V) (6) 1.20 VO(nom) + 0.5V VIN 5.5V VDO IREV TYP 1.7 Output voltage range (TPS73601) (3) VOUT MIN 800 mA 800 mA 450 mA VEN 0.5V, 0V VIN VOUT 0.1 10 IOUT = 10mA (IQ) 400 550 IOUT = 400mA 800 1000 VEN 0.5V, VOUT VIN 5.5, -40C TJ +100C 0.02 1 mA 0.1 0.3 mA PSRR Power-supply rejection ratio (ripple rejection) VN Output noise voltage BW = 10Hz - 100KHz COUT = 10mF, No CNR 27 x VOUT COUT = 10mF, CNR = 0.01mF 8.5 x VOUT tSTR Startup time VEN(HI) EN pin high (enabled) 1.7 VIN V VEN(LO) EN pin low (shutdown) 0 0.5 V IEN(HI) EN pin current (enabled) 0.1 mA Thermal shutdown temperature TJ Operating junction temperature (1) (2) (3) (4) (5) (6) 4 f = 10KHz, IOUT = 400mA 37 mA f = 100Hz, IOUT = 400mA TSD 58 mA VOUT = 3V, RL = 30 COUT = 1mF, CNR = 0.01mF dB mVRMS 600 VEN = 5.5V 0.02 Shutdown, temperature increasing +160 Reset, temperature decreasing +140 -40 ms C +125 C Minimum VIN = VOUT + VDO or 1.7V, whichever is greater. For VOUT(nom) < 1.6V, when VIN 1.6V, the output will lock to VIN and may result in a damaging over-voltage level on the output. To avoid this situation, disable the device before powering down the VIN. TPS73601 is tested at VOUT = 2.5V. Tolerance of external resistors not included in this specification. VDO is not measured for fixed output versions with VOUT(nom) < 1.8V. Fixed-voltage versions only; refer to Applications section for more information. Submit Documentation Feedback Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 FUNCTIONAL BLOCK DIAGRAMS IN 4MHz Charge Pump EN Thermal Protection Ref Servo 27k Bandgap Error Amp Current Limit OUT 8k GND R1 R1 + R2 = 80k R2 NR Figure 1. Fixed Voltage Version IN Table 1. Standard 1% Resistor Values for Common Output Voltages VO 4MHz Charge Pump EN Thermal Protection Ref Servo 27k Bandgap Error Amp GND R2 1.2V Short Open 1.5V 23.2k 95.3k 1.8V 28.0k 56.2k 2.5V 39.2k 36.5k 2.8V 44.2k 33.2k 3.0V 46.4k 30.9k 3.3V 52.3k 30.1k NOTE: VOUT = (R1 + R2)/R2 x 1.204; R1R2 19k for best accuracy. OUT Current Limit R1 80k 8k R1 FB R2 Figure 2. Adjustable Voltage Version Copyright (c) 2003-2010, Texas Instruments Incorporated Submit Documentation Feedback 5 TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com PIN CONFIGURATIONS IN 1 GND 2 EN 3 DRB PACKAGE 3mm x 3mm SON (TOP VIEW) DCQ PACKAGE SOT223 (TOP VIEW) DBV PACKAGE SOT23 (TOP VIEW) 5 6 OUT 4 TAB IS GND NR/FB 1 IN 2 3 4 OUT 1 8 IN N/C 2 7 N/C NR/FB 3 6 N/C GND 4 5 EN 5 GND EN OUT NR/FB PIN DESCRIPTIONS 6 NAME SOT23 (DBV) PIN NO. SOT223 (DCQ) PIN NO. 3x3 SON (DRB) PIN NO. IN 1 1 8 GND 2 3, 6 4, Pad EN 3 5 5 Driving the enable pin (EN) high turns on the regulator. Driving this pin low puts the regulator into shutdown mode. Refer to the Shutdown section under Applications Information for more details. EN can be connected to IN if not used. NR 4 4 3 Fixed voltage versions only--connecting an external capacitor to this pin bypasses noise generated by the internal bandgap, reducing output noise to very low levels. FB 4 4 3 Adjustable voltage version only--this is the input to the control loop error amplifier, and is used to set the output voltage of the device. OUT 5 2 1 Output of the Regulator. There are no output capacitor requirements for stability. Submit Documentation Feedback DESCRIPTION Input supply Ground Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 TYPICAL CHARACTERISTICS For all voltage versions, at TJ = +25C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1mF, unless otherwise noted. LOAD REGULATION LINE REGULATION 0.20 0.5 Referred to IOUT = 10mA -40_C +25_C +125_ C Change in VOUT (%) 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 Referred to VIN = VOUT + 0.5V at IOUT = 10mA 0.15 Change in VOUT (%) 0.4 0.10 0 -0.05 -40_ C -0.10 -0.15 -0.4 -0.20 -0.5 0 50 100 150 200 250 300 350 0 400 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VIN - VOUT (V) IOUT (mA) Figure 3. Figure 4. DROPOUT VOLTAGE vs OUTPUT CURRENT 100 DROPOUT VOLTAGE vs TEMPERATURE 100 TPS73625DBV +125_ C 80 80 60 VDO (mV) VDO (mV) +25_ C +125_C 0.05 +25_ C 40 -40_C 20 50 100 150 200 250 300 60 40 20 0 -50 0 0 TPS73625DBV I OUT = 400mA 350 400 -25 0 25 50 IOUT (mA) Temperature (_ C) Figure 5. Figure 6. OUTPUT VOLTAGE ACCURACY HISTOGRAM 75 100 125 OUTPUT VOLTAGE DRIFT HISTOGRAM 30 18 IOUT = 10mA 16 25 IOUT = 10mA All Voltage Versions Percent of Units (%) Percent of Units (%) 14 20 15 10 12 10 8 6 4 5 2 0 -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 0 VOUT Error (%) Worst Case dVOUT/dT (ppm/_C) Figure 7. Copyright (c) 2003-2010, Texas Instruments Incorporated Figure 8. Submit Documentation Feedback 7 TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) For all voltage versions, at TJ = +25C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1mF, unless otherwise noted. GROUND PIN CURRENT vs OUTPUT CURRENT GROUND PIN CURRENT vs TEMPERATURE 900 900 800 800 700 700 600 600 I GND (A) 1000 IGND (A) 1000 500 400 300 500 400 300 VIN = 5.5V VIN = 4V VIN = 2V 200 100 0 100 200 300 VIN = 5.5V VIN = 3V VIN = 2V 200 100 0 0 -50 400 -25 0 25 50 75 IOUT (mA) Temperature (_C) Figure 9. Figure 10. GROUND PIN CURRENT in SHUTDOWN vs TEMPERATURE CURRENT LIMIT vs VOUT (FOLDBACK) 1 100 125 800 TPS73633 VENABLE = 0.5V VIN = VO + 0.5V 700 ICL Output Current (mA) IGND (A) IOUT = 400mA 0.1 600 500 ISC 400 300 200 100 0.01 -50 -25 0 25 50 75 100 0 -0.5 125 0 0.5 Figure 11. 2.0 2.5 3.0 3.5 CURRENT LIMIT vs TEMPERATURE 800 800 750 750 700 700 Current Limit (mA) Current Limit (mA) 1.5 Figure 12. CURRENT LIMIT vs VIN 650 600 550 500 450 650 600 550 500 450 400 1.5 2.0 2.5 3.0 3.5 VIN (V) Figure 13. 8 1.0 Output Voltage (V) Temperature (_C) Submit Documentation Feedback 4.0 4.5 5.0 5.5 400 -50 -25 0 25 50 75 100 125 Temperature (_C) Figure 14. Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 TYPICAL CHARACTERISTICS (continued) For all voltage versions, at TJ = +25C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1mF, unless otherwise noted. PSRR (RIPPLE REJECTION) vs FREQUENCY PSRR (RIPPLE REJECTION) vs VIN - VOUT 90 40 IOUT = 100mA COUT = Any Ripple Rejection (dB) 70 IOUT = 1mA COUT = 1F 35 30 IOUT = 1mA COUT = 10F 60 50 IO = 100mA CO = 1F IOUT = 1mA C OUT = Any 40 25 PSRR (dB) 80 20 15 30 20 IOUT = Any COUT = 0F 10 VIN = VOUT + 1V 0 10 100 1k 10k Frequency = 10kHz COUT = 10mF VOUT = 2.5V IOUT = 100mA 10 I OUT = 100mA COUT = 10F 5 0 100k 1M 0 10M 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 Frequency (Hz) VIN - VOUT (V) Figure 15. Figure 16. NOISE SPECTRAL DENSITY CNR = 0mF NOISE SPECTRAL DENSITY CNR = 0.01mF 1 1.8 2.0 1 COUT = 0F 0.1 COUT = 10F eN (V/Hz) eN (V/Hz) C OUT = 1F COUT = 1F 0.1 COUT = 0F COUT = 10F IOUT = 150mA IOUT = 150mA 0.01 0.01 10 100 1k 10k 100k 10 100 1k Frequency (Hz) Frequency (Hz) Figure 17. Figure 18. RMS NOISE VOLTAGE vs COUT 10k 100k RMS NOISE VOLTAGE vs CNR 60 140 50 120 VOUT = 5.0V VOUT = 5.0V 100 30 VN (RMS) VN (RMS) 40 VOUT = 3.3V 80 VOUT = 3.3V 60 20 40 VOUT = 1.5V 10 0 20 CNR = 0.01F 10Hz < Frequency < 100kHz 0.1 0 1 10 VOUT = 1.5V COUT = 0F 10Hz < Frequency < 100kHz 1p 10p 100p COUT (F) CNR (F) Figure 19. Figure 20. Copyright (c) 2003-2010, Texas Instruments Incorporated 1n 10n Submit Documentation Feedback 9 TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) For all voltage versions, at TJ = +25C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1mF, unless otherwise noted. TPS73633 LOAD TRANSIENT RESPONSE VIN = 3.8V TPS73633 LINE TRANSIENT RESPONSE COUT = 0F 100mV/tick IOUT = 400mA VOUT COUT = 0F 50mV/div COUT = 1F 50mV/tick COUT = 10F 20mV/tick VOUT VOUT VOUT COUT = 100F 50mV/div VOUT dVIN 5.5V 400mA IOUT 50mA/tick 10mA 4.5V 1V/div VIN 10s/div 10s/div Figure 21. Figure 22. TPS73633 TURN-ON RESPONSE TPS73633 TURN-OFF RESPONSE RL = 1k CO UT = 0F R L = 20 C OUT = 10F VOUT RL = 20 COUT = 1F 1V/div R L = 20 C OUT = 1F 1V/div R L = 1k C OUT = 0F RL = 20 COUT = 10F VOUT 2V 2V VEN 1V/div 1V/div 0V 0V VEN 100s/div 100s/div Figure 23. Figure 24. TPS73633 POWER UP / POWER DOWN IENABLE vs TEMPERATURE 10 6 5 4 VIN VOUT IENABLE (nA) 3 Volts = 0.5V/s dt 2 1 1 0.1 0 -1 -2 50ms/div 0.01 -50 -25 0 25 50 75 100 125 Temperature (_ C) Figure 25. 10 Submit Documentation Feedback Figure 26. Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 TYPICAL CHARACTERISTICS (continued) For all voltage versions, at TJ = +25C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1mF, unless otherwise noted. TPS73601 IFB vs TEMPERATURE 60 160 55 140 50 120 45 100 IFB (nA) VN (rms) TPS73601 RMS NOISE VOLTAGE vs CFB 40 60 35 30 25 80 VOUT = 2.5V COUT = 0F R1 = 39.2k 10Hz < Frequency < 100kHz 20 10p 100p 40 20 1n 10n 0 -50 -25 0 25 50 75 100 CFB (F) Temperature (_C) Figure 27. Figure 28. TPS73601 LOAD TRANSIENT, ADJUSTABLE VERSION TPS73601 LINE TRANSIENT, ADJUSTABLE VERSION CFB = 10nF R1 = 39.2k COUT = 0F 200mV/div VOUT COUT = 0F COUT = 10F 200mV/div VOUT = 2.5V CFB = 10nF 100mV/div COUT = 10F 100mV/div 125 VOUT VOUT VOUT 4.5V 400mA 3.5V VIN 10mA IOUT 25s/div 5s/div Figure 29. Figure 30. Copyright (c) 2003-2010, Texas Instruments Incorporated Submit Documentation Feedback 11 TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com APPLICATION INFORMATION The TPS736xx belongs to a family of new generation LDO regulators that use an NMOS pass transistor to achieve ultra-low-dropout performance, reverse current blockage, and freedom from output capacitor constraints. These features, combined with low noise and an enable input, make the TPS736xx ideal for portable applications. This regulator family offers a wide selection of fixed output voltage versions and an adjustable output version. All versions have thermal and over-current protection, including foldback current limit. Figure 31 shows the basic circuit connections for the fixed voltage models. Figure 32 gives the connections for the adjustable output version (TPS73601). Optional input capacitor. May improve source impedance, noise, or PSRR. VIN Optional output capacitor. May improve load transient, noise, or PSRR. IN TPS736xx GND NR ON OFF Optional bypass capacitor to reduce output noise. Figure 31. Typical Application Circuit for Fixed-Voltage Versions Optional input capacitor. May improve source impedance, noise, or PSRR. VIN IN Optional output capacitor. May improve load transient, noise, or PSRR. EN OFF VOUT OUT TPS73601 GND R1 CFB FB ON R2 VOUT = (R1 + R2) INPUT AND OUTPUT CAPACITOR REQUIREMENTS Although an input capacitor is not required for stability, it is good analog design practice to connect a 0.1mF to 1mF low ESR capacitor across the input supply near the regulator. This counteracts reactive input sources and improves transient response, noise rejection, and ripple rejection. A higher-value capacitor may be necessary if large, fast rise-time load transients are anticipated or the device is located several inches from the power source. VOUT OUT EN For best accuracy, make the parallel combination of R1 and R2 approximately equal to 19k. This 19k, in addition to the internal 8k resistor, presents the same impedance to the error amp as the 27k bandgap reference output. This impedance helps compensate for leakages into the error amp terminals. x 1.204 R2 Optional capacitor reduces output noise and improves transient response. The TPS736xx does not require an output capacitor for stability and has maximum phase margin with no capacitor. It is designed to be stable for all available types and values of capacitors. In applications where multiple low ESR capacitors are in parallel, ringing may occur when the product of COUT and total ESR drops below 50nF. Total ESR includes all parasitic resistances, including capacitor ESR and board, socket, and solder joint resistance. In most applications, the sum of capacitor ESR and trace resistance will meet this requirement. OUTPUT NOISE A precision band-gap reference is used to generate the internal reference voltage, VREF. This reference is the dominant noise source within the TPS736xx and it generates approximately 32mVRMS (10Hz to 100kHz) at the reference output (NR). The regulator control loop gains up the reference noise with the same gain as the reference voltage, so that the noise voltage of the regulator is approximately given by: (R1 ) R2) + 32mVRMS R2 V N + 32mVRMS Figure 32. Typical Application Circuit for Adjustable-Voltage Version R1 and R2 can be calculated for any output voltage using the formula shown in Figure 32. Sample resistor values for common output voltages are shown in Figure 2. 12 Submit Documentation Feedback VOUT VREF (1) Since the value of VREF is 1.2V, this relationship reduces to: mVV V N(mVRMS) + 27 RMS V OUT(V) (2) for the case of no CNR. Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 An internal 27k resistor in series with the noise reduction pin (NR) forms a low-pass filter for the voltage reference when an external noise reduction capacitor, CNR, is connected from NR to ground. For CNR = 10nF, the total noise in the 10Hz to 100kHz bandwidth is reduced by a factor of ~3.2, giving the approximate relationship: mVV V N(mVRMS) + 8.5 RMS V OUT(V) (3) for CNR = 10nF. This noise reduction effect is shown as RMS Noise Voltage vs CNR in the Typical Characteristics section. The TPS73601 adjustable version does not have the NR pin available. However, connecting a feedback capacitor, CFB, from the output to the feedback pin (FB) reduces output noise and improves load transient performance. The TPS736xx uses an internal charge pump to develop an internal supply voltage sufficient to drive the gate of the NMOS pass element above VOUT. The charge pump generates ~250mV of switching noise at ~4MHz; however, charge-pump noise contribution is negligible at the output of the regulator for most values of IOUT and COUT. BOARD LAYOUT RECOMMENDATION TO IMPROVE PSRR AND NOISE PERFORMANCE To improve ac performance such as PSRR, output noise, and transient response, it is recommended that the board be designed with separate ground planes for VIN and VOUT, with each ground plane connected only at the GND pin of the device. In addition, the ground connection for the bypass capacitor should connect directly to the GND pin of the device. INTERNAL CURRENT LIMIT The TPS736xx internal current limit helps protect the regulator during fault conditions. Foldback current limit helps to protect the regulator from damage during output short-circuit conditions by reducing current limit when VOUT drops below 0.5V. See Figure 12 in the Typical Characteristics section. Note from Figure 12 that approximately -0.2V of VOUT results in a current limit of 0mA. Therefore, if OUT is forced below -0.2V before EN goes high, the device may not start up. In applications that work with both a positive and negative voltage supply, the TPS736xx should be enabled first. Copyright (c) 2003-2010, Texas Instruments Incorporated ENABLE PIN AND SHUTDOWN The enable pin (EN) is active high and is compatible with standard TTL-CMOS levels. A VEN below 0.5V (max) turns the regulator off and drops the GND pin current to approximately 10nA. When EN is used to shutdown the regulator, all charge is removed from the pass transistor gate, and the output ramps back up to a regulated VOUT (see Figure 23). When shutdown capability is not required, EN can be connected to VIN. However, the pass gate may not be discharged using this configuration, and the pass transistor may be left on (enhanced) for a significant time after VIN has been removed. This scenario can result in reverse current flow (if the IN pin is low impedance) and faster ramp times upon power-up. In addition, for VIN ramp times slower than a few milliseconds, the output may overshoot upon power-up. Note that current limit foldback can prevent device start-up under some conditions. See the Internal Current Limit section for more information. DROPOUT VOLTAGE The TPS736xx uses an NMOS pass transistor to achieve extremely low dropout. When (VIN - VOUT) is less than the dropout voltage (VDO), the NMOS pass device is in its linear region of operation and the input-to-output resistance is the RDS-ON of the NMOS pass element. For large step changes in load current, the TPS736xx requires a larger voltage drop from VIN to VOUT to avoid degraded transient response. The boundary of this transient dropout region is approximately twice the dc dropout. Values of VIN - VOUT above this line ensure normal transient response. Operating in the transient dropout region can cause an increase in recovery time. The time required to recover from a load transient is a function of the magnitude of the change in load current rate, the rate of change in load current, and the available headroom (VIN to VOUT voltage drop). Under worst-case conditions [full-scale instantaneous load change with (VIN - VOUT) close to dc dropout levels], the TPS736xx can take a couple of hundred microseconds to return to the specified regulation accuracy. Submit Documentation Feedback 13 TPS736xx SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 www.ti.com TRANSIENT RESPONSE The low open-loop output impedance provided by the NMOS pass element in a voltage follower configuration allows operation without an output capacitor for many applications. As with any regulator, the addition of a capacitor (nominal value 1mF) from the OUT pin to ground will reduce undershoot magnitude but increase its duration. In the adjustable version, the addition of a capacitor, CFB, from the OUT pin to the FB pin will also improve the transient response. The TPS736xx does not have active pull-down when the output is over-voltage. This allows applications that connect higher voltage sources, such as alternate power supplies, to the output. This also results in an output overshoot of several percent if load current quickly drops to zero when a capacitor is connected to the output. The duration of overshoot can be reduced by adding a load resistor. The overshoot decays at a rate determined by output capacitor COUT and the internal/external load resistance. The rate of decay is given by: (Fixed Voltage Version) dVdt + C OUT VOUT 80kW o R LOAD (4) (Adjustable Voltage Version) dVdt + C OUT V OUT 80kW o (R 1 ) R 2) o R LOAD (5) REVERSE CURRENT The NMOS pass element of the TPS736xx provides inherent protection against current flow from the output of the regulator to the input when the gate of the pass device is pulled low. To ensure that all charge is removed from the gate of the pass element, the EN pin must be driven low before the input voltage is removed. If this is not done, the pass element may be left on due to stored charge on the gate. 14 Submit Documentation Feedback After the EN pin is driven low, no bias voltage is needed on any pin for reverse current blocking. Note that reverse current is specified as the current flowing out of the IN pin due to voltage applied on the OUT pin. There will be additional current flowing into the OUT pin due to the 80k internal resistor divider to ground (see Figure 1 and Figure 2). For the TPS73601, reverse current may flow when VFB is more than 1.0V above VIN. THERMAL PROTECTION Thermal protection disables the output when the junction temperature rises to approximately +160C, allowing the device to cool. When the junction temperature cools to approximately +140C, the output circuitry is again enabled. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off. This limits the dissipation of the regulator, protecting it from damage due to overheating. Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate heat sink. For reliable operation, junction temperature should be limited to +125C maximum. To estimate the margin of safety in a complete design (including heat sink), increase the ambient temperature until the thermal protection is triggered; use worst-case loads and signal conditions. For good reliability, thermal protection should trigger at least +35C above the maximum expected ambient condition of your application. This produces a worst-case junction temperature of +125C at the highest expected ambient temperature and worst-case load. The internal protection circuitry of the TPS736xx has been designed to protect against overload conditions. It was not intended to replace proper heat sinking. Continuously running the TPS736xx into thermal shutdown degrades device reliability. Copyright (c) 2003-2010, Texas Instruments Incorporated TPS736xx www.ti.com SBVS038T - SEPTEMBER 2003 - REVISED AUGUST 2010 POWER DISSIPATION The ability to remove heat from the die is different for each package type, presenting different considerations in the PCB layout. The PCB area around the device that is free of other components moves the heat from the device to the ambient air. Performance data for JEDEC low- and high-K boards are shown in the Thermal Information table. Using heavier copper will increase the effectiveness in removing heat from the device. The addition of plated through-holes to heat-dissipating layers will also improve the heat-sink effectiveness. Power dissipation depends on input voltage and load conditions. Power dissipation (PD) is equal to the product of the output current times the voltage drop across the output pass element (VIN to VOUT): space P D + (VIN * VOUT) I OUT (6) Power dissipation can be minimized by using the lowest possible input voltage necessary to assure the required output voltage. PACKAGE MOUNTING Solder pad footprint recommendations for the TPS736xx are presented in Application Bulletin Solder Pad Recommendations for Surface-Mount Devices (SBFA015), available from the Texas Instruments web site at www.ti.com. space REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision S (August, 2009) to Revision T * Page Replaced Dissipation Ratings Table with Thermal Information Table .................................................................................. 3 Changes from Revision R (May, 2008) to Revision S Page * Changed Figure 12 ............................................................................................................................................................... 8 * Added paragraph about recommended start-up sequence to Internal Current Limit section ............................................. 13 * Added paragraph about current foldback and device start-up to Enable Pin and Shutdown section ................................ 13 Copyright (c) 2003-2010, Texas Instruments Incorporated Submit Documentation Feedback 15 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) TPS73601DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73601DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73601DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73601DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73601DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73601DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73601DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73601DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73601DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73601DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS736125DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS736125DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS736125DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS736125DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73615DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73615DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73615DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS73615DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) TPS73615DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73615DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73615DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73615DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73615DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73615DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73616DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73616DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73618DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73618DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73618DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73618DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73618DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73618DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73619DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73619DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73619DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 2 Samples (Requires Login) CU NIPDAU Level-1-260C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS73619DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73625DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73625DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73625DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73625DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73625DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73625DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TPS73630DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73630DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73630DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73630DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73630DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73630DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73630DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73630DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73632DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73632DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73632DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 3 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device (1) 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS73632DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73633DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73633DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73633DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73633DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73633DCQ ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DCQG4 ACTIVE SOT-223 DCQ 6 78 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DCQRG4 ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73633DRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS73643DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73643DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73643DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73643DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM The marketing status values are defined as follows: Addendum-Page 4 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS73601, TPS73615, TPS73618, TPS73625, TPS73630, TPS73632, TPS73633 : * Automotive: TPS73601-Q1 * Enhanced Product: TPS73601-EP, TPS73615-EP, TPS73618-EP, TPS73625-EP, TPS73630-EP, TPS73632-EP, TPS73633-EP NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS73601DBVR Package Package Pins Type Drawing SPQ SOT-23 3000 178.0 DBV 5 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) 9.0 3.23 3.17 1.37 4.0 W Pin1 (mm) Quadrant 8.0 Q3 TPS73601DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73601DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TPS73601DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS73601DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS73601DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS736125DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS736125DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS73615DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73615DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73615DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TPS73615DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS73615DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS73616DBVR SOT-23 DBV 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS73616DBVT SOT-23 DBV 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS73618DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73618DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73618DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS73619DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS73619DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS73625DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73625DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73625DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TPS73630DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73630DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73630DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TPS73632DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73632DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73633DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73633DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73633DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TPS73633DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS73633DRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS73643DBVR SOT-23 DBV 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS73643DBVT SOT-23 DBV 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS73601DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73601DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73601DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS73601DRBR SON DRB 8 3000 370.0 355.0 55.0 TPS73601DRBR SON DRB 8 3000 367.0 367.0 35.0 TPS73601DRBT SON DRB 8 250 220.0 205.0 50.0 TPS736125DRBR SON DRB 8 3000 367.0 367.0 35.0 TPS736125DRBT SON DRB 8 250 210.0 185.0 35.0 TPS73615DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73615DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73615DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS73615DRBR SON DRB 8 3000 367.0 367.0 35.0 TPS73615DRBT SON DRB 8 250 210.0 185.0 35.0 TPS73616DBVR SOT-23 DBV 5 3000 203.0 203.0 35.0 TPS73616DBVT SOT-23 DBV 5 250 203.0 203.0 35.0 TPS73618DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73618DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73618DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS73619DRBR SON DRB 8 3000 370.0 355.0 55.0 TPS73619DRBT SON DRB 8 250 220.0 205.0 50.0 TPS73625DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73625DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73625DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS73630DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73630DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73630DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS73632DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73632DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73633DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73633DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73633DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TPS73633DRBR SON DRB 8 3000 367.0 367.0 35.0 TPS73633DRBT SON DRB 8 250 210.0 185.0 35.0 TPS73643DBVR SOT-23 DBV 5 3000 203.0 203.0 35.0 TPS73643DBVT SOT-23 DBV 5 250 203.0 203.0 35.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated