TPI Tripolar protection for ISDN interfaces Features Bidirectional triple crowbar protection Peak pulse current: IPP = 30 A , 10/1000 s Breakdown voltage: - TPI80N: 80 V - TPI120N: 120 V Complies with following standards Available in SO-8 package Low dynamic breakover voltage: - TPI8011N: 120 V - TPI12011N: 170 V CCITT K17-K20 - 10/700 s, 1.5 kV - 5/310 s, 38 A VDE 0433 - 10/700 s, 2 kV - 5/310 s, 50 A VDE 0878 - 1.2/50 s, 1.5 kV - 1/20 s, 40 A IEC 61000-4-2 level 4 - 0.5/700 s, 1.5 kV - 0.2/310 s, 38 A SO-8 Benefits Low capacitance from lines to ground, allowing high speed transmission without signal attenuation Good capacitance balance between lines to ensure longitudinal balance Fixed breakdown voltage in both common and differential modes The same surge current capability in both common and differential modes A particular attention has been given to the internal wire bonding. The "4-point" configuration ensures a reliable protection, eliminating overvoltages introduced by the parasitic inductances of the wiring (LdI/dt), especially for very fast transient overvoltages Description Dedicated devices for ISDN interface and high speed data telecom line protection. Equivalent to a triple TrisilTM with low capacitance. Figure 1. Functional diagram Tip 1 8 Tip GND 2 7 GND GND 3 6 GND Ring 4 5 Ring TM: Trisil is a trademark of STMicroelectronics November 2007 Rev 5 1/9 www.st.com 9 Characteristics 1 TPI Characteristics Table 1. Absolute ratings (Tamb = 25 C) Symbol Parameter Value Unit Peak pulse current (see note (1)) 10/1000 s 5/310 s 2/10 s 30 40 90 A ITSM Non repetitive surge peak on-state current (F = 50 Hz) tp = 10 ms t = 1s 8 3.5 A Tstg Tj Storage temperature range Maximum junction temperature - 55 to 150 150 C 260 C Value Unit 170 C/W IPP TL Maximum lead temperature for soldering during 10 s. 1. See Figure 3. Table 2. Thermal resistances Symbol Rth(j-a) Table 3. Parameter Junction to ambient Electrical characteristics (Tamb = 25 C) Symbol Parameter VRM Stand-off voltage VBR Breakdown voltage VBO Breakover voltage IRM Leakage current IPP Peak pulse current IBO Breakover current IH Holding current VF Forward voltage drop C Capacitance IRM @ VRM Order code max. A VBR @ IR min. V VBO VBO dyn. IBO IH max. note (1) typ. note (2) max. note (1) min. note(3) V mA V V mA mA TPI8011N 10 70 80 1 110 120 800 150 TPI12011N 10 105 120 1 160 170 800 150 1. See the reference test circuit 1 (Figure 5.) 2. Surge test according to CCITT 1.5 kV, 10/700 s between Tip or Ring and ground 3. See functional holding current test circuit 2 (Figure 6.) Figure 2. 2/9 TPI Characteristics Table 4. Capacitance characteristics CONFIGURATION CA (pF) max. CB (pF) max. CA - CB (pF) max. VA = -1 V VB = -56 V 45 15 30 VA = -56 V VB = -1 V 15 45 30 LINE A LINE A CA TPIxx CB LINE B Figure 3. LINE B Pulse waveform (10/1000 s) Figure 4. Surge peak current versus overload duration ITSM(A) % I PP 10 F=50Hz Tj initial=25C 9 10 0 8 7 6 5 50 4 3 2 0 tr tp t 1 0 1E-2 t(s) 1E-1 1E+0 1E+1 1E+2 1E+3 3/9 Characteristics TPI Figure 5. Reference test circuit 1 tp = 20 ms Auto Transformer 220 V / 2 A R1 140 Static relay R2 240 220 V K VOUT D.U.T. IBO, IH measure VBO measure Transformer 220 V / 800 V 2A TEST PROCEDURE Pulse test duration (tp = 20 ms): for Bidirectional devices = Switch K is closed for Unidirectional devices = Switch K is open VOUT selection: Device with VBO < 200 V VOUT = 250 VRMS, R1 = 140 Device with VBO > 200 V VOUT = 480 VRMS, R2 = 240 Figure 6. Functional holding current (IH) test circuit 2 R D.U.T. - VP VBAT = - 48 V Surge generator This is a GO-NOGO test which allows to confirm the holding current (IH) level in a functional test circuit. TEST PROCEDURE 1/ Adjust the current level at the IH value by short circuiting the AK of the D.U.T. 2/ Fire the D.U.T. with a surge current IPP 10 A, 10/1000 s. 3/ The D.U.T. will come back off-state within 50 ms maximum. 4/9 TPI 2 Application information Application information Figure 7. Application circuit - U interface protection R or PTC A TPIxx GND R or PTC B Figure 8. Application circuit - S interface protection A R or PTC TPIxx GND R or PTC B A R or PTC TPIxx GND R or PTC B This component uses an intemal structure resulting in symetrical characteristics with a good balanced behaviour. Its topology ensures the same breakdown voltage level for positive and negative surges in differential and common mode. 5/9 Ordering information scheme Figure 9. TPI Connections 1. Tip 1 IN OUT 2 8 GND 3 3 2. 7 GND Ring Tip 4 6 IN OUT 5 Ring Connect pins 2, 3, 6 and 7 to ground in order to guarantee a good surge current capability for long duration disturbances. To take advantage of the "4-point" structure of the TPIxxxN, the Tip and Ring lines have to cross the device. In this case, the device will eliminate the overvoltages generated by the parasitic inductances of the wiring (LdI/dt), especially for very fast transients. Ordering information scheme Figure 10. Ordering information scheme TPI 80 1 1 N RL Bidirectional Tripolar Protection Breakdown voltage 80 = 80 V Version Package 1 = SO-8 Revision Packing mode RL = Tape and reel Blank = Tube 6/9 TPI 4 Package information Package information Epoxy meets UL94, V0 In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Table 5. SO-8 dimensions Dimensions Ref. Seating Plane C A2 C ppp C L1 D 8 5 0.069 0.1 0.25 0.004 0.010 A2 1.25 0.049 b 0.28 0.48 0.011 0.019 C 0.17 0.23 0.007 0.009 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 E1 1 1.75 A1 L k Inches Min. Typ. Max. Min. Typ. Max. A A A1 e b h x 45 Millimeters e E 4 1.27 0.050 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 L1 k 1.04 0 ppp 0.041 8 0.10 0 8 0.004 Figure 11. SO-8 footprint, dimensions in mm (inches) 6.8 (0.268) 0.6 (0.024) 4.2 (0.165) 1.27 (0.050) 7/9 Ordering Information 5 TPI Ordering Information Table 6. Ordering information Order code Marking TPI8011N TP80N TPI8011NRL (1) Package Weight TP80N SO-8 Base qty Delivery mode 100 Tube 2500 Tape and reel 0.08 g TPI12011N TP120N 100 Tube TPI12011NRL (1) TP120N 2500 Tape and reel 1. Prefered device 6 Revision history Table 7. 8/9 Document revision history Date Revision Changes August-2001 3A 02-Aug-2004 4 VBO dyn. (page 2) and capacitances (page 3) values update. 07-Nov-2007 5 Reformatted to current standards. Updated Package information. Last update. TPI Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 9/9