CANNON
KPT / KPSE / KPTC Connectors
In Accordance with VG95328
www.ittcannon.com2
Our connector portfolio remains the most extensive in the industry, offering a reliable and cost effec-
tive range of interconnect solutions with the brands of Cannon, VEAM and BIW Connector Systems.
Continuous investment in technology and research & development have enabled ITT to provide new,
innovative products and solutions to markets including:
ITT
Corporation
ITT is a diversified leading manufacturer of highly engineered critical
components and customized technology solutions for the energy, trans-
portation and industrial markets. Building on its heritage of innovation,
ITT partners with its customers to deliver enduring solutions to the key
industries that underpin our modern way of life. Founded in 1920, ITT
is headquartered in White Plains, N. Y., with employees in more than 35
countries and sales in a total of approximately 125 countries. The com-
pany generated 2012 revenues of $ 2.2 billion. For more information,
visit www.itt.com.
www.ittcannon.com 3
Our connector portfolio
remains the most extensive
in the industry, offering a reliable and
cost effective range of interconnect
solutions
Automotive
Oil & Gas
Commercial & Military Aerospace
Computer, Telecom &
Consumer Electronics
Transportation
lndustrial / lnstrumentation
Defense Vehicles
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
4
Introduction to KPSE /KPT /KPTC
ITT Cannon's miniature circular connector series KPT, KPSE and KPTC
conform to meet the performance specification to MIL-C-26482 with a
positive three point bayonet coupling, five-keyway polarization and high
insert arrangement contact density.
Purpose
• General purpose solder connectors (KPT)
– Our solution for small / prototype quantities
using solder type contacts
• High versatility general purpose versions using
crimp or solder contacts (KPTC)
– Our commercial version for higher volume production
with option for solder contacts
• High performance crimp connectors (KPSE)
– Our solution for volume production optimized for fast
assembly featuring “clip-in” contact & insulator design
• Military approved versions according to VG95328
or MIL-C-26482
The broad product range provides the most complete family
of connectors conforming to VG95328 and MIL-C-26482
specications.
Highlights
• All connectors conforming to the above mentioned standards
are fully intermateable and accept a wide range of interchange-
able accessories.
• Design modications can be achieved easily and a lower
cost using Cannons KPSE / KPT or KPTC versions
• VG95328 versions are based on MIL-C-26482 but comply
to ECC directives and offer additional shielded versions
• KPTC is based on MIL-C-26482 but offers a greater versatility
in contacts, backshells and plating options
• “Blue Generation” RoHS compliant, 500 hours salt spray and
conductive plating is offered next to the standard Nickel,
Zinc Cobalt or Cadmium platings.
Contact us for detail or your request
for a customized solution.
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
5
Product overview
KPT KPSE KPTC
Material and Finishes
Shell Aluminum alloy Aluminum alloy Aluminum alloy
Various RoHS compliant plating options are available like Zinc cobalt, Zinc Nickel and Nickel plus none compliant Cadmium
Insulator Polychloroprene Polychloroprene Polychloroprene
Grommet and seal Polychloroprene Polychloroprene Polychloroprene
Contacts Copper alloy, gold and tin plated Copper alloy, gold and tin plated Copper alloy, hard gold and tin plated
Mechanical Data
Shell styles
00 – Wall mounting receptacle 07 – Jam nut receptacle
01 – Cable connecting plug 08 – Plug with 90° termination assemblies
02 – Box mounting receptacle B – Thru-bulkhead receptacle (KPT only)
06 – Straight plug
Shell size 8 through 24
Polarization / Coupling Five keyways / 3-point bayonet
Service classes
A – General duty
E – Grommet seal
F – Grommet seal with strain relief
PG – PG gland adapters
ME – metric gland adapters
Environmental sealing According to VG95319 Part 2, Test No. 5.9.2 | For styles A to E and Z1, Z2 and Z3 and gaskets style A only,
test pressure 0,2 bar overpressure, test duration 48 h, test temperature 25 ±3°C, connector shall be free of moisture
Operating temperature –55 / +125°C
Durability 500 mating cycles
Vibration 200 m/s² at 10 to 2000 Hz
Electrical Data
Number of contacts 2 through 61 3 through 61 2 through 61
Wire size AWG 16 through 24 12 through 24 0,4 – 2,0 mm²
Contact termination Solder Crimp Crimp, solder
KPT /KPSE /KPTC
Contact rating Size Rated current A Test current A Millivolt drop mV
20
16
7,5
13,0
7,5
13,0
Less than 55
Less than 50
Insulation resistance ~ 5000 MΩ
Exceptions Test voltage Service class Vrms VDC
Service rating between
the central contact and
the housing of the
coaxial contact
Seal Level 1 1500 2100
2 2300 3200
21336 m / 70 000 ft. 1 375 535
2 550 770
Operating voltage (with scoop proof connectors operating voltages acc. to MIL-C-26482 and VG95328 are permitted)
Service class VG95328 MIL-C-26482
1 140 VDC/100 VAC 850 VDC/600 VAC
2 165 VDC/115 VAC 1400 VDC/1000 VAC
Operating voltage When the connectors in this catalogue are used for voltages
greater than 50 Volts and have touchable conductive shell parts
they must be used in accordance with the safety
regulations DIN VDE Part 140; IEC 60364-4-41. This regulation
basically dictates that the power source should be turned off
before any mating and unmating of the connector. This regula-
tion does not provide protection against electrical shock when
mating and unmating the connectors in the live condition.
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
6
Product overview ................................................. 5
How to use this catalogue .................................... 7
Part number creation ........................................... 8
Ordering reference ...............................................10
Contact arrangements ..........................................12
Alternate insert positions ......................................15
Wall mounting receptacles ...................................16
Cable connecting plugs ........................................17
Box mounting receptacles ....................................18
Thru-bulkhead receptacles ....................................18
Straight plugs ......................................................19
Jam nut receptacles ..............................................21
Right angle plugs .................................................22
Special versions
Connectors with grounding continuity..................23
Receptacles with straight solder pins ....................26
Accessories and tooling
Panel cutouts .......................................................27
Protective caps .....................................................28
Dummy receptacle ...............................................30
Cross reference lists ............................................. 31
Tools and accessories ..........................................32
KPSE contact and sealing principle .......................33
Product safety information ...................................34
Table of contents
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
7
Select your product using either the “part number creation”
or “ordering reference” option
Use the detail pages to better understand the available
options and choose the best solution for your needs
Add accessories and tooling as required on the related
pages
Use the contact information on the back cover to contact
us for further questions or to get advise on where you can
purchase our products
1
2
3
4
How to use
This catalog is split in several sections that help you to
• get a general overview of all product lines (product overview)
• create a product part number step by step
(part number creation OR ordering reference)
• get all required detail information (dimensions, product details)
• get all required support products (accessories, tooling)
The fastest way to find your product of choice is to follow these steps
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
8
Part number creation plug
Follow these steps to design your connector part number.
Design your part number as per above steps
KPSE / KPT
Examples
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Shell style Class / Backshell Contact arrangement Contact gender Insulation rotation Mod code (max. 3 codes)
Solder Industrial KPT6 E 20 – 41 P – DZ
Crimp Industrial KPSE6 E 14 – 12 S – W – F42 – A240 – F0
KPTC
Examples
STEP 1 STEP 2 STEP 3 STEP 4 STEP 6 STEP 5 STEP 6
Shell style Class / Backshell Contact arrangement Contact gender Plating Insulation rotation Mod code (max. 3 codes)
Solder Industrial KPTC6 E 20 – 41 P C – MA
Crimp Industrial KPTC6 PG 14 – 12 S – D W – P13,5 – MB
STEP 1 Select shell style (plug)
Shell Style Plug Shell Style Plug Shell Style Plug
Plug straight Solder
KPT06
KPTC6
Crimp
KPSE06
Plug straight
shielded
Solder
KPT6-DZ
KPTC6-DZ
Crimp
KPSE6-DZ
Plug 90° Solder
KPT08
KPTC8
Crimp
KPSE08
STEP 2 Choose backshell
Class A
General
duty with
thread
Class F
Grommet seal
with strain relief
Class E
add mod. code DN
Environmental,
grommet seal,
heat shrink boot
adapter
Class PG; ME
KPTC only
Environmental
Class E
add Mod. code DZ
Environmental, grommet seal,
shielded heat shrink boot adapter
Class F, 90°
Grommet seal
with thread
and cable clamp
Class A, 90°
General duty
with thread
Class E, 90°
Grommet seal
with thread
STEP 3 Choose layout see page 12 –14 for layouts
STEP 4 Choose gender P=pin S=socket
STEP 5 Choose rotation see page 15 for rotation (omit for normal position)
STEP 6 Choose modication* see page 11 for modications (omit if no modication is required)
* If a modication is used the initial ‚0‘ in the shell style description is omitted e.g. KPT01 is changed to KPT1. KPTC series does never use the initial ‚0‘ e.g. KPTC6
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
9
Part number creation receptacle
Design your part number as per above steps
Follow these steps to design your connector part number.
KPSE / KPT
Examples
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Shell style Class / Backshell Contact arrangement Contact gender Insulation rotation Mod code (max. 3 codes)
Solder Industrial KPT02 E 20 – 41 P
Crimp Industrial KPSE1 E 14 – 12 S – W – F42 – A240 – F0
KPTC
Examples
STEP 1 STEP 2 STEP 3 STEP 4 STEP 6 STEP 5 STEP 6
Shell style Class / Backshell Contact arrangement Contact gender Plating Insulation rotation Mod code (max. 3 codes)
Solder Industrial KPTC2 E 20 – 41 P C – MA
Crimp Industrial KPTC0 PG 14 – 12 S – D W – P13,5 – MB
STEP 1 Select shell style (receptacle)
Wall Mount Cable connecting Jam Nut*Box Mount*Thru-Bulkhead
Solder
KPT00
KPTC0
Crimp
KPSE00
KPTC0
Solder
KPT01
KPTC1
Crimp
KPSE01
Solder
KPT07
KPTC7
Crimp
KPSE07
KPTC7
Solder
KPT02
KPTC2
Crimp
KPSE02
KPTC2
KPTB
(contacts pre-installed)
STEP 2 Choose backshell
Class A
General
duty with
thread
Class F
Grommet seal
with strain relief
Class E
Environmental,
grommet seal,
no clamp
Class E
add Mod. code DN
Environmental,
grommet seal,
heat shrink boot
adapter
Class PG or ME
Environmental,
KPTC only
Class E
add Mod. code DZ
Environmental,
grommet seal
shielded heat
shrink boot
adapter
STEP 3 Choose layout see page 12 –14 for layouts
STEP 4 Choose gender P=pin S=socket
STEP 5 Choose rotation see page 15 for rotation (omit for normal position)
STEP 6 Choose modication** see page 11 for modications (omit if no modication is required)
* Shell style 02 (box mount) and 07A (jam nut) doesn‘t accept a backshell
** If a modication is used the initial ‚0‘ in the shell style description is omitted e.g. KPT01 is changed to KPT1. KPTC series does never use the initial ‚0‘ e.g. KPTC6
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
10
Ordering reference
Series
KPSE – Cannon prex crimp, contacts supplied
KPT – Cannon prex solder, contacts installed
KPTC – Cannon prex commercial version, contacts to be ordered separately
Shell type
Cannon designation omit 0 in case of a mod code and KPTC
00 – wall mounting receptacle see page 16
01 – cable connecting plug see page 17
02 – box mounting receptacle (class E only), thru-bulkhead recep. see page 18
06 – straight plug see page 19/20
07 – jam nut receptacle see page 21
08 – 90° angle plug see page 22
Class
A – general duty with thread
E – grommet seal, environmental, no clamp
E – grommet seal, in combination with modication DN or DZ
F – grommet seal with strain relief
PG – endbell for PG glands
ME – endbell for metric glands
Shell size
8 – 24
Contact arrangement see page 12–14
Contact type
P – pin
S – socket
Alternate insert position
W, X, Y and Z (omit for normal position) see page 15
Modication see page 11
KPT / KPSE / KPTC KP.. 22 – 36E P W *02
* If a modication is used the initial ‚0‘ in the shell style description is omitted e.g. KPT01 is changed to KPT1. KPTC series does never use the initial ‚0‘ e.g. KPTC6
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
11
Specication
Shell type see page 31
A – wall mounting receptacle with straight endbell
B – wall mounting receptacle with cable clamp
C – box mounting receptacle
D – jam nut receptacle
E – jam nut receptacle with cable clamp
J – straight plug with adapter DN
K – straight plug with cable clamp
M – straight plug, version DZ
R – wall mounting receptacle, version DZ
S – jam nut receptacle with adapter DN
T – jam nut receptacle, version DZ
Shell size 8, 10, 12, 14, 16, 18, 20, 22 and 24
Contact arrangements see page 12 –14
Contact type P – pin S – socket
Alternate insert position see page 15
VG95328 18 – 1A S N
Multiple codes can be used in order of listing below KPSE KPT
Endbell
DN – heat shrink boot adapter, grommet seal DN DN
DZ – shielded, heat shrink boot adapter, grommet seal DZ DZ
F42 – without endbell, grommet and ferrule F42 F42
Plating (Cadmium with olive drab chromate plating is standard; Alternative platings below)
A232 – Zinc Cobalt, black plating (RoHS compliant) A232 A232
A240 – Zinc Nickel plating (RoHS compliant) (not for code DZ) A240 A240
A233 – Zinc Cobalt, green plating A233 A233
A34 – Nickel plating (RoHS compliant) A34 A34
Contact
F0 – connector without contacts F0 F0
EX – PCB solder pin 0,76x7mm (style 02 and 07 only) – EX
EW – PCB solder pin 0,6x7mm (style 02 and 07 only) – EW
Multiple codes can be used in order of listing below KPTC
Plating
Nickel plating (RoHS compliant) C
Zinc Cobalt black plating (RoHS compliant) R
Zinc Cobalt green plating (RoHS compliant) F
Zinc Nickel plating (RoHS compliant) (not for code DZ) H
Cadmium with olive drab chromate D
Endbell
DN – heat shrink boot adapter, grommet seal DN
DZ – shielded, heat shrink boot adapter, grommet seal DZ
F42 – without endbell, grommet and ferrule F42
Endbell for PG glands (KPTC and KPT)
PG09 - thread for shell size 10 P9
PG11 – thread for shell size 12 P11
PG13,5 – thread for shell size14 P13,5
PG16 – thread for shell size 16 P16
PG21 – thread for shell size 18, 20, 22 P21
PG29 – thread for shell size 24 P29
Endbell for metric glands (KPTC and KPT)
M12 – thread for shell size 10 M12
M16 – thread for shell size 12 M16
M20 – thread for shell size 14 M20
M25 – thread for shell size 16, 18, 20 M25
M32 – thread for shell size 22, 24 M32
Contact
Connector supplied with solder pot contacts installed MA
Connector supplied with crimp contacts MB
KPSE/KPT-Modification codes
Military approved version
KPTC-Modification codes
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
12
CONTACT ARRANGEMENTS
No. of contacts Contact arrangements Service rating Insulator position
Contact size
AWG
W X Y Z
28-2  
20
1 58 122 – –
38-3  
20
1 60 210 – –
38-3A  
20
1 60 – – –
38-33  
20
1 90 – – –
48-4  
20
1 45 – – –
610-6  
20
1 90 – – –
710-7  
20
1 90 – – –
610-98  
20
1 90 180 240 270
312-3  
16
2 – – 180 –
812-8  
20
1 90 112 203 292
10 12-10  
20
1 60 155 270 295
14 12-14  
20
1 60 155 270 295
514-5  
16
2 40 92 184 273
12 14-12  
20 (8)
16 (4)
1 43 90 – –
Legend KPT KPSE  authorized per MIL-C-26482  authorized per VG95328
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
13
CONTACT ARRANGEMENTS
No. of contacts Contact arrangements Service rating Insulator position
Contact size
AWG
W X Y Z
15 14-15  
20 (14)
16 (1)
1 17 110 155 234
18 14-18  
20
1 15 90 180 270
19 14-19  
20
1 30 165 315 –
514-22  
12 (4)
20 (1)
1 ––––
414A4  
Coax RG 188 U
(not for receptacle
shell style 02)
1 ––––
816-8  
16
2 54 152 180 331
23 16-23  
20 (22)
16 (1)
1 158 270 – –
26 16-26  
20
1 60 – 275 338
11 18-11  
16
2 62 119 241 340
32 18-32  
20
2 85 138 222 265
Legend KPT KPSE  authorized per MIL-C-26482  authorized per VG95328
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
14
CONTACT ARRANGEMENTS
No. of contacts Contact arrangements Service rating Insulator position
Contact size
AWG
W X Y Z
520A6  
12
Note: contacts are 1 grounding
pin and 4 standard size 12 pins
2 90 180 270 –
16 20-16  
16
2 238 316 333 347
24 20-24  
20
1 70 145 215 290
39 20-39  
20 (37)
16 (2)
1 63 114 252 333
41 20-41  
20
1 45 126 225 –
21 22-21  
16
2 16 135 175 349
36 22-36  
20
1 72 144 216 288
41 22-41  
20 (27)
16 (14)
1
2
39 135 264 –
55 22-55  
20
1 30 142 226 314
61 24-61  
20
1 90 180 270 324
Legend KPT KPSE  authorized per MIL-C-26482  authorized per VG95328
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
15
ALTERNATE INSERT POSITION
The diagram indicates alternate insert
positions.
The six positions N, V, W, Y, Z differ in
degree of rotation for various sizes and
arrangements. For the exact degree of
rotation, for the list of contact arrange-
ments and for alternate positions available,
refer to the table at the right.
Shell size No. of contacts Contact arrangements Degree of Rotation
V W X Y Z
82 8-2 – 58 122 – –
3 8-3 – 60 210 – –
3 8-3A – 60 – – –
3 8-33 – 90 – – –
4 8-4 – 45 – – –
10 6 10-6 – 90 – – –
7 10-7 – 90 – – –
6 10-98 – 90 180 240 270
12 3 12-3 – – – 180 –
8 12-8 – 90 112 203 292
10 12-10 – 60 155 270 295
14 12-14 – 60 155 270 295
14 4 14A4 –––––
5 14-5 – 40 92 184 273
12 14-12 – 43 90 – –
15 14-15 – 17 110 155 234
18 14-18 – 15 90 180 270
19 14-19 – 30 165 315 –
5 14-22 –––––
16 8 16-8 – 54 52 180 331
23 16-23 – 158 270 – –
26 16-26 – 60 – 275 338
18 11 18-11 – 62 119 241 340
32 18-32 – 85 138 222 265
20 520A6* – 90 180 270 –
16 20-16 – 238 318 333 347
24 20-24 – 70 145 215 290
39 20-39 – 63 114 252 333
41 20-41 – 45 126 225 –
22 21 22-21 – 16 135 175 349
36 22-36 – 72 144 216 288
41 22-41 – 39 135 264 –
55 22-55 – 30 142 226 314
24 61 24-61 – 90 180 270 324
* This contact arrangement features ve contacts size 12. Four standard contacts and one is a rst-to-mate contact.
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
16
WALL MOUNTING RECEPTACLES KPT00 / KPSE00 / KPTC0
Shell size Ø A Q K M R S Ø T
+0,03 – 0,13 Thread Type 2A ±0,1 ±0,15 ±0,15 max. ±0,15
8 12,00 7/16-28UNEF 1,9 11,6 15,1 21,0 3,05
10 15,00 9/16-24UNEF 1,9 11,6 18,3 24,2 3,05
12 19,05 11/16-24UNEF 1,9 11,6 20,6 26,6 3,05
14 22,23 13/16-20UNEF 1,9 11,6 23,0 29,0 3,05
16 25,40 15/16-20UNEF 1,9 11,6 24,6 31,3 3,05
18 28,58 1-1/16-18UNEF 1,9 11,6 27,0 33,7 3,05
20 31,75 1-3/16-18UNEF 2,2 14,25 29,4 36,9 3,05
22 34,93 1-5/16-18UNEF 2,2 14,25 31,8 40,1 3,05
24 38,10 1-7/16-18UNEF 2,2 15,1 34,9 43,3 3,75
Backshell options
Type A Type F Type E
Shell size Ø DAL AVTHD Ø GFHFLFØ BEL E
min. max. Thread Type 2A min. max. max. max. max.
8 8,5 38,0 1/2-28UNEF 2,9 19,3 56,0 14,2 32,5
10 11,8 38,0 5/8-24UNEF 4,5 20,8 56,0 17,2 32,5
12 15,0 38,0 3/4-20UNEF 7,7 24,4 56,0 20,4 32,5
14 17,9 38,0 7/8-20UNEF 9,3 27,2 56,0 23,4 32,5
16 21,1 38,0 1-20UNEF 12,4 28,7 56,0 26,6 32,5
18 24,1 38,0 1-3/16-18UNEF 15,6 35,3 56,0 29,6 32,5
20 26,5 43,1 1-3/16-18UNEF 15,6 35,3 61,0 32,8 34,5
22 30,4 43,1 1-7/16-18UNEF 18,8 39,9 61,0 36,0 34,5
24 32,8 43,1 1-7/16-18UNEF 20,1 43,2 61,0 39,2 34,5
Mod. DN
Shell size Ø D2 L1 L2
–0,5 max. ±0,5
8 15,6 35,0 12,2
10 18,4 35,0 12,2
12 23,7 35,0 12,2
14 24,5 35,0 12,2
16 29,8 37,0 14,5
18 32,0 37,0 14,5
20 36,1 42,0 15,8
22 38,5 42,0 15,8
24 41,6 42,0 14,9
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
17
CABLE CONNECTING PLUGS KPT01 / KPSE01 / KPTC1
Shell size Ø A K M QTHD S Ø Y
+0,03 - 0,13 ±0,1 ±0,15 Thread Type 2A max. max.
8 12,00 1,9 11,6 7/16-28UNEF 20,6 23,8
10 15,00 1,9 11,6 9/16-24UNEF 23,8 26,9
12 19,05 1,9 11,6 11/16-24UNEF 26,15 29,3
14 22,23 1,9 11,6 13/16-20UNEF 28,5 31,7
16 25,40 1,9 11,6 15/16-20UNEF 30,7 34,1
18 28,58 1,9 11,6 1-1/16-18UNEF 33,3 36,5
20 31,75 2,2 14,25 1-3/16-18UNEF 36,5 39,6
22 34,93 2,2 14,25 1-5/16-18UNEF 39,5 42,8
24 38,10 2,2 15,1 1-7/16-18UNEF 42,8 46,0
Backshell options
Type A Type F Type E
Shell size Ø DAL AVTHD Ø GFHFLFØ BEL E
min. max. Thread Type 2A min. max. max. max. max.
8 8,5 38,0 1/2-28UNEF 2,9 19,3 56,0 14,2 32,5
10 11,8 38,0 5/8-24UNEF 4,5 20,8 56,0 17,2 32,5
12 15,0 38,0 3/4-20UNEF 7,7 24,4 56,0 20,4 32,5
14 17,9 38,0 7/8-20UNEF 9,3 27,2 56,0 23,4 32,5
16 21,1 38,0 1-20UNEF 12,4 28,7 56,0 26,6 32,5
18 24,1 38,0 1-3/16-18UNEF 15,6 35,3 56,0 29,6 32,5
20 26,5 43,1 1-3/16-18UNEF 15,6 35,3 61,0 32,8 34,5
22 30,4 43,1 1-7/16-18UNEF 18,8 39,9 61,0 36,0 34,5
24 32,8 43,1 1-7/16-18UNEF 20,1 43,2 61,0 39,2 34,5
Mod. DN
Shell size Ø D2 L1 L2
– 0,5 max. ±0,5
8 15,6 35,0 12,2
10 18,4 35,0 12,2
12 23,7 35,0 12,2
14 24,5 35,0 12,2
16 29,8 37,0 14,5
18 32,0 37,0 14,5
20 36,1 42,0 15,8
22 38,5 42,0 15,8
24 41,6 42,0 14,9
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
18
BOX MOUNTING RECEPTACLE KPT02 / KPSE02 / KPTC2
KPT / KPSE / KPTC KPT / KPTC
Shell size Ø A L Ø N K M R S Ø T Z
max.
+0,03 – 0,13 max. max. ±0,1 ±0,15 ±0,15 max. ±0,15
8 12,00 21,1 11,1 1,9 11,6 15,1 21,0 3,05 12,3
10 15,00 21,1 14,3 1,9 11,6 18,3 24,2 3,05 12,3
12 19,05 21,1 17,5 1,9 11,6 20,6 26,6 3,05 12,3
14 22,23 21,1 20,6 1,9 11,6 23,0 29,0 3,05 12,3
16 25,40 21,1 23,8 1,9 11,6 24,6 31,3 3,05 12,3
18 28,58 21,1 27,0 1,9 11,6 27,0 33,7 3,05 12,3
20 31,75 22,7 30,2 2,2 14,25 29,4 36,9 3,05 10,8
22 34,93 22,7 33,4 2,2 14,25 31,8 40,1 3,05 10,8
24 38,10 22,7 36,5 2,2 15,1 34,9 43,3 3,75 10,0
THRU-BULKHEAD RECEPTACLES KPTB
Shell size Ø A K L M T R S Ø X
+0,03 – 0,13 ±0,1 max. ±0,25 max. ±0,15 max. ±0,15
8 12,00 1,8 28,6 14,5 6,0 15,1 21,0 3,05
10 15,00 1,8 28,6 14,5 6,0 18,3 24,2 3,05
12 19,05 1,8 28,6 14,5 6,0 20,6 26,6 3,05
14 22,23 1,8 28,6 14,5 6,0 23,0 29,0 3,05
16 25,40 1,8 28,6 14,5 6,0 24,6 31,3 3,05
18 28,58 1,8 28,6 14,5 6,0 27,0 33,7 3,05
20 31,75 2,5 31,9 17,7 9,2 29,4 36,9 3,05
22 34,93 2,5 31,9 17,7 9,2 31,8 40,1 3,05
24 38,10 2,5 31,9 17,7 8,0 34,9 43,3 3,75
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
19
STRAIGHT PLUGS KPT06 / KPSE06 / KPTC6
Shell size Ø G QTHD
max. Thread Type 2A
8 19,8 7/16-28UNEF
10 23,6 9/16-24UNEF
12 26,5 11/16-24UNEF
14 30,1 13/16-20UNEF
16 33,2 15/16-20UNEF
18 35,4 1-1/16-18UNEF
20 39,0 1-3/16-18UNEF
22 42,1 1-5/16-18UNEF
24 45,2 1-7/16-18UNEF
Backshell options
Type A Type F Type E
Shell size Ø DAL AVTHD Ø GFL FHFØ BEL E
min. max. Thread Type 2A min. max. max. max. max.
8 8,5 42,0 1/2-28UNEF 2,9 56,0 19,3 14,2 32,5
10 11,8 42,0 5/8-24UNEF 4,5 56,0 20,8 17,2 32,5
12 15,0 42,0 3/4-20UNEF 7,7 56,0 24,4 20,4 32,5
14 17,9 42,0 7/8-20UNEF 9,3 56,0 27,2 23,4 32,5
16 21,1 42,0 1-20UNEF 12,4 59,0 28,7 26,6 32,5
18 24,1 42,0 1-3/16-18UNEF 15,6 59,0 35,3 29,6 32,5
20 26,5 45,0 1-3/16-18UNEF 15,6 59,0 35,3 32,8 34,5
22 30,4 45,0 1-7/16-18UNEF 18,8 59,0 39,9 36,0 34,5
24 32,8 45,0 1-7/16-18UNEF 20,1 59,0 43,2 39,2 34,5
Mod. DN
Shell size Ø D2 L1 L2
– 0,5 max. ±0,5
8 15,6 35,0 12,2
10 18,4 35,0 12,2
12 23,7 35,0 12,2
14 24,5 35,0 12,2
16 29,8 37,0 14,5
18 32,0 37,0 14,5
20 36,1 42,0 15,8
22 38,5 42,0 15,8
24 41,6 42,0 14,9
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
20
STRAIGHT PLUG KPT6PG / KPTC6PG
Shell size Ø G Ø B C LPG PGTHD
max. max. min. max.
10 23,6 19,0 10,5 58,5 PG 09
12 26,5 22,5 10,5 58,5 PG 11
14 30,1 25,0 10,5 58,5 PG 13,5
16 33,2 28,0 10,5 73,0 PG 16
18 35,4 32,5 11,5 73,0 PG 21
20 39,0 34,5 11,5 76,0 PG 21
22 42,1 38,0 11,5 82,0 PG 21
24 45,2 40,5 11,5 82,0 PG 29
STRAIGHT PLUG KPT6ME / KPTC6ME
Shell size Ø G Ø B C LME Metric Thread
max. max. min. max.
10 23,6 19,0 10,5 58,5 M 12 x 1,5
12 26,5 22,5 10,5 58,5 M 16 x 1,5
14 30,1 25,0 10,5 58,5 M 20 x 1,5
16 33,2 28,0 10,5 73,0 M 25 x 1,5
18 35,4 32,5 11,5 73,0 M 25 x 1,5
20 39,0 34,5 11,5 76,0 M 25 x 1,5
22 42,1 38,0 11,5 82,0 M 32 x 1,5
24 45,2 40,5 11,5 82,0 M 32 x 1,5
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
21
JAM NUT RECEPTACLES KPT07 / KPSE07 / KPTC7
Shell size Ø A F H K M RTHD S T Panel thickness Ø N
+0,03 – 0,13 ±0,15 ±0,15 ±0,25 ±0,15 Thread Type 2A ±0,5 min. max. max.
8 12,00 13,3 19,0 3,2 17,7 9/16-24UNEF 24,0 1,6 3,5 28,0
10 15,00 16,5 22,2 3,2 17,7 11/16-24UNEF 27,0 1,6 3,5 31,0
12 19,05 20,6 27,0 3,2 17,7 7/8-20UNEF 32,0 1,6 3,5 36,0
14 22,23 23,8 30,2 3,2 17,7 1-20UNEF 35,0 1,6 3,5 39,0
16 25,40 26,9 33,3 3,2 17,7 1-1/8-18UNEF 38,5 1,6 3,5 42,0
18 28,58 30,1 36,5 3,2 17,7 1-1/4-18UNEF 41,5 1,6 3,5 45,0
20 31,75 33,3 39,7 4,0 22,5 1-3/8-18UNEF 46,0 1,6 6,5 50,0
22 34,93 36,5 42,9 4,0 22,5 1-1/2-18UNEF 49,5 1,6 6,5 55,0
24 38,10 39,6 46,0 4,0 23,3 1-5/8-18UNEF 52,5 1,6 6,5 57,0
Backshell options
Type F Type E Type DN Type A KPT / KPTC
Shell size LFØ GFHFØ BELEL1L2Ø D2Z
max. max. max. max. max. max. ±0,5 max. max.
8 44,9 2,9 19,3 18,2 33,5 43,0 12,2 15,6 7,9
10 44,9 4,5 20,8 21,5 33,5 43,0 12,2 18,4 7,9
12 44,9 7,7 24,4 24,6 33,5 43,0 12,2 23,7 7,9
14 44,9 9,3 27,2 27,8 33,5 43,0 12,2 24,7 7,9
16 48,4 12,4 28,7 31,0 33,5 45,5 14,5 29,8 7,9
18 48,4 15,6 35,3 34,1 33,5 45,5 14,5 32,0 7,9
20 50,3 15,6 35,3 38,1 39,0 52,6 15,8 36,1 4,7
22 50,3 18,8 39,9 41,3 39,0 52,6 15,8 28,5 4,7
24 50,3 20,1 43,2 44,5 39,0 51,6 14,9 41,6 3,8
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
22
RIGHT ANGLE PLUG, 90° KPT08 / KPSE08 / KPTC8
Shell size Ø G Q
max. Thread Type 2A
8 19,8 7/16-28UNEF
10 23,6 9/16-24UNEF
12 26,5 11/16-24UNEF
14 30,1 13/16-20UNEF
16 33,2 15/16-20UNEF
18 35,4 1-1/16-18UNEF
20 39,0 1-3/16-18UNEF
22 42,1 1-5/16-18UNEF
24 45,2 1-7/16-18UNEF
Backshell options
Type A and E Type F
Shell size LAE DAE VTHD L DFLF
max. max. Thread Type 2A max. max. max.
8 36,1 20,9 1/2-28UNEF 47,0 31,4 36,1
10 38,3 21,7 5/8-24UNEF 49,5 32,2 38,3
12 40,9 23,3 3/4-20UNEF 53,5 35,4 40,9
14 41,6 24,9 7/8-20UNEF 55,5 38,6 41,6
16 42,5 26,5 1-20UNEF 57,0 40,2 42,5
18 44,7 28,1 1-3/16-18UNEF 62,5 41,8 44,7
20 48,3 29,6 1-3/16-18UNEF 67,0 43,4 48,3
22 52,1 31,7 1-7/16-18UNEF 71,5 47,9 52,1
24 52,1 33,6 1-7/16-18UNEF 74,0 49,9 52,1
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
23
VERSIONS WITH GROUNDING CONTINUITY KPT / KPSE / KPTC
These connectors are designed to ensure electrical continuity
• at the cable shielding level to protect it against radio frequency interferences
• at the grounding level (if it is connected to the shielding)
The plugs are manufactured with grounding ngers xed to the front face of the shell. They make contact with the inner side of the
receptacle shell. Plug and receptacle feature a special backshell which supports the cable shielding. The connectors are in accordance
with the VG95328 specication.
RECEPTACLE WITH GROUNDING CONTINUITY (for shielded cable) KPT0E / KPSE0E / KPTC0E… DZ
Shell size Ø A Ø B Ø C Ø D E K L M R S Ø T
+0,03 – 0,13 min. ±0,5 max. ±1,0 ±0,1 max. ±0,15 ±0,15 max. ±0,15
8 12,00 6,6 16,0 13,3 15,0 1,9 52,0 11,6 15,1 21,0 3,05
10 15,00 9,2 18,0 16,1 15,0 1,9 52,0 11,6 18,3 24,2 3,05
12 19,05 12,2 22,0 20,0 17,0 1,9 52,0 11,6 20,6 26,6 3,05
14 22,23 15,2 25,0 22,2 18,0 1,9 53,0 11,6 23,0 29,0 3,05
16 25,40 18,3 28,0 26,2 18,0 1,9 53,0 11,6 24,6 31,3 3,05
18 28,58 20,0 32,0 28,5 18,0 1,9 53,0 11,6 27,0 33,7 3,05
20 31,75 23,0 34,0 32,5 18,0 2,2 58,0 14,25 29,4 36,9 3,05
22 34,93 26,0 38,0 34,8 18,0 2,2 58,0 14,25 31,7 40,1 3,05
24 38,10 28,8 41,0 37,9 18,0 2,2 58,0 15,1 34,9 43,3 3,75
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
24
CABLE CONNECTING PLUG WITH GROUNDING CONTINUITY (for shielded cable) KPT1E / KPSE1E / KPTC1E … DZ
Shell size Ø A M Ø B Ø C Ø D E K L S Ø Y
+0,03 – 0,13 ±0,15 min. ±0,5 max. ±1,0 ±0,1 max. max. max.
8 12,00 11,6 6,6 16,0 13,3 15,0 1,9 52,0 18,5 21,0
10 15,00 11,6 9,2 18,0 16,1 15,0 1,9 52,0 23,0 24,2
12 19,05 11,6 12,2 22,0 20,0 17,0 1,9 52,0 29,0 26,6
14 22,23 11,6 15,2 25,0 22,2 18,0 1,9 53,0 29,5 29,0
16 25,40 11,6 18,3 28,0 26,2 18,0 1,9 53,0 32,0 31,3
18 28,58 11,6 20,0 32,0 28,5 18,0 1,9 53,0 35,0 33,7
20 31,75 14,25 23,0 34,0 32,5 18,0 2,2 58,0 38,5 36,9
22 34,93 14,25 26,0 38,0 34,8 18,0 2,2 58,0 42,0 40,1
24 38,10 14,25 28,8 41,0 37,9 18,0 2,2 58,0 46,0 43,3
STRAIGHT PLUG WITH GROUNDING CONTINUITY KPT6E / KPSE6E / KPTC6E … DZ
Shell size Ø B Ø C Ø G Ø D E L S
min. +0,5 max. max. 1,0 max. +0,2
8 6,6 16,0 19,1 13,3 15,0 48,0 17,00
10 9,2 18,0 22,0 16,1 15,0 48,0 19,00
12 12,2 22,0 26,2 20,0 17,0 48,0 23,00
14 15,2 25,0 29,4 22,2 18,0 49,0 26,00
16 18,3 28,0 32,8 26,2 18,0 49,0 29,00
18 20,0 32,0 35,4 28,5 18,0 49,0 33,00
20 23,0 34,0 39,0 32,5 18,0 53,0 35,00
22 26,0 38,0 42,1 34,8 18,0 53,0 39,00
24 28,8 41,0 45,2 37,9 18,0 53,0 42,00
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
25
JAM NUT RECEPTACLE WITH GROUNDING CONTINUITY (for shielded cable) KPT 7E / KPSE 7E / KPTC … DZ
Shell size Ø A Ø B Ø C Ø D E L S T
min. +0,5 max. max. ±1,0 max. ±0,25 ±0,25
8 6,6 16,0 18,2 13,3 15,0 47,0 23,0 19,0
10 9,2 18,0 21,4 16,1 15,0 47,0 27,0 22,2
12 12,2 22,0 24,6 20,0 17,0 49,0 31,7 27,0
14 15,2 25,0 27,8 22,2 18,0 50,0 34,9 30,2
16 18,3 28,0 30,9 26,2 18,0 50,0 38,1 33,3
18 20,0 32,0 34,1 28,5 18,0 50,0 41,3 36,5
20 23,0 34,0 38,1 32,5 18,0 55,0 46,0 39,7
22 26,0 38,0 41,3 34,8 18,0 55,0 49,2 42,9
24 28,8 41,0 44,4 37,9 18,0 55,0 52,3 46,0
ASSEMBLY OF A CONNECTOR WITH A GROUND CONTINUITY BACKSHELL KPT / KPSE / KPTC … DZ
Shell size ØC
max.
8 6,6
10 9,2
12 12,2
14 15,2
16 18,3
18 20,0
20 23,0
22 26,0
24 28,8
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
26
BOX MOUNTING RECEPTACLE KPT2 / KPTC2 … EX OR EW
Shell size Ø A K L M Ø N R S Ø T
+0,03 – 0,13 ±0,1 max. ±0,15 max. ±0,15 max. ±0,15
8 12,00 1,9 21,1 11,60 11,1 15,1 21,0 3,05
10 15,00 1,9 21,1 11,60 14,3 18,3 24,2 3,05
12 19,05 1,9 21,1 11,60 17,5 20,6 26,6 3,05
14 22,23 1,9 21,1 11,60 20,6 23,0 29,0 3,05
16 25,40 1,9 21,1 11,60 23,8 24,6 31,3 3,05
18 28,58 1,9 21,1 11,60 27,0 27,0 33,7 3,05
20 31,75 2,2 22,7 14,25 30,2 29,4 36,9 3,05
22 34,93 2,2 22,7 14,25 33,4 31,7 40,1 3,05
24 38,10 2,2 22,7 15,10 36,5 34,9 43,3 3,75
JAM NUT RECEPTACLES KPT7 / KPTC7 … EX OR EW
Shell size Ø A F H K M RTHD S T (Panel Thickness) Ø N
+0,03 – 0,13 ±0,15 ±0,15 ±0,25 ±0,15 Thread Type 2A ±0,5 min. max. max.
8 12,0 13,3 19,0 3,2 17,7 9/16-24UNEF 24,0 1,6 3,5 28,0
10 15,0 16,5 22,2 3,2 17,7 11/16-24UNEF 27,0 1,6 3,5 31,0
12 19,1 20,6 27,0 3,2 17,7 7/8-20UNEF 32,0 1,6 3,5 36,0
14 22,2 23,8 30,2 3,2 17,7 1-20UNEF 35,0 1,6 3,5 39,0
16 25,4 26,9 33,3 3,2 17,7 1-1/8-18UNEF 38,5 1,6 3,5 42,0
18 28,6 30,1 36,5 3,2 17,7 1-1/4-18UNEF 41,5 1,6 3,5 45,0
20 31,8 33,3 39,7 4,0 22,5 1-3/8-18UNEF 46,0 1,6 6,5 50,0
22 34,9 36,5 42,9 4,0 22,5 1-1/2-18UNEF 49,5 1,6 6,5 55,0
24 38,1 39,6 46,0 4,0 23,3 1-5/8-18UNEF 52,5 1,6 6,5 57,0
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
27
PANEL CUTOUTS KPT / KPSE / KPTC
BOX MOUNTING RECEPTACLE
Shell size For rear mounting For front mounting
Ø D +0,25 / 0 Ø D +0,25 / 0 R ±0,15 Ø T +0,3
8 14,0 12,7 15,1 3,1
10 17,0 16,0 18,3 3,1
12 22,0 19,0 20,6 3,1
14 25,0 22,2 23,0 3,1
16 28,0 25,5 24,6 3,1
18 31,0 28,5 27,0 3,1
20 34,5 31,7 29,4 3,1
22 37,5 35,0 31,8 3,1
24 41,0 38,0 34,9 3,6
PANEL THICKNESS
Shell size P – Panel thickness
Height of screw head included
8 2,2
10 2,2
12 2,2
14 2,2
16 2,2
18 2,2
20 5,4
22 5,4
24 5,4
JAM NUT RECEPTACLE
Shell size KPT / KPSE KPT / KPSE
Ø A +0,25 / –0 B +0 / –0,12
8 14,5 13,6
10 17,7 16,8
12 22,7 20,9
14 25,7 24,1
16 28,8 27,2
18 32,0 30,4
20 35,1 33,6
22 38,4 36,8
24 41,5 40,0
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
28
PROTECTIVE CAPS KPT / KPSE / KPTC
Material Finishes
Protective cap Aluminum alloy A34 Nickel
Sash chain Stainless steel A232 Zinc cobalt, black
Cord Polyamide A233 Zinc cobalt, green
Ring Stainless steel A240 Zinc Nickel plating
Clip Aluminum alloy Standard (A66) Olive drab chromate over cadmium
Gasket Fluor Silicone
End link / rivet Stainless steel, passivated
Bayonet pin Stainless steel, passivated
Series
KPT80 – for plug
KPT81 – for receptacle
Shell size
8 – 24
Termination
D – Nylon cord 400 mm
Clip and end link attached (not assembled)
Crimp tool for end link: M317 (selector position 6)
C – sash chain and terminal link
CB – Nylon cord and terminal link
N – chain with ring (KPT81 only)
NB – Nylon cord with ring (KPT81 only)
Modication
A34 – Nickel plated (RoHS compliant)
A232 – Zinc cobalt, black (RoHS compliant)
A233 – Zinc cobalt, green
A240 – Zinc nickel plating (RoHS compliant)
A66 (without code) – Olive drab chromate over cadmium
Series
KPTC80 – for plug
KPTC81 – for receptacle
Shell size
8 – 24
Termination
C – Nylon cord and endlink
Modication
C – Nickel plated
D – Cadmium plated
R – Zinc cobalt, black
F – Zinc cobalt, green
H – Zinc nickel plating
VG Specication
Style
Z1 – for receptacle
Z2 – for plug
Z3 – for jam nut receptacle
Termination
A – chain and terminal link
C – for Z1 and Z2:
Nylon cord 400 mm and end link
Clip and end link attached (not mounted)
Crimp tool for end link: M317 (selector position 6)
C – for Z3: Nylon cord with ring
Shell size
8 – 24
KPT80- KPTC80-
VG95328
A34 C
10
D- C-
C
10 10
Z2
HOW TO ORDER
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
29
PROTECTIVE CAPS KPT / KPSE / KPTC
Cap with nylon cord
For receptacle
KPT81 termination D
VG95328 Z1 termination C
For plug
KPT80 termination D
VG95328 Z2 termination C
Cap with nylon cord and terminal link
For receptacle
KPT81 termination C and CB
VG95328 Z1 termination A
For plug
KPT80 termination C and CB
VG95328 Z2 termination A
Cap with nylon cord and ring
For receptacle
KPT81 termination N and NB
VG95328 Z3 termination C
Shell size Ø A L1Ø B L2H Ø N
max. max. max. max. max. ±0,5
8 18,26 19,84 18,0 21,44 76 14,7
10 21,44 19,84 20,3 21,44 76 17,9
12 25,40 19,84 25,1 21,44 89 22,6
14 28,58 19,84 28,2 21,44 89 25,8
16 31,75 19,84 31,5 21,44 89 29,0
18 34,92 19,84 34,5 21,44 89 32,2
20 38,10 21,44 37,8 21,44 101 35,3
22 41,28 21,44 40,9 21,44 101 38,5
24 44,45 22,22 44,2 22,22 101 41,7
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
30
DUMMY RECEPTACLES KPT/KPSE/KPTC
HOW TO ORDER
Series
Dummy receptacle
Shell size
Flange
A – Standard
MS
KPT
A
A
8
8
3115-
15-
Shell size Ø A K M R S Ø T
+0,03 – 0,13 ±0,4 ±0,15 ±0,15 max. ±0,15
* 8 A 12,00 1,6 12,1 15,1 21,0 3,05
* 10 A 15,00 1,6 12,1 18,3 24,2 3,05
* 12 A 19,05 1,6 12,1 20,6 26,6 3,05
* 14 A 22,23 1,6 12,1 23,0 29,0 3,05
* 16 A 25,40 1,6 12,1 24,6 31,3 3,05
* 18 A 28,58 1,6 12,1 27,0 33,7 3,05
* 20 A 31,75 2,4 14,5 29,4 36,9 3,05
* 22 A 34,93 2,4 14,5 31,8 40,1 3,05
* 24 A 38,10 2,4 15,4 34,9 43,3 3,75
* Add “KPT 15 -” or “MS 3115-” prexes
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
31
CROSS REFERENCE LIST KPT / KPSE / VG95328 / MIL-C-26482
Solder Crimp
ITT Cannon MIL-C-26482 VG95328 ITT Cannon MIL-C-26482 VG95328
KPT00E MS3110E KPSE00E MS3120E VG95328A
KPT00F MS3110F KPSE00F MS3120F VG95328B
KPT0E-DN KPSE0E-DN
KPT0E-DZ KPSE0E-DZ VG95328R
KPT01A KPSE01A
KPT01E MS3111E KPSE01E MS3121E
KPT01F MS3111F KPSE01F MS3121F
KPT1E-DN KPSE1E-DN
KPT1E-DZ KPSE1E-DZ
KPT02E MS3112E VG95328H KPSE02E MS3122E VG95328C
KPT06A KPSE06A
KPT06E MS3116E KPSE06E MS3126E
KPT06F MS3116F KPSE06F MS3126F VG95328K
KPT6E-DN KPSE6E-DN VG95328J
KPT6E-DZ KPSE6E-DZ VG95328M
KPT07A KPSE07A
KPT07E MS3114E KPSE07E MS3124E VG95328D
KPT07F MS3114F KPSE07F MS3124F VG95328E
KPT7E-DN KPSE7E-DN VG95328S
KPT7E-DZ KPSE7E-DZ VG95328T
KPT08E KPSE08E
KPT08F KPSE08F
KPTB MS3119 VG95328P
CROSS REFERENCE LIST PROTECTIVE CAPS KPT / VG95328 / MIL-C-26482
Part No.
ITT Cannon
Part No.
MIL-C-26482
Part No.
VG95328
KPT80 MS3180
KPT80..C Z2...VG95328
KPT81 MS3181
KPT81..C Z1...VG95328
KPT81..N MS 3181..N
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
32
TOOLS AND ACCESSORIES KPT / KPSE / KPTC
TOOLS KPSE / KPTC
Tool Designation Order reference Locator* Order reference Test gage Order reference
Hand crimp tool M22520/1-01 995-0001-585 M22520/1-02 995-0001-736 M22520/3-1 995-0001-684
Crimp machine WA27F-CE 121586-5067 M22520/1-02 995-0001-736 M22520/3-1 995-0001-684
Crimp machine HACS HACS – – – –
* for contact sizes 20, 16, 12
KPSE
Contact size Insertion tool Order reference Old designation Extraction tool Order reference Extraction TIP
20* – 038894-0018 CIT-20-16 MS2425R20 995-0001-965 317-7130-000
20** M24256A20 995-0001-950 CIT-20-5A MS2425R20 995-0001-965 317-7130-000
16 M24256A16 995-0001-951 CIT-16-1 MS2425R16 995-0001-964 317-7129-000
12 M24256A12 995-0001-913 – MS2425R12 995-0001-966 317-7131-000
* without insulation support ** with insulation support
KPTC
Contact size Insertion tool Order ref. Insertion pliers Order ref. Extraction tool Extraction TIP
20 CITG-20A 12086-3104 CIT-KPTC-20 121086-3101 CET-KPTC-20 CET-KPTC-20-TIP
16 CIT-16 121086-3008 CIT-F80-16 121086-0097 CET-KPTC-16 CET-KPTC-16-TIP
KPT14A4
Contact type Insertion tool Order reference Old designation Extraction tool Order reference LN
Coaxial – – – CET-C6B 070064-0000 –
CONTACTS KPT / KPSE / KPTC /
VG95328
KPSE / VG95328
Contact size Contact type Contact order reference
KPSE version VG95328 version
20 Socket with insulation support 031-8704-203 031-8704-203
Pin with insulation support 430-8560-006 430-8560-006
16 Socket 031-8704-000 031-8704-000
Pin 430-8560-004 430-8560-004
12 Socket 031-8704-012
Pin 430-8560-016
Grounding pin 430-8560-020
KPTC
Contact size Order reference (hard gold plated) For shell size 8 and contact arrangements 12-14 only:
20 Socket 031-8704-508 Contact size Order reference
Pin 430-8560-404 hard gold plated hard silver plated
16 Socket 031-8704-502 20 Socket 031-8704-509 031-8704-506
Pin 430-8560-406 20 Pin 430-8560-411 430-8560-410
KPT14A4
Coaxial Pin DM 53740-5001
Socket DM 53742-5001
WIRE HOLE FILLERS
KPSE / KPTC
KPSE/KPTC
Contact size Colour code MS Cannon
20 Red MS3187A20 225-1012-000
16 Blue MS3187-16A 225-1011-000
12* Yellow MS3187-12 225-0072-000
Coaxial 14A4* Yellow – 225-0018-000
* KPSE only
GASKETS KPT / KPSE / KPTC KPT / KPSE / KPTC
Shell size Alu-Flex Chloroprene Shell size Alu-Flex Chloroprene
conductive non conductive conductive non conductive
8 075-8543-000 075-8543-010 18 075-8543-005 075-8543-015
10 075-8543-001 075-8543-011 20 075-8543-006 075-8543-016
12 075-8543-002 075-8543-012 22 075-8543-007 075-8543-017
14 075-8543-003 075-8543-013 24 075-8543-008 075-8543-018
16 075-8543-004 075-8543-014
www.ittcannon.com
Dimensions shown in mm | Specications and dimensions subject to change
33
KPSE CONTACT AND SEALING PRINCIPLE
Standard MIL-C-26482 or Hardware mates with any
connector designed to MIL-C-26482 and VG95328 model
Monobloc insulator does not leave any access to
moisture and avoids interfacial empty space.
Positive insert-to-shell mechanical retention with hard
plastic wafer rmly locked into a groove in the shell, in addi-
tion to a strong adhesive bond between the insert and shell.
Crimp, snap-in contacts are designed to SAE-AS-39029
and can be crimped with the standard M22520/1 crimp
tool.
CLOSED-ENTRY SOCKET CONTACTS eliminate damage
from abuse by test probes and help to correct any
misaligned pins during engagement.
CONTACT INSERTION is accomplished from the rear of
the connector. When the contact is fully inserted, the clip
tines snap securely behind the contact shoulder.
CONTACT EXTRACTION is accomplished with a front-
inserted extraction tool. Pressing the tool plunger pushes
the contact out through the rear of the connector.
Contact retention
RETAINING CLIP: completely encased in a tough plastic
wafer to protect the clip from damage
PLASTIC WAFER: latest version for easier and faster assem-
bly and disassembly of contacts (used on selected layouts)
Complete moisture sealing is achieved by combining
four seals: shell, peripheral, interfacial and wire seals.
SHELL SEAL is effected when the plug shell pushes against
the sealing ring in the receptacle when the connectors are
mated.
PERIPHERAL SEAL around the edge of the pin insulator is
designed so that mating the connector puts tension on
the seal and greatly reduces compression set.
INTERFACIAL SEAL is achieved by the insulator faces
meeting when the plug and receptacle are mated.
WIRE SEAL is accomplished by a multiple ripple design,
exceeding the wire sealing requirements of MIL-C-26482.
1
3 5
2
4
• High performance
• Crimp termination
• Closed entry socket contacts
Series KPSE environmental, miniature circular, quick disconnect
connectors are designed for the extracting requirements of today’s
electronic industry.
They are intermateable, intermountable and interchangeable
with all connectors manufactured according to MIL-C-26482,
VG95328 and HE 301.
Connectors of Cannon series KPSE have obtained the
VDE Expertise No. 63761.
www.ittcannon.com34
PRODUCT SAFETY INFORMATION
1. MATERIAL CONTENT AND PHYSICAL
FORM
Electrical connectors do not usually contain
hazardous materials. They contain
conducting and non-conducting materials
and can be divided into two groups.
a) Printed circuit types and low cost audio
types which employ all plastic insulators and
casings.
b) Rugged, Fire Barrier and High Reliability
types with metal casings and either natural
rubber, synthetic rubber, plastic or glass
insulating materials. Contact materials vary
with type of connector and also application
and are usually manufactured from either:
Copper, copper alloys, nickel, alumel,
chromel or steel. In special applications,
other alloys may be specied.
2. FIRE CHARACTERISTICS AND ELECTRIC
SHOCK HAZARD
There is no re hazard when the connector
is correctly wired and used within the spec-
ied parameters.
Incorrect wiring or assembly of the connector
or careless use of metal tools or conductive
uids, or transit damage to any of the
component parts may cause electric shock
or burns. Live circuits must not be broken
by separating mated connectors as this may
cause arcing, ionization and burning. Heat
dissipation is greater at maximum resistance
in a circuit. Hot spots may occur when resis
-
tance is raised locally by damage, e.g.
cracked or deformed contacts, broken
strands of wire. Local overheating may also
result from the use of the incorrect applica-
tion tools or from poor quality soldering or
slack screw terminals. Overheating may
occur if the ratings in the product Data
Sheet/Catalog are exceeded and can cause
breakdown of insulation and hence electric
shock. If heating is allowed to continue it
intensies by further increasing the local
resistance through loss of temper of spring
contacts, formation of oxide lm on contacts
and wires and leakage currents through
carbonization of insulation and tracking
paths. Fire can then result in the presence
of combustible materials and this may
release noxious fumes. Overheating may not
be visually apparent. Burns may result from
touching overheated components.
3. HANDLING
Care must be taken to avoid damage to any
component parts of electrical connectors
during installation and use. Although there
are normally no sharp edges, care must be
taken when handling certain components
to avoid injury to ngers.
Electrical connectors may be damaged in
transit to the customers, and damage may
result in creation of hazards. Products
should therefore be examined prior to instal-
lation/use and rejected if found to be
damaged.
4. DISPOSAL
Incineration of certain materials may release
noxious or even toxic fumes.
5. APPLICATION
Connectors with exposed contacts should
not be selected for use on the current supply
side of an electrical circuit, because an elec-
tric shock could result from touching
exposed contacts on an unmated connector.
Voltages in excess of 30 V ac or 42.5 V DC
are potentially hazardous and care should
be taken to ensure that such voltages cannot
be transmitted in any way to exposed metal
parts of the connector body. The connector
and wiring should be checked, before
making live, to have no damage to metal
parts or insulators, no solder blobs, loose
strands, conducting lubricants, swarf, or any
other undesired conducting particles. Circuit
resistance and continuity check should be
made to make certain that there are no high
resistance joints or spurious conducting
paths. Always use the correct application
tools as specied in the Data Sheet/Catalog.
Do not permit untrained personnel to wire,
assemble or tamper with connectors. For
operation voltage please see appropriate
national regulations.
IMPORTANT GENERAL INFORMATION
(i) Air and creepage paths/Operating
voltage. The admissible operating voltages
depend on the individual applications and
the valid national and other applicable
safety regulations. For this reason the air
and creepage path data are only reference
values. Observe reduction of air and
creepage paths due to PC board and/or
harnessing.
(ii) Temperature
All information given are temperature limits.
The operation temperature depends on the
individual application.
(iii) Other important information
Cannon continuously endeavors to improve
their products. Therefore, Cannon products
may deviate from the description, technical
data and shape as shown in this catalog and
data sheets.
ITT's Interconnect Solutions, is a division of
ITT Corporation who manufactures the
highest quality products available in the
marketplace; however these products are
intended to be used in accordance with the
specications in this publication. Any use or
application that deviates from the stated
operating specifications is not recom-
mended and may be unsafe. No information
and data contained in this publication shall
be construed to create any liability on the
part of Cannon. Any new issue of this publi-
cation shall automatically invalidate and
supersede any and all previous issues.
Product Warranty
A limited warranty applies to Cannon prod-
ucts. In general, except for obligations
assumed by Cannon under this warranty,
Cannon shall not be liable for any loss,
damage, cost of repairs, incidental or conse-
quential damages of any kind, whether or
not based on express or implied warranty,
contract, negligence or strict liability arising
in connection with the design, manufacture,
sale, use or repair of the products. Product
availability, prices and delivery dates are
exclusively subject to our respective order
conrmation form; the same applies to
orders based on development samples deliv-
ered. Please refer to www.ittcannon.com
(General Terms of Sale) for the complete text
of Cannon’s applicable Terms and Condi-
tions, including Warranty.
This publication is not to be construed as an
offer. It is intended merely as an invitation
to make an offer. By this publication, Cannon
does not assume responsibility or any
liability for any patent infringements or
other rights of third parties which may result
from its use.
Reprinting this publication is generally
permitted, indicating the source. However,
Cannon’s prior consent must be obtained in
all cases. “Engineered for life” is a registered
trademark of ITT Corporation ©2012. All
other trademarks or registered trademarks
are property of their respective owners. All
data subject to change without notice.
This document does not contain technical
data whose export is restricted by the Arms
Export Control Act (Title 22, U.S.C., App
2401 et. Seq.)
www.ittcannon.com 35
Circular / Filter / Hermetic / Fiber Optic Connectors
As a world leader in circular, lter, and hermetic connectors, ITT can
leverage its design and manufacturing expertise to t virtually any
application. Our expertise includes fast positive mating for a
wide range of military applications, as well as numerous sizes
and contact congurations for various harsh environments. Our
wide variety of ber optic products include hybrid contacts,
multi-channel, rack and panel, and hi-rel assemblies, including MIL
and ARINC standard solutions that meet numerous specications,
including NATO and MIL standards.
D-Subminiature Connectors
Cannon invented D-sub connectors in 1952. Our family of D-Subs
now includes combinations of signal, power and RF, as well as
severe service sealed connectors. Cannon D-Subs are available
with an extensive line of backshells and accessories and are one
of the most economical shielded connector solutions available. ITT
D-Sub connectors are qualied to the MIL-DTL-24308 specication.
Microminiature Connectors
Developed rst by Cannon in the 1960’s, ITT's Interconnect Solutions
microminiature connectors offer high performance and reliability
with exceptional versatility. Available in rectangular, circular, and strip
congurations for countless applications, many of our connectors meet
or exceed applicable requirements of the MIL-DTL-83513 specication.
Rack and Panel Connectors
Initially pioneered by Cannon during the 1930s, ITT's Interconnect Solutions
is the world leader in rack and panel connectors, offering unmatched
variety of shell congurations and insert arrangements, materials, plating,
and contact options. Many of our standard and custom designs meet the
stringent requirements of ARINC 600, ARINC 404 (MIL-C-81659), and
MIL-DTL-83733 standards.
Trident
Cannon’s Trident Connector System is a versatile range of electrical
connectors based on a standard contact design. These contacts are fully
interchangeable throughout the Trident Connector System. The connector
options include low cost rectangular, rack and panel, industrial grade
circulars, harsh environment circulars and shielded circulars.
Transportation
The ITT's Interconnect Solutions includes sealed circular and rectangular connectors in
metal or plastic shells. These congurations include board to cable or cable to cable /
bulkhead applications. Both signal and power contacts can be combined in various
layouts. All product lines within the Transportation segment offer very low contact
resistance providing maximum signal integrity.
ITT's Interconnect Solutions is an international manufacturer and supplier of connectors including circular, rectangular, ber optic, RF, power and
high voltage, audio, PMCIA, Compact Flash Card, enclosures, cable assemblies, and application specic custom solutions. The Interconnect
Solutions portfolio includes the brands Cannon, VEAM, and BIW Connector Systems. As a worldwide leader in connector technology for nearly a
century, ITT offers one of the broadest product offerings, six sigma manufacturing capability, Value Based Product Development with exception-
al engineering capability, and an extensive sales, distribution, and customer support network.
ITT Interconnect Solutions
Cannon, VEAM,
BIW Connector Systems
Visit our website at
www.ittcannon.com
© 2013 ITT Corporation ”Engineered for life” and “Cannon” are registered trademarks of
ITT Corporation. Specication and other data are based on information available at the time
of printing, and are subject to change without notice.
Global Design &
Manufacturing
Customer Support
CHINA – Cannon, VEAM
Tuopandun Industrial Area,
Jinda Cheng, Xiner Village, Shajing Town,
Boan District, Shenzhen City,
Guangdong Province, China 518125
phone: +86.755.2726.7238
fax: +86.755.2726.7515
HONG KONG – Cannon, VEAM
Units 2405-6, 24/F, ING Tower
308 Des Voeux Road Central
Hong Kong
phone: +852.2732.2720
fax: +852.2732.2919
INDIA – Cannon, VEAM
ITT Corporation India Pvt Ltd
Money Chamber, Unit No. 202
#6, KH Road, Bangalore
560027
phone: +91 22 67843000
fax: +91 22 26783033
JAPAN – Cannon, VEAM
5-11-3, Hibarigaoka,
Zama-shi, Kanagawa, Japan 252-0003
phone: +81.462.57.2010
fax: +81.462.57.1680
SINGAPORE – Cannon, VEAM
10 Jalan Kilang #06-01
Singapore 159410
phone: +65.62763693 ext 232
fax: +65.62763685
FRANCE – Cannon, VEAM
15, Boulevard Robert Thiboust
Serris, France 77700
phone: +33.1.60.04.93.93
fax: +33.1.60.04.93.90
GERMANY – Cannon, VEAM
Cannonstrasse 1
71384 Weinstadt
phone: +49.7151.699.0
fax: +49.7151.699.217
ITALY – VEAM
Corso Europa 41/43
Lainate (MI), Italy 20020
phone: +39.02938721
fax: +39.0293872300
LEBANON – BIW Connector
Systems
P.O. Box 199
Jounieh
Lebanon
phone: +961.9.911.560
fax: +961.9.912.126
UK – Cannon, VEAM
Jays Close, Viables Estate
Basingstoke, RG22 4BA
phone: +44.1256.311200
fax: +44.1256.323356
North America Europe & Middle East Asia
MEXICO – Cannon, VEAM
Av. Libre Comercio s/n-
entre Calzada Industrial
Nuevo Nogales y Calzada del Raquet Club,
Parque Industrial Nuevo Nogales
phone: +52.631.3110050
fax: +52.631.3110060
USA – Cannon
666 East Dyer Road
Santa Ana, CA 92705
toll free: +1.800.854.3028
phone: +1.714.557.4700
fax: +1.714.628.2142
USA – BIW Connector Systems
500 Tesconi Circle
Santa Rosa, CA 95401
phone: +1.707.523.2300
fax: +1.707.523.3567
USA - VEAM
100 New Wood Road
Watertown, CT 06795
phone: +1.860.274.9681
fax: +1.860.274.4963