Ericsson Internal PRODUCT TABLE OF CONTENTS SPECIFICATION E Prepared (also subject responsible if other) SEC/S David Xie Approved PKU 4000B PI EAB/FJB/GMF (Natalie Johansson) 1 (4) (1) No. 1/1301-BMR 654Technical Uen Specification Checked Date MICNAJO MICIOLE 2009-02-10 2009-02-02 Rev Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Reference EN/LZT 146 376 R2A February 2009 C D (c) Ericsson AB Key Features * Industry standard Sixteenth-brick 27.9 x 22.8 x 8.3 mm (1.1 x 0.9 x 0.327 in.) * High efficiency, typ. 93.4 % at 5 Vout 50 % load * 1500 Vdc input to output isolation * Meets safety requirements according to IEC/EN/UL 60950 * More than 1.6 million hours MTBF General Characteristics * 1+1 parallelable * Input under voltage protection * Over temperature protection * Output over voltage protection * Output short circuit protection * Remote control * Highly automated manufacturing ensures quality * ISO 9001/14001 certified supplier Safety Approvals Design for Environment Meets requirements in hightemperature lead-free soldering processes. Contents General Information Safety Specification Absolute Maximum Ratings ............................................................. 2 ............................................................. 3 ............................................................. 4 Product Program 5.0V, 20 A / 100 W Electrical Specification Ordering No. PKU 4101B PI ...................................... 5 EMC Specification Operating Information Thermal Consideration Connections Mechanical Information Soldering Information Delivery Information Product Qualification Specification ............................................................. 8 ............................................................. 9 ........................................................... 10 ........................................................... 10 ........................................................... 11 ........................................................... 13 ........................................................... 14 ........................................................... 15 Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) SEC/S David Xie Approved PKU 4000B PI EAB/FJB/GMF (Natalie Johansson) 2 (4) No. 1/1301-BMR 654Technical Uen Specification Checked Date MICNAJO 2009-02-10 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Rev Reference 2 EN/LZT 146 376 R2A February 2009 C (c) Ericsson AB General Information Ordering Information Compatibility with RoHS requirements See Contents for individual product ordering numbers. The products are compatible with the relevant clauses and requirements of the RoHS directive 2002/95/EC and have a maximum concentration value of 0.1% by weight in homogeneous materials for lead, mercury, hexavalent chromium, PBB and PBDE and of 0.01% by weight in homogeneous materials for cadmium. Option Suff Ordering No. ix Surface mount SI PKU 4101B SI Positive Remote Control Logic P PKU 4101B PIP Lead length 3.69 mm (0.145 in) LA PKU 4101B PILA Lead length 4.57 mm (0.180 in) LB PKU 4101B PILB Note 1: If several options needed below sequence is to be used: Positive logic option, LA length Example: PKU4101BPIPLA Reliability The Mean Time Between Failure (MTBF) is calculated at full output power and an operating ambient temperature (TA) of +40C. Different methods could be used to calculate the predicted MTBF and failure rate which may give different results. Ericsson Power Modules currently uses two different methods, Ericsson failure rate data system DependTool and Telcordia SR332. Predicted MTBF for the series is: 1.6 million hours according to Telcordia SR332, issue 1, Black box technique. The Ericsson failure rate data system is based on field tracking data. The data corresponds to actual failure rates of components used in Information Technology and Telecom (IT&T) equipment in temperature controlled environments (TA = -5...+65C). Telcordia SR332 is a commonly used standard method intended for reliability calculations in IT&T equipment. The parts count procedure used in this method was originally modelled on the methods from MIL-HDBK-217F, Reliability Predictions of Electronic Equipment. It assumes that no reliability data is available on the actual units and devices for which the predictions are to be made, i.e. all predictions are based on generic reliability parameters. Exemptions in the RoHS directive utilized in Ericsson AB products include: Lead in high melting temperature type solder (used to solder the die in semiconductor packages) Lead in glass of electronics components and in electronic ceramic parts (e.g. fill material in chip resistors) Lead as an alloying element in copper alloy containing up to 4% lead by weight (used in connection pins made of Brass) Quality Statement The products are designed and manufactured in an industrial environment where quality systems and methods like ISO 9000, 6 (sigma), and SPC are intensively in use to boost the continuous improvements strategy. Infant mortality or early failures in the products are screened out and they are subjected to an ATE-based final test. Conservative design rules, design reviews and product qualifications, plus the high competence of an engaged work force, contribute to the high quality of our products. Warranty Warranty period and conditions are defined in Ericsson AB General Terms and Conditions of Sale. Limitation of Liability Ericsson AB does not make any other warranties, expressed or implied including any warranty of merchantability or fitness for a particular purpose (including, but not limited to, use in life support applications, where malfunctions of product can cause injury to a person's health or life). Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) SEC/S David Xie Approved PKU 4000B PI EAB/FJB/GMF (Natalie Johansson) 3 (4) No. 1/1301-BMR 654Technical Uen Specification Checked Date Rev MICNAJO 2009-02-10 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Reference 3 EN/LZT 146 376 R2A February 2009 C (c) Ericsson AB Safety Specification General information Ericsson AB DC/DC converters and DC/DC regulators are designed in accordance with safety standards IEC/EN/UL60950, Safety of Information Technology Equipment. IEC/EN/UL60950 contains requirements to prevent injury or damage due to the following hazards: * * * * * * Electrical shock Energy hazards Fire Mechanical and heat hazards Radiation hazards Chemical hazards Isolated DC/DC converters It is recommended that a slow blow fuse with a rating twice the maximum input current per selected product be used at the input of each DC/DC converter. If an input filter is used in the circuit the fuse should be placed in front of the input filter. In the rare event of a component problem in the input filter or in the DC/DC converter that imposes a short circuit on the input source, this fuse will provide the following functions: * * Isolate the faulty DC/DC converter from the input power source so as not to affect the operation of other parts of the system. Protect the distribution wiring from excessive current and power loss thus preventing hazardous overheating. On-board DC-DC converters are defined as component power supplies. As components they cannot fully comply with the provisions of any Safety requirements without "Conditions of Acceptability". It is the responsibility of the installer to ensure that the final product housing these components complies with the requirements of all applicable Safety standards and Directives for the final product. The galvanic isolation is verified in an electric strength test. The test voltage (Viso) between input and output is 1500 Vdc or 2250 Vdc for 60 seconds (refer to refer to Absolute maximum ratings). Leakage current is less than 100 A at nominal input voltage. Component power supplies for general use should comply with the requirements in IEC60950, EN60950 and UL60950 "Safety of information technology equipment". 24 V DC systems The input voltage to the DC/DC converter is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions. There are other more product related standards, e.g. EC61204-7 "Safety standard for power supplies", IEEE802.3af "Ethernet LAN/MAN Data terminal equipment power", and ETS300132-2 "Power supply interface at the input to telecommunications equipment; part 2: DC", but all of these standards are based on IEC/EN/UL60950 with regards to safety. 48 and 60 V DC systems If the input voltage to Ericsson AB DC/DC converter is 75 Vdc or less, then the output remains SELV (Safety Extra Low Voltage) under normal and abnormal operating conditions. Ericsson AB DC/DC converters and DC/DC regulators are UL60950 recognized and certified in accordance with EN60950. The flammability rating for all construction parts of the products meets requirements for V-0 class material according to IEC 60695-11-10. The products should be installed in the end-use equipment, in accordance with the requirements of the ultimate application. Normally the output of the DC/DC converter is considered as SELV (Safety Extra Low Voltage) and the input source must be isolated by minimum Double or Reinforced Insulation from the primary circuit (AC mains) in accordance with IEC/EN/UL60950. Single fault testing in the input power supply circuit should be performed with the DC/DC converter connected to demonstrate that the input voltage does not exceed 75 Vdc. If the input power source circuit is a DC power system, the source may be treated as a TNV2 circuit and testing has demonstrated compliance with SELV limits and isolation requirements equivalent to Basic Insulation in accordance with IEC/EN/UL60950. Non-isolated DC/DC regulators The input voltage to the DC/DC regulator is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions. Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) EPONMEL Approved PKU 4000B PI EAB/FJB/GKF(Natalie Johansson) 1 (5) No. 2/1301-BMR 654 02 Uen Checked Date Technical Specification Rev Reference See 1 2009-02-10 EN/LZT 146 376 R2A February 2009 B Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W 4 (c) Ericsson AB Absolute Maximum Ratings Characteristics min max Unit Tref Operating Temperature (see Thermal Consideration section) -40 typ +125 C TS Storage temperature -55 +125 C VI Input voltage -0.5 +80 V Viso Isolation voltage (input to output test voltage) 1500 Vdc Vtr Input voltage transient (tp 100 ms) 100 V VRC Remote Control pin voltage (see Operating Information section) 10 V -0.5 Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits of Output data or Electrical Characteristics. If exposed to stress above these limits, function and performance may degrade in an unspecified manner. Fundamental Circuit Diagram Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) 2 (5) No. EPONMEL 2/1301-BMR 654 02 Uen Approved PKU 4000B PI EAB/FJB/GKF(Natalie Johansson) Checked Date Technical Specification Rev Reference See 1 2009-02-10 EN/LZT 146 376 R2A February 2009 B Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W 5 (c) Ericsson AB 5 V, 20 A / 100 W Electrical Specification PKU 4101B PI Tref = -40 to +90C, VI = 36 to 75 V, unless otherwise specified under Conditions. Typical values given at: Tref = +25C, VI= 53 V, max IO, unless otherwise specified under Conditions. Cout = 2000 F, for details see note 1. Characteristics Conditions min typ Max Unit 75 V VI Input voltage range 36 VIoff Turn-off input voltage 29 30 32 V VIon Turn-on input voltage 30 32 35 V CI Internal input capacitance PO Output power Efficiency 3.3 0 F 100 50 % of max IO 93.1 max IO 91.9 50 % of max IO , VI = 48 V 93.4 max IO, VI = 48 V 91.8 W % Pd Power Dissipation max IO 8.5 Pli Input idling power IO = 0 A, VI = 53 V 1.8 W PRC Input standby power VI = 53 V (turned off with RC) 0.11 W fs Switching frequency 0-100 % of max IO 250 kHz VOi Output voltage initial setting and accuracy Tref = +25C, VI = 53 V, 50 % of max IO 4.8 Output voltage tolerance band 0-100 % of max IO 4.5 5.5 V Idling voltage IO = 0 A 5.0 5.5 V 5.0 11 5.2 W V Line regulation max IO 0.06 0.25 V Load regulation VI = 53 V, 0-100 % of max IO 0.4 0.6 V Vtr Load transient voltage deviation VI = 53 V, Load step 25-75-25 % of max IO, di/dt = 5 A/s. 40 mV ttr Load transient recovery time 80 s tr Ramp-up time ts tf tRC (from 10-90 % of VOi) Start-up time (from VI connection to 90 % of VOi) (from VI off to 10 % of VO) VI shut-down fall time max IO IO = 0 % of max IO RC start-up time 5 6 10 ms 15 18 21 ms max IO 1.5 22 16 ms RC shut-down fall time max IO 1.5 ms (from RC off to 10 % of VO) IO = 0 % of max IO 22 s 0 ms s IO Output current Ilim Current limit threshold Tref < max Tref 25 20 A Isc Short circuit current Tref = 25C, VO = 0.5V 32 A See ripple & noise section, 20 50 max IO, VOi Tref = +25C, VI = 53 V, 0-100 % of OVP Over voltage protection 6.2 max IO Note 1: Low ESR type (ESR approx 11 m). Minimum recommended capacitance for monotonic start up at 0 % load is 1000 F / 20 m. VOac Output ripple & noise A mVp-p V Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) 3 (5) No. EPONMEL 2/1301-BMR 654 02 Uen Approved PKU 4000B PI EAB/FJB/GKF(Natalie Johansson) Checked Date Technical Specification Rev Reference See 1 2009-02-10 EN/LZT 146 376 R2A February 2009 B Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W 6 (c) Ericsson AB 5 V, 20 A / 100 W Typical Characteristics PKU 4101B PI Efficiency Power Dissipation [%] [W] 12 95 90 36 V 85 9 36 V 48 V 53 V 80 48 V 6 53 V 75 V 75 V 3 75 70 0 4 8 12 16 0 20 [A] 0 4 8 12 16 20 [A] Dissipated power vs. load current and input voltage at Tref = +25C Efficiency vs. load current and input voltage at Tref = +25C Output Current Derating [A] 24 3.0 m/s 20 2.0 m/s 16 1.5 m/s 12 1.0 m/s 8 Nat. Conv. 4 0 20 40 60 80 100 [C] Available load current vs. ambient air temperature and airflow at VI = 53 V. See Thermal Consideration section. Output Characteristics Current Limit Characteristics [V] [V] 6 5.5 5 5.3 5.0 36 V 4 48 V 3 36 V 48 V 53 V 53 V 75 V 4.8 2 75 V 1 0 4.5 0 4 8 12 16 Output voltage vs. load current at Tref = +25C 20 [A] 12 16 20 24 28 32 36 [A] Output voltage vs. load current at IO > max IO , Tref = +25C Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) 4 (5) No. EPONMEL 2/1301-BMR 654 02 Uen Approved PKU 4000B PI EAB/FJB/GKF(Natalie Johansson) Checked Date Technical Specification Rev Reference See 1 2009-02-10 EN/LZT 146 376 R2A February 2009 B Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W (c) Ericsson AB 5 V, 20 A / 100 W Typical Characteristics Start-up Start-up enabled by connecting VI at: Tref = +25C, VI = 53 V, IO = 20 A. Output Ripple & Noise Output voltage ripple at: Tref = +25C, VI = 53 V, IO = 20 A. PKU 4101B PI Shut-down Top trace: output voltage (2 V/div.). Bottom trace: input voltage (50 V/div.). Time scale: (5 ms/div.). Shut-down enabled by disconnecting VI at: Tref = +25C, VI = 53 V, IO = 20 A resistive load. Top trace: output voltage (2 V/div.). Bottom trace: input voltage (50 V/div.). Time scale: (0.2 ms/div.). Output Load Transient Response Trace: output voltage (20 mV/div.). Time scale: (2 s/div.). 7 Output voltage response to load current step-change Top trace: output voltage (200 mV/div.). Tref =+25C, VI = 53 V. Bottom trace: load current (5 A/div.). Time scale: (0.1 ms/div.). Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) 1 (4) No. EPONMEL Approved PKU 4000B PI EAB/FJB/GMF (Natalie Johansson) 8 3/1301-BMR 654Technical 02 Uen Specification Checked Date Rev See 1 2009-02-04 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Reference EN/LZT 146 376 R2A February 2009 A (c) Ericsson AB EMC Specification Conducted EMI measured according to EN55022, CISPR 22 and FCC part 15J (see test set-up). See Design Note 009 for further information. The fundamental switching frequency is 250 kHz for PKU 4101B. Conducted EMI Input terminal value (typ) Test set-up Layout recommendation The radiated EMI performance of the DC/DC converter will depend on the PCB layout and ground layer design. It is also important to consider the stand-off of the DC/DC converter. With regards to the isolation requirements avoid placing a conductor which is connected to the primary side below the DC/DC converter. If a ground layer is used, it should be connected to the output of the DC/DC converter and the equipment ground or chassis. EMI without filter @ Vi = 48 V, max Io. External filter (class B) Required external input filter in order to meet class B in EN 55022, CISPR 22 and FCC part 15J. Filter components: C1, 2, 6 = 1 F/100 V Ceramic C3 L1 L2 C2 C1 C6 C4 Output ripple and noise Output ripple and noise measured according to figure below. See Design Note 022 for detailed information. C3, 4 = 2.2 nF/1500 V Ceramic DC/ DC C5 A ground layer will increase the stray capacitance in the PCB and improve the high frequency EMC performance. Load C5 = 100 F/50 V Electrolytic 50 mm +OUT Ceramic Capacitor L1,L2 = 1.47 mH 2.8 A, Common Mode 100 nF Tantalum Capacitor + 10 F -OUT Conductor from OUT to capacitors = 50 mm (1.97 in) Output ripple and noise test setup EMI with filter @ Vi = 48 V, max Io. BNC Connector to Scope LOAD Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) EPONMEL Approved PKU 4000B PI EAB/FJB/GMF (Natalie Johansson) 2 (4) No. 3/1301-BMR 654Technical 02 Uen Specification Checked Date See 1 2009-02-04 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Operating information Rev Reference 9 EN/LZT 146 376 R2A February 2009 A (c) Ericsson AB External Decoupling Capacitors Input Voltage The input voltage range 36 to 75 Vdc meets the requirements of the European Telecom Standard ETS 300 132-2 for normal input voltage range in -48 and -60 Vdc systems, -40.5 to 57.0 V and -50.0 to -72 V respectively. The absolute maximum continuous input voltage is 80 Vdc. Turn-off Input Voltage The DC/DC converters monitor the input voltage and will turn on and turn off at predetermined levels. The minimum hysteresis between turn on and turn off input voltage is 1 V. When powering loads with significant dynamic current requirements, the voltage regulation at the point of load can be improved by addition of decoupling capacitors at the load. The most effective technique is to locate low ESR ceramic and electrolytic capacitors as close to the load as possible, using several parallel capacitors to lower the effective ESR. The ceramic capacitors will handle high-frequency dynamic load changes while the electrolytic capacitors are used to handle low frequency dynamic load changes. Ceramic capacitors will also reduce any high frequency noise at the load. It is equally important to use low resistance and low inductance PCB layouts and cabling. For further information please contact your local Ericsson Power Modules representative. Remote Control (RC) The products are fitted with a remote control function referenced to the primary negative input connection (- In), with negative and positive logic options available. The RC function allows the converter to be turned on/off by an external device like a semiconductor or mechanical switch. The RC pin has an internal pull up resistor to + In. The maximum required sink current is 0.4 mA. When the RC pin is left open, the voltage generated on the RC pin is max 5 V. The maximum allowable leakage current of the switch is 50 A. With "negative logic" the converter will turn on when the input voltage is applied with the RC connected to the - In. Turn off is achieved by leaving the RC pin open, or connected to a voltage higher than 5 V referenced to -In. The second option is "positive logic" remote control, which can be ordered by adding the suffix "P" to the end of the part number. The converter will turn on when the input voltage is applied with the RC pin open. Turn off is achieved by connecting the RC pin to the - In. To ensure safe turn off the voltage difference between RC pin and the - In pin shall be less than 1 V. The converter will restart automatically when this connection is opened. Input and Output Impedance The impedance of both the input source and the load will interact with the impedance of the DC/DC converter. It is important that the input source has low characteristic impedance. The converters are designed for stable operation without external capacitors connected to the output. The performance in some applications can be enhanced by addition of external capacitance as described under External Decoupling Capacitors. If the input voltage source contains significant inductance, the addition of a 100 F capacitor across the input of the converter will ensure stable operation. The capacitor is not required when powering the DC/DC converter from an input source with an inductance below 10 H. Parallel Operation Two converters may be paralleled for redundancy (1+1) if the total power is equal or less than POmax for one unit. To secure the function o-ring diodes may be used. Pre-bias Start-up These products has pre-bias start up functionality and will not sink current during start up if a pre-bias source is present at the output terminal up to the min-value of output voltage tolerance band, i.e 4.5 V for a 5 V version and 10.8 V for a 12 V version. Nor will there be any under or over shoot. See Design Note 026 for detailed information. Over Temperature Protection (OTP) The converters are protected from thermal overload by an internal over temperature shutdown circuit. When Tref as defined in thermal consideration section exceeds 135C the converter will shut down. The DC/DC converter will resume normal operation automatically when the temperature has dropped approx 22C below the temperature threshold. Over Voltage Protection (OVP) The converters have output over voltage protection that will clamp the output voltage to a continous fixed level. After removal of the over voltage condition the converter will resume to normal operation automatically. Over Current Protection (OCP) The converters include current limiting circuitry for protection at continuous overload. The output voltage will decrease towards zero for output currents in excess of max output current (max IO). The DC/DC converter will resume normal operation after removal of the overload. The load distribution should be designed for the maximum output short circuit current specified. Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) EPONMEL Approved PKU 4000B PI EAB/FJB/GMF (Natalie Johansson) 3 (4) No. 3/1301-BMR 654Technical 02 Uen Specification Checked Date See 1 2009-02-04 Rev Reference EN/LZT 146 376 R2A February 2009 A Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W (c) Ericsson AB Connections Thermal Consideration General The converters are designed to operate in different thermal environments and sufficient cooling must be provided to ensure reliable operation. Cooling is achieved mainly by conduction, from the pins to the host board, and convection, which is dependent on the airflow across the converter. Increased airflow enhances the cooling of the converter. The Output Current Derating graph found in the Output section for each model provides the available output current vs. ambient air temperature and air velocity at Vin = 53 V. The DC/DC converter is tested on a 254 x 254 mm, 35 m (1 oz), 16-layer test board mounted vertically in a wind tunnel with a cross-section of 305 x 305 mm. Proper cooling of the DC/DC converter can be verified by measuring the temperature at reference point. The temperature at this position should not exceed the max values provided in the table below. See Design Note 019 for further information. Position Device Reference 4101B PI Designation Tref Max value 120C Reference Definition of reference temperature (Tref) The reference temperature is used to monitor the temperature limits of the product. Temperatures above maximum Tref are not allowed and may cause degradation or permanent damage to the product. Tref is also used to define the temperature range for normal operating conditions. Tref is defined by the design and used to guarantee safety margins, proper operation and high reliability of the module. Top View Pin 1 Designation +In Function Positive Input 2 RC Remote Control 3 -In Negative Input 4 -Out Negative Output 5 +Out Positive Output 10 Ericsson Internal PRODUCT SPEC. MECH. E Prepared (also subject responsible if other) EPANHON Approved PKU 4000B PI SEC/D [Julia You] 1 (3) No. 4/1301-BMR 654Technical Uen Specification Checked Date See 1 2009-02-10 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Mechanical Information- Surface mount version Rev Reference EN/LZT 146 376 R2A February 2009 C (c) Ericsson AB 11 Ericsson Internal PRODUCT SPEC. MECH. E Prepared (also subject responsible if other) EPANHON Approved PKU 4000B PI SEC/D [Julia You] 2 (3) No. 4/1301-BMR 654Technical Uen Specification Checked Date See 1 2009-02-10 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Mechanical Information- Hole mount version Rev Reference EN/LZT 146 376 R2A February 2009 C (c) Ericsson AB 12 Ericsson Internal PRODUCT SPEC.MECH. E Prepared (also subject responsible if other) 1 (4) No. 5/1301-BMR 654Technical Uen Specification EXXUYNG Approved PKU 4000B PI SEC/D [Betty Wu] Checked Date Rev See 1 2009-01-13 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Soldering Information - Surface Mounting The surface mount product is intended for forced convection or vapor phase reflow soldering in SnPb or Pb-free processes. The reflow profile should be optimised to avoid excessive heating of the product. It is recommended to have a sufficiently extended preheat time to ensure an even temperature across the host PCB and it is also recommended to minimize the time in reflow. A no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board, since cleaning residues may affect long time reliability and isolation voltage. Minimum Pin Temperature Recommendations Pin number 5 is chosen as reference location for the minimum pin temperature recommendation since this will likely be the coolest solder joint during the reflow process. Reference 13 EN/LZT 146 376 R2A February 2009 E (c) Ericsson AB Maximum Product Temperature Requirements Top of the product PCB near pin 2 is chosen as reference location for the maximum (peak) allowed product temperature (TPRODUCT) since this will likely be the warmest part of the product during the reflow process. SnPb solder processes For SnPb solder processes, the product is qualified for MSL 1 according to IPC/JEDEC standard J-STD-020C. During reflow TPRODUCT must not exceed 225 C at any time. Pb-free solder processes For Pb-free solder processes, the product is qualified for MSL 3 according to IPC/JEDEC standard J-STD-020C. During reflow TPRODUCT must not exceed 260 C at any time. Dry Pack Information Products intended for Pb-free reflow soldering processes are SnPb solder processes For SnPb solder processes, a pin temperature (TPIN) in excess delivered in standard moisture barrier bags according to of the solder melting temperature, (TL, 183C for Sn63Pb37) for IPC/JEDEC standard J-STD-033 (Handling, packing, shipping and use of moisture/reflow sensitivity surface mount devices). more than 30 seconds and a peak temperature of 210C is recommended to ensure a reliable solder joint. Using products in high temperature Pb-free soldering processes requires dry pack storage and handling. In case the Lead-free (Pb-free) solder processes products have been stored in an uncontrolled environment and For Pb-free solder processes, a pin temperature (TPIN) in excess of the solder melting temperature (TL, 217 to 221C for no longer can be considered dry, the modules must be baked according to J-STD-033. SnAgCu solder alloys) for more than 30 seconds and a peak temperature of 235C on all solder joints is recommended to ensure a reliable solder joint. Thermocoupler Attachment Pin 5 for measurement of minimum pin (solder joint) temperature, TPIN General reflow process specifications SnPb eutectic Pb-free Average ramp-up (TPRODUCT) 3C/s max 3C/s max 183C 221C Typical solder melting (liquidus) temperature TL Minimum reflow time above TL Minimum pin temperature TPIN Peak product temperature TPRODUCT 30 s 30 s 210C 235C 225C 260C Average ramp-down (TPRODUCT) 6C/s max 6C/s max Maximum time 25C to peak 6 minutes 8 minutes Temperature Pin 2 for measurement of maximum product temperature, TPRODUCT TPRODUCT maximum TPIN minimum Pin profile TL Product profile Time in reflow Time in preheat / soak zone Time 25C to peak Time Ericsson Internal PRODUCT SPEC.MECH. E Prepared (also subject responsible if other) 2 (4) No. 5/1301-BMR 654Technical Uen Specification EXXUYNG Approved PKU 4000B PI SEC/D [Betty Wu] Checked Date See 1 2009-01-13 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Rev Reference EN/LZT 146 376 R2A February 2009 E (c) Ericsson AB Soldering Information - Hole Mounting Tray Specifications The hole mounted product is intended for plated through hole mounting by wave or manual soldering. The pin temperature is specified to maximum 270C for maximum 10 seconds. Material Antistatic PPE Surface resistance Tray thickness 10 < Ohm/square < 10 The trays can be baked at maximum 125C for 48 hours] 18.5 mm [0.728 inch] Box capacity 150 products (5 full trays/box) Tray weight 190 g empty, 600 g full tray Bakability A maximum preheat rate of 4C/s and maximum preheat temperature of 150C is suggested. When soldering by hand, care should be taken to avoid direct contact between the hot soldering iron tip and the pins for more than a few seconds in order to prevent overheating. 14 5 12 A no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board. The cleaning residues may affect long time reliability and isolation voltage. Delivery Package Information The surface mount products are delivered in antistatic injection molded trays (Jedec design guide 4.10D standard) and in antistatic carrier tape (EIA 481 standard). The through-hole mount products are delivered in antistatic injection molded trays (Jedec design guide 4.10D standard). Carrier Tape Specifications Material Antistatic PS Surface resistance < 10 Ohm/square Bakeability The tape is not bakable 7 Tape width, W 56 mm [2.2 inch] Pocket pitch, P1 36 mm [1.42 inch] Pocket depth, K0 8.7 mm [0.343 inch] Reel diameter 380 mm [15 inch] Reel capacity 200 products /reel Reel weight Rounded 3 kg/full reel EIA standard carrier tape Side view User tape feed direction Round holes Tape width, W Top view Pocket depth, K0 Pin 1 Elongated holes Pocket pitch, P1 X= Vacuum pickup area All dimensions in mm [inch] Tolerances: X.xx mm 0.13 mm [0.005], X.x mm 0.26 mm [0.01] Note: tray dimensions refer to pocket center. For exact location of product pick up surface, refer to mechanical drawing. Ericsson Internal PRODUCT SPEC.MECH. E Prepared (also subject responsible if other) 3 (4) No. 5/1301-BMR 654Technical Uen Specification EXXUYNG Approved PKU 4000B PI SEC/D [Betty Wu] Checked Date See 1 2009-01-13 Intermediate Bus Converters, Input 36-75 V, 20 A / 100 W Rev Reference EN/LZT 146 376 R2A February 2009 E (c) Ericsson AB Product Qualification Specification Characteristics External visual inspection IPC-A-610 Change of temperature (Temperature cycling) IEC 60068-2-14 Na Temperature range Number of cycles Dwell/transfer time -40 to 100C 1000 15 min/0-1 min Cold (in operation) IEC 60068-2-1 Ad Temperature TA Duration -45C 72 h Damp heat IEC 60068-2-67 Cy Temperature Humidity Duration 85C 85 % RH 1000 hours Dry heat IEC 60068-2-2 Bd Temperature Duration 125C 1000 h Electrostatic discharge susceptibility IEC 61340-3-1, JESD 22-A114 IEC 61340-3-2, JESD 22-A115 Human body model (HBM) Machine Model (MM) Class 2, 2000 V Class 3, 200 V Immersion in cleaning solvents IEC 60068-2-45 XA, method 2 Water Glycol ether Isopropyl alcohol 55C 35C 35C Mechanical shock IEC 60068-2-27 Ea Peak acceleration Duration 100 g 6 ms J-STD-020C Level 1 (SnPb-eutectic) Level 3 (Pb Free) 225C 260C MIL-STD-202G, method 108A Duration 1000 h IEC 60068-2-20 Tb, method 1A Solder temperature Duration 270C 10-13 s IEC 60068-2-21 Test Ua1 IEC 60068-2-21 Test Ue1 Through hole mount products Surface mount products All leads All leads Preconditioning Temperature, SnPb Eutectic Temperature, Pb-free 150C dry bake 16 h 215C 235C Preconditioning Temperature, SnPb Eutectic Temperature, Pb-free Steam ageing 235C 245C Frequency Spectral density Duration 10 to 500 Hz 2 0.07 g /Hz 10 min in each direction Moisture reflow sensitivity 1 Operational life test Resistance to soldering heat 2 Robustness of terminations IEC 60068-2-58 test Td 1 IEC 60068-2-20 test Ta 2 Solderability Vibration, broad band random IEC 60068-2-64 Fh, method 1 Notes 1 Only for products intended for reflow soldering (surface mount products) 2 Only for products intended for wave soldering (plated through hole products) 15