DUAL MONOSTABLE MULTIVIBRATORS WITH SCHMITT-TRIGGER INPUTS Each multivibrator of the LS221 features a negative-transition-triggered input and a positive-transition-triggered input either of which can be used as an inhibit input. Pulse triggering occurs at a voltage level and is not related to the transition time of the input pulse. Schmitt-trigger input circuitry for B input allows jitter-free triggering for inputs as slow as 1 volt/ second, providing the circuit with excellent noise immunity. A high immunity to VCC noise is also provided by internal latching circuitry. Once triggered, the outputs are independent of further transitions of the inputs and are a function of the timing components. The output pulses can be terminated by the overriding clear. Input pulse width may be of any duration relative to the output pulse width. Output pulse width may be varied from 35 nanoseconds to a maximum of 70 s by choosing appropriate timing components. With R ext = 2.0 k and C ext = 0, a typical output pulse of 30 nanoseconds is achieved. Output rise and fall times are independent of pulse length. Pulse width stability is achieved through internal compensation and is virtually independent of VCC and temperature. In most applications, pulse stability will only be limited by the accuracy of external timing components. Jitter-free operation is maintained over the full temperature and VCC ranges for greater than six decades of timing capacitance (10 pF to 10 F), and greater than one decade of timing resistance (2.0 to 70 k for the SN54LS221, and 2.0 to 100 k for the SN74LS221). Pulse width is defined by the relationship: tw(out) = CextRext ln 2.0 0.7 Cext Rext; where tW is in ns if Cext is in pF and Rext is in k . If pulse cutoff is not critical, capacitance up to 1000 F and resistance as low as 1.4 k may be used. The range of jitter-free pulse widths is extended if VCC is 5.0 V and 25C temperature. * SN54LS221 and SN74LS221 is a Dual Highly Stable One-Shot * Overriding Clear Terminates Output Pulse * Pin Out is Identical to SN54/ 74LS123 SN54/74LS221 DUAL MONOSTABLE MULTIVIBRATORS WITH SCHMITT-TRIGGER INPUTS LOW POWER SCHOTTKY J SUFFIX CERAMIC CASE 620-09 16 1 N SUFFIX PLASTIC CASE 648-08 16 1 16 1 ORDERING INFORMATION SN54LSXXXJ SN74LSXXXN SN74LSXXXD INPUTS Ceramic Plastic SOIC FUNCTION TABLE (EACH MONOSTABLE) (TOP VIEW) D SUFFIX SOIC CASE 751B-03 A B Q Q L X X H H X H X L X X L H L L L H H H * L H *See operational notes -- Pulse Trigger Modes TYPE positive logic: Low input to clear resets Q low and positive logic: Q high regardless of dc levels at A positive logic: or B inputs. SN54LS221 SN74LS221 FAST AND LS TTL DATA 5-380 OUTPUTS CLEAR TYPICAL POWER DISSIPATION 23 mW 23 mW MAXIMUM OUTPUT PULSE LENGTH 49 s 70 s SN54/74LS221 OPERATIONAL NOTES Once in the pulse trigger mode, the output pulse width is determined by tW = RextCextIn2, as long as Rext and Cext are within their minimum and maximum valves and the duty cycle is less than 50%. This pulse width is essentially independent of VCC and temperature variations. Output pulse widths varies typically no more than 0.5% from device to device. If the duty cycle, defined as being 100 * tW where T is the T input period of the input pulse, rises above 50%, the output pulse width will become shorter. If the duty cycle varies between low and high valves, this causes the output pulse width to vary in length, or jitter. To reduce jitter to a minimum, Rext should be as large as possible. (Jitter is independent of Cext). With Rext = 100K, jitter is not appreciable until the duty cycle approaches 90%. Although the LS221 is pin-for-pin compatible with the LS123, it should be remembered that they are not functionally identical. The LS123 is retriggerable so that the output is dependent upon the input transitions once it is high. This is not the case for the LS221. Also note that it is recommended to externally ground the LS123 Cext pin. However, this cannot be done on the LS221. The SN54LS/74LS221 is a dual, monolithic, non-retriggerable, high-stability one shot. The output pulse width, tW can be varied over 9 decades of timing by proper selection of the external timing components, Rext and Cext. Pulse triggering occurs at a voltage level and is, therefore, independent of the input slew rate. Although all three inputs have this Schmitt-trigger effect, only the B input should be used for very long transition triggers (1.0 V/s). High immunity to VCC noise (typically 1.5 V) is achieved by internal latching circuitry. However, standard VCC bypassing is strongly recommended. The LS221 has four basic modes of operation. Clear Mode: Inhibit Mode: If either the A input is high or the B input is low, once the Q output goes low, it cannot be retriggered by other inputs. Pulse Trigger Mode: A transition of the A or B inputs as indicated in the functional truth table will trigger the Q output to go high for a duration determined by the tW equation described above; Q will go low for a corresponding length of time. The Clear input may also be used to trigger an output pulse, but special logic preconditioning on the A or B inputs must be done as follows: Following any output triggering action using the A or B inputs, the A input must be set high OR the B input must be set low to allow Clear to be used as a trigger. Inputs should then be set up per the truth table (without triggering the output) to allow Clear to be used a trigger for the output pulse. If the Clear pin is routinely being used to trigger the output pulse, the A or B inputs must be toggled as described above before and between each Clear trigger event. Once triggered, as long as the output remains high, all input transitions (except overriding Clear) are ignored. Overriding Clear Mode: FAST AND LS TTL DATA 5-381 If the clear input is held low, irregardless of the previous output state and other input states, the Q output is low. If the Q output is high, it may be forced low by bringing the clear input low. SN54/74LS221 GUARANTEED OPERATING RANGES Symbol Parameter Min Typ Max Unit VCC Supply Voltage 54 74 4.5 4.75 5.0 5.0 5.5 5.25 V TA Operating Ambient Temperature Range 54 74 - 55 0 25 25 125 70 C IOH Output Current -- High 54, 74 - 0.4 mA IOL Output Current -- Low 54 74 4.0 8.0 mA DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol VT+ Positive-Going Threshold Voltage at C Input VT- Negative-Going Threshold Voltage at C Input VT+ Positive-Going Threshold Voltage at B Input VT- Negative-Going Threshold Voltage at B Input VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Voltage VOH Output HIGH Voltage VOL Output LOW Voltage IIH Input HIGH Current IIL Input LOW Current Input A Input B Clear IOS Short Circuit Current (Note 1) ICC Min Parameter Power Supply Current Quiescent Triggered Typ Max Unit 1.0 2.0 V 54 0.7 0.8 V 74 0.7 0.8 V 1.0 2.0 V 54 0.7 0.9 V 74 0.8 0.9 V 2.0 54 0.7 74 0.8 - 1.5 Test Conditions VCC = MIN VCC = MIN VCC = MIN VCC = MIN V Guaranteed Input HIGH Voltage for A Input V Guaranteed Input LOW Voltage for A Input V VCC = MIN, IIN = - 18 mA 54 2.5 3.4 V 74 2.7 3.4 V VCC = MIN, IOH = MAX 54 0.25 0.4 V IOL = 4.0 mA 74 0.35 0.5 V IOL = 8.0 mA 20 A VCC = MAX, VIN = 2.7 V 0.1 mA VCC = MAX, VIN = 7.0 V mA VCC = MAX, VIN = 0.4 V - 100 mA VCC = MAX 4.7 11 mA VCC = MAX 19 27 - 0.4 - 0.8 - 0.8 - 20 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. FAST AND LS TTL DATA 5-382 VCC = MIN SN54/74LS221 AC CHARACTERISTICS (VCC = 5.0 V, TA = 25C) From (Input) To (Output) A Limits Typ Max Q 45 70 B Q 35 55 A Q 50 80 B Q 40 65 tPHL Clear Q 35 55 ns tPLH Clear Q 44 65 ns 70 120 150 20 47 70 600 670 750 6.0 6.9 7.5 Symbol tPLH tPHL tW(out) Min Unit Test Conditions ns Cext = 80 pF, Rext = 2.0 ns A or B CL = 15 pF, See Figure 1 Cext = 80 pF, Rext = 2.0 Cext = 0, Rext = 2.0 k ns Q or Q Cext = 100 pF, Rext = 10 k Cext = 1.0 F, Rext = 10 k ms AC SETUP REQUIREMENTS (VCC = 5.0 V, TA = 25C) Limits Symbol Min Parameter Typ Max Unit Rate of Rise or Fall of Input Pulse dv/dt Schmitt, B 1.0 V/s Logic Input, A 1.0 V/s A or B, tW(in) 40 ns Clear, tW (clear) 40 Input Pulse Width tW ts Clear-Inactive-State Setup Time Rext External Timing Resistance Cext External Timing Capacitance 15 ns 54 1.4 70 74 1.4 100 0 1000 F RT = 2.0 k 50 % RT = MAX Rext 90 k Output Duty Cycle FAST AND LS TTL DATA 5-383 SN54/74LS221 AC WAVEFORMS ! ! ! ! ! TRIGGER FROM B, THEN CLEAR -- CONDITION 1 TRIGGER FROM B, THEN CLEAR -- CONDITION 2 ! !"! CLEAR OVERRIDING B, THEN TRIGGER FROM B TRIGGERING FROM POSITIVE TRANSITION OF CLEAR Figure 1 FAST AND LS TTL DATA 5-384 Case 751B-03 D Suffix 16-Pin Plastic SO-16 -A- "! ! " " ! " # 1 %# ) ! !" $ !" 8 C -T- D M K " ! #! J F ! Case 648-08 N Suffix 16-Pin Plastic R X 45 G " ! ) #! P ! " " 9 -B- ! 16 & ! ! ( ( ( ( "! ! " " ! ! ' " " ! ' ! " # & -A- 16 9 1 8 ! ! $ ! B # ) " ! " # ) !" $ !" ) F L C S -T- K H G M J D " Case 620-09 J Suffix 16-Pin Ceramic Dual In-Line -A- ! ! ! ! "! ! " 16 " ) " L K M N J G D " $ " $ ! " " ! ! FAST AND LS TTL DATA 5-385 & # ) !" $ !" ) -T $ " " C F & 8 E ! ! ! " " -B1 & 9 * * ! ! ! ! * * ! ! Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. FAST AND LS TTL DATA 5-386