Data Sheet Low Power, Chip Scale, 10-Bit SD/HD Video Encoder ADV7390/ADV7391/ADV7392/ADV7393 FEATURES 3 high quality, 10-bit video DACs 16x (216 MHz) DAC oversampling for SD 8x (216 MHz) DAC oversampling for ED 4x (297 MHz) DAC oversampling for HD 37 mA maximum DAC output current Multiformat video input support 4:2:2 YCrCb (SD, ED, and HD) 4:4:4 RGB (SD) Multiformat video output support Composite (CVBS) and S-Video (Y-C) Component YPrPb (SD, ED, and HD) Component RGB (SD, ED, and HD) Lead frame chip scale package (LFCSP) options 32-lead, 5 mm x 5 mm LFCSP 40-lead, 6 mm x 6 mm LFCSP Wafer level chip scale package (WLCSP) option 30-ball, 5 x 6 WLCSP with single DAC output Advanced power management Patented content-dependent low power DAC operation Automatic cable detection and DAC power-down Individual DAC on/off control Sleep mode with minimal power consumption 74.25 MHz 8-/10-/16-bit high definition input support Compliant with SMPTE 274M (1080i), 296M (720p), and 240M (1035i) EIA/CEA-861B compliance support NTSC M, PAL B/D/G/H/I/M/N, PAL 60 support NTSC and PAL square pixel operation (24.54 MHz/29.5 MHz) Macrovision Rev 7.1.L1 (SD) and Rev 1.2 (ED) compliant Copy generation management system (CGMS) Closed captioning and wide screen signaling (WSS) Integrated subcarrier locking to external video source Complete on-chip video timing generator On-chip test pattern generation Programmable features Luma and chroma filter responses Vertical blanking interval (VBI) Subcarrier frequency (fSC) and phase Luma delay High definition (HD) programmable features (720p/1080i/1035i) 4x oversampling (297 MHz) Internal test pattern generator Color and black bar, hatch, flat field/frame Fully programmable YCrCb to RGB matrix Rev. J Gamma correction Programmable adaptive filter control Programmable sharpness filter control CGMS (720p/1080i) and CGMS Type B (720p/1080i) Dual data rate (DDR) input support Enhanced definition (ED) programmable features (525p/625p) 8x oversampling (216 MHz output) Internal test pattern generator Black bar, hatch, flat field/frame Individual Y and PrPb output delay Gamma correction Programmable adaptive filter control Fully programmable YCrCb to RGB matrix Undershoot limiter Macrovision Rev 1.2 (525p/625p) (ADV7390/ADV7392 only) CGMS (525p/625p) and CGMS Type B (525p) Dual data rate (DDR) input support Standard definition (SD) programmable features 16x oversampling (216 MHz) Internal test pattern generator Color and black bar Controlled edge rates for start and end of active video Individual Y and PrPb output delay Undershoot limiter Gamma correction Digital noise reduction (DNR) Multiple chroma and luma filters Luma-SSAF filter with programmable gain/attenuation PrPb SSAF Separate pedestal control on component and composite/S-Video output VCR FF/RW sync mode Macrovision Rev 7.1.L1 (ADV7390/ADV7392 only) Copy generation management system (CGMS) Wide screen signaling (WSS) Closed captioning Serial MPU interface with I2C compatibility 2.7 V or 3.3 V analog operation 1.8 V digital operation 1.8 V or 3.3 V I/O operation Temperature range: -40C to +85C W Grade automotive range: -40C to +105C Qualified for automotive applications Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2006-2018 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 ED/HD Timing Reset ................................................................ 51 Revision History ............................................................................... 3 SD Subcarrier Frequency Lock ................................................. 51 Applications ....................................................................................... 5 SD VCR FF/RW Sync ................................................................ 52 General Description ......................................................................... 5 Vertical Blanking Interval ......................................................... 52 Functional Block Diagrams ............................................................. 6 SD Subcarrier Frequency Control ............................................ 52 Specifications..................................................................................... 7 SD Noninterlaced Mode ............................................................ 52 Power Supply Specifications........................................................ 7 SD Square Pixel Mode ............................................................... 53 Input Clock Specifications .......................................................... 7 Filters............................................................................................ 54 Analog Output Specifications ..................................................... 7 ED/HD Test Pattern Color Controls ....................................... 55 Digital Input/Output Specifications--3.3 V ............................. 8 Color Space Conversion Matrix ............................................... 55 Digital Input/Output Specifications--1.8 V ............................. 8 SD Luma and Color Scale Control ........................................... 57 MPU Port Timing Specifications ............................................... 8 SD Hue Adjust Control.............................................................. 57 Digital Timing Specifications--3.3 V ........................................ 9 SD Brightness Detect ................................................................. 57 Digital Timing Specifications--1.8 V ...................................... 10 SD Brightness Control ............................................................... 57 Video Performance Specifications ........................................... 11 SD Input Standard Autodetection ............................................ 58 Power Specifications .................................................................. 11 Double Buffering ........................................................................ 58 Timing Diagrams........................................................................ 12 Programmable DAC Gain Control .......................................... 58 Absolute Maximum Ratings .......................................................... 18 Gamma Correction .................................................................... 59 Thermal Resistance .................................................................... 18 ED/HD Sharpness Filter and Adaptive Filter Controls ......... 60 ESD Caution ................................................................................ 18 ED/HD Sharpness Filter and Adaptive Filter Application Examples ...................................................................................... 61 Pin Configurations and Function Descriptions ......................... 19 Typical Performance Characteristics ........................................... 21 MPU Port Description ................................................................... 26 I2C Operation .............................................................................. 26 Register Map Access ....................................................................... 28 Register Programming ............................................................... 28 Subaddress Register (SR7 to SR0) ............................................ 28 ADV7390/ADV7391 Input Configuration ................................. 46 Standard Definition.................................................................... 46 Enhanced Definition/High Definition .................................... 46 Enhanced Definition (at 54 MHz) ........................................... 46 ADV7392/ADV7393 Input Configuration ................................. 47 Standard Definition.................................................................... 47 Enhanced Definition/High Definition .................................... 48 Enhanced Definition (at 54 MHz) ........................................... 48 Output Configuration .................................................................... 49 Design Features ............................................................................... 50 Output Oversampling ................................................................ 50 HD Interlace External HSYNC and VSYNC Considerations ....................................................................................................... 51 SD Digital Noise Reduction ...................................................... 62 SD Active Video Edge Control ................................................. 64 External Horizontal and Vertical Synchronization Control . 65 Low Power Mode ........................................................................ 66 Cable Detection .......................................................................... 66 DAC Autopower-Down ............................................................. 66 Sleep Mode .................................................................................. 66 Pixel and Control Port Readback ............................................. 67 Reset Mechanisms ...................................................................... 67 SD Teletext Insertion ................................................................. 67 Printed Circuit Board Layout and Design .................................. 69 Unused Pins ................................................................................ 69 DAC Configurations .................................................................. 69 Video Output Buffer and Optional Output Filter .................. 69 Printed Circuit Board (PCB) Layout ....................................... 70 Additional Layout Considerations for the WLCSP Package 71 Typical Applications Circuits .................................................... 72 Copy Generation Management System ....................................... 74 SD CGMS .................................................................................... 74 Rev. J | Page 2 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 ED CGMS.....................................................................................74 SD/ED/HD RGB Output Levels ................................................ 88 HD CGMS ....................................................................................74 SD Output Plots .......................................................................... 89 CGMS CRC Functionality .........................................................74 Video Standards .............................................................................. 90 SD Wide Screen Signaling ..............................................................77 Configuration Scripts ..................................................................... 92 SD Closed Captioning ....................................................................78 Standard Definition .................................................................... 92 Internal Test Pattern Generation ...................................................79 Enhanced Definition .................................................................. 99 SD Test Patterns ...........................................................................79 High Definition .........................................................................101 ED/HD Test Patterns ..................................................................79 SD Timing ........................................................................................80 ADV7390/ADV7391/ADV7392/ADV7393 Evaluation Board .........................................................................................................104 HD Timing .......................................................................................85 Outline Dimensions ......................................................................105 Video Output Levels .......................................................................86 Ordering Guide .........................................................................107 SD YPrPb Output Levels--SMPTE/EBU N10 ........................86 Automotive Products ................................................................107 ED/HD YPrPb Output Levels ...................................................87 REVISION HISTORY 8/2018--Rev. I to Rev. J Changes to Figure 93 ......................................................................72 Changes to Figure 94 ......................................................................73 Updated Outline Dimensions ......................................................105 Changes to Ordering Guide .........................................................107 2/2015--Rev. H to Rev. I Changed ADV739x to ADV7390/ADV7391/ADV7392/ ADV7393 ............................................................................. Universal Changes to Figure 19 ......................................................................19 Changes to Table 15 ........................................................................20 Changes to Figure 144 ..................................................................104 Updated Outline Dimensions ......................................................106 Changes to Ordering Guide .........................................................107 9/2014--Rev. G to Rev. H Changed Storage Temperature Range from -60C to +100C to -60C to +150C; Table 13 .............................................................18 Updated Figure 145, Outline Dimensions .................................105 Changes to Ordering Guide .........................................................107 2/2013--Rev. F to Rev. G Change to Features Section .............................................................. 1 Changes to Table 14 ........................................................................18 Changes to Figure 62 ......................................................................48 Changes to Ordering Guide .........................................................107 11/2012--Rev. E to Rev. F Updated Outline Dimensions ......................................................105 Changes to Ordering Guide .........................................................107 2/2012--Rev. D to Rev. E Changes to Table 1 ............................................................................ 5 Changes to Digital Input/Output Specifications-- 1.8 V Section ...................................................................................... 8 Changes to Table 15 ........................................................................ 21 Changes to Table 20 ........................................................................ 31 Changes to Table 23 ........................................................................ 34 Changes to Table 28 ........................................................................ 39 Changes to 16-Bit 4:4:4 RGB Mode Section ................................ 47 Added External Sync Polarity Section.......................................... 51 Deleted ED/HD Nonstandard Timing Mode Section, Figure 63, and Table 41, Renumbered Sequentially ...................................... 51 Changed SD Subcarrier Frequency Lock, Subcarrier Phase Reset, and Timing Reset Section to SD Subcarrier Frequency Lock Section..................................................................................... 52 Deleted Subaddress 0x84, Bits[2:1] Section, Timing Reset (TR) Mode Section, Subcarrier Phase Reset (SCR) Mode Section, Figure 64, and Figure 65 ................................................................. 52 Changes to Ordering Guide ......................................................... 121 11/2011--Rev. C to Rev. D Changes to Features Section ............................................................ 1 Updated Outline Dimensions and changes to Automotive Products Section............................................................................ 107 9/2011--Rev. B to Rev. C Changes to MPU Port Description Section ................................. 26 Changes to Ordering Guide ......................................................... 107 7/2010--Rev. A to Rev. B Changes to Features Section ............................................................ 1 Change to Applications Section ...................................................... 5 Changes to General Description ..................................................... 5 Added Table 2, Renumbered Subsequent Tables .......................... 5 Added Figure 2, Renumbered Subsequent Figures ...................... 6 Changes to Full-Drive Output Current Parameter, Table 5 ........ 7 Changes to Table 14 ........................................................................ 18 Added Figure 20 .............................................................................. 19 Changes to Table 15 ........................................................................ 19 Rev. J | Page 3 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Changes to ADV7390/ADV7391 Input Configuration Section .............................................................................................. 45 Added Additional Layout Considerations for the WLCSP Package Section ............................................................................... 71 Added Figure 97.............................................................................. 73 Changes to Configuration Scripts Section .................................. 92 Changes to Subaddress 0x00, Table 66 ........................................ 93 Changes to Subaddress 0x00, Table 80 ........................................ 95 Changes to Subaddress 0x00, Table 83 ........................................ 95 Changes to Subaddress 0x00, Table 97 ........................................ 98 Updated Outline Dimensions, Added Figure 150.................... 106 Changes to Ordering Guide ........................................................ 106 3/2009--Rev. 0 to Rev. A Changes to Features Section............................................................ 1 Deleted Detailed Features Section, Changes to Table 1............... 4 Changes to Figure 1, Added Figure 2 ............................................. 5 Changes to Table 2, Input Clock Specifications Section, and Analog Output Specifications Section ........................................... 6 Changes to Digital Input/Output Specifications--3.3 V Section and Table 5 ......................................................................................... 7 Added Digital Input/Output Specifications--1.8 V Section and Table 6 ................................................................................................ 7 Changes to MPU Port Timing Specifications Section, Default Conditions ........................................................................... 7 Changes to Digital Timing Specifications--3.3 V Section and Table 8 ................................................................................................ 8 Added Digital Timing Specifications--1.8 V Section and Table 9 ................................................................................................ 9 Added Video Performance Specifications Section, Default Conditions ....................................................................................... 10 Added Power Specifications Section, Default Conditions ........ 10 Changes to Table 11 ........................................................................ 10 Changes to Figure 16 ...................................................................... 16 Changes to Table 12 ........................................................................ 17 Changes to Table 14, Pin 19 and Pin 1 Descriptions ................. 18 Changes to MPU Port Description Section ................................ 25 Data Sheet Changes to I2C Operation Section ............................................... 25 Added Table 15 ............................................................................... 25 Changes to Table 17 ....................................................................... 28 Changes to Table 19, 0x30 Bit Description ................................. 30 Changes to Table 27 ....................................................................... 37 Changes to Table 29, 0x8B Bit Description ................................. 39 Changes to Table 30 ....................................................................... 40 Changes to Table 31 ....................................................................... 41 Added Table 32 ............................................................................... 42 Renamed Features Section to Design Features Section ............. 48 Changes to ED/HD Nonstandard Timing Mode Section ......... 48 Added the HD Interlace External HSYNC and VSYNC Considerations Section .................................................................. 49 Changes to SD Subcarrier Frequency Lock, Subcarrier Reset, and Timing Reset Section.............................................................. 49 Changes to Subaddress 0x8C to Subaddress 0x8F Section ....... 51 Changes to Programming the FSC Section................................... 51 Changes to Subaddress 0x82, Bit 4 Section ................................. 51 Added SD Manual CSC Matrix Adjust Feature Section ............ 54 Added Table 47 ............................................................................... 55 Changes to Subaddress 0x9C to Subaddress 0x9F Section ....... 56 Changes to Subaddress 0xBA Section.......................................... 56 Added Sleep Mode Section ........................................................... 65 Changes to Pixel and Control Port Readback Section .............. 66 Changes to Reset Mechanisms Section ....................................... 66 Added SD Teletext Insertion Section ........................................... 66 Added Figure 87 ............................................................................. 67 Added Figure 88 ............................................................................. 68 Changes to DAC Configuration Section ..................................... 68 Added Unused Pins Section .......................................................... 68 Changes to Power Supply Sequencing Section ........................... 70 Changes to Internal Test Pattern Generation Section ............... 77 Changes to SD Timing, Mode 0 (CCIR-656)--Slave Option (Subaddress 0x8A = XXXXX000) Section .................................. 78 10/2006--Revision 0: Initial Version Rev. J | Page 4 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 APPLICATIONS Table 1. Standards Directly Supported by the LFCSP Packages Mobile handsets Digital still cameras Portable media and DVD players Portable game consoles Digital camcorders Set-top box (STB) Automotive infotainment (ADV7392 and ADV7393 only) Active Resolution 720 x 240 720 x 288 720 x 480 GENERAL DESCRIPTION The ADV7390/ADV7391/ADV7392/ADV7393 are a family of high speed, digital-to-analog video encoders on single monolithic chips. Three 2.7 V/3.3 V, 10-bit video DACs (a single DAC for the WLCSP package) provide support for composite (CVBS), S-Video (Y-C), or component (YPrPb/RGB) analog outputs in either standard definition (SD) or high definition (HD) video formats. The single DAC WLCSP package supports CVBS (NTSC and PAL) output only in SD resolution (see Table 2). Optimized for low power operation, occupying a minimal footprint, and requiring few external components, these encoders are ideally suited to portable and power-sensitive applications requiring TV-out functionality. Cable detection and DAC auto power-down features ensure that power consumption is kept to a minimum. The ADV7390/ADV7391 have an 8-bit video input port that supports SD video formats over an SDR interface and HD video formats over a DDR interface. The ADV7392/ADV7393 have a 16-bit video input port that can be configured in a variety of ways. SD RGB input is supported. All members of the family support embedded EAV/SAV timing codes, external video synchronization signals, and the I2C(R) and communication protocol. Table 1 and Table 2 list the video standards directly supported by the ADV7390/ADV7391/ ADV7392/ADV7393 family. I/P1 P P I Frame Rate (Hz) 59.94 50 29.97 Clock Input (MHz) 27 27 27 720 x 576 I 25 27 640 x 480 I 29.97 24.54 768 x 576 I 25 29.5 720 x 483 720 x 483 720 x 483 720 x 576 720 x 483 720 x 576 1920 x 1035 1920 x 1035 1280 x 720 P P P P P P I I P 27 27 27 27 27 27 74.25 74.1758 74.25 1280 x 720 P 74.1758 SMPTE 296M 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 I I P P 74.25 74.1758 74.25 74.1758 SMPTE 274M SMPTE 274M SMPTE 274M SMPTE 274M 1920 x 1080 P 59.94 59.94 59.94 50 59.94 50 30 29.97 60, 50, 30, 25, 24 23.97, 59.94, 29.97 30, 25 29.97 30, 25, 24 23.98, 29.97 24 ITU-R BT.601/656 ITU-R BT.601/656 NTSC square pixel PAL square pixel SMPTE 293M BTA T-1004 ITU-R BT.1358 ITU-R BT.1358 ITU-R BT.1362 ITU-R BT.1362 SMPTE 240M SMPTE 240M SMPTE 296M 74.25 ITU-R BT.709-5 1 Standard I = interlaced, P = progressive. Table 2. Standards Directly Supported by the WLCSP Package Active Resolution 720 x 480 I/P 1 I Frame Rate (Hz) 29.97 Clock Input (MHz) 27 720 x 576 I 25 27 640 x 480 I 29.97 24.54 768 x 576 I 25 29.5 1 I = interlaced, P = progressive. Rev. J | Page 5 of 107 Standard ITU-R BT.601/656 ITU-R BT.601/656 NTSC Square Pixel PAL Square Pixel ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet FUNCTIONAL BLOCK DIAGRAMS VBI DATA SERVICE INSERTION ALSB ADV7390/ADV7391 MPU PORT SUBCARRIER FREQUENCY LOCK (SFL) VDD_IO 8-BIT SD OR 8-BIT ED/HD SDR/DDR SD/ED/HD INPUT 4:2:2 TO 4:4:4 DEINTERLEAVE ADD SYNC PROGRAMMABLE LUMINANCE FILTER ADD BURST PROGRAMMABLE CHROMINANCE FILTER 16x FILTER YCrCb TO RGB 16x FILTER SIN/COS DDS BLOCK ASYNC BYPASS YCrCb POWER MANAGEMENT CONTROL YCbCr TO RGB MATRIX PROGRAMMABLE ED/HD FILTERS HDTV TEST PATTERN GENERATOR HSYNC CLKIN DAC 1 11-BIT DAC 2 DAC 2 11-BIT DAC 3 DAC 3 REFERENCE AND CABLE DETECT 16x/4x OVERSAMPLING PLL VSYNC 11-BIT DAC 1 4x FILTER SHARPNESS AND ADAPTIVE FILTER CONTROL VIDEO TIMING GENERATOR RESET VAA AGND SFL PGND EXT_LF PVDD RSET 06234-001 GND_IO SDA SCL MULTIPLEXER VDD (2) DGND (2) COMP Figure 1. ADV7390/ADV7391 (32-Lead LFCSP) SCL VBI DATA SERVICE INSERTION SDA ALSB ADV7390BCBZ MPU PORT SUBCARRIER FREQUENCY LOCK (SFL) VDD_IO 8-BIT SD SDR/DDR SD INPUT 4:2:2 TO 4:4:4 DEINTERLEAVE POWER MANAGEMENT CONTROL RESET ADD SYNC PROGRAMMABLE LUMINANCE FILTER ADD BURST PROGRAMMABLE CHROMINANCE FILTER 16x FILTER 16x FILTER SIN/COS DDS BLOCK VIDEO TIMING GENERATOR HSYNC VAA AGND SFL CLKIN PVDD DAC 1 REFERENCE AND CABLE DETECT 16x OVERSAMPLING PLL VSYNC 11-BIT DAC 1 PGND EXT_LF RSET 06234-146 GND_IO VDD (2) MULTIPLEXER DGND (2) COMP Figure 2. ADV7390BCBZ-A (30-Ball WLCSP) SCL SDA ALSB SDR/DDR SD/ED/HD INPUT 4:2:2 TO 4:4:4 DEINTERLEAVE AGND MPU PORT RGB TO YCrCb MATRIX SUBCARRIER FREQUENCY LOCK (SFL) ADD SYNC PROGRAMMABLE LUMINANCE FILTER YCrCb TO RGB ADD BURST PROGRAMMABLE CHROMINANCE FILTER SIN/COS DDS BLOCK 16x FILTER 16x FILTER ASYNC BYPASS YCrCb HDTV TEST PATTERN GENERATOR POWER MANAGEMENT CONTROL RESET VAA ADV7392/ADV7393 VBI DATA SERVICE INSERTION VDD_IO 8-/10-/16-BIT SD OR 8-/10-/16-BIT ED/HD SFL PROGRAMMABLE ED/HD FILTERS YCbCr TO RGB MATRIX HSYNC VSYNC 16x/4x OVERSAMPLING PLL CLKIN PVDD Figure 3. ADV7392/ADV7393 (40-Lead LFCSP) Rev. J | Page 6 of 107 DAC 1 12-BIT DAC 2 DAC 2 12-BIT DAC 3 DAC 3 4x FILTER SHARPNESS AND ADAPTIVE FILTER CONTROL VIDEO TIMING GENERATOR 12-BIT DAC 1 PGND EXT_LF REFERENCE AND CABLE DETECT COMP RSET 06234-145 GND_IO VDD (2) MULTIPLEXER DGND (2) Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 SPECIFICATIONS POWER SUPPLY SPECIFICATIONS All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 3. Parameter SUPPLY VOLTAGES VDD VDD_IO PVDD VAA POWER SUPPLY REJECTION RATIO Min Typ Max Unit 1.71 1.71 1.71 2.6 1.8 3.3 1.8 3.3 0.002 1.89 3.63 1.89 3.465 V V V V %/% INPUT CLOCK SPECIFICATIONS VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 1.71 V to 3.63 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 4. Parameter fCLKIN Conditions 1 SD/ED ED (at 54 MHz) HD Min CLKIN High Time, t9 CLKIN Low Time, t10 CLKIN Peak-to-Peak Jitter Tolerance 1 Typ 27 54 74.25 Max 40 40 2 Unit MHz MHz MHz % of one clock cycle % of one clock cycle ns SD = standard definition, ED = enhanced definition (525p/625p), HD = high definition. ANALOG OUTPUT SPECIFICATIONS VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 1.71 V to 3.63 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 5. Parameter Full-Drive Output Current Low-Drive Output Current DAC-to-DAC Matching Output Compliance, VOC Output Capacitance, COUT Analog Output Delay 2 DAC Analog Output Skew 1 2 Conditions RSET = 510 , RL = 37.5 All DACs enabled RSET = 510 , RL = 37.5 DAC 1 enabled only 1 RSET = 4.12 k, RL = 300 DAC 1, DAC 2, DAC 3 Min 33 Typ 34.6 Max 37 Unit mA 31.5 33.5 37 mA 4.3 2.0 0 DAC 1, DAC 2, DAC 3 1.4 10 6 1 The recommended method of bringing this value back to the ideal value is by adjusting Register 0x0B to the recommended value of 0x12. Output delay measured from the 50% point of the rising edge of the input clock to the 50% point of the DAC output full-scale transition. Rev. J | Page 7 of 107 mA % V pF ns ns ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet DIGITAL INPUT/OUTPUT SPECIFICATIONS--3.3 V VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 6. Parameter Input High Voltage, VIH Input Low Voltage, VIL Input Leakage Current, IIN Input Capacitance, CIN Output High Voltage, VOH Output Low Voltage, VOL Three-State Leakage Current Three-State Output Capacitance Conditions Min 2.0 Typ Max 0.8 10 VIN = VDD_IO 4 ISOURCE = 400 A ISINK = 3.2 mA VIN = 0.4 V, 2.4 V 2.4 0.4 1 4 Unit V V A pF V V A pF DIGITAL INPUT/OUTPUT SPECIFICATIONS--1.8 V When VDD_IO is set to 1.8 V, all the digital video inputs and control inputs, such as I2C, HS, and VS, should use 1.8 V levels. VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 1.71 V to 1.89 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 7. Parameter Input High Voltage, VIH Input Low Voltage, VIL Input Capacitance, CIN Output High Voltage, VOH Output Low Voltage, VOL Three-State Output Capacitance Conditions Min 0.7 VDD_IO Typ Max 0.3 VDD_IO 4 ISOURCE = 400 A ISINK = 3.2 mA VDD_IO - 0.4 0.4 4 Unit V V pF V V pF MPU PORT TIMING SPECIFICATIONS VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 1.71 V to 3.63 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 8. Parameter MPU PORT, I2C MODE 1 SCL Frequency SCL High Pulse Width, t1 SCL Low Pulse Width, t2 Hold Time (Start Condition), t3 Setup Time (Start Condition), t4 Data Setup Time, t5 SDA, SCL Rise Time, t6 SDA, SCL Fall Time, t7 Setup Time (Stop Condition), t8 1 Conditions See Figure 17 Min 0 0.6 1.3 0.6 0.6 100 Typ Max Unit 400 kHz s s s s ns ns ns s 300 300 0.6 Guaranteed by characterization. Rev. J | Page 8 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 DIGITAL TIMING SPECIFICATIONS--3.3 V VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 2.97 V to 3.63 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 9. Parameter VIDEO DATA AND VIDEO CONTROL PORT 2, 3 Data Input Setup Time, t11 4 Data Input Hold Time, t124 Control Input Setup Time, t114 Control Input Hold Time, t124 Control Output Access Time, t134 Control Output Hold Time, t144 PIPELINE DELAY 5 SD1 CVBS/Y-C Outputs (2x) CVBS/Y-C Outputs (8x) CVBS/Y-C Outputs (16x) Component Outputs (2x) Component Outputs (8x) Component Outputs (16x) ED1 Component Outputs (1x) Component Outputs (4x) Component Outputs (8x) HD1 Component Outputs (1x) Component Outputs (2x) Component Outputs (4x) RESET CONTROL RESET Low Time Conditions 1 Min SD ED/HD-SDR ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR or ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR or ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR, ED/HD-DDR, or ED (at 54 MHz) SD ED/HD-SDR, ED/HD-DDR, or ED (at 54 MHz) 2.1 2.3 2.3 1.7 1.0 1.1 1.1 1.0 2.1 2.3 1.7 1.0 1.1 1.0 Typ Max 12 10 4.0 3.5 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SD oversampling disabled SD oversampling enabled SD oversampling enabled SD oversampling disabled SD oversampling enabled SD oversampling enabled 68 79 67 78 69 84 Clock cycles Clock cycles Clock cycles Clock cycles Clock cycles Clock cycles ED oversampling disabled ED oversampling enabled ED oversampling enabled 41 49 46 Clock cycles Clock cycles Clock cycles HD oversampling disabled HD oversampling enabled HD oversampling enabled 40 42 44 Clock cycles Clock cycles Clock cycles 100 SD = standard definition, ED = enhanced definition (525p/625p), HD = high definition, SDR = single data rate, DDR = dual data rate. Video data: P[15:0] for ADV7392/ADV7393 or P[7:0] for ADV7390/ADV7391. 3 Video control: HSYNC and VSYNC. 4 Guaranteed by characterization. 5 Guaranteed by design. 1 2 Rev. J | Page 9 of 107 ns ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet DIGITAL TIMING SPECIFICATIONS--1.8 V VDD = 1.71 V to 1.89 V, PVDD = 1.71 V to 1.89 V, VAA = 2.6 V to 3.465 V, VDD_IO = 1.71 V to 1.89 V. All specifications TMIN to TMAX (-40C to +85C), unless otherwise noted. Table 10. Parameter VIDEO DATA AND VIDEO CONTROL PORT 2, 3 Data Input Setup Time, t11 4 Data Input Hold Time, t124 Control Input Setup Time, t114 Control Input Hold Time, t124 Control Output Access Time, t134 Control Output Hold Time, t144 PIPELINE DELAY 5 SD1 CVBS/Y-C Outputs (2x) CVBS/Y-C Outputs (8x) CVBS/Y-C Outputs (16x) Component Outputs (2x) Component Outputs (8x) Component Outputs (16x) ED1 Component Outputs (1x) Component Outputs (4x) Component Outputs (8x) HD1 Component Outputs (1x) Component Outputs (2x) Component Outputs (4x) RESET CONTROL RESET Low Time Conditions 1 Min SD ED/HD-SDR ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR or ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR or ED/HD-DDR ED (at 54 MHz) SD ED/HD-SDR, ED/HD-DDR, or ED (at 54 MHz) SD ED/HD-SDR, ED/HD-DDR, or ED (at 54 MHz) 1.4 1.9 1.9 1.6 1.4 1.5 1.5 1.3 1.4 1.2 1.0 1.4 1.0 1.0 Typ Max 13 12 4.0 5.0 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns SD oversampling disabled SD oversampling enabled SD oversampling enabled SD oversampling disabled SD oversampling enabled SD oversampling enabled 68 79 67 78 69 84 Clock cycles Clock cycles Clock cycles Clock cycles Clock cycles Clock cycles ED oversampling disabled ED oversampling enabled ED oversampling enabled 41 49 46 Clock cycles Clock cycles Clock cycles HD oversampling disabled HD oversampling enabled HD oversampling enabled 40 42 44 Clock cycles Clock cycles Clock cycles 100 SD = standard definition, ED = enhanced definition (525p/625p), HD = high definition, SDR = single data rate, DDR = dual data rate. Video data: P[15:0] for ADV7392/ADV7393 or P[7:0] for ADV7390/ADV7391. 3 Video control: HSYNC and VSYNC. 4 Guaranteed by characterization. 5 Guaranteed by design. 1 2 Rev. J | Page 10 of 107 ns Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 VIDEO PERFORMANCE SPECIFICATIONS VDD = 1.8 V, PVDD = 1.8 V, VAA = 3.3 V, VDD_IO = 3.3 V, TA = +25C. Table 11. Parameter STATIC PERFORMANCE Resolution Integral Nonlinearity (INL) 1 Differential Nonlinearity (DNL)1, 2 STANDARD DEFINTION (SD) MODE Luminance Nonlinearity Differential Gain Differential Phase Signal-to-Noise Ratio (SNR) 3 Conditions Min Typ Max Unit RSET = 510 , RL = 37.5 RSET = 510 , RL = 37.5 10 0.5 0.5 Bits LSBs LSBs NTSC NTSC Luma ramp Flat field full bandwidth 0.5 0.5 0.6 58 75 % % Degrees dB dB 12.5 5.8 MHz MHz 30.0 13.75 MHz MHz ENHANCED DEFINITION (ED) MODE Luma Bandwidth Chroma Bandwidth HIGH DEFINITION (HD) MODE Luma Bandwidth Chroma Bandwidth Measured on DAC 1, DAC 2, and DAC 3. Differential nonlinearity (DNL) measures the deviation of the actual DAC output voltage step from the ideal. For +ve DNL, the actual step value lies above the ideal step value. For -ve DNL, the actual step value lies below the ideal step value. 3 Measured on the ADV7392/ADV7393 operating in 10-bit input mode. 1 2 POWER SPECIFICATIONS VDD = 1.8 V, PVDD = 1.8 V, VAA = 3.3 V, VDD_IO = 3.3 V, TA = +25C. Table 12. Parameter NORMAL POWER MODE 1, 2 IDD 3 IDD_IO IAA 5 Conditions Min SD (16x oversampling enabled), CVBS (only one DAC turned on) SD (16x oversampling enabled), YPrPb (three DACs turned on) ED (8x oversampling enabled) 4 HD (4x oversampling enabled)4 One DAC enabled All DACs enabled IPLL SLEEP MODE IDD IAA IDD_IO IPLL Typ 33 68 59 81 1 50 122 4 5 0.3 0.2 0.1 RSET = 510 (all DACs operating in full-drive mode). 75% color bar test pattern applied to pixel data pins. IDD is the continuous current required to drive the digital core. 4 Applicable to both single data rate (SDR) and dual data rate (DDR) input modes. 5 IAA is the total current required to supply all DACs. 1 2 3 Rev. J | Page 11 of 107 Max Unit 101 10 mA mA mA mA mA mA mA mA 151 10 A A A A ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet TIMING DIAGRAMS * t13 = control output access time * t14 = control output hold time In addition, see Table 35 for the ADV7390/ADV7391 pixel port input configuration and Table 36 for the ADV7392/ADV7393 pixel port input configuration. The following abbreviations are used in Figure 4 to Figure 11: t9 = clock high time t10 = clock low time t11 = data setup time t12 = data hold time CLKIN t9 CONTROL INPUTS t12 t10 HSYNC IN SLAVE MODE VSYNC PIXEL PORT Y0 Cb0 Y1 Cr0 t11 Y2 Cb2 Cr2 t13 CONTROL OUTPUTS 06234-002 IN MASTER/SLAVE MODE t14 Figure 4. SD Input, 8-/10-Bit 4:2:2 YCrCb, Input Mode 000 CLKIN t9 CONTROL INPUTS t12 t10 HSYNC IN SLAVE MODE VSYNC PIXEL PORT Y0 Y1 Y2 Y3 PIXEL PORT Cb0 Cr0 Cb2 Cr2 t11 t13 CONTROL OUTPUTS IN MASTER/SLAVE MODE t14 Figure 5. SD Input, 16-Bit 4:2:2 YCrCb, Input Mode 000 Rev. J | Page 12 of 107 06234-003 * * * * Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 CLKIN t9 CONTROL INPUTS t12 t10 HSYNC VSYNC PIXEL PORT G0 G1 G2 PIXEL PORT B0 B1 B2 R1 R2 t11 R0 PIXEL PORT CONTROL OUTPUTS 06234-004 t14 t13 Figure 6. SD Input, 16-Bit 4:4:4 RGB, Input Mode 000 CLKIN t9 CONTROL INPUTS t12 t10 HSYNC VSYNC PIXEL PORT Y0 Y1 Y2 Y3 Y4 Y5 PIXEL PORT Cb0 Cr0 Cb2 Cr2 Cb4 Cr4 t11 t13 06234-005 CONTROL OUTPUTS t14 Figure 7. ED/HD-SDR Input, 16-Bit 4:2:2 YCrCb, Input Mode 001 CLKIN* t9 CONTROL INPUTS t10 HSYNC VSYNC PIXEL PORT Cb0 t11 Y0 Cr0 Y1 t12 Cb2 Y2 Cr2 t12 t11 t13 t14 *LUMA/CHROMA CLOCK RELATIONSHIP CAN BE INVERTED USING SUBADDRESS 0x01, BITS 1 AND 2. Figure 8. ED/HD-DDR Input, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC), Input Mode 010 Rev. J | Page 13 of 107 06234-006 CONTROL OUTPUTS ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet CLKIN* t9 PIXEL PORT 3FF t11 t10 00 00 XY t12 Cb0 Y0 Cr0 Y1 t12 t11 t13 t14 *LUMA/CHROMA CLOCK RELATIONSHIP CAN BE INVERTED USING SUBADDRESS 0x01, BITS 1 AND 2. 06234-007 CONTROL OUTPUTS Figure 9. ED/HD-DDR Input, 8-/10-Bit 4:2:2 YCrCb (EAV/SAV), Input Mode 010 CLKIN t10 t9 CONTROL INPUTS HSYNC VSYNC Cb0 PIXEL PORT Y0 Cr0 Y1 Cr2 Y2 t13 t12 t11 Cb2 06234-008 t14 CONTROL OUTPUTS Figure 10. ED (at 54 MHz) Input, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC), Input Mode 111 CLKIN t9 PIXEL PORT 3FF t12 t11 t10 00 00 XY Cb0 Y0 Cr0 Y1 t13 06234-009 t14 CONTROL OUTPUTS Figure 11. ED (at 54 MHz) Input, 8-/10-Bit 4:2:2 YCrCb (EAV/SAV), Input Mode 111 Rev. J | Page 14 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Y OUTPUT b HSYNC VSYNC PIXEL PORT Y0 Y1 Y2 Y3 PIXEL PORT* Cb0 Cr0 Cb2 Cr2 a a = AS PER RELEVANT STANDARD. 06234-010 b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING SPECIFICATION SECTION OF THE DATA SHEET. A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A SYNC FALLING EDGE ON THE OUTPUT AFTER A TIME EQUAL TO THE PIPELINE DELAY. Figure 12. ED-SDR, 16-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram Y OUTPUT b HSYNC VSYNC Cb0 PIXEL PORT Y0 Cr0 Y1 a b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING SPECIFICATION SECTION OF THE DATA SHEET. A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A SYNC FALLING EDGE ON THE OUTPUT AFTER A TIME EQUAL TO THE PIPELINE DELAY. Figure 13. ED-DDR, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram Rev. J | Page 15 of 107 06234-011 a(MIN) = 244 CLOCK CYCLES FOR 525p. a(MIN) = 264 CLOCK CYCLES FOR 625p. ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Y OUTPUT b HSYNC VSYNC PIXEL PORT Y0 Y1 Y2 Y3 PIXEL PORT Cb0 Cr0 Cb2 Cr2 a a = AS PER RELEVANT STANDARD. 06234-012 b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING SPECIFICATION SECTION OF THE DATA SHEET. A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A FALLING EDGE OF TRI-LEVEL SYNC ON THE OUTPUT AFTER A TIME EQUAL TO THE PIPELINE DELAY. Figure 14. HD-SDR, 16-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram Y OUTPUT b HSYNC VSYNC PIXEL PORT Cb0 Y0 Cr0 Y1 a b = PIPELINE DELAY. PLEASE REFER TO RELEVANT PIPELINE DELAY. THIS CAN BE FOUND IN THE DIGITAL TIMING SPECIFICATION SECTION OF THE DATA SHEET. A FALLING EDGE OF HSYNC INTO THE ENCODER GENERATES A FALLING EDGE OF TRI-LEVEL SYNC ON THE OUTPUT AFTER A TIME EQUAL TO THE PIPELINE DELAY. Figure 15. HD-DDR, 8-/10-Bit 4:2:2 YCrCb (HSYNC/VSYNC) Input Timing Diagram Rev. J | Page 16 of 107 06234-013 a = AS PER RELEVANT STANDARD. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 HSYNC VSYNC Cr PAL = 264 CLOCK CYCLES NTSC = 244 CLOCK CYCLES Figure 16. SD Input Timing Diagram (Timing Mode 1) t3 t5 t3 SDA t1 SCL t2 t7 t4 t8 2C Mode) Figure 17. MPU Port Timing Diagram (I Rev. J | Page 17 of 107 06234-015 t6 Y 06234-014 Y Cb PIXEL PORT ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 13. Parameter VAA to AGND VDD to DGND PVDD to PGND VDD_IO to GND_IO AGND to DGND AGND to PGND AGND to GND_IO DGND to PGND DGND to GND_IO PGND to GND_IO Digital Input Voltage to GND_IO Analog Outputs to AGND Max CLKIN Input Frequency Storage Temperature Range (tS) Junction Temperature (tJ) Lead Temperature (Soldering, 10 sec) 1 1 Rating -0.3 V to +3.9 V -0.3 V to +2.3 V -0.3 V to +2.3 V -0.3 V to +3.9 V -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to VDD_IO + 0.3 V -0.3 V to VAA 80 MHz -60C to +150C 150C 260C Analog output short circuit to any power supply or common can be of an indefinite duration. Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. JA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 14. Thermal Resistance1 Package Type 30-Ball WLCSP 32-Lead LFCSP 40-Lead LFCSP JA2 35 27 26 JC-TOP3 1 32 32 JC-BOTTOM4 N/A 1.2 1 Unit C/W C/W C/W Values are based on a JEDEC 4-layer test board. With the exposed metal paddle on the underside of the LFCSP soldered to the PCB ground. 3 This is the thermal resistance of the junction to the top of the package. 4 This is the thermal resistance of the junction to the bottom of the package. 1 2 The ADV7390/ADV7391/ADV7392/ADV7393 are RoHScompliant, Pb-free products. The lead finish is 100% pure Sn electroplate. The device is suitable for Pb-free applications up to 255C (5C) IR reflow (JEDEC STD-20). The ADV7390/ADV7391/ADV7392/ADV7393 are backward compatible with conventional SnPb soldering processes. The electroplated Sn coating can be soldered with SnPb solder pastes at conventional reflow temperatures of 220C to 235C. ESD CAUTION Rev. J | Page 18 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 GND_IO P1 P0 DGND VDD HSYNC VSYNC SFL PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS 32 31 30 29 28 27 26 25 BALL A1 CORNER 1 2 3 4 5 6 7 8 PIN 1 INDICATOR ADV7390/ ADV7391 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 RSET COMP DAC 1 DAC 2 DAC 3 VAA AGND PVDD 2 3 4 5 A RSET HSYNC VDD P0 VDD_IO B DAC1 VSYNC SFL P1 P2 C VAA COMP DGND P3 P4 D AGND GND_IO RESET VDD DGND E PVDD EXT_LF ALSB P5 P6 F PGND SDA SCL CLKIN P7 TOP VIEW (BALL SIDE DOWN) Not to Scale 06234-147 NOTES 1. THE EXPOSED PAD SHOULD BE CONNECTED TO ANALOG GROUND (AGND). 06234-017 P7 ALSB SDA SCL CLKIN RESET PGND EXT_LF 9 10 11 12 13 14 15 16 VDD_IO P2 P3 P4 VDD DGND P5 P6 1 Figure 20. ADV7390BCBZ-A Pin Configuration 40 39 38 37 36 35 34 33 32 31 GND_IO P3 P2 P1 DGND VDD P0 HSYNC VSYNC SFL Figure 18. ADV7390/ADV7391 Pin Configuration ADV7392/ ADV7393 TOP VIEW (Not to Scale) 30 29 28 27 26 25 24 23 22 21 RSET COMP DAC 1 DAC 2 DAC 3 VAA AGND PVDD EXT_LF PGND NOTES 1. THE EXPOSED PAD SHOULD BE CONNECTED TO ANALOG GROUND (AGND). 06234-018 P11 ALSB SDA SCL P12 P13 P14 P15 CLKIN RESET 11 12 13 14 15 16 17 18 19 20 VDD_IO 1 P4 2 P5 3 P6 4 P7 5 VDD 6 DGND 7 P8 8 P9 9 P10 10 Figure 19. ADV7392/ADV7393 Pin Configuration Table 15. Pin Function Descriptions ADV7390/ ADV7391 9 to 7, 4 to 2, 31, 30 N/A Pin No. 1 ADV7392/ ADV7393 N/A Mnemonic P7 to P0 Input/ Output I P15 to P0 I F4 CLKIN I ADV7390 WLCSP F5, E5, E4, C5, C4, B5, B4, A4 N/A 13 18 to 15, 11 to 8, 5 to 2, 39 to 37, 34 19 27 33 A2 HSYNC I/O 26 32 B2 VSYNC I/O 25 31 B3 SFL I/O Rev. J | Page 19 of 107 Description 8-Bit Pixel Port (P7 to P0). P0 is the LSB. See Table 35 for input modes (ADV7390/ADV7391). 16-Bit Pixel Port (P15 to P0). P0 is the LSB. See Table 36 for input modes (ADV7392/ADV7393). Pixel Clock Input for HD (74.25 MHz), ED 2 (27 MHz or 54 MHz), or SD (27 MHz). Horizontal Synchronization Signal. This pin can also be configured to output an SD, ED, or HD horizontal synchronization signal. See the External Horizontal and Vertical Synchronization Control section. Vertical Synchronization Signal. This pin can also be configured to output an SD, ED, or HD vertical synchronization signal. See the External Horizontal and Vertical Synchronization Control section. Subcarrier Frequency Lock (SFL) Input. ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet ADV7390/ ADV7391 24 Pin No. 1 ADV7392/ ADV7393 30 ADV7390 WLCSP A1 Mnemonic RSET Input/ Output I 23 29 C2 COMP O N/A 22, 21, 20 N/A 28, 27, 26 B1 N/A O O 12 11 10 14 14 13 12 20 F3 F2 E3 D3 DAC 1 DAC 1, DAC 2, DAC 3 SCL SDA ALSB RESET I I/O I I 19 5, 28 25 6, 35 C1 A3, D4 VAA VDD P P 1 17 1 23 A5 E1 VDD_IO PVDD P P 16 15 18 6, 29 32 22 21 24 7, 36 40 E2 F1 D1 C3, D5 D2 EXT_LF PGND AGND DGND GND_IO EPAD I G G G G G 1 2 3 Description Controls the amplitudes of the DAC 1, DAC 2, and DAC 3 outputs. For full-drive operation (for example, into a 37.5 load), a 510 resistor must be connected from RSET to AGND. For low-drive operation (for example, into a 300 load), a 4.12 k resistor must be connected from RSET to AGND. Compensation Pin. Connect a 2.2 nF capacitor from COMP to VAA. DAC Output. Full-drive and low-drive capable DAC DAC Outputs. Full-drive and low-drive capable DACs. I2C Clock Input. I2C Data Input/Output. ALSB sets up the LSB 3 of the MPU I2C address. Resets the on-chip timing generator and sets the ADV7390/ADV7391/ADV7392/ADV7393 into its default mode. Analog Power Supply (2.7 V or 3.3 V). Digital Power Supply (1.8 V). For dual-supply configurations, VDD can be connected to other 1.8 V supplies through a ferrite bead or suitable filtering. Input/Output Digital Power Supply (1.8 V or 3.3 V). PLL Power Supply (1.8 V). For dual-supply configurations, PVDD can be connected to other 1.8 V supplies through a ferrite bead or suitable filtering. External Loop Filter for the Internal PLL. PLL Ground Pin. Analog Ground Pin. Digital Ground Pin. Input/Output Supply Ground Pin. Exposed Pad. Connect to analog ground (AGND). N/A means not applicable. ED = enhanced definition = 525p and 625p. LSB = least significant bit. In the ADV7390/ADV7392, setting the LSB to 0 sets the I2C address to 0xD4. Setting it to 1 sets the I2C address to 0xD6. In the ADV7391/ADV7393, setting the LSB to 0 sets the I2C address to 0x54. Setting it to 1 sets the I2C address to 0x56. Rev. J | Page 20 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 TYPICAL PERFORMANCE CHARACTERISTICS ED Pr/Pb RESPONSE. LINEAR INTERP FROM 4:2:2 TO 4:4:4 Y RESPONSE IN ED 8x OVERSAMPLING MODE 1.0 0 0.5 -10 0 -0.5 GAIN (dB) -40 -1.0 -50 -1.5 -60 -2.0 -70 -2.5 -80 0 20 40 60 80 100 120 140 FREQUENCY (MHz) 160 180 200 -3.0 Figure 21. ED 8x Oversampling, PrPb Filter (Linear) Response 0 2 4 6 8 FREQUENCY (MHz) 10 06234-022 -30 06234-019 GAIN (dB) -20 12 Figure 24. ED 8x Oversampling, Y Filter Response (Focus on Pass Band) ED Pr/Pb RESPONSE. SSAF INTERP FROM 4:2:2 TO 4:4:4 HD Pr/Pb RESPONSE. SSAF INTERP FROM 4:2:2 TO 4:4:4 10 0 0 -10 -10 -20 -30 -30 GAIN (dB) GAIN (dB) -20 -40 -40 -50 -60 -50 -70 -60 -80 -70 0 20 40 60 80 100 120 140 FREQUENCY (MHz) 160 180 200 -100 0 18.5 37.0 74.0 92.5 55.5 FREQUENCY (MHz) 111.0 129.5 148.0 06234-023 -90 06234-020 -80 Figure 25. HD 4x Oversampling, PrPb (SSAF) Filter Response (4:2:2 Input) Figure 22. ED 8x Oversampling, PrPb Filter (SSAFTM) Response HD Pr/Pb RESPONSE. 4:4:4 INPUT MODE Y RESPONSE IN ED 8x OVERSAMPLING MODE 0 0 -10 -10 -20 -30 GAIN (dB) -30 -40 -50 -50 -60 -80 0 20 40 60 80 100 120 140 FREQUENCY (MHz) 160 180 200 -100 10 20 30 40 50 60 70 80 90 100 110 120 130 140 FREQUENCY (MHz) Figure 26. HD 4x Oversampling, PrPb (SSAF) Filter Response (4:4:4 Input) Figure 23. ED 8x Oversampling, Y Filter Response Rev. J | Page 21 of 107 06234-024 -90 -70 -80 -40 -70 -60 06234-021 GAIN (dB) -20 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Y RESPONSE IN HD 4x OVERSAMPLING MODE 10 0 0 -10 -10 MAGNITUDE (dB) -20 GAIN (dB) -30 -40 -50 -60 -20 -30 -40 -50 -70 -80 -60 -70 0 18.5 37.0 55.5 74.0 92.5 FREQUENCY (MHz) 111.0 129.5 148.0 0 06234-025 -100 2 4 6 8 FREQUENCY (MHz) 10 12 06234-028 -90 Figure 30. SD PAL, Luma Low-Pass Filter Response Figure 27. HD 4x Oversampling, Y Filter Response Y PASS BAND IN HD 4x OVERSAMPLING MODE 3.0 0 1.5 -10 0 MAGNITUDE (dB) GAIN (dB) -1.5 -3.0 -4.5 -6.0 -7.5 -20 -30 -40 -50 -9.0 -60 0 0 -10 -10 -20 -20 MAGNITUDE (dB) 0 -30 -40 -60 -60 2 4 6 8 FREQUENCY (MHz) 10 12 12 -40 -50 0 10 -30 -50 -70 4 6 8 FREQUENCY (MHz) Figure 31. SD NTSC, Luma Notch Filter Response 06234-027 MAGNITUDE (dB) Figure 28. HD 4x Oversampling, Y Filter Response (Focus on Pass Band) 2 Figure 29. SD NTSC, Luma Low-Pass Filter Response -70 0 2 4 6 8 FREQUENCY (MHz) 10 Figure 32. SD PAL, Luma Notch Filter Response Rev. J | Page 22 of 107 12 06234-030 FREQUENCY (MHz) -70 06234-026 -12.0 27.750 30.063 32.375 34.688 37.000 39.312 41.625 43.937 46.250 06234-029 -10.5 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Y RESPONSE IN SD OVERSAMPLING MODE 5 0 4 -10 MAGNITUDE (dB) GAIN (dB) -20 -30 -40 -50 -60 3 2 1 0 -1 0 20 40 60 80 100 120 140 FREQUENCY (MHz) 160 180 0 06234-031 -80 200 3 4 FREQUENCY (MHz) 2 1 5 7 6 06234-034 -70 Figure 36. SD Luma SSAF Filter, Programmable Gain Figure 33. SD 16x Oversampling, Y Filter Response 1 0 0 -20 MAGNITUDE (dB) MAGNITUDE (dB) -10 -30 -40 -1 -2 -3 -50 2 0 10 4 6 8 FREQUENCY (MHz) 12 -5 06234-032 -70 0 5 7 6 Figure 37. SD Luma SSAF Filter, Programmable Attenuation Figure 34. SD Luma SSAF Filter Response up to 12 MHz 4 0 2 -10 MAGNITUDE (dB) 0 -2 -4 -6 -20 -30 -40 -50 -8 -12 0 1 2 3 4 FREQUENCY (MHz) 5 6 7 -70 0 2 4 8 6 FREQUENCY (MHz) 10 Figure 38. SD Luma CIF Low-Pass Filter Response Figure 35. SD Luma SSAF Filter, Programmable Responses Rev. J | Page 23 of 107 12 06234-036 -60 -10 06234-033 MAGNITUDE (dB) 3 4 FREQUENCY (MHz) 2 1 06234-035 -4 -60 Data Sheet 0 -10 -10 -20 -20 -30 -40 -50 -60 -60 2 4 8 6 FREQUENCY (MHz) 10 12 -70 0 Figure 39. SD Luma QCIF Low-Pass Filter Response -10 -10 -20 -20 MAGNITUDE (dB) 0 -30 -40 -60 -60 10 12 12 -70 06234-038 -70 8 6 FREQUENCY (MHz) 10 -40 -50 4 8 6 FREQUENCY (MHz) -30 -50 2 4 Figure 42. SD Chroma 1.3 MHz Low-Pass Filter Response 0 0 2 0 2 4 8 6 FREQUENCY (MHz) 10 Figure 43. SD Chroma 1.0 MHz Low-Pass Filter Response 0 0 -10 -10 -20 -20 MAGNITUDE (dB) Figure 40. SD Chroma 3.0 MHz Low-Pass Filter Response -30 -40 -50 12 06234-041 0 -30 -40 -50 -60 -70 0 2 4 8 6 FREQUENCY (MHz) 10 12 Figure 41. SD Chroma 2.0 MHz Low-Pass Filter Response -70 0 2 4 8 6 FREQUENCY (MHz) 10 Figure 44. SD Chroma 0.65 MHz Low-Pass Filter Response Rev. J | Page 24 of 107 12 06234-042 -60 06234-039 MAGNITUDE (dB) -40 -50 -70 MAGNITUDE (dB) -30 06234-040 MAGNITUDE (dB) 0 06234-037 MAGNITUDE (dB) ADV7390/ADV7391/ADV7392/ADV7393 ADV7390/ADV7391/ADV7392/ADV7393 0 -10 -10 -20 -20 -30 -40 -30 -40 -50 -50 -60 -60 -70 0 2 4 8 6 FREQUENCY (MHz) 10 12 Figure 45. SD Chroma CIF Low-Pass Filter Response -70 0 2 4 8 6 FREQUENCY (MHz) 10 Figure 46. SD Chroma QCIF Low-Pass Filter Response Rev. J | Page 25 of 107 12 06234-044 MAGNITUDE (dB) 0 06234-043 MAGNITUDE (dB) Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet MPU PORT DESCRIPTION Devices such as a microprocessor can communicate with the ADV7390/ADV7391/ADV7392/ADV7393 through a 2-wire serial (I2C-compatible) bus. After power-up or reset, the MPU port is configured for I2C operation. I2C OPERATION The ADV7390/ADV7391/ADV7392/ADV7393 support a 2-wire serial (I2C-compatible) microprocessor bus driving multiple peripherals. This port operates in an open-drain configuration. Two wires, serial data (SDA) and serial clock (SCL), carry information between any device connected to the bus and the ADV7390/ADV7391/ADV7392/ADV7393. The slave address depends on the device (ADV7390, ADV7391, ADV7392, or ADV7393), the operation (read or write), and the state of the ALSB pin (0 or 1). See Table 16, Figure 47, and Figure 48. The LSB sets either a read or a write operation. Logic 1 corresponds to a read operation, and Logic 0 corresponds to a write operation. A1 is controlled by setting the ALSB pin of the ADV7390/ ADV7391/ADV7392/ADV7393 to Logic 0 or Logic 1. Table 16. ADV7390/ADV7391/ADV7392/ADV7393 I2C Slave Addresses Device ALSB 0 0 1 1 0 0 1 1 ADV7390 and ADV7392 ADV7391 and ADV7393 1 1 0 1 Operation Write Read Write Read Write Read Write Read Slave Address 0xD4 0xD5 0xD6 0xD7 0x54 0x55 0x56 0x57 0 X 1 A1 ADDRESS CONTROL SET UP BY ALSB 0 1 WRITE READ 06234-045 READ/WRITE CONTROL Figure 47. ADV7390/ADV7392 I2C Slave Address The various devices on the bus use the following protocol. The master initiates a data transfer by establishing a start condition, defined by a high-to-low transition on SDA while SCL remains high. This indicates that an address/data stream follows. All peripherals respond to the start condition and shift the next eight bits (7-bit address plus the R/W bit). The bits are transferred from MSB down to LSB. The peripheral that recognizes the transmitted address responds by pulling the data line low during the ninth clock pulse. This is known as an acknowledge bit. All other devices withdraw from the bus at this point and maintain an idle condition. The idle condition occurs when the device monitors the SDA and SCL lines waiting for the start condition and the correct transmitted address. The R/W bit determines the direction of the data. Logic 0 on the LSB of the first byte means that the master writes information to the peripheral. Logic 1 on the LSB of the first byte means that the master reads information from the peripheral. The ADV7390/ADV7391/ADV7392/ADV7393 act as a standard slave device on the bus. The data on the SDA pin is eight bits long, supporting the 7-bit addresses plus the R/W bit. It interprets the first byte as the device address and the second byte as the starting subaddress. There is a subaddress auto-increment facility. This allows data to be written to or read from registers in ascending subaddress sequence starting at any valid subaddress. A data transfer is always terminated by a stop condition. The user can also access any unique subaddress register on a oneby-one basis without updating all the registers. Stop and start conditions can be detected at any stage during the data transfer. If these conditions are asserted out of sequence with normal read and write operations, they cause an immediate jump to the idle condition. During a given SCL high period, the user should issue only a start condition, a stop condition, or a stop condition followed by a start condition. If an invalid subaddress is issued by the user, the ADV7390/ADV7391/ ADV7392/ADV7393 do not issue an acknowledge but returns to the idle condition. If the user uses the auto-increment method of addressing the encoder and exceeds the highest subaddress, the following actions are taken: * 1 0 1 0 1 A1 X ADDRESS CONTROL * SET UP BY ALSB READ/WRITE CONTROL 0 1 WRITE READ Figure 48. ADV7391/ADV7393 I C Slave Address 2 06234-046 0 In read mode, the highest subaddress register contents are output until the master device issues a no acknowledge. This indicates the end of a read. A no acknowledge condition occurs when the SDA line is not pulled low on the ninth pulse. In write mode, the data for the invalid byte is not loaded into any subaddress register, a no acknowledge is issued by the ADV7390/ADV7391/ADV7392/ADV7393, and the part returns to the idle condition. Figure 49 shows an example of data transfer for a write sequence and the start and stop conditions. Figure 50 shows bus write and read sequences. Rev. J | Page 26 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 SCL S 9 1-7 8 START ADDR R/W ACK 9 1-7 8 SUBADDRESS ACK 1-7 DATA 8 9 ACK P STOP 06234-047 SDA Figure 49. I2C Data Transfer S SLAVE ADDR A(S) SUBADDR A(S) DATA S SLAVE ADDR S = START BIT P = STOP BIT A(S) A(S) P LSB = 1 LSB = 0 READ SEQUENCE DATA A(S) SUBADDR A(S) S SLAVE ADDR A(S) = ACKNOWLEDGE BY SLAVE A(M) = ACKNOWLEDGE BY MASTER A(S) DATA A(M) A (S) = NO-ACKNOWLEDGE BY SLAVE A (M) = NO-ACKNOWLEDGE BY MASTER Figure 50. I2C Read and Write Sequence Rev. J | Page 27 of 107 DATA A(M) P 06234-048 WRITE SEQUENCE ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet REGISTER MAP ACCESS A microprocessor can read from or write to all registers of the ADV7390/ADV7391/ADV7392/ADV7393 via the MPU port, except for registers that are specified as read-only or write-only registers. REGISTER PROGRAMMING The subaddress register determines the register accessed by the next read or write operation. All communication through the MPU port starts with an access to the subaddress register. A read/write operation is then performed from/to the target address, incrementing to the next address until the transaction is complete. SUBADDRESS REGISTER (SR7 TO SR0) Table 17 to Table 34 describe the functionality of each register. All registers can be read from as well as written to, unless otherwise stated. The subaddress register is an 8-bit write-only register. After the MPU port is accessed and a read/write operation is selected, the subaddress is set up. The subaddress register determines which register performs the next operation. Table 17. Register 0x00 SR7 to SR0 0x00 Register Power mode Bit Description Sleep mode. With this control enabled, the current consumption is reduced to A level. All DACs and the internal PLL circuit are disabled. Registers can be read from and written to in sleep mode. 7 6 Bit Number 5 4 3 2 0 0 1 PLL and oversampling control. This control allows the internal PLL circuit to be powered down and the oversampling to be switched off. 0 1 DAC 3: power on/off. 0 1 DAC 2: power on/off. 0 1 DAC 1: power on/off. 0 1 Reserved. 1 0 0 Register Setting Sleep mode off Sleep mode on PLL on PLL off DAC 3 off DAC 3 on DAC 2 off DAC 2 on DAC 1 off DAC 1 on Reset Value 0x12 0 Table 18. Register 0x01 to Register 0x09 SR7 to SR0 0x01 Register Mode select Bit Description Reserved. DDR clock edge alignment (used only for ED 2 and HD DDR modes) 7 Reserved Input mode (see Subaddress 0x30, Bits[7:3] for ED/HD standard selection) Reserved 6 Bit Number 1 5 4 3 2 1 0 0 0 1 1 1 0 1 0 0 Register Setting Chroma clocked in on rising clock edge and luma clocked in on falling clock edge. Reserved. Reserved. Luma clocked in on rising clock edge and chroma clocked in on falling clock edge. 0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 Rev. J | Page 28 of 107 SD input. ED/HD-SDR input. 3 ED/HD-DDR input. Reserved. Reserved. Reserved. Reserved. ED (at 54 MHz) input. Reset Value 0x00 Data Sheet SR7 to SR0 0x02 Register Mode Register 0 ADV7390/ADV7391/ADV7392/ADV7393 Bit Description Reserved HD interlace external VSYNC and HSYNC 7 6 Bit Number 1 5 4 3 2 0 1 Manual CSC matrix adjust 0 1 Sync on RGB 0 1 RGB/YPrPb output select 0 1 SD sync output enable 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0 1 0 1 Register Setting Zero must be written to this bit. Default. If using HD HSYNC/VSYNCinterlace mode, setting this bit to 1 is recommended (see the HD Interlace External HSYNC and VSYNC Considerations section for more information). Disabled. Enabled. Disable manual CSC matrix adjust. Enable manual CSC matrix adjust. No sync. Sync on all RGB outputs. RGB component outputs. YPrPb component outputs. No sync output. Output SD syncs on HSYNC and VSYNC pins. No sync output. Output ED/HD syncs on HSYNC and VSYNC pins. ED/HD CSC Matrix 0 ED/HD CSC Matrix 1 ED/HD CSC Matrix 2 ED/HD CSC Matrix 3 ED/HD CSC Matrix 4 ED/HD CSC Matrix 5 ED/HD CSC Matrix 6 0 0 0 1 Test pattern black bar 4 ED/HD sync output enable 1 Reset Value 0x20 x x LSBs for GY. 0x03 x x 0xF0 0x4E x x x x x x x x x x x x LSBs for RV. LSBs for BU. LSBs for GV. LSBs for GU. Bits[9:2] for GY. x x x x x x x x Bits[9:2] for GU. 0x0E x x x x x x x x Bits[9:2] for GV. 0x24 x x x x x x x x Bits[9:2] for BU. 0x92 x x x x x x x x Bits[9:2] for RV. 0x7C x x x = Logic 0 or Logic 1. ED = enhanced definition = 525p and 625p. 3 Available on the ADV7392/ADV7393 (40-pin devices) only. 4 Subaddress 0x31, Bit 2 must also be enabled (ED/HD). Subaddress 0x84, Bit 6 must also be enabled (SD). 1 2 Rev. J | Page 29 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 19. Register 0x0B to Register 0x17 SR7 to SR0 0x0B Register DAC 1, DAC 2, DAC 3 output levels Bit Description Positive gain to DAC output voltage Negative gain to DAC output voltage 0x0D DAC power mode 7 0 0 0 ... 0 0 1 1 1 ... 1 6 0 0 0 ... 0 1 1 1 0 ... 1 Bit Number 1 5 4 3 2 0 0 0 0 0 0 0 0 0 0 0 0 ... ... ... ... 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ... ... ... ... 1 1 1 1 1 0 0 1 ... 1 0 0 0 1 ... 1 DAC 1 low power mode 0 0 1 0 ... 1 0 0 1 0 ... 1 0 1 DAC 2 low power mode 0 1 DAC 3 low power mode 0 1 SD/ED oversample rate select 0x10 Cable detection 0 1 Reserved DAC 1 cable detect 0 0 0 Read only DAC 2 cable detect 1 0 1 0 0x13 0x14 0x16 Pixel Port Readback A 2 Pixel Port Readback B2 Control port readback2 0 Software reset 2 0x00 DAC autopower-down disable. DAC autopower-down enable. 0 x 0 x x x x x x Read only. 0xXX x x x x x x x x Read only. 0xXX x x x Read only. 0xXX P[15:8] readback (ADV7392/ADV7393) P[7:0] readback (ADV7392/ADV7393) Reserved VSYNC readback SFL readback Reserved Reserved Software reset Reserved. 1 Cable detected on DAC 1. DAC 1 unconnected. Cable detected on DAC 2. DAC 2 unconnected. 0 x x x HSYNC readback 0x17 0x00 0 1 Reserved P[7:0] readback (ADV7390/ADV7391) Reset Value 0x00 0 0 Read only Reserved Unconnected DAC autopower-down Register Setting 0%. +0.018%. +0.036%. ... +7.382%. +7.5%. -7.5%. -7.382%. -7.364%. ... -0.018%. DAC 1 low power disabled. DAC 1 low power enabled. DAC 2 low power disabled. DAC 2 low power enabled. DAC 3 low power disabled. DAC 3 low power enabled. SD = 16x, ED = 8x. SD = 8x, ED = 4x. x x x 0 0 1 0 0 0 x = Logic 0 or Logic 1. For correct operation, Subaddress 0x01[6:4] must equal the default value of 000. Rev. J | Page 30 of 107 0 0 0 0x00 Writing a 1 resets the device; this is a selfclearing bit. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 20. Register 0x30 SR7 to SR0 0x30 Register ED/HD Mode Register 1 Bit Description ED/HD output standard 7 6 Bit Number 5 4 3 2 ED/HD input synchronization format 1 0 0 0 0 1 1 0 1 1 0 1 ED/HD standard 2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 0 0 0 0 1 0 1 0 0 0 0 1 1 1 1 0 1 0 0 1 1 0 0 0 0 0 1 0 1 0 1 0 0 0 0 1 1 1 0 1 1 1 0 0 1 0 1 0 0 1 1 1 1 1 1 0 1 1 1 0 0 0 0 0 0 0 1 1 1 2 0 0 1 0 10011 to 11111 Register Setting EIA-770.2 output EIA-770.3 output EIA-770.1 output Output levels for full input range Reserved External HSYNC, VSYNC and field inputs 1 Embedded EAV/SAV codes SMPTE 293M, ITU-BT.1358 BTA-1004, ITU-BT.1362 ITU-BT.1358 ITU-BT.1362 SMPTE 296M-1, SMPTE 274M-2 SMPTE 296M-3 SMPTE 296M-4, SMPTE 274M-5 SMPTE 296M-6 SMPTE 296M-7, SMPTE 296M-8 SMPTE 240M Reserved Reserved SMPTE 274M-4, SMPTE 274M-5 SMPTE 274M-6 SMPTE 274M-7, SMPTE 274M-8 SMPTE 274M-9 SMPTE 274M-10, SMPTE 274M-11 ITU-R BT.709-5 Reserved Note ED HD 525p at 59.94 Hz 525p at 59.94 Hz 625p at 50 Hz 625p at 50 Hz 720p at 60 Hz/59.94 Hz 720p at 50 Hz 720p at 30 Hz/29.97 Hz 720p at 25 Hz 720p at 24 Hz/23.98 Hz 1035i at 60 Hz/59.94 Hz 1080i at 30 Hz/29.97 Hz 1080i at 25 Hz 1080p at 30 Hz/29.97 Hz 1080p at 25 Hz 1080p at 24 Hz/23.98 Hz 1080Psf at 24 Hz Synchronization can be controlled with a combination of either HSYNC and VSYNC inputs or HSYNC and field inputs, depending on Subaddress 0x34, Bit 6. See the HD Interlace External HSYNC and VSYNC Considerations section for more information. Rev. J | Page 31 of 107 Reset Value 0x00 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 21. Register 0x31 to Register 0x33 SR7 to SR0 0x31 Register ED/HD Mode Register 2 Bit Number 7 6 5 4 Bit Description ED/HD pixel data valid 3 2 HD oversample rate select 0 1 ED/HD test pattern hatch/field 0 1 ED/HD vertical blanking interval (VBI) open 0 1 ED/HD undershoot limiter 0 0 1 1 ED/HD sharpness filter ED/HD Mode Register 3 ED/HD Y delay with respect to the falling edge of HSYNC 0 0 0 0 1 0 0 0 0 1 ED/HD CGMS enable 0 0 1 1 0 0 1 ED/HD Cr/Cb sequence 0 1 0 0 1 Sinc compensation filter on DAC 1, DAC 2, DAC 3 0 1 Reserved ED/HD chroma SSAF filter Reserved ED/HD double buffering 0 1 0 1 0 0 1 0 1 0 Reserved ED/HD input format 1 0 0 1 1 0 0 1 ED/HD CGMS CRC enable ED/HD Mode Register 4 0 1 0 1 0 1 ED/HD color delay with respect to the falling edge of HSYNC 0x33 0 0 1 0 1 ED/HD test pattern enable 0x32 1 0 0 1 1 0 1 Available on the ADV7392/ADV7393 (40-pin devices) only. Rev. J | Page 32 of 107 Register Setting Pixel data valid off. Pixel data valid on. 4x. 2x. HD test pattern off. HD test pattern on. Hatch. Field/frame. Disabled. Enabled. Disabled. -11 IRE. -6 IRE. -1.5 IRE. Disabled. Enabled. 0 clock cycles. One clock cycle. Two clock cycles. Three clock cycles. Four clock cycles. 0 clock cycles. One clock cycle. Two clock cycles. Three clock cycles. Four clock cycles. Disabled. Enabled. Disabled. Enabled. Cb after falling edge of HSYNC. Cr after falling edge of HSYNC. 0 must be written to this bit. 8-bit input. 10-bit input 1. Disabled. Enabled. 0 must be written to this bit. Disabled. Enabled. 1 must be written to this bit. Disabled. Enabled. Reset Value 0x00 0x00 0x68 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 22. Register 0x34 to Register 0x38 SR7 to SR0 0x34 Register ED/HD Mode Register 5 Bit Description ED/HD timing reset 7 6 Bit Number 1 5 4 3 2 0 1 ED/HD VSYNC control2 Reserved ED Macrovision(R) enable 3 0 0 1 0 = Field input. 1 = VSYNC input. Update field/line counter. Field/line counter free running. 0 1 0 0 1 0 1 ED/HD gamma correction curve select 0 1 ED/HD gamma correction enable 0 1 ED/HD adaptive filter mode ED/HD Y level 5 ED/HD Cr level5 ED/HD Cb level5 ED/HD Test Pattern Y level ED/HD Test Pattern Cr level ED/HD Test Pattern Cb level 0x00 0 ED/HD color DAC swap 0x36 0x37 0x38 ED Macrovision disabled. ED Macrovision enabled. 0 must be written to this bit. Reserved Reserved ED/HD sync on PrPb ED/HD adaptive filter enable Reset Value 0x48 1 ED/HD VSYNC input/field input ED/HD Mode Register 6 Register Setting Internal ED/HD timing counters enabled. Resets the internal ED/HD timing counters. HSYNC output control (see Table 55). VSYNC output control (see Table 56). 0 1 Reserved 0x35 0 0 1 0 1 ED/HD HSYNC control 2 ED/HD horizontal/vertical counter mode 4 1 0 1 0 1 x x x x x x x x x x x x x x x x x x x x x x x x Disabled. Enabled. DAC 2 = Pb, DAC 3 = Pr. DAC 2 = Pr, DAC 3 = Pb. Gamma Correction Curve A. Gamma Correction Curve B. Disabled. Enabled. Mode A. Mode B. Disabled. Enabled. Y level value. Cr level value. Cb level value. x = Logic 0 or Logic 1. Used in conjunction with ED/HD sync output enable in Subaddress 0x02, Bit 7 = 1. 3 Applies to the ADV7390 and ADV7392 only. 4 When set to 0, the horizontal/vertical counters automatically wrap around at the end of the line/field/frame of the selected standard. When set to 1, the horizontal/vertical counters are free running and wrap around when external sync signals indicate to do so. 5 For use with ED/HD internal test patterns only (Subaddress 0x31, Bit 2 = 1). 1 2 Rev. J | Page 33 of 107 0xA0 0x80 0x80 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 23. Register 0x39 to Register 0x43 SR7 to SR0 0x39 0X3A Register ED/HD Mode Register 7 ED/HD Mode Register 8 Bit Description Reserved ED/HD EIA/CEA-861B synchronization compliance 7 Reserved INV_PHSYNC_POL 0 6 5 Bit Number 4 3 0 0 2 0 0x41 0x42 0x43 ED/HD CGMS Data 0 ED/HD CGMS Data 1 ED/HD CGMS Data 2 Register Setting Reset Value 0x00 Disabled Enabled 0 0 1 Disabled Enabled Disabled Enabled Disabled Enabled 0x00 0x00 0 1 INV_PBLANK_POL ED/HD sharpness filter gain 0 0 0 1 INV_PVSYNC_POL 0x40 1 0 0 1 Reserved ED/HD sharpness filter gain Value A 0 0 0 ED/HD sharpness filter gain Value B ED/HD CGMS data bits 0 0 ... 0 1 ... 1 0 0 0 ... 1 0 ... 1 0 0 0 ... 1 0 ... 1 0 ED/HD CGMS data bits C15 C14 ED/HD CGMS data bits C7 C6 0 0 0 0 ... 0 1 ... 1 0 0 ... 1 0 ... 1 0 0 ... 1 0 ... 0 1 ... 1 0 ... 1 0 1 ... 1 0 ... 1 0 C19 C18 C17 C16 C13 C12 C11 C10 C9 C8 Gain A = 0 Gain A = +1 ... Gain A = +7 Gain A = -8 ... Gain A = -1 Gain B = 0 Gain B = +1 ... Gain B = +7 Gain B = -8 ... Gain B = -1 CGMS C19 to C1 6 CGMS C15 to C8 C5 C4 C3 C2 C1 C0 CGMS C7 to C0 Rev. J | Page 34 of 107 0x00 0x00 0x00 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 24. Register 0x44 to Register 0x57 SR7 to SR0 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 1 Register ED/HD Gamma A0 ED/HD Gamma A1 ED/HD Gamma A2 ED/HD Gamma A3 ED/HD Gamma A4 ED/HD Gamma A5 ED/HD Gamma A6 ED/HD Gamma A7 ED/HD Gamma A8 ED/HD Gamma A9 ED/HD Gamma B0 ED/HD Gamma B1 ED/HD Gamma B2 ED/HD Gamma B3 ED/HD Gamma B4 ED/HD Gamma B5 ED/HD Gamma B6 ED/HD Gamma B7 ED/HD Gamma B8 ED/HD Gamma B9 Bit Description ED/HD Gamma Curve A (Point 24) ED/HD Gamma Curve A (Point 32) ED/HD Gamma Curve A (Point 48) ED/HD Gamma Curve A (Point 64) ED/HD Gamma Curve A (Point 80) ED/HD Gamma Curve A (Point 96) ED/HD Gamma Curve A (Point 128) ED/HD Gamma Curve A (Point 160) ED/HD Gamma Curve A (Point 192) ED/HD Gamma Curve A (Point 224) ED/HD Gamma Curve B (Point 24) ED/HD Gamma Curve B (Point 32) ED/HD Gamma Curve B (Point 48) ED/HD Gamma Curve B (Point 64) ED/HD Gamma Curve B (Point 80) ED/HD Gamma Curve B (Point 96) ED/HD Gamma Curve B (Point 128) ED/HD Gamma Curve B (Point 160) ED/HD Gamma Curve B (Point 192) ED/HD Gamma Curve B (Point 224) 7 x x x x x x x x x x x x x x x x x x x x 6 x x x x x x x x x x x x x x x x x x x x x = Logic 0 or Logic 1. Rev. J | Page 35 of 107 5 x x x x x x x x x x x x x x x x x x x x Bit Number 1 4 3 2 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 1 x x x x x x x x x x x x x x x x x x x x 0 x x x x x x x x x x x x x x x x x x x x Register Setting A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 Reset Value 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 25. Register 0x58 to Register 0x5D SR7 to SR0 0x58 0x59 Register ED/HD Adaptive Filter Gain 1 ED/HD Adaptive Filter Gain 2 ED/HD Adaptive Filter Threshold A 0 0 ... 0 1 ... 1 x 0 0 ... 1 0 ... 1 x Bit Number 1 5 4 3 2 0 0 0 0 ... ... 0 1 1 0 ... ... 1 1 0 0 0 1 ... ... 1 1 0 0 ... ... 1 1 0 0 0 0 ... ... 0 1 1 0 ... ... 1 1 0 0 0 1 ... ... 1 1 0 0 ... ... 1 1 0 0 0 0 ... ... 0 1 1 0 ... ... 1 1 0 0 0 1 ... ... 1 1 0 0 ... ... 1 1 x x x x ED/HD Adaptive Filter Threshold B x x x x x x x x Threshold B 0x00 ED/HD Adaptive Filter Threshold C x x x x x x x x Threshold C 0x00 Bit Description ED/HD Adaptive Filter Gain 1, Value A 7 6 ED/HD Adaptive Filter Gain 1, Value B 0 0 ... 0 1 ... 1 0 0 ... 1 0 ... 1 ED/HD Adaptive Filter Gain 2, Value A ED/HD Adaptive Filter Gain 2, Value B 0x5A ED/HD Adaptive Filter Gain 3 0x5C 0x5D 1 ED/HD Adaptive Filter Threshold A ED/HD Adaptive Filter Threshold B ED/HD Adaptive Filter Threshold C 0 0 ... 1 0 ... 1 ED/HD Adaptive Filter Gain 3, Value A ED/HD Adaptive Filter Gain 3, Value B 0x5B 0 0 ... 0 1 ... 1 x = Logic 0 or Logic 1. Rev. J | Page 36 of 107 Reset Value 0x00 x Register Setting Gain A = 0 Gain A = +1 ... Gain A = +7 Gain A = -8 ... Gain A = -1 Gain B = 0 Gain B = +1 ... Gain B = +7 Gain B = -8 ... Gain B = -1 Gain A = 0 Gain A = +1 ... Gain A = +7 Gain A = -8 ... Gain A = -1 Gain B = 0 Gain B = +1 ... Gain B = +7 Gain B = -8 ... Gain B = -1 Gain A = 0 Gain A = +1 ... Gain A = +7 Gain A = -8 ... Gain A = -1 Gain B = 0 Gain B = +1 ... Gain B = +7 Gain B = -8 ... Gain B = -1 Threshold A 1 0 0 ... 1 0 ... 1 0 0 1 ... 1 0 ... 1 0 0 ... 1 0 ... 1 0 1 ... 1 0 ... 1 0 0 ... 1 0 ... 1 0 1 ... 1 0 ... 1 x 0x00 0x00 0x00 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 26. Register 0x5E to Register 0x6E SR7 to SR0 0x5E Register ED/HD CGMS Type B Register 0 Bit Description ED/HD CGMS Type B enable 7 6 5 Bit Number 4 3 2 ED/HD CGMS Type B CRC enable 0x5F 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E ED/HD CGMS Type B Register 1 ED/HD CGMS Type B Register 2 ED/HD CGMS Type B Register 3 ED/HD CGMS Type B Register 4 ED/HD CGMS Type B Register 5 ED/HD CGMS Type B Register 6 ED/HD CGMS Type B Register 7 ED/HD CGMS Type B Register 8 ED/HD CGMS Type B Register 9 ED/HD CGMS Type B Register 10 ED/HD CGMS Type B Register 11 ED/HD CGMS Type B Register 12 ED/HD CGMS Type B Register 13 ED/HD CGMS Type B Register 14 ED/HD CGMS Type B Register 15 ED/HD CGMS Type B Register 16 ED/HD CGMS Type B header bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits ED/HD CGMS Type B data bits 1 0 0 1 0 1 Register Setting Disabled Enabled Disabled Enabled H5 to H0 Reset Value 0x00 H5 H4 H3 H2 H1 H0 P7 P6 P5 P4 P3 P2 P1 P0 P7 to P0 0x00 P15 P14 P13 P12 P11 P10 P9 P8 P15 to P8 0x00 P23 P22 P21 P20 P19 P18 P17 P16 P23 to P16 0x00 P31 P30 P29 P28 P27 P26 P25 P24 P31 to P24 0x00 P39 P38 P37 P36 P35 P34 P33 P32 P39 to P32 0x00 P47 P46 P45 P44 P43 P42 P41 P40 P47 to P40 0x00 P55 P54 P53 P52 P51 P50 P49 P48 P55 to P48 0x00 P63 P62 P61 P60 P59 P58 P57 P56 P63 to P56 0x00 P71 P70 P69 P68 P67 P66 P65 P64 P71 to P64 0x00 P79 P78 P77 P76 P75 P74 P73 P72 P79 to P72 0x00 P87 P86 P85 P84 P83 P82 P81 P80 P87 to P80 0x00 P95 P94 P93 P92 P91 P90 P89 P88 P95 to P88 0x00 P103 P102 P101 P100 P99 P98 P97 P96 P103 to P96 0x00 P111 P110 P109 P108 P107 P106 P105 P104 P111 to P104 0x00 P119 P118 P117 P116 P115 P114 P113 P112 P119 to P112 0x00 P127 P126 P125 P124 P123 P122 P121 P120 P127 to P120 0x00 Rev. J | Page 37 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 27. Register 0x80 to Register 0x83 SR7 to SR0 0x80 Register SD Mode Register 1 Bit Description SD standard 7 6 Bit Number 5 4 3 2 SD luma filter SD chroma filter 0x82 SD Mode Register 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 SD PrPb SSAF filter 0 1 0 1 Reserved SD pedestal 0 1 SD VCR FF/RW sync 0 1 SD pixel data valid SD Mode Register 3 0 1 0 1 SD pedestal YPrPb output 0 1 SD Output Levels Y 0 1 SD Output Levels PrPb 0 0 1 1 SD vertical blanking interval (VBI) open 0 1 0 1 0 1 SD closed captioning field control Reserved Register Setting NTSC PAL B, PAL D, PAL G, PAL H, PAL I PAL M PAL N LPF NTSC LPF PAL Notch NTSC Notch PAL Luma SSAF Luma CIF Luma QCIF Reserved 1.3 MHz 0.65 MHz 1.0 MHz 2.0 MHz Reserved Chroma CIF Chroma QCIF 3.0 MHz Disabled Enabled See Table 37 Reset Value 0x10 0x0B 0 0 1 SD square pixel mode SD active video edge control 0 0 1 0 1 0 1 0 1 0 1 0 1 SD DAC Output 1 0x83 1 0 0 1 1 0 0 1 1 0 1 0 1 0 Rev. J | Page 38 of 107 Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled No pedestal on YPrPb 7.5 IRE pedestal on YPrPb Y = 700 mV/300 mV Y = 714 mV/286 mV 700 mV p-p (PAL), 1000 mV p-p (NTSC) 700 mV p-p 1000 mV p-p 648 mV p-p Disabled Enabled Closed captioning disabled Closed captioning on odd field only Closed captioning on even field only Closed captioning on both fields Reserved 0x04 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 28. Register 0x84 to Register 0x87 SR7 to SR0 0x84 Register SD Mode Register 4 Bit Description Reserved SD SFL/SCR/TR mode select 7 6 Bit Number 5 4 3 2 1 0 1 0 1 SD active video length 0 1 SD chroma 0 1 SD burst 0 1 SD color bars 0 1 SD luma/chroma swap 0x86 SD Mode Register 5 0 1 NTSC color subcarrier adjust (delay from the falling edge of output HSYNC pulse to the start of color burst) Reserved SD EIA/CEA-861B synchronization compliance 0x87 SD Mode Register 6 0 0 1 0 1 0 1 1 0 1 Disabled. SFL mode enabled. 720 pixels. 710 (NTSC), 702 (PAL). Chroma enabled. Chroma disabled. Enabled. Disabled. Disabled. Enabled. DAC 2 = luma, DAC 3 = chroma. DAC 2 = chroma, DAC 3 = luma. 5.17 s. 5.31 s. 5.59 s (must be set for Macrovision compliance). Reserved. Reset Value 0x00 0x02 0 Disabled. Enabled. 0 0 1 0 1 SD luma and color scale control 0 1 SD luma scale saturation 0 1 SD hue adjust 0 1 SD brightness 0 1 SD luma SSAF gain 0 1 SD input standard autodetection Reserved SD RGB input enable2 Register Setting 0 Reserved SD horizontal/vertical counter mode 1 SD RGB color swap 2 0 0 0 1 0 0 1 Update field/line counter. Field/line counter free running. Normal. Color reversal enabled. Disabled. Enabled. Disabled. Enabled. Disabled. Enabled. Disabled. Enabled. Disabled. Enabled. Disabled. Enabled. 0 must be written to this bit. SD YCrCb input. SD RGB input. When set to 0, the horizontal/vertical counters automatically wrap around at the end of the line/field/frame of the selected standard. When set to 1, the horizontal/vertical counters are free running and wrap around when external sync signals indicate to do so. 2 Available on the ADV7392/ADV7393 (40-pin devices) only. 1 Rev. J | Page 39 of 107 0x00 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 29. Register 0x88 to Register 0x89 SR7 to SR0 0x88 Register SD Mode Register 7 Bit Description Reserved SD noninterlaced mode 7 6 Bit Number 5 4 3 2 0 1 SD input format SD digital noise reduction 0 1 0 1 1 0 1 SD gamma correction curve select 0 1 SD undershoot limiter 0 0 1 1 Reserved Reserved SD chroma delay 0 1 0 1 0 0 0 0 1 1 Reserved 1 0 0 1 0 1 SD gamma correction enable SD Mode Register 8 0 0 0 1 SD double buffering 0x89 1 0 0 1 0 1 0 Register Setting Disabled. Enabled. Disabled. Enabled. 8-bit YCbCr input. 16-bit YCbCr input. 1 10-bit YCbCr/16-bit SD RGB input.1 Reserved. Disabled. Enabled. Disabled. Enabled. Gamma Correction Curve A. Gamma Correction Curve B. Disabled. -11 IRE. -6 IRE. -1.5 IRE. 0 must be written to this bit. Reserved. Disabled. 4 clock cycles. 8 clock cycles. Reserved. 0 must be written to these bits. Reset Value 0x00 0x00 Available on the ADV7392/ADV7393 (40-pin devices) only. Table 30. Register 0x8A to Register 0x98 SR7 to SR0 0x8A Register SD Timing Register 0 Bit Description SD slave/master mode 7 6 Bit Number 1 5 4 3 2 1 0 0 1 1 0 1 0 1 SD timing mode Reserved SD luma delay Register Setting Slave mode. Master mode. Mode 0. Mode 1. Mode 2. Mode 3. 1 0 0 1 1 SD minimum luma value SD timing reset 0 0 1 0 1 x Rev. J | Page 40 of 107 0 1 0 1 No delay. Two clock cycles. Four clock cycles. Six clock cycles. -40 IRE. -7.5 IRE. A low-high-low transition resets the internal SD timing counters. Reset Value 0x08 Data Sheet SR7 to SR0 0x8B Register SD Timing Register 1 Note: Applicable in master modes only, that is, Subaddress 0x8A, Bit 0 = 1. ADV7390/ADV7391/ADV7392/ADV7393 Bit Description SD HSYNC width 7 Bit Number 1 5 4 3 2 6 SD HSYNC to VSYNC delay SD HSYNC to VSYNC rising edge delay (Mode 1 only) X2 X2 SD VSYNC width (Mode 2 only) 0 0 1 1 0 1 0 1 0 1 0 0 1 1 0 1 0 1 1 0 0 1 1 0 0 1 0 1 0x8C SD FSC Register 0 3 Subcarrier Frequency Bits[7:0] 0 0 1 1 x 0x8D SD FSC Register 13 Subcarrier Frequency Bits[15:8] x x x x x x x x 0x8E SD FSC Register 23 Subcarrier Frequency Bits[23:16] x x x x x x x x 0x8F SD FSC Register 33 Subcarrier Frequency Bits[31:24] x x x x x x x x 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 SD FSC Phase SD Closed Captioning SD Closed Captioning SD Closed Captioning SD Closed Captioning SD Pedestal Register 0 SD Pedestal Register 1 SD Pedestal Register 2 SD Pedestal Register 3 Subcarrier Phase Bits[9:2] Extended data on even fields Extended data on even fields Data on odd fields Data on odd fields Pedestal on odd fields Pedestal on odd fields Pedestal on even fields Pedestal on even fields x x x x x 17 25 17 25 x x x x x 16 24 16 24 x x x x x 15 23 15 23 x x x x x 14 22 14 22 x x x x x 13 21 13 21 x x x x x 12 20 12 20 x x x x x 11 19 11 19 x x x x x 10 18 10 18 SD HSYNC to pixel data adjust 0 1 0 1 x x x x x x x Register Setting ta = one clock cycle. ta = four clock cycles. ta = 16 clock cycles. ta = 128 clock cycles. tb = 0 clock cycles. tb = four clock cycles. tb = eight clock cycles. tb = 18 clock cycles. tc = tb. tc = tb + 32 s. One clock cycle. Four clock cycles. 16 clock cycles. 128 clock cycles. 0 clock cycles. One clock cycle. Two clock cycles. Three clock cycles. Subcarrier Frequency Bits[7:0]. Subcarrier Frequency Bits[15:8]. Subcarrier Frequency Bits[23:16]. Subcarrier Frequency Bits[31:24]. Subcarrier Phase Bits[9:2]. Extended Data Bits[7:0]. Extended Data Bits[15:8]. Data Bits[7:0]. Data Bits[15:8]. Setting any of these bits to 1 disables the pedestal on the line number indicated by the bit settings. Reset Value 0x00 0x1F 0x7C 0xF0 0x21 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 x = Logic 0 or Logic 1. X = don't care. 3 SD subcarrier frequency registers default to NTSC subcarrier frequency values. 1 2 Table 31. Register 0x99 to Register 0xA5 SR7 to SR0 0x99 Register SD CGMS/WSS 0 Bit Description SD CGMS data SD CGMS CRC 7 6 SD CGMS on odd fields SD CGMS on even fields SD WSS 0x9A SD CGMS/WSS 1 SD CGMS/WSS data Bit Number 1 5 4 3 2 x x 0 1 0 1 1 x 0 x x x 0 1 0 1 x x Rev. J | Page 41 of 107 x x Register Setting CGMS Data Bits[C19:C16] Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled CGMS Data Bits[C13:C8] or WSS Data Bits[W13:W8] Reset Value 0x00 0x00 ADV7390/ADV7391/ADV7392/ADV7393 SR7 to SR0 Register 0x9B SD CGMS/WSS 2 0x9C SD scale LSB 0x9D 0x9E 0x9F 0xA0 0xA1 SD Y scale SD Cb scale SD Cr scale SD hue adjust SD brightness/WSS 0xA2 SD luma SSAF 0xA3 SD DNR 0 Bit Description SD CGMS data SD CGMS/WSS data LSBs for SD Y scale value LSBs for SD Cb scale value LSBs for SD Cr scale value LSBs for SD FSC phase SD Y scale value SD Cb scale value SD Cr scale value SD hue adjust value SD brightness value SD blank WSS data Data Sheet 7 x x x x x x x 6 x x x x x x x x Bit Number 1 5 4 3 2 1 0 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 0 ... 0 ... 1 0 ... 1 ... 1 0 ... 1 ... 0 0 ... 0 ... 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 0 1 SD luma SSAF gain/attenuation (only applicable if Subaddress 0x87, Bit 4 = 1) Reserved Coring gain border (in DNR mode, the values in brackets apply) 0 Coring gain data (in DNR mode, the values in brackets apply) 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 Register Setting CGMS Data Bits[C15:C14] CGMS Data Bits[C7:C0] or WSS Data Bits[W7:W0] SD Y Scale Bits[1:0] SD Cb Scale Bits[1:0] SD Cr Scale Bits[1:0] Subcarrier Phase Bits[1:0] SD Y Scale Bits[9:2] SD Cb Scale Bits[9:2] SD Cr Scale Bits[9:2] SD Hue Adjust Bits[7:0] SD Brightness Bits[6:0] Disabled Enabled -4 dB ... 0 dB ... +4 dB Reset Value 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0 0 1 0 1 0 1 0 1 0 Rev. J | Page 42 of 107 No gain +1/16 [-1/8] +2/16 [-2/8] +3/16 [-3/8] +4/16 [-4/8] +5/16 [-5/8] +6/16 [-6/8] +7/16 [-7/8] +8/16 [-1] No gain +1/16 [-1/8] +2/16 [-2/8] +3/16 [-3/8] +4/16 [-4/8] +5/16 [-5/8] +6/16 [-6/8] +7/16 [-7/8] +8/16 [-1] 0x00 Data Sheet SR7 to SR0 0xA4 Register SD DNR 1 ADV7390/ADV7391/ADV7392/ADV7393 Bit Description DNR threshold 7 Border area Block size 0xA5 SD DNR 2 6 Bit Number 1 5 4 3 2 0 0 0 0 0 0 0 0 ... ... ... ... 1 1 1 1 1 1 1 1 0 1 1 0 1 0 1 0 0 1 0 0 0 1 DNR mode 1 0 0 1 ... 0 1 0 1 DNR input select DNR block offset 1 0 0 ... 1 1 0 1 0 0 ... 1 1 0 0 ... 1 1 0 0 ... 1 1 0 1 ... 0 1 Register Setting 0 1 ... 62 63 Two pixels Four pixels Eight pixels 16 pixels Filter A Filter B Filter C Filter D DNR mode DNR sharpness mode 0 pixel offset One pixel offset ... 14 pixel offset 15 pixel offset Reset Value 0x00 0x00 x = Logic 0 or Logic 1. Table 32. Register 0xA6 to Register 0xBB SR7 to SR0 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA Register SD Gamma A0 SD Gamma A1 SD Gamma A2 SD Gamma A3 SD Gamma A4 SD Gamma A5 SD Gamma A6 SD Gamma A7 SD Gamma A8 SD Gamma A9 SD Gamma B0 SD Gamma B1 SD Gamma B2 SD Gamma B3 SD Gamma B4 SD Gamma B5 SD Gamma B6 SD Gamma B7 SD Gamma B8 SD Gamma B9 SD brightness detect Bit Description SD Gamma Curve A (Point 24) SD Gamma Curve A (Point 32) SD Gamma Curve A (Point 48) SD Gamma Curve A (Point 64) SD Gamma Curve A (Point 80) SD Gamma Curve A (Point 96) SD Gamma Curve A (Point 128) SD Gamma Curve A (Point 160) SD Gamma Curve A (Point 192) SD Gamma Curve A (Point 224) SD Gamma Curve B (Point 24) SD Gamma Curve B (Point 32) SD Gamma Curve B (Point 48) SD Gamma Curve B (Point 64) SD Gamma Curve B (Point 80) SD Gamma Curve B (Point 96) SD Gamma Curve B (Point 128) SD Gamma Curve B (Point 160) SD Gamma Curve B (Point 192) SD Gamma Curve B (Point 224) SD brightness value 7 x x x x x x x x x x x x x x x x x x x x x 6 x x x x x x x x x x x x x x x x x x x x x Rev. J | Page 43 of 107 Bit Number 1 5 4 3 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 2 x x x x x x x x x x x x x x x x x x x x x 1 x x x x x x x x x x x x x x x x x x x x x 0 x x x x x x x x x x x x x x x x x x x x x Register Setting A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 Read only Reset Value 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xXX ADV7390/ADV7391/ADV7392/ADV7393 SR7 to SR0 0xBB 1 2 Register Field count Data Sheet Bit Description Field count Reserved Encoder version code 7 6 0 0 0 1 Bit Number 1 5 4 3 2 x 0 0 0 1 x 0 x Register Setting Read only Reserved Read only; first encoder version 2 Read only; second encoder version Reset Value 0x0X x = Logic 0 or Logic 1. See the HD Interlace External HSYNC and VSYNC Considerations section for information about the first encoder version. Table 33. Register 0xC9 to Register 0xCE SR7 to SR0 0xC9 Register Teletext control Bit Description Teletext enable 7 6 5 Bit Number 4 3 2 Teletext request mode 0xCB 0xCC 0xCD 0xCE 1 Teletext request control TTX Line Enable 0 TTX Line Enable 1 TTX Line Enable 2 TTX Line Enable 3 0 1 Reserved Teletext request falling edge position control 0 Teletext request rising edge position control 0 0 ... 1 1 22 14 22 14 Teletext on odd fields Teletext on odd fields Teletext on even fields Teletext on even fields 0 0 1 0 1 Teletext input pin select 1 0xCA 1 0 0 0 ... 1 1 21 13 21 13 0 0 0 ... 1 1 20 12 20 12 0 0 1 ... 0 1 19 11 19 11 0 0 0 ... 1 1 0 0 ... 1 1 0 0 ... 1 1 0 1 ... 0 1 18 10 18 10 17 9 17 9 16 8 16 8 15 7 15 7 The use of P0 as the teletext input pin is available on the ADV7392/ADV7393 (40-pin devices) only. Rev. J | Page 44 of 107 Register Setting Disabled. Enabled. Line request signal. Bit request signal. VSYNC. P0. Reserved. 0 clock cycles. One clock cycle. ... 14 clock cycles. 15 clock cycles. 0 clock cycles. One clock cycle. ... 14 clock cycles. 15 clock cycles. Setting any of these bits to 1 enables teletext on the line number indicated by the bit settings. Reset Value 0x00 0x00 0x00 0x00 0x00 0x00 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 34. Register 0xE0 to Register 0xF1 SR7 to SR0 0xE0 0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 0xE8 0xE9 0xEA 0xEB 0xEC 0xED 0xEE 0xEF 0xF0 0xF1 1 2 Register Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision Macrovision 2 Bit Description MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits MV control bits 7 x x x x x x x x x x x x x x x x x 0 6 x x x x x x x x x x x x x x x x x 0 5 x x x x x x x x x x x x x x x x x 0 Bit Number 1 4 3 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 0 0 x = Logic 0 or Logic 1. Macrovision registers are available on the ADV7390 and the ADV7392 only. Rev. J | Page 45 of 107 2 x x x x x x x x x x x x x x x x x 0 1 x x x x x x x x x x x x x x x x x 0 0 x x x x x x x x x x x x x x x x x x Register Setting Bits[7:1] must be 0. Reset Value 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet ADV7390/ADV7391 INPUT CONFIGURATION The ADV7390/ADV7391 support a number of different input modes. The desired input mode is selected using Subaddress 0x01, Bits[6:4]. The ADV7390/ADV7391 default to standard definition (SD) mode on power-up. Table 35 provides an overview of all possible input configurations. Each input mode is described in detail in this section. Note that the WLCSP option is only configured to support SD as shown in Figure 51. The CrCb pixel data is also input on Pin P7 to Pin P0 on the opposite edge of CLKIN. Pin P0 is the LSB. Whether the Y data is clocked in on the rising or falling edge of CLKIN is determined by Subaddress 0x01, Bits[2:1] (see Figure 52 and Figure 53). CLKIN Table 35. ADV7390/ADV7391 Input Configuration P7 P6 P5 P4 P3 YCrCb YCrCb YCrCb P2 P1 P0 P[7:0] 3FF 00 00 XY Cb0 Y0 Cr0 Y1 06234-050 Input Mode 000 SD 010 ED/HD-DDR 111 ED (at 54 MHz) NOTES 1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 00 IN THIS CASE. Figure 52. ED/HD-DDR Input Sequence (EAV/SAV)--Option A STANDARD DEFINITION CLKIN SD YCrCb data can be input in an interleaved 4:2:2 format over an 8-bit bus rate of 27 MHz. A 27 MHz clock signal must be provided on the CLKIN pin. If required, external synchronization signals can be provided on the HSYNC and VSYNC pins. P[7:0] 3FF Y0 MPEG2 DECODER Y1 Cr0 ADV7390/ ADV7391 CLKIN YCrCb VSYNC, HSYNC YCrCb 8 P[7:0] INTERLACED TO PROGRESSIVE CLKIN 8 P[7:0] 06234-049 2 YCrCb Cb0 VSYNC, HSYNC 06234-052 27MHz XY Figure 53. ED/HD-DDR Input Sequence (EAV/SAV)--Option B ADV7390/ ADV7391 2 00 NOTES 1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 11 IN THIS CASE. Embedded EAV/SAV timing codes are also supported. The ITU-R BT.601/656 input standard is supported. The interleaved pixel data is input on Pin P7 to Pin P0, with Pin P0 being the LSB. MPEG2 DECODER 00 06234-051 Subaddress 0x01, Bits[6:4] = 000 Figure 54. ED/HD-DDR Example Application Figure 51. SD Example Application ENHANCED DEFINITION (AT 54 MHz) ENHANCED DEFINITION/HIGH DEFINITION Subaddress 0x01, Bits[6:4] = 111 Subaddress 0x01, Bits[6:4] = 010 ED YCrCb data can be input in an interleaved 4:2:2 format over an 8-bit bus rate of 54 MHz. 8-Bit 4:2:2 ED/HD YCrCb Mode (DDR) In 8-bit DDR 4:2:2 YCrCb input mode, the Y pixel data is input on Pin P7 to Pin P0 on either the rising or falling edge of CLKIN. Pin P0 is the LSB. A 54 MHz clock signal must be provided on the CLKIN pin. Embedded EAV/SAV timing codes are supported. External synchronization signals are not supported in this mode. The interleaved pixel data is input on Pin P7 to Pin P0, with Pin P0 being the LSB. CLKIN P[7:0] 3FF 00 00 XY Cb0 Y0 Cr0 Figure 55. ED (at 54 MHz) Input Sequence (EAV/SAV) Rev. J | Page 46 of 107 Y1 06234-053 Enhanced definition (ED) or high definition (HD) YCrCb data can be input in an interleaved 4:2:2 format over an 8-bit DDR bus. The clock signal must be provided on the CLKIN pin. If required, external synchronization signals can be provided on the HSYNC and VSYNC pins. Embedded EAV/SAV timing codes are also supported. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 ADV7392/ADV7393 INPUT CONFIGURATION 16-Bit 4:2:2 YCrCb Mode Subaddress 0x87, Bit 7 = 0; Subaddress 0x88, Bits[4:3] = 01 The ADV7392/ADV7393 support a number of different input modes. The desired input mode is selected using Subaddress 0x01, Bits[6:4]. The ADV7392/ADV7393 default to standard definition (SD) mode on power-up. Table 36 provides an overview of all possible input configurations. Each input mode is described in detail in this section. In 16-bit 4:2:2 YCrCb input mode, the Y pixel data is input on Pin P15 to Pin P8, with Pin P8 being the LSB. The CrCb pixel data is input on Pin P7 to Pin P0, with Pin P0 being the LSB. STANDARD DEFINITION Subaddress 0x01, Bits[6:4] = 000 The pixel data is updated at half the rate of the clock, that is, at a rate of 13.5 MHz (see Figure 5). Standard definition YCrCb data can be input in 4:2:2 format over an 8-, 10-, or 16-bit bus. SD RGB data can be input in 4:4:4 format over a 16-bit bus. 16-Bit 4:4:4 RGB Mode A 27 MHz clock signal must be provided on the CLKIN pin. If required, external synchronization signals can be provided on the HSYNC and VSYNC pins. Embedded EAV/SAV timing codes are also supported in 8-bit and 10-bit modes. Embedded EAV/SAV timing codes are not supported with SD RGB mode. Also, master timing mode is not supported for SD RGB input mode, therefore, external synchronization must be used. 8-Bit 4:2:2 YCrCb Mode Subaddress 0x87, Bit 7 = 0; Subaddress 0x88, Bits[4:3] = 00 In 16-bit 4:4:4 RGB input mode, the red pixel data is input on Pin P4 to Pin P0, the green pixel data is input on Pin P10 to Pin P5, and the blue pixel data is input on Pin P15 to Pin P11. The P0, P5, and P11 pins are the respective bus LSBs. Subaddress 0x87, Bit 7 = 1 In 8-bit 4:2:2 YCrCb input mode, the interleaved pixel data is input on Pin P15 to Pin P8, with Pin P8 being the LSB. The ITU-R BT.601/656 input standard is supported. The pixel data is updated at half the rate of the clock, that is, at a rate of 13.5 MHz (see Figure 6). ADV7392/ ADV7393 2 MPEG2 DECODER 27MHz In 10-bit 4:2:2 YCrCb input mode, the interleaved pixel data is input on Pin P15 to Pin P6, with Pin P6 being the LSB. The ITUR BT.601/656 input standard is supported. YCrCb VSYNC, HSYNC CLKIN 8/10 P[15:8]/P[15:6] 06234-054 10-Bit 4:2:2 YCrCb Mode Subaddress 0x87, Bit 7 = 0; Subaddress 0x88, Bits[4:3] = 10 Figure 56. SD Example Application Table 36. ADV7392/ADV7393 Input Configuration Input Mode 1 000 SD 2 8-bit 10-bit 16-bit 3 001 010 111 16-bit3 ED/HD-SDR (16-bit) ED/HD-DDR 4 8-bit 10-bit ED (at 54 MHz) 8-bit 10-bit P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 SD RGB input enable (0x87[7]) = 0 P4 P3 P2 YCrCb YCrCb Y CrCb SD RGB input enable (0x87[7]) = 1 G B Y R CrCb ED/HD input format (0x33[2]) = 0 YCrCb ED/HD input format (0x33[2]) = 1 YCrCb ED/HD input format (0x33[2]) = 0 YCrCb ED/HD input format (0x33[2]) = 1 YCrCb The input mode is determined by Subaddress 0x01, Bits[6:4]. In SD mode, the width of the input data is determined by Subaddress 0x88, Bits[4:3]. 3 External synchronization signals must be used in this input mode. Embedded EAV/SAV timing codes are not supported. 4 ED = enhanced definition = 525p and 625p. 1 2 Rev. J | Page 47 of 107 P1 P0 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet MPEG2 DECODER Subaddress 0x01, Bits[6:4] = 001 or 010 ED or HD YCrCb data can be input in a 4:2:2 format over an 8-/10-bit DDR bus or a 16-bit SDR bus. ADV7392/ ADV7393 CLKIN YCrCb The clock signal must be provided on the CLKIN pin. If required, external synchronization signals can be provided on the HSYNC and VSYNC pins. Embedded EAV/SAV timing codes are also supported. INTERLACED TO PROGRESSIVE CrCb 8 Y 8 P[7:0] P[15:8] 2 16-Bit 4:2:2 YCrCb Mode (SDR) VSYNC HSYNC 06234-057 ENHANCED DEFINITION/HIGH DEFINITION Figure 59. ED/HD-SDR Example Application In 16-bit 4:2:2 YCrCb input mode, the Y pixel data is input on Pin P15 to Pin P8, with P8 being the LSB. The CrCb pixel data is input on Pin P7 to Pin P0, with Pin P0 being the LSB. MPEG2 DECODER 8-/10-Bit 4:2:2 YCrCb Mode (DDR) ADV7392/ ADV7393 CLKIN YCrCb In 8-/10-bit DDR 4:2:2 YCrCb input mode, the Y pixel data is input on Pin P15 to Pin P8/P6 on either the rising or falling edge of CLKIN. Pin P8/P6 is the LSB. YCrCb 8/10 2 The 10-bit mode is enabled using Subaddress 0x33, Bit 2. Whether the Y data is clocked in on the rising or falling edge of CLKIN is determined by Subaddress 0x01, Bits[2:1] (see Figure 57 and Figure 58). VSYNC HSYNC 06234-058 The CrCb pixel data is also input on Pin P15 to Pin P8/P6 on the opposite edge of CLKIN. P8/P6 is the LSB. Figure 60. ED/HD-DDR Example Application ENHANCED DEFINITION (AT 54 MHz) Subaddress 0x01, Bits[6:4] = 111 ED YCrCb data can be input in an interleaved 4:2:2 format on an 8-/10-bit bus at a rate of 54 MHz. CLKIN 3FF 00 00 XY Cb0 Y0 Cr0 A 54 MHz clock signal must be provided on the CLKIN pin. Embedded EAV/SAV timing codes are supported. External synchronization signals are not supported in this mode. Y1 06234-055 P[15:8]/ P]15:6] P[15:8]/P[15:6] INTERLACED TO PROGRESSIVE NOTES 1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 00 IN THIS CASE. 2. 10-BIT MODE IS ENABLED USING SUBADDRESS 0x33, BIT 2. Figure 57. ED/HD-DDR Input Sequence (EAV/SAV)--Option A The interleaved pixel data is input on Pin P15 to Pin P8/P6, with Pin P8/P6 being the LSB. The 10-bit mode is enabled using Subaddress 0x33, Bit 2. CLKIN CLKIN P[15:8]/P[15:6] 00 00 XY Y0 Cb0 Y1 3FF 00 00 XY Cb0 Y0 Cr0 Cr0 NOTES 1. SUBADDRESS 0x01 [2:1] SHOULD BE SET TO 11 IN THIS CASE. 2. 10-BIT MODE IS ENABLED USING SUBADDRESS 0x33, BIT 2. NOTES 1. 10-BIT MODE IS ENABLED USING SUBADDRESS 0x33, BIT 2. Figure 61. ED (at 54 MHz) Input Sequence (EAV/SAV) Figure 58. ED/HD-DDR Input Sequence (EAV/SAV)--Option B MPEG2 DECODER ADV7392/ ADV7393 YCrCb 8/10 INTERLACED TO PROGRESSIVE CLKIN P[15:8]/P[15:6] VSYNC, HSYNC Figure 62 ED (at 54 MHz) Example Application Rev. J | Page 48 of 107 06234-060 54MHz YCrCb Y1 06234-059 3FF 06234-056 P[15:8]/ P[15:P6] Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 OUTPUT CONFIGURATION The ADV7390/ADV7391/ADV7392/ADV7393 support a number of different output configurations. Table 37 to Table 39 list all possible output configurations. Table 37. SD Output Configurations RGB/YPrPb Output Select 1 (Subaddress 0x02, Bit 5) 0 1 1 1 1 SD DAC Output 1 (Subaddress 0x82, Bit 1) 0 0 1 1 SD Luma/Chroma Swap (Subaddress 0x84, Bit 7) 0 0 0 1 DAC 1 G Y CVBS CVBS DAC 2 B Pb Luma Chroma DAC 3 R Pr Chroma Luma ED/HD Color DAC Swap (Subaddress 0x35, Bit 3) 0 1 0 1 DAC 1 G G Y Y DAC 2 B R Pb Pr DAC 3 R B Pr Pb ED/HD Color DAC Swap (Subaddress 0x35, Bit 3) 0 1 0 1 DAC 1 G G Y Y DAC 2 B R Pb Pr DAC 3 R B Pr Pb If SD RGB output is selected, a color reversal is possible using Subaddress 0x86, Bit 7. Table 38. ED/HD Output Configurations RGB/YPrPb Output Select (Subaddress 0x02, Bit 5) 0 0 1 1 Table 39. ED (at 54 MHz) Output Configurations RGB/YPrPb Output Select (Subaddress 0x02, Bit 5) 0 0 1 1 Rev. J | Page 49 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet DESIGN FEATURES OUTPUT OVERSAMPLING The ADV7390/ADV7391/ADV7392/ADV7393 include an onchip phase-locked loop (PLL) that allows for oversampling of SD, ED, and HD video data. By default, the PLL is disabled. The PLL can be enabled using Subaddress 0x00, Bit 1 = 0. Table 40 shows the various oversampling rates supported in the ADV7390/ADV7391/ADV7392/ADV7393. External Sync Polarity For SD and ED/HD modes, the ADV7390/ADV7391/ADV7392/ ADV7393 parts typically expect HS and VS to be low during their respective blanking periods. However, when the CEA861 compliance bit is enabled (0x39, Bit 5 for ED/HD modes and 0x86, Bit 3 for SD modes), the part expects the HS or VS to be active low or high depending on the input format selected (0x30, Bits[7:3]). If a different polarity other than the default is required for ED/HD modes, 0x3A, Bits[2:0] can be used to invert PHSYNCB, PVSYNCB or PBLANKB individually regardless of whether CEA-861-B mode is enabled. It is not possible to invert S_HSYNC or S_VSYNC. Table 40. Output Oversampling Modes and Rates Input Mode (0x01, Bits[6:4]) 000 SD 000 SD 000 SD 001/010 ED 001/010 ED 001/010 ED 001/010 HD 001/010 HD 001/010 HD 111 ED (at 54 MHz) 111 ED (at 54 MHz) 111 ED (at 54 MHz) 1 PLL and Oversampling Control (0x00, Bit 1) 1 0 0 1 0 0 1 0 0 1 0 0 SD/ED Oversample Rate Select (0x0D, Bit 3)1 X 1 0 X 1 0 X X X X 1 0 X = don't care Rev. J | Page 50 of 107 HD Oversample Rate Select (0x31, Bit 1)1 X X X X X X X 1 0 X X X Oversampling Mode and Rate SD (2x) SD (8x) SD (16x) ED (1x) ED (4x) ED (8x) HD (1x) HD (2x) HD (4x) ED (at 54 MHz) (1x) ED (at 54 MHz) (4x) ED (at 54 MHz) (8x) Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 HD INTERLACE EXTERNAL HSYNC AND VSYNC CONSIDERATIONS ED/HD TIMING RESET If the encoder revision code (Subaddress 0xBB, Bits[7:6]) = 01 or higher, the user should set Subaddress 0x02, Bit 1 to high. To ensure correct timing in HD interlace modes when using HSYNC and VSYNC synchronization signals. If this bit is set to low, the first active pixel on each line is masked in HD interlace modes and the Pr and Pb outputs are swapped when using the YCrCb 4:2:2 input format. Setting Subaddress 0x02, Bit 1 to low causes the encoder to behave in the same way as the first version of silicon (that is, this setting is backward compatible). An ED/HD timing reset is achieved by setting the ED/HD timing reset control bit (Subaddress 0x34, Bit 0) to 1. In this state, the horizontal and vertical counters remain reset. When this bit is set back to 0, the internal counters resume counting. This timing reset applies to the ED/HD timing counters only. Subaddress 0x34, Bit 0 SD SUBCARRIER FREQUENCY LOCK Subcarrier Frequency Lock (SFL) Mode In subcarrier frequency lock (SFL) mode (Subaddress 0x84, Bits[2:1] = 11), the ADV7390/ADV7391/ADV7392/ADV7393 can be used to lock to an external video source. The SFL mode allows the ADV7390/ADV7391/ADV7392/ADV7393 to automatically alter the subcarrier frequency to compensate for line length variations. When the part is connected to a device such as an ADV7403 video decoder that outputs a digital data stream in the SFL format, the part automatically changes to the compensated subcarrier frequency on a line-by-line basis (see Figure 63). This digital data stream is 67 bits wide, and the subcarrier is contained in Bit 0 to Bit 21. Each bit is two clock cycles long. If the encoder revision code (Subaddress 0xBB, Bits[7:6]) = 00, the setting of Subaddress 0x02, Bit 1 has no effect. In this version of the encoder, the first active pixel is masked and the Pr and Pb outputs are swapped when using YCrCb 4:2:2 input format. To avoid these limitations, use the newer revision of silicon or use a different type of synchronization. These considerations apply only to the HD interlace modes with external HSYNC and VSYNC synchronization (EAV/SAV mode is not affected and always has correct timing). There is no negative effect in setting Subaddress 0x02, Bit 0 to high, and this bit can remain high for all the other video standards. ADV7390/ADV7391/ ADV7392/ADV7393 CLKIN DAC 1 LLC1 COMPOSITE VIDEO1 H/L TRANSITION COUNT START SFL SFL DAC 2 DAC 3 ADV7403 P19 TO VIDEO DECODER P10 14 BITS SUBCARRIER LOW PHASE 128 13 PIXEL PORT5 4 BITS RESERVED 0 21 14 19 SEQUENCE BIT3 FSC PLL INCREMENT 2 0 RESET BIT4 RESERVED RTC 6768 VALID SAMPLE INVALID SAMPLE 8/LINE LOCKED CLOCK 1FOR EXAMPLE, VCR OR CABLE. 2F SC PLL INCREMENT IS 22 BITS LONG. VALUE LOADED INTO ADV7390/ADV7391/ADV7392/ADV7393 FSC PLL INCREMENTS BITS[21:0] PLUS BITS[0:9] OF SUBCARRIER FREQUENCY REGISTERS. 3SEQUENCE BIT 5 BITS RESERVED F SC DDS REGISTER IS PAL: 0 = LINE NORMAL, 1 = LINE INVERTED NTSC: 0 = NO CHANGE 4RESET ADV7390/ADV7391/ADV7392/ADV7393 DDS. 5REFER TO THE ADV7390/ADV7391 AND ADV7392/ADV7393 INPUT CONFIGUR ATION TABLES FOR PIXEL DATA PIN ASSIGNMENTS. Figure 63. SD Subcarrier Frequency Lock Timing and Connections Diagram (Subaddress 0x84, Bits [2:1] = 11) Rev. J | Page 51 of 107 06234-064 TIME SLOT 01 ADV7390/ADV7391/ADV7392/ADV7393 SD VCR FF/RW SYNC Data Sheet For example, in NTSC mode: Subaddress 0x82, Bit 5 In DVD record applications where the encoder is used with a decoder, the VCR FF/RW sync control bit can be used for nonstandard input video, that is, in fast forward or rewind modes. In fast forward mode, the sync information at the start of a new field in the incoming video usually occurs before the correct number of lines/fields is reached. In rewind mode, this sync signal usually occurs after the total number of lines/fields is reached. Conventionally, this means that the output video has corrupted field signals because one signal is generated by the incoming video and another is generated when the internal line/field counters reach the end of a field. 227.5 32 Subcarrier Register Value = x 2 = 569408543 1716 where: Subcarrier Register Value = 569408543d = 0x21F07C1F SD FSC Register 0: 0x1F SD FSC Register 1: 0x7C SD FSC Register 2: 0xF0 SD FSC Register 3: 0x21 Programming the FSC When the VCR FF/RW sync control is enabled (Subaddress 0x82, Bit 5), the line/field counters are updated according to the incoming VSYNC signal and when the analog output matches the incoming VSYNC signal. This control is available in all slave-timing modes except Slave Mode 0. The subcarrier frequency register value is divided into four FSC registers as shown in the previous example. The four subcarrier frequency registers must be updated sequentially, starting with Subcarrier Frequency Register 0 and ending with Subcarrier Frequency Register 3. The subcarrier frequency updates only after the last subcarrier frequency register byte is received by the ADV7390/ADV7391/ADV7392/ADV7393. The SD input standard autodetection feature must be disabled. VERTICAL BLANKING INTERVAL Typical FSC Values Subaddress 0x31, Bit 4; Subaddress 0x83, Bit 4 Table 41 outlines the values that should be written to the subcarrier frequency registers for NTSC and PAL B/D/G/H/I. The ADV7390/ADV7391/ADV7392/ADV7393 are able to accept input data that contains vertical blanking interval (VBI) data (such as CGMS, WSS, VITS) in SD, ED, and HD modes. Table 41. Typical FSC Values If VBI is disabled (Subaddress 0x31, Bit 4 for ED/HD; Subaddress 0x83, Bit 4 for SD), VBI data is not present at the output and the entire VBI is blanked. These control bits are valid in all master and slave timing modes. Subaddress 0x8C 0x8D 0x8E 0x8F For the SMPTE 293M (525p) standard, VBI data can be inserted on Line 13 to Line 42 of each frame or on Line 6 to Line 43 for the ITU-R BT.1358 (625p) standard. VBI data can be present on Line 10 to Line 20 for NTSC and on Line 7 to Line 22 for PAL. SD NONINTERLACED MODE In SD Timing Mode 0 (slave option), if VBI is enabled, the blanking bit in the EAV/SAV code is overwritten. It is possible to use VBI in this timing mode as well. If CGMS is enabled and VBI is disabled, the CGMS data is, nevertheless, available at the output. SD SUBCARRIER FREQUENCY CONTROL Subaddress 0x8C to Subaddress 0x8F The ADV7390/ADV7391/ADV7392/ADV7393 are able to generate the color subcarrier used in CVBS and S-Video (Y-C) outputs from the input pixel clock. Four 8-bit registers are used to set up the subcarrier frequency. The value of these registers is calculated using the following equation: Subcarrier Frequency Register = Number of subcarrier periods in one video line Number of 27 MHz clock cycles in one video line where the sum is rounded to the nearest integer. x 2 32 Description FSC0 FSC1 FSC2 FSC3 NTSC 0x1F 0x7C 0xF0 0x21 PAL B/D/G/H/I 0xCB 0x8A 0x09 0x2A Subaddress 0x88, Bit 1 The ADV7390/ADV7391/ADV7392/ADV7393 support an SD noninterlaced mode. Using this mode, progressive inputs at twice the frame rate of NTSC and PAL (240p/59.94 Hz and 288p/50 Hz, respectively) can be input into the ADV7390/ ADV7391/ADV7392/ADV7393. The SD noninterlaced mode can be enabled using Subaddress 0x88, Bit 1. A 27 MHz clock signal must be provided on the CLKIN pin. Embedded EAV/SAV timing codes or external horizontal and vertical synchronization signals provided on the HSYNC and VSYNC pins can be used to synchronize the input pixel data. All input configurations, output configurations, and features available in NTSC and PAL modes are available in SD noninterlaced mode. For 240p/59.94 Hz input, the ADV7390/ADV7391/ ADV7392/ADV7393 should be configured for NTSC operation and Subaddress 0x88, Bit 1 should be set to 1. For 288p/50 Hz input, the ADV7390/ADV7391/ADV7392/ ADV7393 should be configured for PAL operation and Subaddress 0x88, Bit 1 should be set to 1. Rev. J | Page 52 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 SD SQUARE PIXEL MODE Subaddress 0x82, Bit 4 The ADV7390/ADV7391/ADV7392/ADV7393 support an SD square pixel mode (Subaddress 0x82, Bit 4). For NTSC operation, an input clock of 24.5454 MHz is required. The active resolution is 640 x 480. For PAL operation, an input clock of 29.5 MHz is required. The active resolution is 768 x 576. For CVBS and S-Video (Y-C) outputs, the SD subcarrier frequency registers must be updated to reflect the input clock frequency used in SD square pixel mode. The SD input standard autodetection feature must be disabled in SD square pixel mode. In square pixel mode, the timing diagrams shown in Figure 64 and Figure 65 apply. ANALOG VIDEO EAV CODE NTSC/PAL M SYSTEM (525 LINES/60Hz) PAL SYSTEM (625 LINES/50Hz) 4 CLOCK SAV CODE 0 F F A A A 0 F F B B B C C 8 1 8 1 F 0 0 X C Y C Y C Y r Y b b r 0 0 0 0 F 0 0 Y b ANCILLARY DATA (HANC) 4 CLOCK 272 CLOCK 1280 CLOCK 4 CLOCK 4 CLOCK 344 CLOCK 1536 CLOCK 06234-065 INPUT PIXELS F 0 0 X 8 1 8 1 C Y Y F 0 0 Y 0 0 0 0 r START OF ACTIVE VIDEO LINE END OF ACTIVE VIDEO LINE Figure 64. Square Pixel Mode EAV/SAV Embedded Timing HSYNC FIELD Cb Y Cr Y PAL = 308 CLOCK CYCLES NTSC = 236 CLOCK CYCLES Figure 65. Square Pixel Mode Active Pixel Timing Rev. J | Page 53 of 107 06234-066 PIXEL DATA ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet FILTERS EXTENDED (SSAF) PrPb FILTER MODE 0 Table 42 shows an overview of the programmable filters available on the ADV7390/ADV7391/ADV7392/ADV7393. -10 Table 42. Selectable Filters Subaddress 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x80 0x82 0x33 0x33 GAIN (dB) -20 -30 -40 -50 -60 0 1 2 3 4 FREQUENCY (MHz) 5 6 06234-067 Filter SD Luma LPF NTSC SD Luma LPF PAL SD Luma Notch NTSC SD Luma Notch PAL SD Luma SSAF SD Luma CIF SD Luma QCIF SD Chroma 0.65 MHz SD Chroma 1.0 MHz SD Chroma 1.3 MHz SD Chroma 2.0 MHz SD Chroma 3.0 MHz SD Chroma CIF SD Chroma QCIF SD PrPb SSAF ED/HD Sinc Compensation Filter ED/HD Chroma SSAF Figure 66. PrPb SSAF Filter If this filter is disabled, one of the chroma filters shown in Table 43 can be selected and used for the CVBS or luma/ chroma signal. Table 43. Internal Filter Specifications SD Internal Filter Response Subaddress 0x80, Bits[7:2]; Subaddress 0x82, Bit 0 The Y filter supports several different frequency responses, including two low-pass responses, two notch responses, an extended (SSAF) response with or without gain boost attenuation, a CIF response, and a QCIF response. The PrPb filter supports several different frequency responses, including six low-pass responses, a CIF response, and a QCIF response, as shown in Figure 38 and Figure 39. If SD Luma SSAF gain is enabled (Subaddress 0x87, Bit 4), there are 13 response options in the range -4 dB to +4 dB. The desired response can be programmed using Subaddress 0xA2. Variation in frequency responses is shown in Figure 35 to Figure 37. In addition to the chroma filters listed in Table 42, the ADV7390/ ADV7391/ADV7392/ADV7393 contain an SSAF filter that is specifically designed for the color difference component outputs, Pr and Pb. This filter has a cutoff frequency of ~2.7 MHz and a gain of -40 dB at 3.8 MHz (see Figure 66). This filter can be controlled with Bit 0 of Sub-address 0x82, Bit 0. Filter Luma LPF NTSC Luma LPF PAL Luma Notch NTSC Luma Notch PAL Luma SSAF Luma CIF Luma QCIF Chroma 0.65 MHz Chroma 1.0 MHz Chroma 1.3 MHz Chroma 2.0 MHz Chroma 3.0 MHz Chroma CIF Chroma QCIF Pass-Band Ripple (dB)1 0.16 0.1 0.09 0.1 0.04 0.127 Monotonic Monotonic Monotonic 0.09 0.048 Monotonic Monotonic Monotonic 3 dB Bandwidth (MHz)2 4.24 4.81 2.3/4.9/6.6 3.1/5.6/6.4 6.45 3.02 1.5 0.65 1 1.395 2.2 3.2 0.65 0.5 Pass-band ripple is the maximum fluctuation from the 0 dB response in the pass band, measured in decibels. The pass band is defined to have 0 Hz to fc (Hz) frequency limits for a low-pass filter and 0 Hz to f1 (Hz) and f2 (Hz) to infinity for a notch filter, where fc, f1, and f2 are the -3 dB points. 2 3 dB bandwidth refers to the -3 dB cutoff frequency. 1 Rev. J | Page 54 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 ED/HD Sinc Compensation Filter Response Subaddress 0x33, Bit 3 The ADV7390/ADV7391/ADV7392/ADV7393 include a filter designed to counter the effect of sinc roll-off in DAC 1, DAC 2, and DAC 3 while operating in ED/HD mode. This filter is enabled by default. It can be disabled using Subaddress 0x33, Bit 3. The benefit of the filter is illustrated in Figure 67 and Figure 68. 0.5 0.4 0.3 GAIN (dB) 0.2 0.1 0 Table 44. Sample Color Values for EIA770.2/EIA770.3 ED/HD Output Standard Selection Sample Color White Black Red Green Blue Yellow Cyan Magenta Y Value 235 (0xEB) 16 (0x10) 81 (0x51) 145 (0x91) 41 (0x29) 210 (0xD2) 170 (0xAA) 106 (0x6A) Cr Value 128 (0x80) 128 (0x80) 240 (0xF0) 34 (0x22) 110 (0x6E) 146 (0x92) 16 (0x10) 222 (0xDE) Cb Value 128 (0x80) 128 (0x80) 90 (0x5A) 54 (0x36) 240 (0xF0) 16 (0x10) 166 (0xA6) 202 (0xCA) -0.1 -0.2 COLOR SPACE CONVERSION MATRIX -0.3 Subaddress 0x03 to Subaddress 0x09 -0.5 0 5 10 15 20 FREQUENCY (MHz) 25 30 06234-068 -0.4 Figure 67. ED/HD Sinc Compensation Filter Enabled 0.5 0.4 The internal color space conversion (CSC) matrix automatically performs all color space conversions based on the input mode programmed in the mode select register (Subaddress 0x01, Bits[6:4]). Table 45 and Table 46 show the options available in this matrix. An SD color space conversion from RGB-in to YPrPb-out is possible on the ADV7392/ADV7393. An ED/HD color space conversion from RGB-in to YPrPb-out is not possible. 0.3 0.2 GAIN (dB) Table 44 shows sample color values that can be programmed into the color registers when the output standard selection is set to EIA770.2/EIA770.3 (Subaddress 0x30, Bits[1:0] = 00). 0.1 Table 45. SD Color Space Conversion Options 0 -0.1 -0.2 -0.3 -0.5 0 5 10 15 20 FREQUENCY (MHz) 25 30 06234-069 -0.4 Figure 68. ED/HD Sinc Compensation Filter Disabled Input YCrCb YCrCb RGB2 RGB2 1 2 ED/HD TEST PATTERN COLOR CONTROLS Output1 YPrPb RGB YPrPb RGB YPrPb/RGB Out (Subaddress 0x02, Bit 5) 1 0 1 0 RGB In/YCrCb In (Subaddress 0x87, Bit 7) 0 0 1 1 CVBS/Y-C outputs are available for all CSC combinations. Available on the ADV7392/ADV7393 (40-pin devices) only. Table 46. ED/HD Color Space Conversion Options Subaddress 0x36 to Subaddress 0x38 Three 8-bit registers at Subaddress 0x36 to Subaddress 0x38 are used to program the output color of the internal ED/HD test pattern generator (Subaddress 0x31, Bit 2 = 1), whether it be the lines of the crosshatch pattern or the uniform field test pattern. They are not functional as color controls for external pixel data input. The values for the luma (Y) and color difference (Cr and Cb) signals used to obtain white, black, and saturated primary and complementary colors conform to the ITU-R BT.601-4 standard. Input YCrCb YCrCb Output YPrPb RGB YPrPb/RGB Out (Subaddress 0x02, Bit 5) 1 0 SD Manual CSC Matrix Adjust Feature The SD manual CSC matrix adjust feature (available for the ADV7392 and ADV7393 only) provides custom coefficient manipulation for RGB to YPbPr conversion (for YPbPr to RGB conversion, this matrix adjustment is not available). Normally, there is no need to modify the SD matrix coefficients because the CSC matrix automatically performs the color space conversion based on the output color space selected (see Table 46). Note that Bit 7 in subaddress 0x87 must be set to enable RGB input and, therefore, use the CSC manual adjustment. Rev. J | Page 55 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Y = (a1 x R) + (a2 x G) + (a3 x B) + a4 On power-up, the CSC matrix is programmed with the default values shown in Table 48. Pr = (b1 x R) + (b2 x G) + (b3 x B) + b4 Table 48. ED/HD Manual CSC Matrix Default Values Pb = (c1 x R) + (c2 x G) + (c3 x B) + c4 Subaddress 0x03 0x04 0x05 0x06 0x07 0x08 0x09 The SD CSC matrix scalar uses the following equations: The coefficients and their default values are located in the registers shown in Table 47. Table 47. SD Manual CSC Matrix Default Values Coefficient a1 a2 a3 a4 b1 b2 b3 b4 c1 c2 c3 c4 Subaddress 0xBD 0xBE 0xBF 0xC0 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 Default 0x42 0x81 0x19 0x10 0x70 0x5E 0x12 0x80 0x26 0x4A 0x70 0x80 Default 0x03 0xF0 0x4E 0x0E 0x24 0x92 0x7C When the ED/HD manual CSC matrix adjust feature is enabled, the default coefficient values in Subaddress 0x03 to Subaddress 0x09 are correct for the HD color space only. The color components are converted according to the following 1080i and 720p standards (SMPTE 274M, SMPTE 296M): R = Y + 1.575Pr G = Y - 0.468Pr - 0.187Pb B = Y + 1.855Pb ED/HD Manual CSC Matrix Adjust Feature The ED/HD manual CSC matrix adjust feature provides custom coefficient manipulation for color space conversions and is used in ED and HD modes only. The ED/HD manual CSC matrix adjust feature can be enabled using Subaddress 0x02, Bit 3. Normally, there is no need to enable this feature because the CSC matrix automatically performs the color space conversion based on the input mode chosen (ED or HD) and the output color space selected (see Table 46). For this reason, the ED/HD manual CSC matrix adjust feature is disabled by default. If RGB output is selected, the ED/HD CSC matrix scalar uses the following equations: The conversion coefficients should be multiplied by 315 before being written to the ED/HD CSC matrix registers. This is reflected in the default values for GY = 0x13B, GU = 0x03B, GV = 0x093, BU = 0x248, and RV = 0x1F0. If the ED/HD manual CSC matrix adjust feature is enabled and another input standard (such as ED) is used, the scale values for GY, GU, GV, BU, and RV must be adjusted according to this input standard color space. The user should consider that the color component conversion may use different scale values. For example, SMPTE 293M uses the following conversion: R = Y + 1.402Pr G = Y - 0.714Pr - 0.344Pb R = GY x Y + RV x Pr B = Y + 1.773Pb G = GY x Y - (GU x Pb) - (GV x Pr) Note that subtractions are implemented in the hardware. The programmable CSC matrix is used for external ED/HD pixel data and is not functional when internal test patterns are enabled. If YPrPb output is selected, the following equations are used: Programming the CSC Matrix B = GY x Y + BU x Pb Y = GY x Y If custom manipulation of the ED/HD CSC matrix coefficients is required for a YCrCb-to-RGB color space conversion, use the following procedure: Pr = RV x Pr Pb = BU x Pb where: GY = Subaddress 0x05, Bits[7:0] and Subaddress 0x03, Bits[1:0]. GU = Subaddress 0x06, Bits[7:0] and Subaddress 0x04, Bits[7:6]. GV = Subaddress 0x07, Bits[7:0] and Subaddress 0x04, Bits[5:4]. BU = Subaddress 0x08, Bits[7:0] and Subaddress 0x04, Bits[3:2]. RV = Subaddress 0x09, Bits[7:0] and Subaddress 0x04, Bits[1:0]. 1. 2. 3. 4. Enable the ED/HD manual CSC matrix adjust feature (Subaddress 0x02, Bit 3). Set the output to RGB (Subaddress 0x02, Bit 5). Disable sync on PrPb (Subaddress 0x35, Bit 2). Enable sync on RGB (optional) (Subaddress 0x02, Bit 4). The GY value controls the green signal output level, the BU value controls the blue signal output level, and the RV value controls the red signal output level. Rev. J | Page 56 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 For example, to adjust the hue by +4, write 0x97 to the hue adjust control register. SD LUMA AND COLOR SCALE CONTROL Subaddress 0x9C to Subaddress 0x9F When enabled, the SD luma and color scale control feature can be used to scale the SD Y, Cb, and Cr output levels. This feature can be enabled using Subaddress 0x87, Bit 0. This feature affects all SD output signals, that is, CVBS, Y-C, YPrPb, and RGB. When enabled, three 10-bit registers (SD Y scale, SD Cb scale, and SD Cr scale) control the scaling of the SD Y, Cb, and Cr output levels. The SD Y scale register contains the scaling factor used to scale the Y level from 0.0 to 1.5 times its initial level. The SD Cb scale and SD Cr scale registers contain the scaling factors to scale the Cb and Cr levels from 0.0 to 2.0 times their initial levels, respectively. The values to be written to these 10-bit registers are calculated using the following equation: Y, Cb, or Cr Scale Value = Scale Factor x 512 For example, if Scale Factor = 1.3 Y, Cb, or Cr Scale Value = 1.3 x 512 = 665.6 Y, Cb, or Cr Scale Value = 666 (rounded to the nearest integer) Y, Cb, or Cr Scale Value = 1010011010b 4 128 151d 0x97 0.17578125 where the sum is rounded to the nearest integer. To adjust the hue by -4, write 0x69 to the hue adjust control register. 4 128 105d 0x69 0.17578125 where the sum is rounded to the nearest integer. SD BRIGHTNESS DETECT Subaddress 0xBA The ADV7390/ADV7391/ADV7392/ADV7393 allow monitoring of the brightness level of the incoming video data. This feature is used to monitor the average brightness of the incoming Y signal on a field-by-field basis. The information is read from the I2C and, based on this information, the color saturation, contrast, and brightness controls can be adjusted (for example, to compensate for very dark pictures). The luma data is monitored in the active video area only. The average brightness I2C register is updated on the falling edge of every VSYNC signal. The SD brightness detect register (Subaddress 0xBA) is a read-only register. It is recommended that the SD luma scale saturation feature (Subaddress 0x87, Bit 1) be enabled when scaling the Y output level to avoid excessive Y output levels. SD HUE ADJUST CONTROL Subaddress 0xA0 When enabled, the SD hue adjust control register (Subaddress 0xA0) is used to adjust the hue on the SD composite and chroma outputs. This feature can be enabled using Subaddress 0x87, Bit 2. Subaddress 0xA0 contains the bits required to vary the hue of the video data, that is, the variance in phase of the subcarrier during active video with respect to the phase of the subcarrier during the color burst. The ADV7390/ADV7391/ADV7392/ ADV7393 provide a range of 22.5 in increments of 0.17578125. For normal operation (zero adjustment), this register is set to 0x80. Value 0xFF and Value 0x00 represent the upper and lower limits, respectively, of the attainable adjustment in NTSC mode. Value 0xFF and Value 0x01 represent the upper and lower limits, respectively, of the attainable adjustment in PAL mode. The hue adjust value is calculated using the following equation: SD BRIGHTNESS CONTROL Subaddress 0xA1, Bits[6:0] When this feature is enabled, the SD brightness/WSS control register (Subaddress 0xA1) is used to control brightness by adding a programmable setup level onto the scaled Y data. This feature can be enabled using Subaddress 0x87, Bit 3. For NTSC with pedestal, the setup can vary from 0 IRE to 22.5 IRE. For NTSC without pedestal (see Figure 69) and for PAL, the setup can vary from -7.5 IRE to +15 IRE. NTSC WITHOUT PEDESTAL +7.5 IRE 100 IRE 0 IRE -7.5 IRE NO SETUP VALUE ADDED POSITIVE SETUP VALUE ADDED NEGATIVE SETUP VALUE ADDED 06234-070 Subaddress 0x9C, SD scale LSB = 0x2A Subaddress 0x9D, SD Y scale register = 0xA6 Subaddress 0x9E, SD Cb scale register = 0xA6 Subaddress 0x9F, SD Cr scale register = 0xA6 Figure 69. Examples of Brightness Control Values The SD brightness control register is an 8-bit register. The seven LSBs of this 8-bit register are used to control the brightness level, which can be a positive or negative value. For example, to add a +20 IRE brightness level to an NTSC signal with pedestal, write 0x28 to Subaddress 0xA1. 0 x (SD Brightness Value) = Hue Adjust () = 0.17578125 (HCRd - 128) 0 x (IRE Value x 2.015631) = Where HCRd = the hue adjust control register (decimal). 0 x (20 x 2.015631) = 0 x (40.31262) 0x28 Rev. J | Page 57 of 107 ADV7390/ADV7391/ADV7392/ADV7393 To add a -7 IRE brightness level to a PAL signal, write 0x72 to Subaddress 0xA1. 0 x (SD Brightness Value) = PROGRAMMABLE DAC GAIN CONTROL Subaddress 0x0B 0 x (IRE Value x 2.075631) = It is possible to adjust the DAC output signal gain up or down from its absolute level. This is illustrated in Figure 70. 0 x (7 x 2.015631) = 0x(14.109417) 0001110b DAC 1 to DAC 3 are controlled by Register 0x0B. 0001110b into twos complement = 1110010b = 0x72 In Case A of Figure 70, the video output signal is gained. The absolute level of the sync tip and the blanking level increase with respect to the reference video output signal. The overall gain of the signal is increased from the reference signal. Table 49. Sample Brightness Control Values1 Setup Level (NTSC) with Pedestal 22.5 IRE 15 IRE 7.5 IRE 0 IRE 1 Data Sheet Setup Level (NTSC) Without Pedestal 15 IRE 7.5 IRE 0 IRE -7.5 IRE Setup Level (PAL) 15 IRE 7.5 IRE 0 IRE -7.5 IRE Brightness Control Value 0x1E 0x0F 0x00 0x71 Values in the range of 0x3F to 0x44 may result in an invalid output signal. SD INPUT STANDARD AUTODETECTION In Case B of Figure 70, the video output signal is reduced. The absolute level of the sync tip and the blanking level decrease with respect to the reference video output signal. The overall gain of the signal is reduced from the reference signal. CASE A GAIN PROGRAMMED IN DAC OUTPUT LEVEL REGISTERS, SUBADDRESS 0x0B 700mV Subaddress 0x87, Bit 5 The ADV7390/ADV7391/ADV7392/ADV7393 include an SD input standard autodetect feature that can be enabled by setting Subaddress 0x87, Bits[5:1]. When enabled, the ADV7390/ADV7391/ADV7392/ADV7393 can automatically identify an NTSC or a PAL B/D/G/H/I input stream. The ADV7390/ADV7391/ADV7392/ADV7393 automatically update the subcarrier frequency registers with the appropriate value for the identified standard. The ADV7390/ ADV7391/ADV7392/ADV7393 are also configured to correctly encode the identified standard. The SD standard bits (Subaddress 0x80, Bits[1:0]) and the subcarrier frequency registers are not updated to reflect the identified standard. All registers retain their default or userdefined values. DOUBLE BUFFERING 300mV CASE B NEGATIVE GAIN PROGRAMMED IN DAC OUTPUT LEVEL REGISTERS, SUBADDRESS 0x0B 700mV 300mV Double-buffered registers are updated once per field. Double buffering improves overall performance because modifications to register settings are not be made during active video but take effect prior to the start of the active video on the next field. Using Subaddress 0x33, Bit 7, double buffering can be activated on the following ED/HD registers: the ED/HD Gamma A and Gamma B curves and ED/HD CGMS registers. 06234-071 Subaddress 0x33, Bit 7 for ED/HD; Subaddress 0x88, Bit 2 for SD Figure 70. Programmable DAC Gain--Positive and Negative Gain The range of this feature is specified for 7.5% of the nominal output from the DACs. For example, if the output current of the DAC is 4.33 mA, the DAC gain control feature can change this output current from 4.008 mA (-7.5%) to 4.658 mA (+7.5%). Using Subaddress 0x88, Bit 2, double buffering can be activated on the following SD registers: the SD Gamma A and Gamma B curves, SD Y scale, SD Cr scale, SD Cb scale, SD brightness, SD closed captioning, and SD Macrovision Bits[5:0] (Subaddress 0xE0, Bits[5:0]). Rev. J | Page 58 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 The reset value of the control registers is 0x00; that is, nominal DAC current is output. Table 50 is an example of how the output current of the DACs varies for a nominal 4.33 mA output current. Table 50. DAC Gain Control Subaddress 0x0B 0100 0000 (0x40) 0011 1111 (0x3F) 0011 1110 (0x3E) ... ... 0000 0010 (0x02) 0000 0001 (0x01) 0000 0000 (0x00) DAC Current (mA) 4.658 4.653 4.648 ... ... 4.43 4.38 4.33 % Gain 7.5000% 7.3820% 7.3640% ... ... 0.0360% 0.0180% 0.0000% 1111 1111 (0xFF) 1111 1110 (0xFE) ... ... 1100 0010 (0xC2) 1100 0001 (0xC1) 1100 0000 (0xC0) 4.25 4.23 ... ... 4.018 4.013 4.008 -0.0180% -0.0360% ... ... -7.3640% -7.3820% -7.5000% Note Reset value, nominal Gamma correction is performed on the luma data only. The user can choose one of two correction curves, Curve A or Curve B. Only one of these curves can be used at a time. For ED/HD gamma correction, curve selection is controlled using Subaddress 0x35, Bit 4. For SD gamma correction, curve selection is controlled using Subaddress 0x88, Bit 7. The shape of the gamma correction curve is controlled by defining the curve response at 10 different locations along the curve. By altering the response at these locations, the shape of the gamma correction curve can be modified. Between these points, linear interpolation is used to generate intermediate values. Considering the curve to have a total length of 256 points, the 10 programmable locations are at the following points: 24, 32, 48, 64, 80, 96, 128, 160, 192, and 224. The following locations are fixed and cannot be changed: 0, 16, 240, and 255. From the curve locations, 16 to 240, the values at the programmable locations and, therefore, the response of the gamma correction curve, should be calculated to produce the following result: xDESIRED = (xINPUT) where: xDESIRED is the desired gamma corrected output. xINPUT is the linear input signal. is the gamma correction factor. GAMMA CORRECTION Subaddress 0x44 to Subaddress 0x57 for ED/HD; Subaddress 0xA6 to Subaddress 0xB9 for SD Generally, gamma correction is applied to compensate for the nonlinear relationship between signal input and output brightness level (as perceived on a CRT). It can also be applied wherever nonlinear processing is used. Gamma correction uses the function SignalOUT = (SignalIN) where is the gamma correction factor. Gamma correction is available for SD and ED/HD video. For both variations, there are twenty 8-bit registers. They are used to program Gamma Correction Curve A and Gamma Correction Curve B. To program the gamma correction registers, calculate the 10 programmable curve values using the following formula: n - 16 n = x (240 - 16) + 16 240 - 16 where: n is the value to be written into the gamma correction register for point n on the gamma correction curve. n = 24, 32, 48, 64, 80, 96, 128, 160, 192, or 224. is the gamma correction factor. For example, setting = 0.5 for all programmable curve data points results in the following yn values: y24 = [(8/224)0.5 x 224] + 16 = 58 ED/HD gamma correction is enabled using Subaddress 0x35, Bit 5. ED/HD Gamma Correction Curve A is programmed at Subaddress 0x44 to Subaddress 0x4D, and ED/HD Gamma Correction Curve B is programmed at Subaddress 0x4E to Subaddress 0x57. y32 = [(16/224)0.5 x 224] + 16 = 76 y48 = [(32/224)0.5 x 224] + 16 = 101 y64 = [(48/224)0.5 x 224] + 16 = 120 y80 = [(64/224)0.5 x 224] + 16 = 136 SD gamma correction is enabled using Subaddress 0x88, Bit 6. SD Gamma Correction Curve A is programmed at Subaddress 0xA6 to Subaddress 0xAF, and SD Gamma Correction Curve B is programmed at Subaddress 0xB0 to Subaddress 0xB9. y96 = [(80/224)0.5 x 224] + 16 = 150 y128 = [(112/224)0.5 x 224] + 16 = 174 y160 = [(144/224)0.5 x 224] + 16 = 195 y192 = [(176/224)0.5 x 224] + 16 = 214 y224 = [(208/224)0.5 x 224] + 16 = 232 where the sum of each equation is rounded to the nearest integer. Rev. J | Page 59 of 107 ADV7390/ADV7391/ADV7392/ADV7393 enabled (Subaddress 0x31, Bit 7 = 1) and the ED/HD adaptive filter must be disabled (Subaddress 0x35, Bit 7 = 0). The gamma curves in Figure 71 and Figure 72 are examples only; any user-defined curve in the range from 16 to 240 is acceptable. 250 SIGNAL OUTPUT ED/HD Adaptive Filter Mode 200 In ED/HD adaptive filter mode, the following registers are used: 0.5 150 100 SIGNAL INPUT 50 0 0 50 100 150 LOCATION 200 250 06234-072 GAMMA CORRECTED AMPLITUDE To select one of the 256 individual responses, the corresponding gain values, ranging from -8 to +7 for each filter, must be programmed into the ED/HD sharpness filter gain register at Subaddress 0x40. GAMMA CORRECTION BLOCK OUTPUT TO A RAMP INPUT 300 Figure 71. Signal Input (Ramp) and Signal Output for Gamma 0.5 GAMMA CORRECTION BLOCK TO A RAMP INPUT FOR VARIOUS GAMMA VALUES 250 0.3 200 0.5 150 100 SI AL GN T PU IN 0 50 1.8 100 150 LOCATION ED/HD Adaptive Filter Threshold A ED/HD Adaptive Filter Threshold B ED/HD Adaptive Filter Threshold C ED/HD Adaptive Filter Gain 1 ED/HD Adaptive Filter Gain 2 ED/HD Adaptive Filter Gain 3 ED/HD sharpness filter gain To activate the adaptive filter control, the ED/HD sharpness filter and the ED/HD adaptive filter must be enabled (Subaddress 0x31, Bit 7 = 1, and Subaddress 0x35, Bit 7 = 1, respectively). The edges can then be attenuated with the settings in the ED/HD adaptive filter (Gain 1, Gain 2, and Gain 3) registers (Subaddress 0x58, Subaddress 0x59 and Subaddress 0x5A), and the ED/HD sharpness filter gain register (Subaddress 0x40). 1.5 50 0 * * * * * * * The derivative of the incoming signal is compared to the three programmable threshold values: ED/HD adaptive filter (Threshold A, Threshold B, and Threshold C) registers (Subaddress 0x5B, Subaddress 0x5C, and Subaddress 0x5D). The recommended threshold range is 16 to 235, although any value in the range of 0 to 255 can be used. 200 250 06234-073 GAMMA CORRECTED AMPLITUDE 300 Data Sheet Figure 72. Signal Input (Ramp) and Selectable Output Curves There are two adaptive filter modes available. The mode is selected using the ED/HD adaptive filter mode control (Subaddress 0x35, Bit 6) as follows: * ED/HD SHARPNESS FILTER AND ADAPTIVE FILTER CONTROLS Subaddress 0x40; Subaddress 0x58 to Subaddress 0x5D There are three filter modes available on the ADV7390/ADV7391/ ADV7392/ADV7393: sharpness filter mode and two adaptive filter modes. * ED/HD Sharpness Filter Mode To enhance or attenuate the Y signal in the frequency ranges shown in Figure 73, the ED/HD sharpness filter must be Rev. J | Page 60 of 107 Mode A is used when the ED/HD adaptive filter mode control is set to 0. In this case, Filter B (LPF) is used in the adaptive filter block. In addition, only the programmed values for Gain B in the ED/HD sharpness filter gain register and ED/HD adaptive filter (Gain 1, Gain 2, and Gain 3) registers are applied when needed. The Gain A values are fixed and cannot be changed. Mode B is used when ED/HD adaptive filter mode control is set to 1. In this mode, a cascade of Filter A and Filter B is used. Both settings for Gain A and Gain B in the ED/HD sharpness filter gain register and ED/HD adaptive filter (Gain 1, Gain 2, and Gain 3) registers become active when needed. ADV7390/ADV7391/ADV7392/ADV7393 1.4 1.3 1.3 1.2 1.2 MAGNITUDE MAGNITUDE INPUT SIGNAL STEP 1.4 1.1 1.0 0.9 1.1 1.0 0.9 0.8 0.8 0.7 0.7 0.6 0.6 0.5 MAGNITUDE RESPONSE (Linear Scale) SHARPNESS AND ADAPTIVE FILTER CONTROL BLOCK 1.5 1.5 0.5 FREQUENCY (MHz) FILTER A RESPONSE (Gain Ka) 1.6 1.5 1.4 1.3 1.2 1.1 1.0 FREQUENCY (MHz) FILTER B RESPONSE (Gain Kb) 0 2 6 8 4 10 FREQUENCY (MHz) 12 FREQUENCY RESPONSE IN SHARPNESS FILTER MODE WITH Ka = 3 AND Kb = 7 06234-074 Data Sheet Figure 73. ED/HD Sharpness and Adaptive Filter Control d a R2 1 e b R4 R1 f c Block R2 CH1 500mV REF A 500mV 4.00s M 4.00s 1 9.99978ms CH1 ALL FIELDS CH1 500mV REF A 500mV 4.00s 1 M 4.00s 9.99978ms CH1 ALL FIELDS 06234-075 1 Figure 74. ED/HD Sharpness Filter Control with Different Gain Settings for ED/HD Sharpness Filter Gain Values ED/HD SHARPNESS FILTER AND ADAPTIVE FILTER APPLICATION EXAMPLES Sharpness Filter Application The ED/HD sharpness filter can be used to enhance or attenuate the Y video output signal. The register settings in Table 51 are used to achieve the results shown in Figure 74. Input data is generated by an external signal source. 1 Register Setting 0xFC 0x10 0x20 0x00 0x81 0x00 0x08 0x04 0x40 0x80 0x22 Reference1 a b c d e f The register settings in Table 52 are used to obtain the results shown in Figure 76, that is, to remove the ringing on the input Y signal, as shown in Figure 75. Input data is generated by an external signal source. Table 52. Register Settings for Figure 76 Table 51. ED/HD Sharpness Control Settings for Figure 74 Subaddress 0x00 0x01 0x02 0x30 0x31 0x40 0x40 0x40 0x40 0x40 0x40 Adaptive Filter Control Application Subaddress 0x00 0x01 0x02 0x30 0x31 0x35 0x40 0x58 0x59 0x5A 0x5B 0x5C 0x5D See Figure 74. Rev. J | Page 61 of 107 Register Setting 0xFC 0x38 0x20 0x00 0x81 0x80 0x00 0xAC 0x9A 0x88 0x28 0x3F 0x64 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet In DNR mode, if the absolute value of the filter output is smaller than the threshold, it is assumed to be noise. A programmable amount (coring gain border, coring gain data) of this noise signal is subtracted from the original signal. In DNR sharpness mode, if the absolute value of the filter output is less than the programmed threshold, it is assumed to be noise as before. However, if the level exceeds the threshold, now being identified as a valid signal, a fraction of the signal (coring gain border, coring gain data) is added to the original signal to boost high frequency components and sharpen the video image. 06234-076 In MPEG systems, it is common to process the video information in blocks of 8 pixels x 8 pixels for MPEG2 systems or 16 pixels x 16 pixels for MPEG1 systems (block size control). DNR can be applied to the resulting block transition areas known to contain noise. Generally, the block transition area contains two pixels. It is possible to define this area to contain four pixels (border area). Figure 75. Input Signal to ED/HD Adaptive Filter It is also possible to compensate for variable block positioning or differences in YCrCb pixel timing with the use of the DNR block offset. The digital noise reduction registers are three 8-bit registers. They are used to control the DNR processing. DNR MODE DNR CONTROL 06234-077 BLOCK SIZE CONTROL BORDER AREA BLOCK OFFSET GAIN Figure 76. Output Signal from ED/HD Adaptive Filter (Mode A) NOISE SIGNAL PATH When the adaptive filter mode is changed to Mode B (Subaddress 0x35, Bit 6), the output shown in Figure 77 can be obtained. CORING GAIN DATA CORING GAIN BORDER INPUT FILTER BLOCK FILTER OUTPUT < THRESHOLD? Y DATA INPUT FILTER OUTPUT > THRESHOLD - SUBTRACT SIGNAL IN THRESHOLD RANGE FROM ORIGINAL SIGNAL + DNR OUT MAIN SIGNAL PATH DNR SHARPNESS MODE DNR CONTROL BLOCK SIZE CONTROL BORDER AREA BLOCK OFFSET GAIN 06234-078 NOISE SIGNAL PATH CORING GAIN DATA CORING GAIN BORDER INPUT FILTER BLOCK SD DIGITAL NOISE REDUCTION Y DATA INPUT Subaddress 0xA3 to Subaddress 0xA5 Digital noise reduction (DNR) is applied to the Y data only. A filter block selects the high frequency, low amplitude components of the incoming signal (DNR input select). The absolute value of the filter output is compared to a programmable threshold value (DNR threshold control). There are two DNR modes available: DNR mode and DNR sharpness mode. Rev. J | Page 62 of 107 ADD SIGNAL ABOVE THRESHOLD RANGE FROM ORIGINAL SIGNAL FILTER OUTPUT > THRESHOLD? FILTER OUTPUT < THRESHOLD + + MAIN SIGNAL PATH Figure 78. SD DNR Block Diagram DNR OUT 06234-079 Figure 77. Output Signal from ED/HD Adaptive Filter (Mode B) Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Coring Gain Border--Subaddress 0xA3, Bits[3:0] Block Size--Subaddress 0xA4, Bit 7 These four bits are assigned to the gain factor applied to border areas. In DNR mode, the range of gain values is 0 to 1 in increments of 1/8. This factor is applied to the DNR filter output that lies below the set threshold range. The result is then subtracted from the original signal. This bit is used to select the size of the data blocks to be processed. Setting the block size control function to Logic 1 defines a 16 pixel x 16 pixel data block, and Logic 0 defines an 8 pixel x 8 pixel data block, where one pixel refers to two clock cycles at 27 MHz. In DNR sharpness mode, the range of gain values is 0 to 0.5 in increments of 1/16. This factor is applied to the DNR filter output that lies above the threshold range. The result is added to the original signal. DNR Input Select--Subaddress 0xA5, Bits[2:0] These four bits are assigned to the gain factor applied to the luma data inside the MPEG pixel block. In DNR mode, the range of gain values is 0 to 1 in increments of 1/8. This factor is applied to the DNR filter output that lies below the set threshold range. The result is then subtracted from the original signal. In DNR sharpness mode, the range of gain values is 0 to 0.5 in increments of 1/16. This factor is applied to the DNR filter output that lies above the threshold range. The result is added to the original signal. FILTER D 0.8 APPLY BORDER CORING GAIN 0 OFFSET CAUSED BY VARIATIONS IN INPUT TIMING FILTER B OXXXXXXOOXXXXXXO DNR Threshold--Subaddress 0xA4, Bits[5:0] These six bits are used to define the threshold value in the range of 0 to 63. The range is an absolute value. Border Area--Subaddress 0xA4, Bit 6 When this bit is set to Logic 1, the block transition area can be defined to consist of four pixels. If this bit is set to Logic 0, the border transition area consists of two pixels, where one pixel refers to two clock cycles at 27 MHz. TWO-PIXEL BORDER DATA 0 1 2 3 4 FREQUENCY (MHz) 5 6 Figure 81. SD DNR Input Select Figure 79. SD DNR Offset Control DNR Mode--Subaddress 0xA5, Bit 3 This bit controls the DNR mode selected. Logic 0 selects DNR mode; Logic 1 selects DNR sharpness mode. DNR works on the principle of defining low amplitude, high frequency signals as probable noise and subtracting this noise from the original signal. In DNR mode, it is possible to subtract a fraction of the signal that lies below the set threshold, assumed to be noise, from the original signal. The threshold is set in DNR Register 1. When DNR sharpness mode is enabled, it is possible to add a fraction of the signal that lies above the set threshold to the original signal because this data is assumed to be valid data and not noise. The overall effect is that the signal is boosted (similar to using the extended SSAF filter). Block Offset Control--Subaddress 0xA5, Bits[7:4] 8 x 8 PIXEL BLOCK 8 x 8 PIXEL BLOCK 06234-081 720 x 485 PIXELS (NTSC) 0.4 FILTER A 06234-080 DNR27 TO DNR24 = 0x01 0.6 0.2 OXXXXXXOOXXXXXXO OXXXXXXOOXXXXXXO FILTER C 06234-082 APPLY DATA CORING GAIN 1.0 MAGNITUDE Coring Gain Data--Subaddress 0xA3, Bits[7:4] These three bits are assigned to select the filter that is applied to the incoming Y data. The signal that lies in the pass band of the selected filter is the signal processed by DNR. Figure 81 shows the filter responses selectable with this control. Four bits are assigned to this control, which allows a shift in the data block of 15 pixels maximum. The coring gain positions are fixed. The block offset shifts the data in steps of one pixel such that the border coring gain factors can be applied at the same position regardless of variations in input timing of the data. Figure 80. SD DNR Border Area Rev. J | Page 63 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet SD ACTIVE VIDEO EDGE CONTROL three pixels of the active video on the luma channel are scaled so that maximum transitions on these pixels are not possible. Subaddress 0x82, Bit 7 At the start of active video, the first three pixels are multiplied by 1/8, 1/2, and 7/8, respectively. Approaching the end of active video, the last three pixels are multiplied by 7/8, 1/2, and 1/8, respectively. All other active video pixels pass through unprocessed. The ADV7390/ADV7391/ADV7392/ADV7393 are able to control fast rising and falling signals at the start and end of active video to minimize ringing. When the active video edge control feature is enabled (Subaddress 0x82, Bit 7 = 1), the first three pixels and the last LUMA CHANNEL WITH ACTIVE VIDEO EDGE DISABLED LUMA CHANNEL WITH ACTIVE VIDEO EDGE ENABLED 100 IRE 100 IRE 87.5 IRE 50 IRE 0 IRE 06234-083 12.5 IRE 0 IRE Figure 82. Example of Active Video Edge Functionality VOLTS IRE:FLT 100 0.5 50 0 F2 L135 -50 0 2 4 6 8 10 12 06234-084 0 Figure 83. Example of Video Output with Subaddress 0x82, Bit 7 = 0 VOLTS IRE:FLT 100 0.5 50 0 F2 L135 -50 -2 0 2 4 6 8 10 Figure 84. Example of Video Output with Subaddress 0x82, Bit 7 = 1 Rev. J | Page 64 of 107 12 06234-085 0 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 EXTERNAL HORIZONTAL AND VERTICAL SYNCHRONIZATION CONTROL For timing synchronization purposes, the ADV7390/ADV7391/ADV7392/ADV7393 are able to accept either EAV/SAV time codes embedded in the input pixel data or external synchronization signals provided on the HSYNC and VSYNC pins (see Table 53). It is also possible to output synchronization signals on the HSYNC and VSYNC pins (see Table 54 to Table 56). Table 53. Timing Synchronization Signal Input Options Signal SD HSYNC In SD VSYNC/FIELD In ED/HD HSYNC In ED/HD VSYNC/FIELD In 1 Pin HSYNC VSYNC HSYNC VSYNC Condition SD slave timing (Mode 1, Mode 2, or Mode 3) selected (Subaddress 0x8A[2:0])1 SD slave timing (Mode 1, Mode 2, or Mode 3) selected (Subaddress 0x8A[2:0])1 ED/HD timing synchronization inputs enabled (Subaddress 0x30, Bit 2 = 0) ED/HD timing synchronization inputs enabled (Subaddress 0x30, Bit 2 = 0) SD and ED/HD timing synchronization outputs must also be disabled (Subaddress 0x02[7:6] = 00). Table 54. Timing Synchronization Signal Output Options Signal SD HSYNC Out SD VSYNC/FIELD Out ED/HD HSYNC Out ED/HD VSYNC/FIELD Out 1 2 Pin HSYNC VSYNC HSYNC VSYNC Condition SD timing synchronization outputs enabled (Subaddress 0x02, Bit 6 = 1)1 SD timing synchronization outputs enabled (Subaddress 0x02, Bit 6 = 1)1 ED/HD timing synchronization outputs enabled (Subaddress 0x02, Bit 7 = 1)2 ED/HD timing synchronization outputs enabled (Subaddress 0x02, Bit 7 = 1)2 ED/HD timing synchronization outputs must also be disabled (Subaddress 0x02, Bit 7 = 0). ED/HD timing synchronization inputs must also be disabled; that is, embedded EAV/SAV timing codes must be enabled (Subaddress 0x30, Bit 2 = 1). Table 55. HSYNC Output Control1, 2 ED/HD Input Sync Format (Subaddress 0x30, Bit 2) X X ED/HD HSYNC Control (Subaddress 0x34, Bit 1) X X ED/HD Sync Output Enable (Subaddress 0x02, Bit 7) 0 0 SD Sync Output Enable (Subaddress 0x02, Bit 6) 0 1 Tristate Pipelined SD HSYNC 0 0 1 X Pipelined ED/HD HSYNC 1 0 1 X X 1 1 X Pipelined ED/HD HSYNC based on AV Code H bit Pipelined ED/HD HSYNC based on horizontal counter 1 2 Signal on HSYNC Pin Duration N/A See the SD Timing section. As per HSYNC timing. Same as line blanking interval. Same as embedded HSYNC. In all ED/HD standards where there is an HSYNC output, the start of the HSYNC pulse is aligned with the falling edge of the embedded HSYNC in the output video. X = don't care. Table 56. VSYNC Output Control 1, 2 ED/HD Input Sync Format (Subaddress 0x30, Bit 2) x x ED/HD VSYNC Control (Subaddress 0x34, Bit 2) x x ED/HD Sync Output Enable (Subaddress 0x02, Bit 7) 0 0 SD Sync Output Enable (Subaddress 0x02, Bit 6) 0 1 Video Standard x Interlaced Signal on VSYNC Pin 0 0 1 x x 1 0 1 x 1 0 1 x All HD interlaced standards All ED/HD progressive standards Pipelined ED/HD VSYNC or field signal Pipelined field signal based on AV Code F bit Pipelined VSYNC based on AV Code V bit Rev. J | Page 65 of 107 Tristate Pipelined SD VSYNC/field Duration N/A See the SD Timing section. As per VSYNC or field signal timing. Field. Vertical blanking interval. ADV7390/ADV7391/ADV7392/ADV7393 ED/HD Input Sync Format (Subaddress 0x30, Bit 2) X ED/HD VSYNC Control (Subaddress 0x34, Bit 2) 1 ED/HD Sync Output Enable (Subaddress 0x02, Bit 7) 1 SD Sync Output Enable (Subaddress 0x02, Bit 6) X X 1 1 X 1 2 Data Sheet Video Standard All ED/HD standards except 525p 525p Signal on VSYNC Pin Pipelined ED/HD VSYNC based on the vertical counter Pipelined ED/HD VSYNC based on the vertical counter Duration Aligned with serration lines. Vertical blanking interval. In all ED/HD standards where there is a VSYNC output, the start of the VSYNC pulse is aligned with the falling edge of the embedded VSYNC in the output video. X = don't care. LOW POWER MODE DAC AUTOPOWER-DOWN Subaddress 0x0D, Bits[2:0] Subaddress 0x10, Bit 4 For power-sensitive applications, the ADV7390/ADV7391/ ADV7392/ADV7393 support an Analog Devices, Inc., proprietary low power mode of operation. To use this low power mode, the DACs must be operating in full-drive mode (RSET = 510 , RL = 37.5 ). Low power mode is not available in low-drive mode (RSET = 4.12 k, RL = 300 ). Low power mode can be independently enabled or disabled on each DAC using Subaddress 0x0D, Bits[2:0]. Low power mode is disabled by default on all DACs. For power-sensitive applications, a DAC autopower-down feature can be enabled using Subaddress 0x10, Bit 4. This feature is available only when the cable detection feature is enabled. In low-power mode, DAC current consumption is content dependent and, on a typical video stream, it can be reduced by as much as 40%. For applications requiring the highest possible video performance, low power mode should be disabled. CABLE DETECTION Subaddress 0x10, Bits[1:0] The ADV7390/ADV7391/ADV7392/ADV7393 include an Analog Devices proprietary cable detection feature. The cable detection feature is available on DAC 1 and DAC 2 when operating in full-drive mode (RSET = 510 , RL = 37.5 , assuming a connected cable). The feature is not available in lowdrive mode (RSET = 4.12 k, RL = 300 ). For a DAC to be monitored, the DAC must be powered up in Subaddress 0x00. The cable detection feature can be used with all SD, ED, and HD video standards. It is available for all output configurations, that is, CVBS, Y-C, YPrPb, and RGB output configurations. For CVBS/Y-C output configurations, both DAC 1 and DAC 2 are monitored; that is, the CVBS and Y-C luma outputs are monitored. For YPrPb and RGB output configurations, only DAC 1 is monitored; that is, the luma or green output is monitored. Once per frame, the ADV7390/ADV7391/ADV7392/ADV7393 monitor DAC 1 and/or DAC 2, updating Subaddress 0x10, Bit 0 and/or Bit 1, respectively. If a cable is detected on one of the DACs, the relevant bit is set to 0. If not, the bit is set to 1. With this feature enabled, the cable detection circuitry monitors DAC 1 and/or DAC 2 once per frame and, if they are unconnected, automatically powers down some or all of the DACs. Which DAC or DACs are powered down depends on the selected output configuration. For CVBS/Y-C output configurations, if DAC 1 is unconnected, only DAC 1 powers down. If DAC 2 is unconnected, DAC 2 and DAC 3 power down. For YPrPb and RGB output configurations, if DAC 1 is unconnected, all three DACs are powered down. DAC 2 is not monitored for YPrPb and RGB output configurations. Once per frame, DAC 1 and/or DAC 2 is monitored. If a cable is detected, the appropriate DAC or DACs remain powered up for the duration of the frame. If no cable is detected, the appropriate DAC or DACs power down until the next frame, when the process is repeated. SLEEP MODE Subaddress 0x00, Bit 0 In sleep mode, most of the digital I/O pins of the ADV7390/ ADV7391/ADV7392/ADV7393 are disabled. For inputs, this means that the external data is ignored, and internally the logic normally driven by a given input is just tied low or high. This includes CLKIN. For digital output pins, this means that the pin goes into tristate (high impedance) mode. There are some exceptions to allow the user to continue to communicate with the part via I2C: the RESET, ALSB, SDA and SCL pins are kept alive. Most of the analogue circuitry is powered down when in sleep mode. In addition, the cable detect feature no longer works as the DACs are powered down. Sleep mode is enabled using Subaddress 0x00, Bit 0. Rev. J | Page 66 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 PIXEL AND CONTROL PORT READBACK SD TELETEXT INSERTION Subaddress 0x13, Subaddress 0x14, Subaddress 0x16 Subaddress 0xC9 to Subaddress 0xCE The ADV7390/ADV7391/ADV7392/ADV7393 support the readback of most digital inputs via the I2C MPU port. This feature is useful for board-level connectivity testing with upstream devices. The ADV7390/ADV7391/ADV7392/ADV7393 support the insertion of teletext data, using a two pin interface, when operating in PAL mode. Teletext insertion is enabled using Subaddress 0xC9, Bit 0. The pixel port (P[15:0] or P[7:0]), HSYNC, VSYNC, and SFL are available for readback via the MPU port. The readback registers are located at Subaddress 0x13, Subaddress 0x14, and Subaddress 0x16. In accordance with the PAL WST teletext standard, teletext data should be inserted into the ADV7390/ADV7391/ADV7392/ ADV7393 at a rate of 6.9375 Mbps. On the ADV7390/ADV7391, the teletext data is inserted on the VSYNC pin. On the ADV7392/ADV7393, the teletext data can be inserted on the VSYNC or P0 pin (selectable through Subaddress 0xC9, Bit 2). When using this feature, apply a clock signal to the CLKIN pin to register the levels applied to the input pins. The SD input mode (Subaddress 0x01, Bits[6:4] = 000) must be selected when using this feature. When teletext insertion is enabled, a teletext request signal is output from the ADV7390/ADV7391/ADV7392/ADV7393 to indicate when teletext data should be inserted. The teletext request signal is output on the SFL pin. The position (relative to the teletext data) and width of the request signal are configurable using Subaddress 0xCA. The request signal can operate in either a line or bit mode. The request signal mode is controlled using Subaddress 0xC9, Bit 1. RESET MECHANISMS Subaddress 0x17, Bit 1 A hardware reset is activated with a high-to-low transition on the RESET pin in accordance with the timing specifications. This resets all registers to their default values. After a hardware reset, the MPU port is configured for I2C operation. For correct device operation, a hardware reset is necessary after power-up. To account for the noninteger relationship between the teletext insertion rate (6.9375 Mbps) and the pixel clock (27 MHz), a teletext insertion protocol is implemented in the ADV7390/ ADV7391/ADV7392/ADV7393. At a rate of 6.9375 Mbps, the time taken for the insertion of 37 teletext bits equates to 144 pixel clock cycles (at 27 MHz). For every 37 teletext bits inserted into the ADV7390/ADV7391/ADV7392/ADV7393, the 10th, 19th, 28th, and 37th bits are carried for three pixel clock cycles, and the remainder are carried for four pixel clock cycles (totaling 144 pixel clock cycles). The teletext insertion protocol repeats every 37 teletext bits or 144 pixel clock cycles until all 360 teletext bits are inserted. The ADV7390/ADV7391/ADV7392/ADV7393 also have a software reset accessible via the I2C MPU port. A software reset is activated by writing a 1 to Subaddress 0x17, Bit 1. This resets all registers to their default values. This bit is self-clearing; that is, after a 1 has been written to the bit, the bit automatically returns to 0. A hardware reset is necessary after power-up for correct device operation. If no hardware reset functionality is required by the application, the RESET pin can be connected to an RC network to provide the hardware reset necessary after power-up. After power-up, the time constant of the RC network holds the RESET pin low long enough to cause a reset to take place. All subsequent resets can be done via software. 45 BYTES (360 BITS) - PAL RUN-IN CLOCK Figure 85. Teletext VBI Line Rev. J | Page 67 of 107 06234-143 ADDRESS AND DATA TELETEXT VBI LINE ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet tSYNTTXOUT CVBS/Y tPD tPD HSYNC 10.2s TTXDATA TTXDEL TTXREQ PROGRAMMABLE PULSE EDGES tSYNTTXOUT = 10.2s. tPD = PIPELINE DELAY THROUGH ADV7390/ADV7391/ADV7392/ADV7393. TTXDEL = TTXREQ TO TTXDATA (PROGRAMMABLE RANGE = 4 BITS [0 TO 15 PIXEL CLOCK CYCLES]). Figure 86. Teletext Functionality Diagram Rev. J | Page 68 of 107 06234-144 TTXST Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 PRINTED CIRCUIT BOARD LAYOUT AND DESIGN UNUSED PINS If the HSYNC and VSYNC pins are not used, they should be tied to VDD_IO through a pull-up resistor (10 k or 4.7 k). Any other unused digital inputs should be tied to ground. Unused digital output pins should be left floating. DAC outputs can either be left floating or connected to GND. Disabling these outputs is recommended. DAC CONFIGURATIONS Table 57. ADV7390/ADV7391/ADV7392/ADV7393 Output Rates Input Mode (Subaddress 0x01, Bits[6:4]) SD ED The ADV7390/ADV7391/ADV7392/ADV7393 contain three DACs. All three DACs can be configured to operate in fulldrive mode. Full-drive mode is defined as 34.7 mA full-scale current into a 37.5 load, RL. Full drive is the recommended mode of operation for the DACs. Alternatively, all three DACs can be configured to operate in lowdrive mode. Low-drive mode is defined as 4.33 mA full-scale current into a 300 load, RL. The ADV7390/ADV7391/ADV7392/ADV7393 contain an RSET pin. A resistor connected between the RSET pin and AGND is used to control the full-scale output current and, therefore, the output voltage levels of DAC 1, DAC 2, and DAC 3. For fulldrive operation, RSET must have a value of 510 and RL must have a value of 37.5 . For low drive operation, RSET must have a value of 4.12 k, and RL must have a value of 300 . The resistor connected to the RSET pin should have a 1% tolerance. The ADV7390/ADV7391/ADV7392/ADV7393 contain a compensation pin, COMP. A 2.2 nF compensation capacitor should be connected from the COMP pin to VAA. VIDEO OUTPUT BUFFER AND OPTIONAL OUTPUT FILTER HD Oversampling Off On On Off On On Off On On Output Rate (MHz) 27 (2x) 108 (8x) 216 (16x) 27 (1x) 108 (4x) 216 (8x) 74.25 (1x) 148.5 (2x) 297 (4x) Table 58. Output Filter Requirements Application SD ED HD Cutoff Frequency (MHz) > 6.5 > 6.5 > 6.5 > 12.5 > 12.5 > 12.5 > 30 > 30 > 30 Oversampling 2x 8x 16x 1x 4x 8x 1x 2x 4x Attenuation -50 dB at (MHz) 20.5 101.5 209.5 14.5 95.5 203.5 44.25 118.5 267 10H DAC OUTPUT 3 600 22pF 75 600 BNC OUTPUT 1 4 An optional reconstruction (anti-imaging) low-pass filter (LPF) may be required on the ADV7390/ADV7391/ADV7392/ADV7393 DAC outputs. The filter specifications vary with the application. The use of 16x (SD), 8x (ED), or 4x (HD) oversampling can remove the requirement for a reconstruction filter altogether. For applications requiring an output buffer and reconstruction filter, the ADA4430-1 and ADA4411-3 integrated video filter buffers should be considered. 06234-086 560 560 Figure 87. Example of Output Filter for SD, 16x Oversampling 4.7H DAC OUTPUT 3 6.8pF 600 600 6.8pF 75 1 BNC OUTPUT 4 560 560 06234-087 An output buffer is necessary on any DAC that operates in lowdrive mode (RSET = 4.12 k, RL = 300 ). Analog Devices produces a range of op amps suitable for this application, for example, the AD8061. For more information about line driver buffering circuits, see the relevant op amp data sheet. Figure 88. Example of Output Filter for ED, 8x Oversampling DAC OUTPUT 3 300 1 4 75 390nH BNC OUTPUT 3 33pF 33pF 75 1 500 500 Figure 89. Example of Output Filter for HD, 4x Oversampling Rev. J | Page 69 of 107 06234-088 4 ADV7390/ADV7391/ADV7392/ADV7393 CIRCUIT FREQUENCY RESPONSE 0 PRINTED CIRCUIT BOARD (PCB) LAYOUT 0 24n The ADV7390/ADV7391/ADV7392/ADV7393 are highly integrated circuits containing both precision analog and high speed digital circuitry. It is designed to minimize interference effects on the integrity of the analog circuitry by the high speed digital circuitry. It is imperative that these same design and layout techniques be applied to the system-level design so that optimal performance is achieved. -30 -10 21n MAGNITUDE (dB) -60 -20 18n -90 -30 PHASE (Degrees) 15n -120 -40 12n -150 -50 9n -180 GROUP DELAY (Seconds) -60 6n -210 -70 -80 1M 3n -240 0 1G 10M 100M FREQUENCY (Hz) 06234-089 GAIN (dB) Data Sheet Figure 90. Output Filter Plot for SD, 16x Oversampling 480 Component placement should be carefully considered to separate noisy circuits, such as clock signals and high speed digital circuitry, from analog circuitry. 18n 400 -10 MAGNITUDE (dB) 16n -20 320 -30 240 GAIN (dB) 14n PHASE (Degrees) GROUP DELAY (Seconds) -40 The external loop filter components and components connected to the COMP and RSET pins should be placed as close as possible to, and on the same side of the PCB as, the ADV7390/ADV7391/ ADV7392/ADV7393. Adding vias to the PCB to get the components closer to the ADV7390/ADV7391/ADV7392/ ADV7393 is not recommended. 12n 160 10n -50 80 -60 0 -70 -80 -80 -160 8n 6n 4n 2n 10M -240 0 1G 100M 06234-090 -90 1M FREQUENCY (Hz) Figure 91. Output Filter Plot for ED, 8x Oversampling CIRCUIT FREQUENCY RESPONSE 0 PHASE (Degrees) 200 -10 40 -30 -40 -40 -120 -50 -200 10 100 FREQUENCY (MHz) Figure 92. Output Filter Plot for HD, 4x Oversampling The termination resistors on the DAC output traces should be placed as close as possible to and on the same side of the PCB as the ADV7390/ADV7391/ADV7392/ADV7393. The termination resistors should overlay the PCB ground plane. Power Supplies 06234-091 GAIN (dB) GROUP DELAY (Seconds) PHASE (Degrees) 120 -20 It is recommended that the ADV7390/ADV7391/ADV7392/ ADV7393 be placed as close as possible to the output connector, with the DAC output traces as short as possible. External filter and buffer components connected to the DAC outputs should be placed as close as possible to the ADV7390/ ADV7391/ADV7392/ADV7393 to minimize the possibility of noise pickup from neighboring circuitry and to minimize the effect of trace capacitance on output bandwidth. This is particularly important when operating in low-drive mode (RSET = 4.12 k, RL = 300 ). MAGNITUDE (dB) 1 It is recommended to use a 4-layer printed circuit board with ground and power planes separating the signal trace layer and the solder side layer. Component Placement CIRCUIT FREQUENCY RESPONSE 0 The layout should be optimized for lowest noise on the ADV7390/ADV7391/ADV7392/ADV7393 power and ground planes by shielding the digital inputs and providing good power supply decoupling. It is recommended that a separate regulated supply be provided for each power domain (VAA, VDD, VDD_IO, and PVDD). For optimal performance, linear regulators rather than switch mode regulators should be used. If switch mode regulators must be used, care must be taken with regard to the quality of the output voltage in terms of ripple and noise. This is particularly true for the VAA and PVDD power domains. Each power supply should be individually connected to the system power supply at a single point through a suitable filtering device, such as a ferrite bead. Rev. J | Page 70 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Power Supply Decoupling It is recommended that each power supply pin be decoupled with 10 nF and 0.1 F ceramic capacitors. The VAA, PVDD, VDD_IO, and both VDD pins should be individually decoupled to ground. The decoupling capacitors should be placed as close as possible to the ADV7390/ADV7391/ADV7392/ADV7393 with the capacitor leads kept as short as possible to minimize lead inductance. A 1 F tantalum capacitor is recommended across the VAA supply in addition to the 10 nF and 0.1 F ceramic capacitors. Power Supply Sequencing The ADV7390/ADV7391/ADV7392/ADV7393 are robust to all power supply sequencing combinations. Any sequence can be used. However, all power supplies should settle to their nominal voltages within one second. Digital Signal Interconnect The digital signal traces should be isolated as much as possible from the analog outputs and other analog circuitry. Digital signal traces should not overlay the VAA or PVDD power plane. ADDITIONAL LAYOUT CONSIDERATIONS FOR THE WLCSP PACKAGE Due to the high pad density and 0.5 mm pitch of the WLCSP, it is not recommended that connections to inner bumps be routed on the top PCB layer only. The traces (track and space) must fit within the limits of the solder mask openings. Routing all traces on the top surface layer of the board, while possible, is usually not a feasible solution due to the limitations of the geometries imposed by the board fabrication technology. Given a pitch of 0.5 mm with a typical solder mask opening diameter of 0.35 mm, there is only a 0.15 mm distance between the solder mask openings. An alternative to routing on the top surface is to route out on buried layers. To achieve this, the pads are connected to the lower layers using microvias. See the AN-617 Application Note, MicroCSP Wafer Level Chip Scale Package for additional details about the board layout for the WLCSP package. Due to the high clock rates used, avoid long clock traces to the ADV7390/ADV7391/ADV7392/ADV7393 to minimize noise pickup. Any pull-up termination resistors for the digital inputs should be connected to the VDD_IO power supply. Analog Signal Interconnect DAC output traces should be treated as transmission lines with appropriate measures taken to ensure optimal performance (for example, impedance matched traces). The DAC output traces should be kept as short as possible. The termination resistors on the DAC output traces should be placed as close as possible to, and on the same side of the PCB as, the ADV7390/ADV7391/ ADV7392/ADV7393. To avoid crosstalk between the DAC outputs, it is recommended that as much space as possible be left between the traces connected to the DAC output pins. Adding ground traces between the DAC output traces is also recommended. Rev. J | Page 71 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet TYPICAL APPLICATIONS CIRCUITS FERRITE BEAD 3.3V 33F VDD_IO 10F 0.1F GND_IO GND_IO FERRITE BEAD PVDD 1.8V 33F GND_IO 10F 0.1F PGND PGND FERRITE BEAD V PGND VDD_IO POWER SUPPLY DECOUPLING 0.01F GND_IO PVDD POWER SUPPLY DECOUPLING 0.01F PGND NOTES 1. FOR OPTIMUM PERFORMANCE, EXTERNAL COMPONENTS CONNECTED TO THE COMP, RSET AND DAC OUTPUT PINS SHOULD BE LOCATED CLOSE TO, AND ON THE SAME SIDE OF THE PCB AS, THE ADV7390/ADV7391/ADV7392/ADV7393. 2. THE I2C DEVICE ADDRESS IS CONFIGURABLE USING THE ALSB PIN: ALSB = 0, I2C DEVICE ADDRESS = 0xD4 (ADV7390/ADV7392) OR 0x54 (ADV7391/ADV7393) ALSB = 1, I2C DEVICE ADDRESS = 0xD6 (ADV7390/ADV7392) OR 0x56 (ADV7391/ADV7393) AA 3.3V 33F 10F 0.1F AGND AGND FERRITE BEAD V AGND 0.01F VAA POWER SUPPLY AGND DECOUPLING 1F AGND DD 1.8V 33F DGND 10F 0.1F DGND DGND 0.01F DGND VDD POWER SUPPLY DECOUPLING FOR EACH POWER PIN 3. THE RESISTOR CONNECTED TO THE RSET PIN SHOULD HAVE A 1% TOLERANCE. 4. THE RECOMMENDED MODE OF OPERATION FOR THE DACs IS FULLDRIVE (RSET = 510, RL = 37.5). VAA VDD_IO P0 P1 P2 P3 P4 P5 P6 P7 PVDD VDD VDD VAA 2.2nF COMP RSET ADV7390/ADV7391/ ADV7392/ADV7393 510 AGND PIXEL PORT INPUTS P8 P9 P10 P11 P12 P13 P14 P15 CONTROL INPUTS/OUTPUTS DAC1 TO DAC3 FULL DRIVE OPTION (RECOMMENDED) OPTIONAL LPF DAC 1 ADV7392/ ADV7393 ONLY DAC 1 OPTIONAL LPF DAC 2 DAC1 TO DAC3 LOW DRIVE OPTION DAC 3 DAC 2 DAC 3 RSET 4.12k AGND OPTIONAL LPF 75 75 75 AGND AGND AGND ADA4411-3 75 DAC 1 HSYNC VSYNC DAC 1 LPF 300 CLOCK INPUT CLKIN AGND I2C PORT ADA4411-3 SDA SCL 75 DAC 2 DAC 2 LPF ALSB TIE EITHER LOW OR HIGH 300 RESET AGND EXTERNAL LOOP FILTER ADA4411-3 12nF EXT_LF 150nF 75 DAC 3 DAC 3 LPF 170 300 LOOP FILTER COMPONENTS SHOULD BE LOCATED AGND PGND DGND DGND GND_IO CLOSE TO THE EXT_LF PIN AND ON THE SAME SIDE OF THE PCB AS THE ADV7390/ADV7391/ ADV7392/ADV7393. AGND PGND DGND DGND GND_IO AGND Figure 93. ADV7390/ADV7391/ADV7392/ADV7393 (LFCSP) Typical Applications Circuit Rev. J | Page 72 of 107 06234-092 PVDD Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 FERRITE BEAD 3.3V 33F VDD_IO 10F 0.1F GND_IO GND_IO FERRITE BEAD PV GND_IO VDD_IO POWER 0.01F SUPPLY DECOUPLING GND_IO DD 1.8V 33F 10F 0.1F PGND PGND FERRITE BEAD VAA 3.3V 33F PGND 33F DGND PGND 2. THE I2C DEVICE ADDRESS IS CONFIGURABLE USING THE ALSB PIN: ALSB = 0, I2C DEVICE ADDRESS = 0xD4 ALSB = 1, I2C DEVICE ADDRESS = 0xD6 10F 0.1F AGND AGND FERRITE BEAD VDD 1.8V PVDD POWER SUPPLY DECOUPLING 0.01F NOTES 1. FOR OPTIMUM PERFORMANCE, EXTERNAL COMPONENTS CONNECTED TO THE COMP, RSET AND DAC OUTPUT PINS SHOULD BE LOCATED CLOSE TO, AND ON THE SAME SIDE OF THE PCB AS, THE ADV7390. AGND 10F 0.1F DGND DGND VAA POWER 1F SUPPLY AGND DECOUPLING 0.01F AGND VDD POWER SUPPLY DECOUPLING FOR EACH POWER PIN 0.01F DGND 3. THE RESISTOR CONNECTED TO THE RSET PIN SHOULD HAVE A 1% TOLERANCE. 4. THE RECOMMENDED MODE OF OPERATION FOR THE DACs IS FULLDRIVE (RSET = 510, RL = 37.5). PIXEL PORT INPUTS CONTROL INPUTS/OUTPUTS HSYNC VSYNC VAA VDD_IO P0 P1 P2 P3 P4 P5 P6 P7 PVDD VDD VDD VAA 2.2nF COMP RSET 510 ADV7390BCBZ AGND ALSB TIE EITHER LOW OR HIGH DAC FULL DRIVE OPTION (RECOMMENDED) CLOCK INPUT CLKIN OPTIONAL LPF DAC 1 I2C PORT VIDEO 75 SDA SCL DAC LOW DRIVE OPTION RESET RSET EXTERNAL LOOP FILTER 4.12k AGND 12nF ADA4411-3 EXT_LF 150nF 170 75 DAC LOOP FILTER COMPONENTS AGND PGND DGND DGND GND_IO SHOULD BE LOCATED CLOSE TO THE EXT_LF PIN AND ON THE SAME SIDE OF THE PCB AS THE ADV7390. AGND PGND DGND DGND GND_IO LPF VIDEO 300 AGND Figure 94. ADV7390BCBZ-A (WLCSP) Typical Applications Circuit Rev. J | Page 73 of 107 06234-148 PVDD ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet COPY GENERATION MANAGEMENT SYSTEM SD CGMS Subaddress 0x99 to Subaddress 0x9B The ADV7390/ADV7391/ADV7392/ADV7393 support a copy generation management system (CGMS) that conforms to the EIAJ CPR-1204 and ARIB TR-B15 standards. CGMS data is transmitted on Line 20 of odd fields and Line 283 of even fields. Subaddress 0x99, Bits[6:5] control whether CGMS data is output on odd or even fields or both. SD CGMS data can be transmitted only when the ADV7390/ ADV7391/ADV7392/ADV7393 are configured in NTSC mode. The CGMS data is 20 bits long. The CGMS data is preceded by a reference pulse of the same amplitude and duration as a CGMS bit (see Figure 95). When HD CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 720p CGMS data is applied to Line 24 of the luminance vertical blanking interval. When HD CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 1080i CGMS data is applied to Line 19 and Line 582 of the luminance vertical blanking interval. The HD CGMS data registers are at Subaddress 0x41, Subaddress 0x42, and Subaddress 0x43. The ADV7390/ADV7391/ADV7392/ADV7393 also support CGMS Type B packets in HD mode (720p and 1080i) in accordance with CEA-805-A. ED CGMS When HD CGMS Type B is enabled (Subaddress 0x5E, Bit 0 = 1), 720p CGMS data is applied to Line 23 of the luminance vertical blanking interval. Subaddress 0x41 to Subaddress 0x43; Subaddress 0x5E to Subaddress 0x6E 525p Mode When HD CGMS Type B is enabled (Subaddress 0x5E, Bit 0 = 1), 1080i CGMS data is applied to Line 18 and Line 581 of the luminance vertical blanking interval. The ADV7390/ADV7391/ADV7392/ADV7393 support a copy generation management system (CGMS) in 525p mode in accordance with EIAJ CPR-1204-1. The HD CGMS Type B data registers are at Subaddress 0x5E to Subaddress 0x6E. When ED CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 525p CGMS data is inserted on Line 41. The 525p CGMS data registers are at Subaddress 0x41, Subaddress 0x42, and Subaddress 0x43. If SD CGMS CRC (Subaddress 0x99, Bit 4) or ED/HD CGMS CRC (Subaddress 0x32, Bit 7) is enabled, the upper six CGMS data bits (C19 to C14) that comprise the 6-bit CRC check sequence are automatically calculated on the ADV7390/ ADV7391/ADV7392/ADV7393. This calculation is based on the lower 14 bits (C13 to C0) of the data in the CGMS data registers, and the result is output with the remaining 14 bits to form the complete 20 bits of the CGMS data. The calculation of the CRC sequence is based on the polynomial x6 + x + 1 with a preset value of 111111. The ADV7390/ADV7391/ADV7392/ADV7393 also support CGMS Type B packets in 525p mode in accordance with CEA805-A. When ED CGMS Type B is enabled (Subaddress 0x5E, Bit 0 = 1), 525p CGMS Type B data is inserted on Line 40. The 525p CGMS Type B data registers are at Subaddress 0x5E to Subaddress 0x6E. 625p Mode The ADV7390/ADV7391/ADV7392/ADV7393 support a copy generation management system (CGMS) in 625p mode in accordance with IEC 62375 (2004). When ED CGMS is enabled (Subaddress 0x32, Bit 6 = 1), 625p CGMS data is inserted on Line 43. The 625p CGMS data registers are at Subaddress 0x42 and Subaddress 0x43. HD CGMS Subaddress 0x41 to Subaddress 0x43; Subaddress 0x5E to Subaddress 0x6E The ADV7390/ADV7391/ADV7392/ADV7393 support a copy generation management system (CGMS) in HD mode (720p and 1080i) in accordance with EIAJ CPR-1204-2. CGMS CRC FUNCTIONALITY If SD CGMS CRC or ED/HD CGMS CRC is disabled, all 20 bits (C19 to C0) are output directly from the CGMS registers (CRC must be calculated by the user manually). If ED/HD CGMS Type B CRC (Subaddress 0x5E, Bit 1) is enabled, the upper six CGMS Type B data bits (P122 to P127) that comprise the 6-bit CRC check sequence are automatically calculated on the ADV7390/ADV7391/ADV7392/ADV7393. This calculation is based on the lower 128 bits (H0 to H5 and P0 to P121) of the data in the CGMS Type B data registers. The result is output with the remaining 128 bits to form the complete 134 bits of the CGMS Type B data. The calculation of the CRC sequence is based on the polynomial x6 + x + 1 with a preset value of 111111. If ED/HD CGMS Type B CRC is disabled, all 134 bits (H0 to H5 and P0 to P127) are output directly from the CGMS Type B registers (CRC must be calculated by the user manually). Rev. J | Page 74 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 +100 IRE CRC SEQUENCE REF +70 IRE C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 0 IRE -40 IRE 06234-093 49.1s 0.5s 11.2s 2.235s 20ns Figure 95. Standard Definition CGMS Waveform CRC SEQUENCE +700mV REF BIT 1 BIT 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT 20 70% 10% C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 0mV -300mV 21.2s 0.22s 22T 5.8s 0.15s 6T 06234-094 T = 1/(fH x 33) = 963ns fH = HORIZONTAL SCAN FREQUENCY T 30ns Figure 96. Enhanced Definition (525p) CGMS Waveform R = RUN-IN S = START CODE PEAK WHITE R 500mV 25mV S C0 C1 LSB C2 C3 C4 SYNC LEVEL C5 C6 C7 C8 C9 C10 C11 C12 C13 MSB 06234-095 13.7s 5.5s 0.125s Figure 97. Enhanced Definition (625p) CGMS Waveform CRC SEQUENCE +700mV REF BIT 1 BIT 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT 20 70% 10% C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 0mV 4T 3.128s 90ns 17.2s 160ns 22T T = 1/(fH x 1650/58) = 781.93ns fH = HORIZONTAL SCAN FREQUENCY 1H Figure 98. High Definition (720p) CGMS Waveform Rev. J | Page 75 of 107 06234-096 T 30ns -300mV ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet CRC SEQUENCE +700mV REF BIT 1 BIT 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BIT 20 70% 10% C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 0mV T 30ns 22.84s 210ns 22T T = 1/(fH x 2200/77) = 1.038s fH = HORIZONTAL SCAN FREQUENCY 1H 4T 4.15s 60ns 06234-097 -300mV Figure 99. High Definition (1080i) CGMS Waveform CRC SEQUENCE +700mV START BIT 1 BIT 2 BIT 134 P127 P126 P125 . P124 . P123 . P122 P4 P3 P2 P1 P0 H4 H5 H3 H2 H0 H1 70% 10% 0mV 06234-098 -300mV NOTES 1. PLEASE REFER TO THE CEA-805-A SPECIFICATION FOR TIMING INFORMATION. Figure 100. Enhanced Definition (525p) CGMS Type B Waveform CRC SEQUENCE +700mV START BIT 1 BIT 2 BIT 134 P127 P126 P124 . P125 . P123 . P122 P3 P4 P2 P1 P0 H5 H4 H3 H1 H2 H0 70% 10% 0mV NOTES 1. PLEASE REFER TO THE CEA-805-A SPECIFICATION FOR TIMING INFORMATION. Figure 101. High Definition (720p and 1080i) CGMS Type B Waveform Rev. J | Page 76 of 107 06234-099 -300mV Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 SD WIDE SCREEN SIGNALING sequence and a start code (see Figure 102). The latter portion of Line 23 (after 42.5 s from the falling edge of HSYNC) is available for the insertion of video. WSS data transmission on Line 23 can be enabled using Subaddress 0x99, Bit 7. It is possible to blank the WSS portion of Line 23 with Subaddress 0xA1, Bit 7. Subaddress 0x99, Subaddress 0x9A, Subaddress 0x9B The ADV7390/ADV7391/ADV7392/ADV7393 support wide screen signaling (WSS) con-forming to the ETSI 300 294 standard. WSS data is transmitted on Line 23. WSS data can be transmitted only when the device is configured in PAL mode. The WSS data is 14 bits long. The function of each of these bits is shown in Table 59. The WSS data is preceded by a run-in Table 59. Function of WSS Bits Bit Description Aspect Ratio, Format, Position 13 12 11 10 9 Bit Number 8 7 6 5 4 Mode 3 1 0 0 1 0 1 1 0 2 0 0 0 0 1 1 1 1 W8 W9 0 1 Color Encoding 0 1 Helper Signals 0 1 Reserved Teletext Subtitles 0 0 1 Open Subtitles 0 0 1 1 Surround Sound 0 1 0 1 0 1 Copyright 0 1 Copy Protection 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 Setting 4:3, full format, N/A 14:9, letterbox, center 14:9, letterbox, top 16:9, letterbox, center 16:9, letterbox, top >16:9, letterbox, center 14:9, full format, center 16:0, N/A, N/A Camera mode Film mode Normal PAL Motion Adaptive ColorPlus Not present Present N/A No Yes No Subtitles in active image area Subtitles out of active image area Reserved No Yes No copyright asserted or unknown Copyright asserted Copying not restricted Copying restricted 500mV RUN-IN SEQUENCE START CODE W0 W1 W2 W3 W4 W5 W6 W7 W10 W11 W12 W13 ACTIVE VIDEO 11.0s 06234-100 38.4s 42.5s Figure 102. WSS Waveform Diagram Rev. J | Page 77 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet SD CLOSED CAPTIONING The ADV7390/ADV7391/ADV7392/ADV7393 automatically generate all clock run-in signals and timing that support closed captioning on Line 21 and Line 284. All pixels inputs are ignored on Line 21 and Line 284 if closed captioning is enabled. Subaddress 0x91 to Subaddress 0x94 The ADV7390/ADV7391/ADV7392/ADV7393 support closed captioning conforming to the standard television synchronizing waveform for color trans-mission. When enabled, closed captioning is transmitted during the blanked active line time of Line 21 of the odd fields and Line 284 of the even fields. Closed captioning can be enabled using Subaddress 0x83, Bits[6:5]. The FCC Code of Federal Regulations (CFR) Title 47 Section 15.119 and EIA-608 describe the closed captioning information for Line 21 and Line 284. Closed captioning consists of a seven-cycle sinusoidal burst that is frequency- and phase-locked to the caption data. After the clock run-in signal, the blanking level is held for two data bits and is followed by a Logic 1 start bit. Sixteen bits of data follow the start bit. The data consists of two 8-bit bytes (seven data bits and one odd parity bit per byte). The data for these bytes is stored in SD closed captioning registers (Subaddress 0x93 to Subaddress 0x94). The ADV7390/ADV7391/ADV7392/ADV7393 also support the extended closed captioning operation, which is active during even fields and encoded on Line 284. The data for this operation is stored in SD closed captioning registers (Subaddress 0x91 to Subaddress 0x92). The ADV7390/ADV7391/ADV7392/ADV7393 use a single buffering method. This means that the closed captioning buffer is only 1-byte deep. Therefore, there is no frame delay in outputting the closed captioning data, unlike other 2-byte deep buffering systems. The data must be loaded one line before it is output on Line 21 and Line 284. A typical implementation of this method is to use VSYNC to interrupt a microprocessor, which in turn loads the new data (two bytes) in every field. If no new data is required for transmission, 0s must be inserted in both data registers; this is called nulling. It is also important to load control codes, all of which are double bytes, on Line 21. Otherwise, a TV does not recognize them. If there is a message such as "Hello World" that has an odd number of characters, it is important to add a blank character at the end to make sure that the end-of-caption, 2-byte control code lands in the same field. 12.91s 10.5 0.25s 7 CYCLES OF 0.5035MHz CLOCK RUN-IN TWO 7-BIT + PARITY ASCII CHARACTERS (DATA) P A R I T Y S T A D0 TO D6 R T 50 IRE D0 TO D6 BYTE 0 P A R I T Y BYTE 1 40 IRE 10.003s 33.764s 27.382s Figure 103. SD Closed Captioning Waveform, NTSC Rev. J | Page 78 of 107 06234-101 REFERENCE COLOR BURST (9 CYCLES) FREQUENCY = FSC = 3.579545MHz AMPLITUDE = 40 IRE Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 INTERNAL TEST PATTERN GENERATION SD TEST PATTERNS ED/HD TEST PATTERNS The ADV7390/ADV7391/ADV7392/ADV7393 are able to internally generate SD color bar and black bar test patterns. For this function, a 27 MHz clock signal must be applied to the CLKIN pin. The ADV7390/ADV7391/ADV7392/ADV7393 are able to internally generate ED/HD color bar, black bar, and hatch test patterns. For ED test patterns, a 27 MHz clock signal must be applied to the CLKIN pin. For HD test patterns, a 74.25 MHz clock signal must be applied to the CLKIN pin. The register settings in Table 60 are used to generate an SD NTSC 75% color bar test pattern. All other registers are set as normal/ default. Component YPrPb output is available on DAC 1 to DAC 3. On power-up, the subcarrier frequency registers default to the appropriate values for NTSC. Table 60. SD NTSC Color Bar Test Pattern Register Writes Subaddress 0x00 0x82 0x84 Setting 0x1C 0xC9 0x40 For component RGB output rather than YPrPb output, 0 should be written to Subaddress 0x02, Bit 5. To generate an SD NTSC black bar test pattern, the settings shown in Table 60 should be used with an additional write of 0x24 to Subaddress 0x02. For PAL output of either test pattern, the same settings are used except that Subaddress 0x80 is programmed to 0x11, and the subcarrier frequency (FSC) registers are programmed as shown in Table 61. Table 61. PAL FSC Register Writes Description FSC0 FSC1 FSC2 FSC3 Table 62. ED 525p Hatch Test Pattern Register Writes Subaddress 0x00 0x01 0x31 For CVBS and S-Video (Y/C) output, 0xCB instead of 0xC9 should be written to Subaddress 0x82. Subaddress 0x8C 0x8D 0x8E 0x8F The register settings in Table 62 are used to generate an ED 525p hatch test pattern. All other registers are set as normal/ default. Component YPrPb output is available on DAC 1 to DAC 3. For component RGB output rather than YPrPb output, 0 should be written to Subaddress 0x02, Bit 5. Setting 0x1C 0x10 0x05 To generate an ED 525p black bar test pattern, the settings shown in Table 62 should be used with an additional write of 0x24 to Subaddress 0x02. To generate an ED 525p flat field test pattern, the settings shown in Table 62 should be used, except that 0x0D should be written to Subaddress 0x31. The Y, Cr, and Cb levels for the hatch and flat field test patterns can be controlled using Subaddress 0x36, Subaddress 0x37, and Subaddress 0x38, respectively. For ED/HD standards other than 525p, the settings shown in Table 62 (and subsequent comments) are used, except that Subaddress 0x30, Bits[7:3] are updated as appropriate. Setting 0xCB 0x8A 0x09 0x2A Note that, when programming the FSC registers, the user must write the values in the sequence FSC0, FSC1, FSC2, FSC3. The full FSC value to be written is only accepted after the FSC3 write is complete. Rev. J | Page 79 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet SD TIMING Mode 0 (CCIR-656)--Slave Option (Subaddress 0x8A = X X X X X 0 0 0) The ADV7390/ADV7391/ADV7392/ADV7393 are controlled by the SAV (start of active video) and EAV (end of active video) time codes embedded in the pixel data. All timing information is transmitted using a 4-byte synchronization pattern. A synchronization pattern is sent immediately before and after each line during active picture and retrace. If the VSYNC and HSYNC pins are not used, they should be tied to VDD_IO when using this mode. ANALOG VIDEO EAV CODE C C 8 1 8 1 F 0 0 X C Y C Y C Y r Y b b 0 0 0 0 F 0 0 Y b r 0 F F A A A 0 F F B B B ANCILLARY DATA (HANC) 4 CLOCK 4 CLOCK 268 CLOCK NTSC/PAL M SYSTEM (525 LINES/60Hz) 4 CLOCK 4 CLOCK PAL SYSTEM (625 LINES/50Hz) 1440 CLOCK 1440 CLOCK 280 CLOCK 06234-102 INPUT PIXELS SAV CODE C F 0 0 X 8 1 8 1 Y Y r F 0 0 Y 0 0 0 0 START OF ACTIVE VIDEO LINE END OF ACTIVE VIDEO LINE Figure 104. SD Timing Mode 0, Slave Option Mode 0 (CCIR-656)--Master Option (Subaddress 0x8A = X X X X X 0 0 1) The ADV7390/ADV7391/ADV7392/ADV7393 generate H and F signals required for the SAV and EAV time codes in the CCIR-656 standard. The H bit is output on HSYNC and the F bit is output on VSYNC. DISPLAY DISPLAY VERTICAL BLANK 522 523 524 525 1 2 3 4 5 6 7 8 10 9 11 20 21 22 H EVEN FIELD F ODD FIELD DISPLAY DISPLAY VERTICAL BLANK 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 283 284 285 F ODD FIELD 06234-103 H EVEN FIELD Figure 105. SD Timing Mode 0, Master Option, NTSC Rev. J | Page 80 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 DISPLAY DISPLAY VERTICAL BLANK 622 623 624 625 1 2 4 3 5 6 21 7 22 23 H ODD FIELD EVEN FIELD F DISPLAY DISPLAY VERTICAL BLANK 309 310 311 312 314 313 315 316 318 317 319 335 334 320 336 ODD FIELD F 06234-104 H EVEN FIELD Figure 106. SD Timing Mode 0, Master Option, PAL ANALOG VIDEO 06234-105 H F Figure 107. SD Timing Mode 0, Master Option, Data Transitions Mode 1--Slave Option (Subaddress 0x8A = X X X X X 0 1 0) In this mode, the ADV7390/ADV7391/ADV7392/ADV7393 accept horizontal synchronization and odd/even field signals. When HSYNC is low, a transition of the field input indicates a new frame, that is, vertical retrace. HSYNC and FIELD are input on the HSYNC and VSYNC pins, respectively. DISPLAY DISPLAY 522 523 VERTICAL BLANK 524 525 1 2 3 4 5 6 7 8 9 10 11 20 21 22 HSYNC FIELD EVEN FIELD ODD FIELD DISPLAY 260 261 DISPLAY VERTICAL BLANK 262 263 264 265 266 267 268 269 270 271 272 273 274 283 284 285 FIELD ODD FIELD 06234-106 HSYNC EVEN FIELD Figure 108. SD Timing Mode 1, Slave Option, NTSC Rev. J | Page 81 of 107 ADV7390/ADV7391/ADV7392/ADV7393 DISPLAY DISPLAY 622 623 Data Sheet VERTICAL BLANK 624 625 1 2 4 3 5 6 7 23 22 21 HSYNC FIELD EVEN FIELD ODD FIELD DISPLAY DISPLAY 309 310 VERTICAL BLANK 311 312 313 314 315 316 317 318 319 320 334 335 336 ODD FIELD FIELD 06234-107 HSYNC EVEN FIELD Figure 109. SD Timing Mode 1, Slave Option, PAL Mode 1--Master Option (Subaddress 0x8A = X X X X X 0 1 1) In this mode, the ADV7390/ADV7391/ADV7392/ADV7393 can generate horizontal synchronization and odd/even field signals. When HSYNC is low, a transition of the field input indicates a new frame, that is, vertical retrace. The ADV7390/ADV7391/ADV7392/ADV7393 automatically blank all normally blank lines as required by the CCIR-624 standard. Pixel data is latched on the rising clock edge following the timing signal transitions. HSYNC and FIELD are output on the HSYNC and VSYNC pins, respectively. HSYNC FIELD Cb Y PAL = 132 x CLOCK/2 NTSC = 122 x CLOCK/2 Cr Y 06234-108 PIXEL DATA Figure 110. SD Timing Mode 1, Odd/Even Field Transitions (Master/Slave) Mode 2-- Slave Option (Subaddress 0x8A = X X X X X 1 0 0) In this mode, the ADV7390/ADV7391/ADV7392/ADV7393 accept horizontal and vertical synchronization signals. A coincident low transition of both HSYNC and VSYNC inputs indicates the start of an odd field. A VSYNC low transition when HSYNC is high indicates the start of an even field. The ADV7390/ADV7391/ADV7392/ADV7393 automatically blank all normally blank lines as required by the CCIR-624 standard. HSYNC and VSYNC are input on the HSYNC and VSYNC pins, respectively. Rev. J | Page 82 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 DISPLAY 522 DISPLAY VERTICAL BLANK 523 524 525 1 4 3 2 5 7 6 8 10 9 20 11 21 22 HSYNC VSYNC ODD FIELD EVEN FIELD DISPLAY DISPLAY VERTICAL BLANK 260 261 262 263 264 265 266 267 268 269 270 271 272 273 283 274 284 285 VSYNC 06234-109 HSYNC EVEN FIELD ODD FIELD Figure 111. SD Timing Mode 2, Slave Option, NTSC DISPLAY 622 623 DISPLAY VERTICAL BLANK 624 625 1 2 3 4 5 6 7 21 22 23 HSYNC VSYNC EVEN FIELD ODD FIELD DISPLAY 309 310 DISPLAY VERTICAL BLANK 311 312 313 314 315 316 317 318 319 320 334 335 336 ODD FIELD VSYNC 06234-110 HSYNC EVEN FIELD Figure 112. SD Timing Mode 2, Slave Option, PAL Mode 2--Master Option (Subaddress 0x8A = X X X X X 1 0 1) In this mode, the ADV7390/ADV7391/ADV7392/ADV7393 can generate horizontal and vertical synchronization signals. A coincident low transition of both HSYNC and VSYNC inputs indicates the start of an odd field. A VSYNC low transition when HSYNC is high indicates the start of an even field. The ADV7390/ADV7391/ADV7392/ADV7393 automatically blank all normally blank lines as required by the CCIR-624 standard. HSYNC and VSYNC are output on the HSYNC and VSYNC pins, respectively. HSYNC VSYNC Cb PAL = 132 x CLOCK/2 NTSC = 122 x CLOCK/2 Figure 113. SD Timing Mode 2, Even-to-Odd Field Transition (Master/Slave) Rev. J | Page 83 of 107 Y Cr Y 06234-111 PIXEL DATA ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet HSYNC VSYNC PAL = 864 x CLOCK/2 NTSC = 858 x CLOCK/2 PIXEL DATA Cb Y Cr Cb 06234-112 Y PAL = 132 x CLOCK/2 NTSC = 122 x CLOCK/2 Figure 114. SD Timing Mode 2, Odd-to-Even Field Transition (Master/Slave) Mode 3--Master/Slave Option (Subaddress 0x8A = X X X X X 1 1 0 or X X X X X 1 1 1) In this mode, the ADV7390/ADV7391/ADV7392/ADV7393 accept or generates horizontal synchronization and odd/even field signals. When HSYNC is high, a transition of the field input indicates a new frame, that is, vertical retrace. The ADV7390/ADV7391/ADV7392/ ADV7393 automatically blank all normally blank lines as required by the CCIR-624 standard. HSYNC and VSYNC are output in master mode and input in slave mode on the HSYNC and VSYNC pins, respectively. DISPLAY DISPLAY 522 523 VERTICAL BLANK 524 525 1 2 4 3 5 6 8 7 9 10 20 11 21 22 HSYNC FIELD EVEN FIELD ODD FIELD DISPLAY 260 DISPLAY VERTICAL BLANK 261 262 263 264 265 266 267 268 269 270 271 272 273 283 274 285 284 FIELD ODD FIELD 06234-113 HSYNC EVEN FIELD Figure 115. SD Timing Mode 3, NTSC DISPLAY 622 623 DISPLAY VERTICAL BLANK 624 625 1 2 3 4 5 6 7 21 22 23 HSYNC FIELD EVEN FIELD ODD FIELD DISPLAY DISPLAY 309 310 VERTICAL BLANK 311 312 313 314 315 316 317 318 319 320 334 335 336 FIELD EVEN FIELD 06234-114 HSYNC ODD FIELD Figure 116. SD Timing Mode 3, PAL Rev. J | Page 84 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 HD TIMING DISPLAY FIELD 1 VERTICAL BLANKING INTERVAL 1124 1125 1 2 3 4 5 6 7 8 20 21 22 560 VSYNC HSYNC DISPLAY VERTICAL BLANKING INTERVAL FIELD 2 561 562 563 564 565 566 567 568 569 570 583 584 585 1123 06234-115 VSYNC HSYNC Figure 117. 1080i HSYNC and VSYNC Input Timing Rev. J | Page 85 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet VIDEO OUTPUT LEVELS SD YPrPb OUTPUT LEVELS--SMPTE/EBU N10 700mV BLACK BLUE RED MAGENTA GREEN CYAN YELLOW WHITE BLACK BLUE RED MAGENTA GREEN CYAN YELLOW WHITE Pattern: 100% Color Bars 700mV 300mV 06234-119 06234-116 300mV 700mV BLACK BLUE RED MAGENTA GREEN CYAN YELLOW WHITE BLACK Figure 121. Y Levels--PAL BLUE RED MAGENTA GREEN CYAN YELLOW WHITE Figure 118. Y Levels--NTSC 06234-120 06234-117 700mV BLACK BLUE RED MAGENTA GREEN CYAN WHITE 700mV YELLOW Figure 122. Pr Levels--PAL BLACK BLUE RED MAGENTA GREEN CYAN YELLOW WHITE Figure 119. Pr Levels--NTSC 06234-121 06234-118 700mV Figure 120. Pb Levels--NTSC Figure 123. Pb Levels--PAL Rev. J | Page 86 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 ED/HD YPrPb OUTPUT LEVELS INPUT CODE INPUT CODE EIA-770.2, STANDARD FOR Y OUTPUT VOLTAGE EIA-770.3, STANDARD FOR Y OUTPUT VOLTAGE 940 940 700mV 700mV 64 300mV 64 300mV EIA-770.3, STANDARD FOR Pr/Pb OUTPUT VOLTAGE 960 EIA-770.2, STANDARD FOR Pr/Pb OUTPUT VOLTAGE 960 600mV 512 700mV 06234-124 700mV 512 06234-122 64 64 Figure 126. EIA-770.3 Standard Output Signals (1080i/720p) Figure 124. EIA-770.2 Standard Output Signals (525p/625p) INPUT CODE INPUT CODE EIA-770.1, STANDARD FOR Y Y-OUTPUT LEVELS FOR FULL INPUT SELECTION OUTPUT VOLTAGE 1023 OUTPUT VOLTAGE 782mV 940 700mV 714mV 64 300mV 64 286mV INPUT CODE Pr/Pb-OUTPUT LEVELS FOR FULL INPUT SELECTION OUTPUT VOLTAGE 1023 EIA-770.1, STANDARD FOR Pr/Pb OUTPUT VOLTAGE 960 700mV 700mV 64 64 06234-123 300mV Figure 125. EIA-770.1 Standard Output Signals (525p/625p) Rev. J | Page 87 of 107 Figure 127. Output Levels for Full Input Selection 06234-125 512 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet SD/ED/HD RGB OUTPUT LEVELS Pattern: 100%/75% Color Bars R R 700mV/525mV 700mV/525mV 300mV 300mV G G 700mV/525mV 700mV/525mV 300mV 300mV B B 06234-126 300mV 300mV Figure 128. SD/ED RGB Output Levels--RGB Sync Disabled 06234-128 700mV/525mV 700mV/525mV Figure 130. HD RGB Output Levels--RGB Sync Disabled R R 700mV/525mV 600mV 700mV/525mV 300mV 300mV 0mV 0mV G G 700mV/525mV 600mV 700mV/525mV 300mV 300mV 0mV 0mV B B 700mV/525mV 600mV 700mV/525mV 06234-127 0mV Figure 129. SD/ED RGB Output Levels--RGB Sync Enabled Rev. J | Page 88 of 107 06234-129 300mV 300mV 0mV Figure 131. HD RGB Output Levels--RGB Sync Enabled Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 SD OUTPUT PLOTS VOLTS VOLTS IRE:FLT 0.6 100 0.4 0.5 50 0.2 0 0 0 -0.2 10 L608 30 40 50 60 MICROSECONDS PRECISION MODE OFF APL = 44.5% SYNCHRONOUS SYNC =A 525 LINE NTSC FRAMES SELECTED 1, 2 SLOW CLAMP TO 0.00V AT 6.72s 0 20 10 20 30 40 50 60 MICROSECONDS NOISE REDUCTION: 0.00dB PRECISION MODE OFF APL = 39.1% SYNCHRONOUS SOUND-IN-SYNC OFF 625 LINE NTSC NO FILTERING FRAMES SELECTED 1, 2, 3, 4 SLOW CLAMP TO 0.00 AT 6.72s Figure 132. NTSC Color Bars (75%) 06234-133 0 F1 L76 06234-130 -50 Figure 135. PAL Color Bars (75%) VOLTS VOLTS IRE:FLT 0.6 0.5 0.4 50 0.2 0 00 0 L575 F2 L238 10 0 20 30 40 50 60 MICROSECONDS NOISE REDUCTION: 15.05dB APL = 44.3% PRECISION MODE OFF 525 LINE NTSC NO FILTERING SYNCHRONOUS SYNC = SOURCE SLOW CLAMP TO 0.00V AT 6.72s FRAMES SELECTED 1, 2 10 20 30 40 50 60 70 MICROSECONDS NO BUNCH SIGNAL APL NEEDS SYNC SOURCE. PRECISION MODE OFF 625 LINE PAL NO FILTERING SYNCHRONOUS SOUND-IN-SYNC OFF SLOW CLAMP TO 0.00 AT 6.72s FRAMES SELECTED 1 06234-134 -0.2 06234-131 0 Figure 136. PAL Luma Figure 133. NTSC Luma VOLTS VOLTS IRE:FLT 0.4 50 0.5 0.2 0 0 0 -0.2 -50 -0.5 -0.4 L575 10 20 30 40 50 60 MICROSECONDS NOISE REDUCTION: 15.05dB PRECISION MODE OFF APL NEEDS SYNC SOURCE. SYNCHRONOUS SYNC = B 525 LINE NTSC NO FILTERING FRAMES SELECTED 1, 2 SLOW CLAMP TO 0.00 AT 6.72s 06234-132 0 0 30 40 50 60 MICROSECONDS APL NEEDS SYNC SOURCE. NO BUNCH SIGNAL 625 LINE PAL NO FILTERING PRECISION MODE OFF SLOW CLAMP TO 0.00 AT 6.72s SYNCHRONOUS SOUND-IN-SYNC OFF FRAMES SELECTED 1 Figure 134. NTSC Chroma Rev. J | Page 89 of 107 10 20 Figure 137. PAL Chroma 06234-135 F1 L76 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet VIDEO STANDARDS 0HDATUM SMPTE 274M ANALOG WAVEFORM DIGITAL HORIZONTAL BLANKING *1 272T 4T ANCILLARY DATA (OPTIONAL) OR BLANKING CODE EAV CODE 1920T DIGITAL ACTIVE LINE F 0 0 F C V b Y C r F 0 0 H* 0 0 F 0 0 V H* F F INPUT PIXELS 4T SAV CODE 4 CLOCK SAMPLE NUMBER 2112 C Y r 4 CLOCK 0 2199 2116 2156 44 188 192 2111 06234-136 FVH* = FVH AND PARITY BITS SAV/EAV: LINE 1-562: F = 0 SAV/EAV: LINE 563-1125: F = 1 SAV/EAV: LINE 1-20; 561-583; 1124-1125: V = 1 SAV/EAV: LINE 21-560; 584-1123: V = 0 FOR A FRAME RATE OF 30Hz: 40 SAMPLES FOR A FRAME RATE OF 25Hz: 480 SAMPLES Figure 138. EAV/SAV Input Data Timing Diagram (SMPTE 274M) SMPTE 293M ANALOG WAVEFORM ANCILLARY DATA (OPTIONAL) EAV CODE F F 0 0 V F 0 0 H* INPUT PIXELS F 0 0 F V F 0 0 H* C Y r Y C C b Y r 4 CLOCK 4 CLOCK 723 736 0HDATUM 719 SAMPLE NUMBER DIGITAL ACTIVE LINE SAV CODE 857 0 853 799 719 DIGITAL HORIZONTAL BLANKING 06234-137 FVH* = FVH AND PARITY BITS SAV: LINE 43-525 = 200H SAV: LINE 1-42 = 2AC EAV: LINE 43-525 = 274H EAV: LINE 1-42 = 2D8 Figure 139. EAV/SAV Input Data Timing Diagram (SMPTE 293M) 522 523 524 ACTIVE VIDEO VERTICAL BLANK 525 1 2 5 6 7 8 9 12 13 Figure 140. SMPTE 293M (525p) Rev. J | Page 90 of 107 14 15 16 42 43 44 06234-138 ACTIVE VIDEO ADV7390/ADV7391/ADV7392/ADV7393 ACTIVE VIDEO 622 623 ACTIVE VIDEO VERTICAL BLANK 624 625 1 2 5 4 6 7 8 9 10 12 11 13 43 44 45 06234-139 Data Sheet Figure 141. ITU-R BT.1358 (625p) DISPLAY 747 748 749 4 3 2 1 750 7 6 5 8 25 26 27 744 745 06234-140 VERTICAL BLANKING INTERVAL Figure 142. SMPTE 296M (720p) DISPLAY VERTICAL BLANKING INTERVAL FIELD 1 1124 1125 1 2 3 4 5 6 7 8 20 21 560 22 DISPLAY VERTICAL BLANKING INTERVAL 561 562 563 564 565 566 567 568 569 Figure 143. SMPTE 274M (1080i) Rev. J | Page 91 of 107 570 583 584 585 1123 06234-141 FIELD 2 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet CONFIGURATION SCRIPTS The scripts listed in the following pages can be used to configure the ADV7390/ADV7391/ADV7392/ADV7393 for basic operation. Certain features are enabled by default. If required for a specific application, additional features can be enabled. Table 63 lists the scripts available for SD modes of operation. Similarly, Table 98 and Table 115 list the scripts available for ED and HD modes of operation, respectively. For all scripts, only the necessary register writes are included. All other registers are assumed to have their default values. The WLCSP package supports only scripts in Table 65, Table 79, Table 82, and Table 96. In those scripts, Subaddress 0x00 must be set to 0x10. STANDARD DEFINITION Table 63. SD Configuration Scripts Input Format 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) 525i (NTSC) Input Data Width 1 8-bit SDR 8-bit SDR 8-bit SDR 8-bit SDR 8-bit SDR 10-bit SDR 10-bit SDR 10-bit SDR 10-bit SDR 10-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR Synchronization Format EAV/SAV EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC HSYNC/VSYNC EAV/SAV HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC Input Color Space YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb RGB RGB RGB Output Color Space YPrPb CVBS/Y-C (S-Video) YPrPb RGB RGB YPrPb YPrPb CVBS/Y-C (S-Video) RGB RGB YPrPb RGB YPrPb CVBS/Y-C (S-Video) RGB Table Number Table 64 Table 65 Table 66 Table 67 Table 68 Table 69 Table 70 Table 71 Table 72 Table 73 Table 74 Table 75 Table 76 Table 77 Table 78 NTSC Sq. Pixel NTSC Sq. Pixel 8-bit SDR 16-bit SDR YCrCb RGB CVBS/Y-C (S-Video) CVBS/Y-C (S-Video) Table 79 Table 80 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) 625i (PAL) PAL Sq. Pixel PAL Sq. Pixel 8-bit SDR 8-bit SDR 8-bit SDR 8-bit SDR 8-bit SDR 10-bBit SDR 10-bit SDR 10-bit SDR 10-bit SDR 10-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR 8-bit SDR 16-bit SDR EAV/SAV HSYNC/VSYNC EAV/SAV EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC HSYNC/VSYNC EAV/SAV HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC HSYNC/VSYNC EAV/SAV HSYNC/VSYNC YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb RGB RGB RGB YCrCb RGB YPrPb CVBS/Y-C (S-Video) YPrPb RGB RGB YPrPb YPrPb CVBS/Y-C (S-Video) RGB RGB YPrPb RGB YPrPb CVBS/Y-C (S-Video) RGB CVBS/Y-C (S-Video) CVBS/Y-C (S-Video) Table 81 Table 82 Table 83 Table 84 Table 85 Table 86 Table 87 Table 88 Table 89 Table 90 Table 91 Table 92 Table 93 Table 94 Table 95 Table 96 Table 97 1 SDR = single data rate. Rev. J | Page 92 of 107 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 64. 8-Bit 525i YCrCb In (EAV/SAV), YPrPb Out Table 68. 8-Bit 525i YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x10 0x82 0xC9 0x82 0xC9 0x8A 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Table 65. 8-Bit 525i YCrCb In (EAV/SAV), CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x10 0x00 0x10 0x82 0xCB Description Software reset All DACs enabled. PLL enabled (16x). WLCSP required. SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 69. 10-Bit 525i YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xC9 0x88 0x10 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 10-bit input enabled. Table 66. 8-Bit 525i YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xC9 0x8A 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 67. 8-Bit 525i YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x10 0x82 0xC9 Table 70. 10-Bit 525i YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xC9 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Rev. J | Page 93 of 107 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 10-bit input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 71. 10-Bit 525i YCrCb In, CVBS/Y-C Out Table 74. 16-Bit 525i YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xCB 0x82 0xC9 0x88 0x8A 0x10 0x0C 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 10-bit input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 72. 10-Bit 525i YCrCb In (EAV/SAV), RGB Out Table 75. 16-Bit 525i YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x10 0x80 0x10 0x82 0xC9 0x82 0xC9 0x88 0x10 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 10-bit input enabled. Description Software reset All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 73. 10-Bit 525i YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x10 0x82 0xC9 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. 10-bit input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 76. 16-Bit 525i RGB In, YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xC9 0x87 0x88 0x8A 0x80 0x10 0x0C Rev. J | Page 94 of 107 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 77. 16-Bit 525i RGB In, CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xCB 0x87 0x88 0x8A 0x80 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 78. 16-Bit 525i RGB In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x10 0x82 0xC9 0x87 0x88 0x8A 0x80 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 79. 8-Bit NTSC Square Pixel YCrCb In (EAV/SAV), CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x10 0x00 0x10 0x82 0xDB 0x8C 0x8D 0x8E 0x8F 0x55 0x55 0x55 0x25 Description Software reset All DACs enabled. PLL enabled (16x). WLCSP required. SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Square pixel mode enabled. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in NTSC square pixel mode (24.5454 MHz input clock). Table 80. 16-Bit NTSC Square Pixel RGB In, CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x10 0x82 0xDB 0x87 0x88 0x8A 0x80 0x10 0x0C 0x8C 0x8D 0x8E 0x8F 0x55 0x55 0x55 0x25 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. NTSC standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Pedestal enabled. Square pixel mode enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in NTSC square pixel mode (24.5454 MHz input clock). Table 81. 8-Bit 625i YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xC1 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Table 82. 8-Bit 625i YCrCb In (EAV/SAV), CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x10 0x00 0x11 0x82 0xC3 0x8C 0x8D 0x8E 0x8F 0xCB 0x8A 0x09 0x2A Rev. J | Page 95 of 107 Description Software reset. All DACs enabled. PLL enabled (16x). WLCSP required. SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in PAL mode (27 MHz input clock). ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 83. 8-Bit 625i YCrCb In, YPrPb Out Table 87. 10-Bit 625i YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xC1 0x82 0xC1 0x8A 0x0C 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. 10-bit input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 84. 8-Bit 625i YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x11 0x82 0xC1 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Table 85. 8-Bit 625i YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x11 0x82 0xC1 0x8A 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 86. 10-Bit 625i YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xC1 0x88 0x10 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. 10-bit input enabled. Table 88. 10-Bit 625i YCrCb In, CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xC3 0x88 0x8A 0x10 0x0C 0x8C 0x8D 0x8E 0x8F 0xCB 0x8A 0x09 0x2A Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel Data Valid. CVBS/Y-C (S-Video) Out. SSAF PrPb filter enabled. Active video edge control enabled. 10-bit input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in PAL mode (27 MHz input clock). Table 89. 10-Bit 625i YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x11 0x82 0xC1 0x88 0x10 Rev. J | Page 96 of 107 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. 10-bit input enabled. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 90. 10-Bit 625i YCrCb In, RGB Out Table 93. 16-Bit 625i RGB In, YPrPb Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x80 0x11 0x82 0xC1 0x82 0xC1 0x87 0x88 0x8A 0x80 0x10 0x0C 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. 10-bit input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 94. 16-Bit 625i RGB In, CVBS/Y-C Out Table 91. 16-Bit 625i YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xC1 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. YPrPb out. SSAF PrPb filter enabled. Active video edge control enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Table 92. 16-Bit 625i YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x11 0x82 0xC1 0x88 0x8A 0x10 0x0C Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xC3 0x87 0x88 0x8A 0x80 0x10 0x0C 0x8C 0x8D 0x8E 0x8F 0xCB 0x8A 0x09 0x2A Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in PAL mode (27 MHz input clock). Table 95. 16-Bit 625i RGB In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x00 0x10 0x80 0x11 0x82 0xC1 0x87 0x88 0x8A 0x80 0x10 0x0C Rev. J | Page 97 of 107 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. RGB output enabled. RGB output sync enabled. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. RGB out. SSAF PrPb filter enabled. Active video edge control enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. ADV7390/ADV7391/ADV7392/ADV7393 Table 97. 16-Bit PAL Square Pixel RGB In, CVBS/Y-C Out Table 96. 8-Bit PAL Square Pixel YCrCb In (EAV/SAV), CVBS/Y-C Out Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x10 0x00 0x11 0x82 0xD3 0x8C 0x8D 0x8E 0x8F 0x0C 0x8C 0x79 0x26 Data Sheet Description Software reset. All DACs enabled. PLL enabled (16x). WLCSP required. SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Square pixel mode enabled. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in PAL square pixel mode (29.5 MHz input clock). Subaddress 0x17 0x00 0x01 0x80 Setting 0x02 0x1C 0x00 0x11 0x82 0xD3 0x87 0x88 0x8A 0x80 0x10 0x0C 0x8C 0x8D 0x8E 0x8F 0x0C 0x8C 0x79 0x26 Rev. J | Page 98 of 107 Description Software reset. All DACs enabled. PLL enabled (16x). SD input mode. PAL standard. SSAF luma filter enabled. 1.3 MHz chroma filter enabled. Pixel data valid. CVBS/Y-C (S-Video) out. SSAF PrPb filter enabled. Active video edge control enabled. Square pixel mode enabled. RGB input enabled. 16-bit RGB input enabled. Timing Mode 2 (slave). HSYNC/VSYNC synchronization. Subcarrier frequency register values for CVBS and/or S-Video (Y-C) output in PAL square pixel mode (29.5 MHz input clock). Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 ENHANCED DEFINITION Table 98. ED Configuration Scripts Input Format 525p 525p 525p 525p 525p 525p 525p 525p Input Data Width 8-bit DDR 8-bit DDR 10-bit DDR 10-bit DDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR Synchronization Format EAV/SAV EAV/SAV EAV/SAV EAV/SAV EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC Input Color Space YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb Output Color Space YPrPb RGB YPrPb RGB YPrPb YPrPb RGB RGB Table Number Table 107 Table 109 Table 108 Table 110 Table 99 Table 100 Table 101 Table 102 625p 625p 625p 625p 625p 625p 625p 625p 8-bit DDR 8-bit DDR 10-bit DDR 10-bit DDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR EAV/SAV EAV/SAV EAV/SAV EAV/SAV EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YPrPb RGB YPrPb RGB YPrPb YPrPb RGB RGB Table 111 Table 113 Table 112 Table 114 Table 103 Table 104 Table 105 Table 106 Table 99. 16-Bit 525p YCrCb In (EAV/SAV), YPrPb Out Table 102. 16-Bit 525p YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x04 Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x31 0x01 0x30 0x00 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. 525p at 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Table 100. 16-Bit 525p YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x00 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. 525p at 59.94 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels. Pixel data valid. Table 101. 16-Bit 525p YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x30 0x04 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. RGB output enabled. RGB output sync enabled. 525p at 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. RGB output enabled. RGB output sync enabled. 525p at 59.94 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels. Pixel data valid. Table 103. 16-Bit 625p YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x1C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. 625p at 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Table 104. 16-Bit 625p YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x18 0x31 0x01 Rev. J | Page 99 of 107 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. 625p at 50 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels. Pixel data valid. ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 105. 16-Bit 625p YCrCb In (EAV/SAV), RGB Out Table 109. 8-Bit 525p YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x30 0x1C 0x30 0x04 0x31 0x01 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. RGB output enabled. RGB output sync enabled. 625p at 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 525p at 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Table 106. 16-Bit 625p YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x30 0x18 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-SDR input mode. RGB output enabled. RGB output sync enabled. 625p at 50 Hz. HSYNC/VSYNC synchronization. EIA-770.2 output levels. Pixel data valid. Table 107. 8-Bit 525p YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x30 0x04 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. 525p at 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Table 110. 10-Bit 525p YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x30 0x04 0x31 0x33 0x01 0x6C Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 525p at 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. 10-bit input enabled. Table 111. 8-Bit 625p YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x30 0x1C Table 108. 10-Bit 525p YCrCb In (EAV/SAV), YPrPb Out 0x31 0x01 Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 Table 112. 10-Bit 625p YCrCb In (EAV/SAV), YPrPb Out 0x30 0x04 0x31 0x33 0x01 0x6C Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. 525p at 59.94 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. 10-bit input enabled. Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x30 0x1C 0x31 0x33 0x01 0x6C Rev. J | Page 100 of 107 Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. 625p at 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. 625p at 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. 10-bit input enabled. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 113. 8-Bit 625p YCrCb In (EAV/SAV), RGB Out Table 114. 10-Bit 625p YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x02 0x10 0x30 0x1C 0x30 0x1C 0x31 0x01 0x31 0x33 0x01 0x6C Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 625p at 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. Description Software reset. All DACs enabled. PLL enabled (8x). ED-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 625p at 50 Hz. EAV/SAV synchronization. EIA-770.2 output levels. Pixel data valid. 10-bit input enabled. HIGH DEFINITION Table 115. HD Configuration Scripts Input Format 720p 720p 720p 720p 720p 720p 720p 720p Input Data Width 8-bit DDR 8-bit DDR 10-bit DDR 10-bit DDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR Synchronization Format EAV/SAV EAV/SAV EAV/SAV EAV/SAV EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC Input Color Space YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb Output Color Space YPrPb RGB YPrPb RGB YPrPb YPrPb RGB RGB Table Number Table 124 Table 126 Table 125 Table 127 Table 116 Table 117 Table 118 Table 119 1080i 1080i 1080i 1080i 1080i 1080i 1080i 1080i 8-bit DDR 8-bit DDR 10-bit DDR 10-bit DDR 16-bit SDR 16-bit SDR 16-bit SDR 16-bit SDR EAV/SAV EAV/SAV EAV/SAV EAV/SAV EAV/SAV HSYNC/VSYNC EAV/SAV HSYNC/VSYNC YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YCrCb YPrPb RGB YPrPb RGB YPrPb YPrPb RGB RGB Table 128 Table 130 Table 129 Table 131 Table 120 Table 121 Table 122 Table 123 Rev. J | Page 101 of 107 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet Table 116. 16-Bit 720p YCrCb In (EAV/SAV), YPrPb Out Table 121. 16-Bit 1080i YCrCb In, YPrPb Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x2C Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x18 0x31 0x01 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. 720p at 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. 1080i at 30 Hz/29.97 Hz. HSYNC/VSYNC synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 117. 16-Bit 720p YCrCb In, YPrPb Out Table 122. 16-Bit 1080i YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x28 Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x31 0x01 0x30 0x6C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. 720p at 60 Hz/59.94 Hz. HSYNC/VSYNC synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. RGB output enabled. RGB output sync enabled. 1080i at 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 118. 16-Bit 720p YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x30 0x2C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. RGB output enabled. RGB output sync enabled. 720p at 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 123. 16-Bit 1080i YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x30 0x18 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. RGB output enabled. RGB output sync enabled. 1080i at 30 Hz/29.97 Hz. HSYNC/VSYNC synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 119. 16-Bit 720p YCrCb In, RGB Out Subaddress 0x17 0x00 0x01 0x02 Setting 0x02 0x1C 0x10 0x10 0x30 0x28 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. RGB output enabled. RGB output sync enabled. 720p at 60 Hz/59.94 Hz. HSYNC/VSYNC synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 124. 8-Bit 720p YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x30 0x2C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. 720p at 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 125. 10-Bit 720p YCrCb In (EAV/SAV), YPrPb Out Table 120. 16-Bit 1080i YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 0x30 Setting 0x02 0x1C 0x10 0x6C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-SDR input mode. 1080i at 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x30 0x2C 0x31 0x33 0x01 0x6C Rev. J | Page 102 of 107 Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. 720p at 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. 10-bit input enabled. Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 Table 126. 8-Bit 720p YCrCb In (EAV/SAV), RGB Out Table 129. 10-Bit 1080i YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x30 0x6C 0x30 0x2C 0x31 0x33 0x01 0x6C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 720p at 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 130. 8-Bit 1080i YCrCb In (EAV/SAV), RGB Out Table 127. 10-Bit 720p YCrCb In (EAV/SAV), RGB Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x30 0x2C 0x31 0x33 0x01 0x6C Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. 1080i at 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. 10-bit input enabled. Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 720p at 60 Hz/59.94 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. 10-bit input enabled. Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x30 0x6C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 1080i at 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Table 131. 10-Bit 1080i YCrCb In (EAV/SAV), RGB Out Table 128. 8-Bit 1080i YCrCb In (EAV/SAV), YPrPb Out Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x30 0x6C 0x31 0x01 Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. 1080i at 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. Subaddress 0x17 0x00 0x01 Setting 0x02 0x1C 0x20 0x02 0x10 0x30 0x6C 0x31 0x33 0x01 0x6C Rev. J | Page 103 of 107 Description Software reset. All DACs enabled. PLL enabled (4x). HD-DDR input mode. Luma data clocked on falling edge of CLKIN. RGB output enabled. RGB output sync enabled. 1080i @ 30 Hz/29.97 Hz. EAV/SAV synchronization. EIA-770.3 output levels. Pixel data valid. 4x oversampling. 10-bit input enabled. ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 EVALUATION BOARD These two boards allow the user to perform a complete evaluation of the part, although it is also possible to order only the back-end board. Note that these two boards must be ordered separately. To accommodate evaluation of the ADV7390/ADV7391/ ADV7392/ADV7393, Analog Devices provides a two-board solution. The ADV7390/ADV7391/ADV7392/ADV7393 evaluation platform front-end board contains an Analog Devices decoder (ADV7403) and an FPGA. The back-end board (where the actual ADV7390/ADV7391/ADV7392/ ADV7393 are attached) is connected to the front-end board through a connector. For more information about the evaluation boards, see the evaluation board documentation available on the Analog Devices product web page. FRONT-END EVALUATION BOARD YPrPb DECODER FPGA YC USB CVBS ENCODER RGB YPrPb Figure 144. ADV7390/ADV7391/ADV7392/ADV7393 Front-End and Back-End Evaluation Boards Rev. J | Page 104 of 107 YC 06234-145 ADV7403 BACK-END EVALUATION BOARD ADV7403 INTERFACE RGB ADV739x INTERFACE EXPANSION PORT CVBS Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 OUTLINE DIMENSIONS 5.10 5.00 SQ 4.90 0.60 MAX 0.60 MAX 25 32 24 4.75 BSC SQ PIN 1 INDICATOR 1 0.50 BSC 3.25 3.10 SQ 2.95 EXPOSED PAD 17 PKG-001050 SEATING PLANE 0.20 MIN BOTTOM VIEW 3.50 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF 0.30 0.25 0.18 9 11-10-2017-B 12 MAX 1.00 0.85 0.80 0.80 MAX 0.65 TYP 8 16 0.50 0.40 0.30 TOP VIEW PIN 1 INDICATOR COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2 Figure 145. 32-Lead Lead Frame Chip Scale Package [LFCSP] 5 mm x 5 mm Body and 0.85 mm Package Height (CP-32-2) Dimensions shown in millimeters 0.30 0.25 0.18 PIN 1 INDIC ATOR AREA OPTIONS (SEE DETAIL A) 32 25 1 24 0.50 BSC 3.45 3.30 SQ 3.15 EXPOSED PAD 8 17 TOP VIEW 0.80 0.75 0.70 PKG-003530 SEATING PLANE END VIEW 0.50 0.40 0.30 9 16 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF BOTTOM VIEW 3.50 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WHHD. Figure 146. 32-Lead Lead Frame Chip Scale Package [LFCSP] 5 mm x 5 mm Body and 0.75 mm Package Height (CP-32-13) Dimensions shown in millimeters Rev. J | Page 105 of 107 0.20 MIN 10-19-2017-B PIN 1 INDICATOR DETAIL A (JEDEC 95) 5.10 5.00 SQ 4.90 ADV7390/ADV7391/ADV7392/ADV7393 Data Sheet 2.565 2.525 2.485 5 3 4 2 1 A BALL A1 IDENTIFIER B 3.045 3.005 2.965 2.50 REF C D E F 0.50 BALL PITCH TOP VIEW BOTTOM VIEW (BALL SIDE UP) (BALL SIDE DOWN) 0.660 0.600 0.540 0.390 0.360 0.330 SIDE VIEW 2.00 REF COPLANARITY 0.05 0.360 0.320 0.280 0.270 0.240 0.210 10-31-2012-C SEATING PLANE Figure 147. 30-Ball Wafer Level Chip Scale Package [WLCSP] (CB-30-3) Dimensions shown in millimeters DETAIL A (JEDEC 95) 0.30 0.23 0.18 31 40 30 0.50 BSC 4.25 4.10 SQ 3.95 EXPOSED PAD 21 TOP VIEW 0.80 0.75 0.70 PKG-004354 SEATING PLANE SIDE VIEW 0.45 0.40 0.35 10 11 20 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF BOTTOM VIEW 0.20 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WJJD-5. Figure 148. 40-Lead Lead Frame Chip Scale Package [LFCSP] 6 mm x 6 mm Body and 0.75 mm Package Height (CP-40-9) Dimensions shown in millimeters Rev. J | Page 106 of 107 PIN 1 INDIC ATOR AREA OPTIONS (SEE DETAIL A) 1 10-23-2017-B PIN 1 INDICATOR 6.10 6.00 SQ 5.90 Data Sheet ADV7390/ADV7391/ADV7392/ADV7393 ORDERING GUIDE Model1, 2 ADV7390BCPZ ADV7390BCPZ-REEL ADV7390WBCPZ ADV7390WBCPZ-RL ADV7390BCBZ-A-RL ADV7391BCPZ ADV7391BCPZ-REEL ADV7391WBCPZ ADV7391WBCPZ-RL ADV7392BCPZ ADV7392BCPZ-REEL ADV7392BCPZ-3REEL ADV7392WBCPZ ADV7392WBCPZ-REEL ADV7393BCPZ ADV7393BCPZ-REEL ADV7393WBCPZ ADV7393WBCPZ-REEL EVAL-ADV739xFEZ EVAL-ADV7390EBZ EVAL-ADV7391EBZ EVAL-ADV7392EBZ EVAL-ADV7393EBZ 1 2 3 Temperature Range -40C to +85C -40C to +85C -40C to +105C -40C to +105C -40C to +85C -40C to +85C -40C to +85C -40C to +105C -40C to +105C -40C to +85C -40C to +85C -40C to +85C -40C to +105C -40C to +105C -40C to +85C -40C to +85C -40C to +105C -40C to +105C Macrovision3 Antitaping Yes Yes Yes Yes Yes No No No No Yes Yes Yes Yes Yes No No No No Not available Yes No Yes No Package Description 32-Lead Lead Frame Chip Scale Package [LFCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 30-Ball Wafer Level Chip Scale Package [WLCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 32-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] 40-Lead Lead Frame Chip Scale Package [LFCSP] ADV739x Evaluation Platform Front-End Board ADV7390 Evaluation Board ADV7391 Evaluation Board ADV7392 Evaluation Board ADV7393 Evaluation Board Package Option CP-32-2 CP-32-2 CP-32-13 CP-32-13 CB-30-3 CP-32-2 CP-32-2 CP-32-13 CP-32-13 CP-40-9 CP-40-9 CP-40-9 CP-40-9 CP-40-9 CP-40-9 CP-40-9 CP-40-9 CP-40-9 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. Macrovision-enabled ICs require the buyer to be an approved licensee (authorized buyer) of ICs that are able to output Macrovision Rev 7.1.L1-compliant video. AUTOMOTIVE PRODUCTS The ADV7390W, ADV7391W, ADV7392W, and ADV7393W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). (c)2006-2018 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06234-0-8/18(J) Rev. J | Page 107 of 107