©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63004

MULTILAYER CERAMIC CAPACITORS/AXIAL

&RADIAL LEADED

Multilayer ceramic capacitors are available in a

variety of physical sizes and configurations, including

leaded devices and surface mounted chips. Leaded

styles include molded and conformally coated parts

with axial and radial leads. However, the basic

capacitor element is similar for all styles. It is called a

chip and consists of formulated dielectric materials

which have been cast into thin layers, interspersed

with metal electrodes alternately exposed on opposite

edges of the laminated structure.

The entire structure is

fired at high temperature to produce a monolithic

block

which provides high capacitance values in a

small physical volume. After firing, conductive

terminations are applied to opposite ends of the chip to

make contact with the exposed electrodes.

Termination materials and methods vary depending on

the intended use.

TEMPERATURE CHARACTERISTICS

Ceramic dielectric materials can be formulated with

awide range of characteristics. The EIA standard for

ceramic dielectric capacitors (RS-198) divides ceramic

dielectrics into the following classes:

Class I: Temperature compensating capacitors,

suitable for resonant circuit application or other appli-

cations where high Q and stability of capacitance char-

acteristics are required. Class I capacitors have

predictable temperature coefficients and are not

affected by voltage, frequency or time. They are made

from materials which are not ferro-electric, yielding

superior stability but low volumetric efficiency.Class I

capacitors are the most stable type available, but have

the lowest volumetric efficiency.

Class II: Stable capacitors, suitable for bypass

or coupling applications or frequency discriminating

circuits where Q and stability of capacitance char-

acteristics arenot of major importance. Class II

capacitors have temperature characteristics of ± 15%

or less. They aremade from materials which are

ferro-electric, yielding higher volumetric efficiency but

less stability. Class II capacitors are affected by

temperature, voltage, frequency and time.

Class III: General purpose capacitors, suitable

for by-pass coupling or other applications in which

dielectric losses, high insulation resistance and

stability of capacitance characteristics are of little or

no importance. Class III capacitors are similar to Class

II capacitors except for temperature characteristics,

which are greater than ± 15%. Class III capacitors

have the highest vol

umetric efficiency and poorest

stability of any type.

KEMET leaded ceramic capacitors are offered in

the three most popular temperature characteristics:

C0G: Class I, with a temperature coefficient of 0 ±

30 ppm per degree C over an operating

temperature range of - 55°C to + 125°C (Also

known as “NP0”).

X7R: Class II, with a maximum capacitance

change of ± 15% over an operating temperature

range of - 55°Cto + 125°C.

Z5U: Class III, with a maximum capacitance

change of + 22% - 56% over an operating tem-

peraturerange of + 10°Cto + 85°C.

Specified electrical limits for these three temperature

characteristics areshown in Table 1.

SPECIFIED ELECTRICAL LIMITS

Table I

C0G X7R Z5U

Dissipation Factor: Measured at following conditions.

C0G – 1 kHz and 1 vrms if capacitance >1000pF

1 MHz and 1 vrms if capacitance 1000 pF

X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms

Z5U – 1 kHz and 0.5 vrms

0.10%

2.5%

(3.5% @ 25V)

4.0%

Dielectric Stength: 2.5 times rated DC voltage.

Insulation Resistance (IR): At rated DC voltage,

whichever of the two is smaller

1,000 M F

or 100 G

1,000 M F

or 100 G

1,000 M F

or 10 G

Temperature Characteristics: Range, °C

Capacitance Change without

DC voltage

-55 to +125

0 ± 30 ppm/°C

-55 to +125

± 15%

+ 10 to +85

+22%,-56%

* MHz and 1 vrms if capacitance 100 pF on military product.

Parameter

Temperature Characteristics

Pass Subsequent IR Test

ELECTRICAL CHARACTERISTICS

The fundamental electrical properties of multilayer

ceramic capacitors are as follows:

Polarity: Multilayer ceramic capacitors are not polar,

and may be used with DC voltage applied in either direction.

Rated Voltage: This term refers to the maximum con-

tinuous DC working voltage permissible across the entire

operating temperature range. Multilayer ceramic capacitors

are not extremely sensitive to voltage, and brief applications

of voltage above rated will not result in immediate failure.

However, reliability will be reduced by exposure to sustained

voltages above rated.

Capacitance:

The standard unit of capacitance is the

farad. For practical capacitors, it is usually expressed in

microfarads (10-6 farad), nanofarads (10-9 farad), or picofarads

(10-12 farad). Standard measurement conditions are as

follows:

Class I (up to 1,000 pF): 1MHz and 1.2 VRMS

maximum.

Class I (over 1,000 pF): 1kHz and 1.2 VRMS

maximum.

Class II: 1 kHz and 1.0 ± 0.2 VRMS.

Class III: 1 kHz and 0.5 ± 0.1 VRMS.

Like all other practical capacitors, multilayer ceramic

capacitors also have resistance and inductance. A simplified

schematic for the equivalent circuit is shown in Figure 1.

Other significant electrical characteristics resulting from

these additional properties are as follows:

Impedance: Since the parallel resistance (Rp) is nor-

mally very high, the total impedance of the capacitor is:

Figure 1

C = Capacitance

L = Inductance

RS=Equivalent Series Resistance (ESR)

RP=Insulation Resistance (IR)

RP

RS

C

L

Z =

Where Z = Total Impedance

RS = Equivalent Series Resistance

X

C

=Capacitive Reactance =

2ππfC

X

L

=Inductive Reactance = 2ππfL

1

R

S

+(X

C

- X

L

)

22

DF = ESR

Xc

Xc2πfC

1

=

Figure 2

δ

Ζ

O

Xc

ESR

The variation of a capacitor’s impedance with frequency

determines its effectiveness in many applications.

Dissipation Factor: Dissipation Factor (DF) is a mea-

sure of the losses in a capacitor under AC application. It is the

ratio of the equivalent series resistance to the capacitive reac-

tance

,and is usually expressed in percent. It is usually mea-

sured simultaneously with capacitance, and under the same

conditions. The vector diagram in Figure 2 illustrates the rela-

tionship between DF, ESR, and impedance. The reciprocal of

the dissipation factor is called the “Q”, or quality factor. For

convenience, the “Q” factor is often used for very low values

of dissipation factor. DF is sometimes called the “loss tangent”

or “tangent d”, as derived from this diagram.

Insulation Resistance: Insulation Resistance (IR) is the

DC resistance measured across the terminals of a capacitor,

represented by the parallel resistance (Rp) shown in Figure 1.

For a given dielectric type, electrode area increases with

capacitance, resulting in a decrease in the insulation resis-

tance. Consequently, insulation resistance is usually specified

as the “RC” (IR x C) product, in terms of ohm-farads or

megohm-microfarads. The insulation resistance for a specific

capacitance value is determined by dividing this product by

the capacitance. However, as the nominal capacitance values

become small, the insulation resistance calculated from the

RC product reaches values which are impractical.

Consequently, IR specifications usually include both a mini-

mum RC product and a maximum limit on the IR calculated

from that value. For example, a typical IR specification might

read “1,000 megohm-microfarads or 100 gigohms, whichever

is less.”

Insulation Resistance is the measure of a capacitor to

resist the flow of DC leakage current. It is sometimes referred

to as “leakage resistance.” The DC leakage current may be

calculated by dividing the applied voltage by the insulation

resistance (Ohm’s Law).

Dielectric Withstanding Voltage: Dielectric withstand-

ing voltage (DWV) is the peak voltage which a capacitor is

designed to withstand for short periods of time without dam-

age. All KEMET multilayer ceramic capacitors will withstand a

test voltage of 2.5 x the rated voltage for 60 seconds.

KEMET specification limits for these characteristics at

standard measurement conditions are shown in Table 1 on

page 4. Variations in these properties caused by changing

conditions of temperature, voltage, frequency, and time are

covered in the following sections.

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 5

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

Application Notes

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63006

TABLE 1

EIA TEMPERATURE CHARACTERISTIC CODES

FOR CLASS I DIELECTRICS

Significant Figure Multiplier Applied Tolerance of

of Temperature to Temperature Temperature

Coefficient Coefficient Coefficient *

PPM per Letter Multi- Number PPM per Letter

Degree C Symbol plier Symbol Degree C Symbol

0.0 C -1 0 ±30 G

0.3 B -10 1 ±60 H

0.9 A -100 2 ±120 J

1.0 M -1000 3 ±250 K

1.5 P -100000 4 ±500 L

2.2 R +1 5 ±1000 M

3.3 S +10 6 ±2500 N

4.7 T +100 7

7.5 U +1000 8

+10000 9

*These symetrical tolerances apply to a two-point measurement of

temperature coefficient: one at 25°C and one at 85°C. Some deviation

is permitted at lower temperatures. For example, the PPM tolerance

for C0G at -55°C is +30 / -72 PPM.

TABLE 2

EIA TEMPERATURE CHARACTERISTIC CODES

FOR CLASS II & III DIELECTRICS

Low Temperature High Temperature Maximum Capacitance

Rating Rating Shift

Degree Letter Degree Number Letter

Celcius Symbol Celcius Symbol Percent Symbol

+10C Z +45C 2 ±1.0% A

-30C Y +65C 4 ±1.5% B

-55C X +85C 5 ±2.2% C

+105C 6 ±3.3% D

+125C 7 ±4.7% E

+150C 8 ±7.5% F

+200C 9 ±10.0% P

±15.0% R

±22.0% S

+22/-33% T

+22/-56% U

+22/-82% V

+10 +20 +30 +40 +50 +60 +70 +80

Effect of Temperature: Both capacitance and dissipa-

tion factor are affected by variations in temperature. The max-

imum capacitance change with temperatureis defined by the

temperaturecharacteristic. However,this only defines a “box”

bounded by the upper and lower operating temperatures and

the minimum and maximum capacitance values. Within this

“box”, the variation with temperature depends upon the spe-

cific dielectric formulation. Typical curves for KEMET capaci-

tors are shown in Figures 3, 4, and 5. These figures also

include the typical change in dissipation factor for KEMET

capacitors.

Insulation resistance decreases with temperature.

Typically, the insulation resistance at maximum rated temper-

atureis 10% of the 25°Cvalue.

Effect of Voltage: Class I ceramic capacitors arenot

affected by variations in applied AC or DC voltages. For Class

II and III ceramic capacitors, variations in voltage affect only

the capacitance and dissipation factor.The application of DC

voltage higher than 5 vdc reduces both the capacitance and

dissipation factor. The application of AC voltages up to 10-20

Vac tends to increase both capacitance and dissipation factor.

At higher AC voltages, both capacitance and dissipation factor

begin to decrease.

Typical curves showing the effect of applied AC and DC

voltage are shown in Figure 6 for KEMET X7R capacitors and

Figure 7 for KEMET Z5U capacitors.

Effect of Frequency: Frequency affects both capaci-

tance and dissipation factor. Typical curves for KEMET multi-

layer ceramic capacitors are shown in Figures 8 and 9.

T

he variation of impedance with frequency is an impor-

tant consideration in the application of multilayer ceramic

capacitors. Total impedance of the capacitor is the vector of the

capacitive reactance, the inductive reactance, and the ESR, as

illustrated in Figure 2. As frequency increases, the capacitive

reactance decreases. However, the series inductance (L)

shown in Figure 1 produces inductive reactance, which

increases with frequency. At some frequency, the impedance

ceases to be capacitive and becomes inductive. This point, at

the bottom of the V-shaped impedance versus frequency

curves, is the self-resonant frequency. At the self-resonant fre-

quency, the reactance is zero, and the impedance consists of

the ESR only.

Typical impedance versus frequency curves for KEMET

multilayer ceramic capacitors areshown in Figures 10, 11, and

12. These curves apply to KEMET capacitors in chip form, with-

out leads. Lead configuration and lead length have a significant

impact on the series inductance. The lead inductance is

approximately 10nH/inch, which is large compared to the

inductance of the chip. The effect of this additional inductance

is a decrease in the self-resonant frequency,and an increase

in impedance in the inductive region above the self-resonant

frequency.

Effect of Time: The capacitance of Class II and III

dielectrics change with time as well as with temperature, volt-

age and frequency. This change with time is known as “aging.”

It is caused by gradual realignment of the crystalline structure

of the ceramic dielectric material as it is cooled below its Curie

temperature, which produces a loss of capacitance with time.

The aging process is predictable and follows a logarithmic

decay.Typical aging rates for C0G, X7R, and Z5U dielectrics

areas follows:

C0G None

X7R 2.0% per decade of time

Z5U 5.0% per decade of time

Typical aging curves for X7R and Z5U dielectrics are

shown in Figure 13.

The aging process is reversible. If the capacitor is heat-

ed to a temperature above its Curie point for some period of

time, de-aging will occur and the capacitor will regain the

capacitance lost during the aging process. The amount of de-

aging depends on both the elevated temperatureand the

length of time at that temperature. Exposure to 150°C for one-

half hour or 125°C for two hours is usually sufficient to return

the capacitor to its initial value.

Because the capacitance changes rapidly immediately

after de-aging, capacitance measurements are usually delayed

for at least 10 hours after the de-aging process, which is often

referred to as the “last heat.” In addition, manufacturers utilize

the aging rates to set factory test limits which will bring the

capacitance within the specified tolerance at some futuretime,

to allow for customer receipt and use. Typically, the test limits

areadjusted so that the capacitance will be within the specified

tolerance after either 1,000 hours or 100 days, depending on

the manufacturer and the product type.

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 7

Application Notes

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63008

POWER DISSIPATION

Power dissipation has been empirically determined for

two representative KEMET series: C052 and C062. Power dis-

sipation capability for various mounting configurations is shown

in Table 3. This table was extracted from Engineering Bulletin

F-2013, which provides a more detailed treatment of this sub-

ject.

Note that no significant difference was detected between

the two sizes in spite of a 2 to 1 surface area ratio. Due to the

materials used in the construction of multilayer ceramic capac-

itors, the power dissipation capability does not depend greatly

on the surface area of the capacitor body, but rather on how

well heat is conducted out of the capacitor lead wires.

Consequently, this power dissipation capability is applicable to

other leaded multilayer styles and sizes.

TABLE 3

POWER DISSIPATION CAPABILITY

(Rise in Celsius degrees per Watt)

Power

Mounting Configuration Dissipation

of C052 & C062

1.00" leadwires attached to binding post 90 Celsius degrees

of GR-1615 bridge (excellent heat sink) rise per Watt ±10%

0.25" leadwires attached to binding post 55 Celsius degrees

of GR-1615 bridge rise per Watt ±10%

Capacitor mounted flush to 0.062" glass- 77 Celsius degrees

epoxy circuit board with small copper traces rise per Watt ±10%

Capacitor mounted flush to 0.062" glass- 53 Celsius degrees

epoxy circuit board with four square inches rise per Watt ±10%

of copper land area as a heat sink

As shown in Table 3, the power dissipation capability of

the capacitor is very sensitive to the details of its use environ-

ment. The temperature rise due to power dissipation should not

exceed 20°C. Using that constraint, the maximum permissible

power dissipation may be calculated from the data provided in

Table 3.

It is often convenient to translate power dissipation capa-

bility into a permissible AC voltage rating. Assuming a sinu-

soidal wave form, the RMS “ripple voltage” may be calculated

The data necessary to make this calculation is included in

Engineering Bulletin F-2013. However,the following criteria

must be observed:

1. The temperature rise due to power dissipation

should be limited to 20°C.

2. The peak AC voltage plus the DC voltage must not

exceed the maximum working voltage of the

capacitor.

Provided that these criteria aremet, multilayer ceramic

E=Zx

Where E = RMS Ripple Voltage (volts)

P = Power Dissipation (watts)

Z = Impedance

R = ESR

P

MAX

R

capacitors may be operated with AC voltage applied without

need for DC bias.

RELIABILITY

Awell constructed multilayer ceramic capacitor is

extremely reliable and, for all practical purposes, has an infi-

nite life span when used within the maximum voltage and

temperature ratings. Capacitor failure may be induced by sus-

tained operation at voltages that exceed the rated DC voltage,

voltage spikes or transients that exceed the dielectric with-

standing voltage, sustained operation at temperatures above

the maximum rated temperature, or the excessive tempera-

ture rise due to power dissipation.

Failure rate is usually expressed in terms of percent per

1,000 hours or in FITS (failure per billion hours). Some

KEMET series are qualified under U.S. military established

reliability specifications MIL-PRF-20, MIL-PRF-123, MIL-

PRF-39014, and MIL-PRF-55681. Failure rates as low as

0.001% per 1,000 hours are available for all capacitance /

voltage ratings covered by these specifications. These spec-

ifications and

accompanying Qualified Products List should

be consulted for details.

For series not covered by these military specifications,

an internal testing program is maintained by KEMET Quality

Assurance. Samples from each week’s production are sub-

jected to a 2,000 hour accelerated life test at 2 x rated voltage

and maximum rated temperature. Based on the results of

these tests, the average failure rate for all non-military series

covered by this test program is currently 0.06% per 1,000

hours at maximum rated conditions. The failure rate would be

much lower at typical use conditions. For example, using MIL-

HDBK-217D this failure rate translates to 0.9 FITS at 50%

rated voltage and 50°C.

Current failure rate details for specific KEMET multilay-

er ceramic capacitor series areavailable on request.

MISAPPLICATION

Ceramic capacitors, like any other capacitors, may fail

if they aremisapplied. Typical misapplications include expo-

sure to excessive voltage, current or temperature. If the

dielectric layer of the capacitor is damaged by misapplication

the electrical energy of the circuit can be released as heat,

which may damage the circuit board and other components

as well.

If potential for misapplication exists, it is recommended

that precautions be taken to protect personnel and equipment

during initial application of voltage. Commonly used precau-

tions include shielding of personnel and sensing for excessive

power drain during board testing.

STORAGE AND HANDLING

Ceramic chip capacitors should be stored in normal

working environments. While the chips themselves are quite

robust in other environments, solderability will be degraded

by exposureto high temperatures, high humidity, corrosive

atmospheres, and long term storage. In addition, packaging

materials will be degraded by high temperature–reels may

soften or warp, and tape peel force may increase. KEMET

recommends that maximum storage temperature not exceed

40˚ C, and maximum storage humidity not exceed 70% rela-

tive humidity. In addition, temperature fluctuations should be

minimized to avoid condensation on the parts, and atmos-

pheres should be free of chlorine and sulfur bearing com-

pounds. For optimized solderability, chip stock should be

used promptly, preferably within 1.5 years of receipt.

from the following formula:

IMPEDANCE VS FREQUENCY

Impedance (Ohms)

110100 1,000

0.001

0.01

1

10

100

0.1

0.1

Frequency - MHz

Impedance vs Frequency for C0G Dielectric

Figure 10.

EFFECT OF FREQUENCY

-0.1

0

+0.2

-0.2

+0.1

0.10

0.20

0.0

Frequency - Hertz

Capacitance & DF vs Frequency - C0G

Figure 8.

%DF

Typical Aging Rates for X7R & Z5UFigure 13.

74%

76%

78%

80%

82%

84%

86%

88%

90%

92%

94%

96%

98%

100%

Capacitance

110100 1000 10K 100K

EFFECT OF TIME

%DF

-10

-5

+5

-15

0

5.0

10.0

0.0

2.5

7.5

Frequency - Hertz

Capacitance & DF vs Frequency - X7R & Z5U

Figure 9.

.01μF.001μF

%ΔC

1001K 10K 100K1M 10M

1001K 10K 100K1M 10M

%ΔC

%ΔC

%DF

Z5U

X7R

%DF

%ΔC

Impedance (Ohms)

110100 1,000

0.001

0.01

1

10

100

0.1

0.1

Frequency - MHz

Impedance vs Frequency for Z5U Dielectric

Figure 12.

Impedance (Ohms)

110100 1,000

0.001

0.01

1

10

100

0.1

0.1

Frequency - MHz

Impedance vs Frequency for X7R Dielectric

Figure 11.

0.1μF

1.0 μF

0.1μF.01μF

1.0 μF

Impedance vs. Frequency

Leaded Ceramic C0G

0.01

0.1

1

10

100

0.1 1 1 0100 1000

Frequency - MHz

Impedance (Ohms)

0.01µF

0.001µF

Leaded X7R

0.01

0.1

1

10

100

0.1 1 1 0100 1000

Frequency - MHz

Impedance (Ohms)

0.01µF

0.1µF

Impedance vs. Frequency

1.0µF

Impedance vs. Frequency

Leaded Z5U

0.01

0.1

1

10

100

0.1 1 1 0100 1000

Frequency - MHz

Impedance (Ohms)

0.1µF

1.0µF

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Capacitance

100%

74%

76%

78%

80%

82%

84%

86%

88%

90%

92%

94%

96%

98%

X7R

Z5U

1 10 100 1000 10K 100K

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 9

Application Notes

APPLICATION NOTES FOR MULTILAYER

CERAMIC CAPACITORS

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

Impedance vs Frequency

for C0G Dielectric

Figure 10.

Impedance vs Frequency

for Z5U Dielectric

Figure 12.

Impedance vs Frequency

for X7R Dielectric

Figure 11.

(hours)

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 27

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

Ceramic Molded

Axial/Radial - Standard

GENERAL SPECIFICATIONS

Working Voltage:

C0G – 50, 100, 200

X7R – 50, 100, 200

Temperature Characteristics:

C0G 0 ±30 PPM / °C from -55°C to +125°C

X7R ± 15% from -55°C to +125°C

Capacitance Tolerance:

C0G ±0.5pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5pF is tightest tolerance available)

X7R ±10%, ±20%, -0 +100%, +80% / -20%

Construction:

Monolithic block of ceramic dielectric with

Interdigitated internal electrodes, encapsulated

in a molded case,and having axial or radial leads.

Meets flame testrequirements ofUL Standard 94V-0.

Lead Material:

Axial: Solder coated copper clad steel

Radial: Solder-coated copper standard (100% tin

plated optional)

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for

5 ±1/2 seconds.

Terminal Strength:

EIA-198 Method 303, Condition A (2.2 kg)

ELECTRICAL

Capacitance:

Within specified tolerance and when measured with

1 volt rms at 1kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor @25°C:

25°C at 1kHz (1000 pF or less at 1 MHz for C0G).

C0G – 0.15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K M or 1000 M – F, whichever is less.

X7R – 100K M or 1000 M – F, whichever is less.

Dielectric Withstanding Voltage:

250% ofrated voltage for 5 seconds with current limited

to 50 mA at 25°C.

MIL-STD-202, Method 208, Sn62 solder, 245 C for

5 ±1/2 seconds.

Terminal Strength:

EIA-198 Method 303, Condition A (2.2 kg)

ELECTRICAL

Capacitance:

Within specified tolerance and when measured with

1 volt rms at 1kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor @25°C:

25°C at 1kHz (1000 pF or less at 1 MHz for C0G).

C0G – 0.15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K M or 1000 M – F, whichever is less.

X7R – 100K M or 1000 M – F, whichever is less.

Dielectric Withstanding Voltage:

250% ofrated voltage for 5 seconds with current limited

to 50 mA at 25°C.

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630028

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Lead Dia.

.025

(+.004

-.002)

S

H

1.25

Min.

W

Center Line of leads

within .030" of Center

Line of case.

H

1.25

Min.

L

S

W

.045

Max.

L

CAPACITOR OUTLINE DRAWINGS - (RADIAL LEADS)

C052 C062,

C512,

C522

Lead Dia.

.025

(+.004

-.002)

DIMENSIONS — INCHES (MILLIMETERS)

DL

C

1.50 Min.

(38.10)

1.50 Min.

(38.10)

CAPACITOR OUTLINE DRAWINGS - (AXIAL LEADS)

CAPACITOR OUTLINE DRAWINGS — (AXIAL LEADS)

CAPACITOR OUTLINE DRAWINGS — (RADIAL LEADS)

DIMENSIONS — INCHES (MILLIMETERS)

For packaging information, see pages 46, 47 and 48.

Case

Size

Military

Equivalent Styles

H

Height

L

Length

W

Width

S

Lead

Spacing

C052 CC05, CCR05

CK05, CKR05 .190 ± .010 (4.83 ± .25) .190 ± .010 (4.83 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)

C062 CC06, CCR06

CK06, CKR06 .290 ± .010 (7.37 ± .25) .290 ± .010 (7.37 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)

C512 CC07, CCR07 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .140 ± .010 (3.56 ± .25) .400 ± .020 (10.16 ± .51)

C522 CC08, CCR08 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .240 ± .010 (6.10 ± .25) .400 ± .020 (10.16 ± .51)

Case

Size

Military

Equivalent Styles

L

Length

D

Body diameter

C

Lead Diameter

C114

CC75, CCR75

CK12, CKR11

.160 ± .010 (4.06 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)

C124

CC76, CCR76

CK13, CKR12

.250 ± .010 (6.35 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)

C192

CC77, CCR77

CK14, CKR14

.390 ± .010 (9.91 ± .25) .140 ± .010 (3.56 ± .25) .025, +.004, -.001 (.64, +.10, -.025)

C202

CC78, CCR78

CK15, CKR15

.500 ± .020 (12.70 ± .51) .250 ± .015 (6.35 ± .38) .025, +.004, -.001 (.64, +.10, -.025)

C222

CC79, CCR79

CK16, CKR16

.690 ± .030 (17.53 ± .76) .350 ± .020 (8.89 ± .51) .025, +.004, -.001 (.64, +.10, -.025)

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 29

ORDERING INFORMATION

AXIAL CAPACITOR MARKING

STANDARD C114C, C124C, C192C, C202C & C222C

KC0G

101J

200V

0812

KEMET,Temperature Characteristic

Capacitance, Capacitance Tolerance

Voltage

Date Code

RADIAL CAPACITOR MARKING

C052C & C062C STANDARD MARKING

100V

K

0811

Voltage

KEMET

Date Code

BACK

C062

X7R

104K

FRONT

Style

Temperature Characteristic

Capacitance, Capacitance Tolerance

C512 & C522 STANDARD MARKING

KEMET

C512X7R

105K 50V

0832

KEMET

SIZE and Temperature Characteristic

Capacitance, Capacitance Tolerance, Voltage

Date Code

Ceramic Molded

Axial/Radial - Standard

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

C052 C 102 K 2 R 5 T A

CERAMIC

CASE SIZE

See Table Below

SPECIFICATION

C – Standard

CAPACITANCE PICOFARAD CODE

Expressed in picofarads (pF). First two digits represent

significant figures. Third digit specifies number of zeros

following except 9 indicates division by 10). Examples:

0.1 µF = 100,000 pF = 104 and 9.1 pF = 919. See

tables for standard values.

CAPACITANCE TOLERANCE

Standard Others

M–±20% H – ±3%

K – ±10% G – ±2%

J – ±5% F – ±1%

D–±.5pF WORKING VOLTAGE (DC)

2–200V; 1 – 100V; 5 – 50V

FAILURE RATE

A – Not Applicable

LEAD MATERIAL

C–60/40 Tin/Lead (SnPb)

T – 100% Tin (Sn)(C052,

C062 only)

INTERNAL CONSTRUCTION

5 – Multilayer

TEMPERATURE CHARACTERISTIC

KEMET

Designator

EIA

Equivalent

Cap. Change with Temp.

Temp

Range, °C

Measured

without DC

Bias Voltage

G

(Ultra Stable)

C0G

(NP0)

-55 to

+125°

±30

ppm/°C

R

(Stable) X7R -55° to

+125 ±15%

Standard tolerances for each Series

are shown in the repetitive parts lists.

Case Sizes

Radial Axial

C052 C114

C062 C124

C512 C192

C522 C202

C222

Part Number Example: C052C102K2R5TA (14 digits – no spaces)

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630030

CERAMIC MOLDED/RADIAL – STANDARD

ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)

RATINGS & PART NUMBER REFERENCE

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF

(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%

(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%

(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

CAPACITANCE

pF

KEMET

PART NUMBER

1.0 C114C109(1)2G5CA

1.5 C114C159(1)2G5CA

2.2 C114C229(1)2G5CA

2.7 C114C279(1)2G5CA

3.3 C114C339(1)2G5CA

3.9 C114C399(1)2G5CA

4.7 C114C479(1)2G5CA

5.6 C114C569(1)2G5CA

6.8 C114C689(1)2G5CA

8.2 C114C829(1)2G5CA

10.0 C114C100(2)2G5CA

12.0 C114C120(2)2G5CA

15.0 C114C150(2)2G5CA

18.0 C114C180(2)2G5CA

22.0 C114C220(2)2G5CA

27.0 C114C270(3)2G5CA

33.0 C114C330(3)2G5CA

39.0 C114C390(3)2G5CA

47.0 C114C470(3)2G5CA

56.0 C114C560(4)2G5CA

68.0 C114C680(4)2G5CA

82.0 C114C820(4)2G5CA

100.0 C114C101(4)2G5CA

120.0 C114C121(4)2G5CA

150.0 C114C151(4)2G5CA

180.0 C114C181(4)2G5CA

220.0 C114C221(4)2G5CA

270.0 C114C271(4)2G5CA

330.0 C114C331(4)2G5CA

82.0 C114C820(4)1G5CA

100.0 C114C101(4)1G5CA

120.0 C114C121(4)1G5CA

150.0 C114C151(4)1G5CA

180.0 C114C181(4)1G5CA

220.0 C114C221(4)1G5CA

270.0 C114C271(4)1G5CA

330.0 C114C331(4)1G5CA

390.0 C114C391(4)1G5CA

470.0 C114C471(4)1G5CA

560.0 C114C561(4)1G5CA

680.0 C114C681(4)1G5CA

200 VOLT – C114 STANDARD C0G

100 VOLT – C114 STANDARD C0G

CAPACITANCE

pF

KEMET

PART NUMBER

390.0 C124C391(4)2G5CA

470.0 C124C471(4)2G5CA

560.0 C124C561(4)2G5CA

820.0 C124C821(4)1G5CA

1,000.0 C124C102(4)1G5CA

680.0 C192C681(4)2G5CA

820.0 C192C821(4)2G5CA

1,000.0 C192C102(4)2G5CA

1,200.0 C192C122(4)2G5CA

1,500.0 C192C152(4)2G5CA

1,800.0 C192C182(4)2G5CA

2,200.0 C192C222(4)2G5CA

2,700.0 C192C272(4)2G5CA

3,300.0 C114C332(4)2G5CA

3,900.0 C114C392(4)2G5CA

4,700.0 C114C472(4)2G5CA

1,200.0

C192C122(

4)1G5CA

1,500.0

C192C152(

4)1G5CA

1,800.0

C192C182(

4)1G5CA

2,200.0

C192C222(

4)1G5CA

2,700.0

C192C272(

4)1G5CA

3,300.0

C192C332(

4)1G5CA

3,900.0

C192C392(

4)1G5CA

4,700.0

C192C472(

4)1G5CA

5,600.0

C192C562(

4)1G5CA

6,800.0

C192C682(

4)1G5CA

8,200.0

C192C822(

4)1G5CA

200 VOLT – C192 STANDARD C0G

100 VOLT – C192 STANDARD C0G

200 VOLT – C124 STANDARD C0G

100 VOLT – C124 STANDARD C0G

CAPACITANCE

pF

KEMET

PART NUMBER

5,600.0 C202C562(4)2G5CA

6,800.0 C202C682(4)2G5CA

8,200.0 C202C822(4)2G5CA

10,000.0 C202C103(4)2G5CA

12,000.0 C202C123(4)2G5CA

15,000.0 C202C153(4)2G5CA

18,000.0 C202C183(4)2G5CA

22000.0 C202C223(4)2G5CA

10,000.0 C202C103(4)1G5CA

12,000.0 C202C123(4)1G5CA

15,000.0 C202C153(4)1G5CA

18,000.0 C202C183(4)1G5CA

22,000.0 C202C223(4)1G5CA

27,000.0 C202C273(4)1G5CA

33,000.0 C202C333(4)1G5CA

27,000.0 C222C273(4)2G5CA

33,000.0 C222C333(4)2G5CA

39,000.0 C222C393(4)2G5CA

47,000.0 C222C473(4)2G5CA

39,000.0 C222C393(4)1G5CA

47,000.0 C222C473(4)1G5CA

56,000.0 C222C563(4)1G5CA

68,000.0 C222C683(4)1G5CA

82,000.0 C222C823(4)1G5CA

100,000.0 C222C104(4)1G5CA

200 VOLT – C222 STANDARD C0G

100 VOLT – C222 STANDARD C0G

200 VOLT – C202 STANDARD C0G

100 VOLT – C202 STANDARD C0G

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF

(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%

(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%

(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF

(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%

(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%

(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 31

RATINGS & PART NUMBER REFERENCE

Ceramic Molded

Axial/Radial - Standard

CERAMIC MOLDED/RADIAL – STANDARD

ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)

CAPACITANCE

pF

KEMET

PART NUMBER

1.0 C052C109(1)2G5CA

1.5 C052C159(1)2G5CA

2.2 C052C229(1)2G5CA

2.7 C052C279(1)2G5CA

3.3 C052C339(1)2G5CA

3.9 C052C399(1)2G5CA

4.7 C052C479(1)2G5CA

5.6 C052C569(1)2G5CA

6.8 C052C689(1)2G5CA

8.2 C052C829(1)2G5CA

10.0 C052C100(2)2G5CA

12.0 C052C120(2)2G5CA

15.0 C052C150(2)2G5CA

18.0 C052C180(2)2G5CA

22.0 C052C220(2)2G5CA

27.0 C052C270(3)2G5CA

33.0 C052C330(3)2G5CA

39.0 C052C390(3)2G5CA

47.0 C052C470(3)2G5CA

56.0 C052C560(4)2G5CA

68.0 C052C680(4)2G5CA

82.0 C052C820(4)2G5CA

100.0 C052C101(4)2G5CA

120.0 C052C121(4)2G5CA

150.0 C052C151(4)2G5CA

180.0 C052C181(4)2G5CA

220.0 C052C221(4)2G5CA

270.0 C052C271(4)2G5CA

330.0 C052C331(4)2G5CA

390.0 C052C391(4)2G5CA

470.0 C052C471(4)2G5CA

560.0 C052C561(4)2G5CA

680.0 C052C681(4)2G5CA

820.0 C052C821(4)2G5CA

1,000.0 C052C102(4)2G5CA

1,200.0 C052C122(4)2G5CA

1,500.0 C052C152(4)2G5CA

1,800.0 C052C182(4)2G5CA

2,200.0 C052C222(4)2G5CA

2,700.0 C052C272(4)2G5CA

390.0 C052C391(4)1G5CA

470.0 C052C471(4)1G5CA

560.0 C052C561(4)1G5CA

680.0 C052C681(4)1G5CA

820.0 C052C821(4)1G5CA

1,000.0 C052C102(4)1G5CA

1,200.0 C052C122(4)1G5CA

1,500.0 C052C152(4)1G5CA

1,800.0 C052C182(4)1G5CA

2,200.0 C052C222(4)1G5CA

2,700.0 C052C272(4)1G5CA

3,300.0 C052C332(4)1G5CA

3,900.0 C052C392(4)1G5CA

4,700.0 C052C472(4)1G5CA

100 VOLT – C052 SIZE C0G

200 VOLT – C052 SIZE C0G

CAPACITANCE

pF

KEMET

PART NUMBER

3,300.0 C062C332(4)2G5CA

3,900.0 C062C392(4)2G5CA

4,700.0 C062C472(4)2G5CA

5,600.0 C062C562(4)2G5CA

6,800.0 C062C682(4)2G5CA

8,200.0 C062C822(4)2G5CA

10,000.0 C062C103(4)2G5CA

5,600.0 C062C562(4)1G5CA

6,800.0 C062C682(4)1G5CA

8,200.0 C062C822(4)1G5CA

10,000.0 C062C103(4)1G5CA

12,000.0 C062C123(4)1G5CA

15,000.0 C062C153(4)1G5CA

18,000.0 C062C183(4)1G5CA

22,000.0 C062C223(4)1G5CA

12,000.0 C512C123(4)2G5CA

15,000.0 C512C153(4)2G5CA

18,000.0 C512C183(4)2G5CA

22,000.0 C512C223(4)2G5CA

27,000.0 C512C273(4)2G5CA

33,000.0 C512C333(4)2G5CA

39,000.0 C512C393(4)2G5CA

47,000.0 C512C473(4)2G5CA

56,000.0 C512C563(4)2G5CA

68,000.0 C512C683(4)2G5CA

27,000.0 C512C273(4)1G5CA

33,000.0 C512C333(4)1G5CA

39,000.0 C512C393(4)1G5CA

47,000.0 C512C473(4)1G5CA

56,000.0 C512C563(4)1G5CA

68,000.0 C512C683(4)1G5CA

82,000.0 C512C823(4)1G5CA

100,000.0 C512C104(4)1G5CA

82,000.0 C522C823(4)2G5CA

100,000.0 C522C104(4)2G5CA

120,000.0 C522C124(4)1G5CA

150,000.0 C522C154(4)1G5CA

180,000.0 C522C184(4)1G5CA

200 VOLT – C062 SIZE C0G

100 VOLT – C062 SIZE C0G

200 VOLT – C512 SIZE C0G

200 VOLT – C522 SIZE C0G

100 VOLT – C522 SIZE C0G

100 VOLT – C512 SIZE C0G

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF

(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%

(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%

(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF

(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%

(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%

(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630032

CERAMIC MOLDED/RADIAL – STANDARD

STABLE TEMPERATURE CHARACTERISTIC—X7R

RATINGS & PART NUMBER REFERENCE

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

10 10 C114C100K1R5CA

10 20 C114C100M1R5CA

12 10 C114C120K1R5CA

15 10 C114C150K1R5CA

15 20 C114C150M1R5CA

18 10 C114C180K1R5CA

22 10 C114C220K1R5CA

22 20 C114C220M1R5CA

27 10 C114C270K1R5CA

33 10 C114C330K1R5CA

33 20 C114C330M1R5CA

39 10 C114C390K1R5CA

47 10 C114C470K1R5CA

47 20 C114C470M1R5CA

56 10 C114C560K1R5CA

68 10 C114C680K1R5CA

68 20 C114C680M1R5CA

82 10 C114C820K1R5CA

100 10 C114C101K1R5CA

100 20 C114C101M1R5CA

120 10 C114C121K1R5CA

150 10 C114C151K1R5CA

150 20 C114C151M1R5CA

180 10 C114C181K1R5CA

220 10 C114C221K1R5CA

220 20 C114C221M1R5CA

270 10 C114C271K1R5CA

330 10 C114C331K1R5CA

330 20 C114C331M1R5CA

390 10 C114C391K1R5CA

470 10 C114C471K1R5CA

470 20 C114C471M1R5CA

560 10 C114C561K1R5CA

680 10 C114C681K1R5CA

680 20 C114C681M1R5CA

820 10 C114C821K1R5CA

1,000 10 C114C102K1R5CA

1,000 20 C114C102M1R5CA

1,200 10 C114C122K1R5CA

1,500 10 C114C152K1R5CA

1,500 20 C114C152M1R5CA

1,800 10 C114C182K1R5CA

2,200 10 C114C222K1R5CA

2,200 20 C114C222M1R5CA

2,700 10 C114C272K1R5CA

2,700 20 C114C332K1R5CA

3,300 10 C114C332M1R5CA

3,300 20 C114C392K1R5CA

3,900 10 C114C392K1R5CA

4,700 10 C114C472K1R5CA

4,700 20 C114C472M1R5CA

5,600 10 C114C562K5R5CA

6,800 10 C114C682K5R5CA

6,800 20 C114C682M5R5CA

8,200 10 C114C822K5R5CA

10,000 10 C114C103K5R5CA

10,000 20 C114C103M5R5CA

100 VOLT – C114 SIZE

50 VOLT – C114 SIZE

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

5,600 10 C124C562K1R5CA

6,800 10 C124C682K1R5CA

6,800 20 C124C682M1R5CA

8,200 10 C124C822K1R5CA

10,000 10 C124C103K1R5CA

10,000 20 C124C103M1R5CA

12,000 10 C124C123K5R5CA

15,000 10 C124C153K5R5CA

15,000 20 C124C153M5R5CA

18,000 10 C124C183K5R5CA

22,000 10 C124C223K5R5CA

22,000 20 C124C223M5R5CA

27,000 10 C124C273K5R5CA

33,000 10 C124C333K5R5CA

33,000 20 C124C333M5R5CA

39,000 10 C124C393K5R5CA

47,000 10 C124C473K5R5CA

47,000 20 C124C473M5R5CA

12,000 10 C192C123K1R5CA

15,000 10 C192C153K1R5CA

15,000 20 C192C153M1R5CA

18,000 10 C192C183K1R5CA

22,000 10 C192C223K1R5CA

22,000 20 C192C223M1R5CA

27,000 10 C192C273K1R5CA

33,000 10 C192C333K1R5CA

33,000 20 C192C333M1R5CA

39,000 10 C192C393K1R5CA

47,000 10 C192C473K1R5CA

47,000 20 C192C473M1R5CA

56,000 10 C192C563K1R5CA

68,000 10 C192C683K1R5CA

68,000 20 C192C683M1R5CA

82,000 10 C192C823K1R5CA

100,000 10 C192C104K1R5CA

100,000 20 C192C104M1R5CA

56,000 10 C192C563K5R5CA

68,000 10 C192C683K5R5CA

68,000 20 C192C683M5R5CA

82,000 10 C192C823K5R5CA

100,000 10 C192C104K5R5CA

100,000 20 C192C104M5R5CA

120,000 10 C192C124K5R5CA

150,000 10 C192C154K5R5CA

150,000 20 C192C154M5R5CA

180,000 10 C192C184K5R5CA

220,000 10 C192C224K5R5CA

220,000 20 C192C224M5R5CA

270,000 10 C192C274K5R5CA

100 VOLT – C124 SIZE

50 VOLT – C192 SIZE

50 VOLT – C124 SIZE

100 VOLT – C192 SIZE

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

56,000 10 C202C563K1R5CA

68,000 10 C202C683K1R5CA

68,000 20 C202C683M1R5CA

82,000 10 C202C823K1R5CA

100,000 10 C202C104K1R5CA

100,000 20 C202C104M1R5CA

120,000 10 C202C124K1R5CA

150,000 10 C202C154K1R5CA

150,000 20 C202C154M1R5CA

180,000 10 C202C184K1R5CA

220,000 10 C202C224K1R5CA

220,000 20 C202C224M1R5CA

270,000 10 C202C274K1R5CA

330,000 10 C202C334K1R5CA

330,000 20 C202C334M1R5CA

470,000 10 C202C474K5R5CA

470,000 20 C202C474M5R5CA

680,000 10 C202C684K5R5CA

680,000 20 C202C684M5R5CA

1,000,000 10 C202C105K5R5CA

1,000,000 20 C202C105M5R5CA

470,000 10 C222C474K1R5CA

470,000 20 C222C474M1R5CA

680,000 10 C222C684K1R5CA

680,000 20 C222C684M1R5CA

1,000,000 10 C222C105K1R5CA

1,000,000 20 C222C105M1R5CA

2,200,000 10 C222C225K5R5CA

2,200,000 20 C222C225M5R5CA

3,300,000 10 C222C335K5R5CA

3,300,000 20 C222C335M5R5CA

50 VOLT – C222 SIZE

100 VOLT – C222 SIZE

100 VOLT – C202 SIZE

50 VOLT – C202 SIZE

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 33

RATINGS & PART NUMBER REFERENCE

Ceramic Molded

Axial/Radial - Standard

CERAMIC MOLDED/RADIAL – STANDARD

STABLE TEMPERATURE CHARACTERISTIC—X7R

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

10 10 C052C100K2R5CA

10 20 C052C100M2R5CA

12 10 C052C120K2R5CA

15 10 C052C150K2R5CA

15 20 C052C150M2R5CA

18 10 C052C180K2R5CA

22 10 C052C220K2R5CA

22 20 C052C220M2R5CA

27 10 C052C270K2R5CA

33 10 C052C330K2R5CA

33 20 C052C330M2R5CA

39 10 C052C390K2R5CA

47 10 C052C470K2R5CA

47 20 C052C470M2R5CA

56 10 C052C560K2R5CA

68 10 C052C680K2R5CA

68 20 C052C680M2R5CA

82 10 C052C820K2R5CA

100 10 C052C101K2R5CA

100 20 C052C101M2R5CA

120 10 C052C121K2R5CA

150 10 C052C151K2R5CA

150 20 C052C151M2R5CA

180 10 C052C181K2R5CA

220 10 C052C221K2R5CA

220 20 C052C221M2R5CA

270 10 C052C271K2R5CA

330 10 C052C331K2R5CA

330 20 C052C331M2R5CA

390 10 C052C391K2R5CA

470 10 C052C471K2R5CA

470 20 C052C471M2R5CA

560 10 C052C561K2R5CA

680 10 C052C681K2R5CA

680 20 C052C681M2R5CA

820 10 C052C821K2R5CA

1,000 10 C052C102K2R5CA

1,000 20 C052C102M2R5CA

200 VOLT – C052 SIZE

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

1,200 10 C052C122K1R5CA

1,500 10 C052C152K1R5CA

1,500 20 C052C152M1R5CA

1,800 10 C052C182K1R5CA

2,200 10 C052C222K1R5CA

2,200 20 C052C222M1R5CA

2,700 10 C052C272K1R5CA

3,300 10 C052C332K1R5CA

3,300 20 C052C332M1R5CA

3,900 10 C052C392K1R5CA

4,700 10 C052C472K1R5CA

4,700 20 C052C472M1R5CA

5,600 10 C052C562K1R5CA

6,800 10 C052C682K1R5CA

6,800 20 C052C682M1R5CA

8,200 10 C052C822K1R5CA

10,000 10 C052C103K1R5CA

10,000 20 C052C103M1R5CA

12,000 10 C052C123K5R5CA

15,000 10 C052C153K5R5CA

15,000 20 C052C153M5R5CA

18,000 10 C052C183K5R5CA

22,000 10 C052C223K5R5CA

22,000 20 C052C223M5R5CA

27,000 10 C052C273K5R5CA

33,000 10 C052C333K5R5CA

33,000 20 C052C333M5R5CA

39,000 10 C052C393K5R5CA

47,000 10 C052C473K5R5CA

47,000 20 C052C473M5R5CA

56,000 10 C052C563K5R5CA

68,000 10 C052C683K5R5CA

68,000 20 C052C683M5R5CA

82,000 10 C052C823K5R5CA

100,000 10 C052C104K5R5CA

100,000 20 C052C104M5R5CA

1,200 10 C062C122K2R5CA

1,500 10 C062C152K2R5CA

1,500 20 C062C152M2R5CA

1,800 10 C062C182K2R5CA

2,200 10 C062C222K2R5CA

2,200 20 C062C222M2R5CA

2,700 10 C062C272K2R5CA

3,300 10 C062C332K2R5CA

3,300 20 C062C332M2R5CA

3,900 10 C062C392K2R5CA

4,700 10 C062C472K2R5CA

4,700 20 C062C472M2R5CA

5,600 10 C062C562K2R5CA

6,800 10 C062C682K2R5CA

6,800 20 C062C682M2R5CA

8,200 10 C062C822K2R5CA

10,000 10 C062C103K2R5CA

10,000 20 C062C103M2R5CA

100 VOLT – C052 SIZE

50 VOLT – C052 SIZE

200 VOLT – C062 SIZE

CAPACI-

TANCE

pF

TOL.

%

KEMET

PART NUMBER

12,000 10 C062C123K1R5CA

15,000 10 C062C153K1R5CA

15,000 20 C062C153M1R5CA

18,000 10 C062C183K1R5CA

22,000 10 C062C223K1R5CA

22,000 20 C062C223M1R5CA

27,000 10 C062C273K1R5CA

33,000 10 C062C333K1R5CA

33,000 20 C062C333M1R5CA

39,000 10 C062C393K1R5CA

47,000 10 C062C473K1R5CA

47,000 20 C062C473M1R5CA

56,000 10 C062C563K1R5CA

68,000 10 C062C683K1R5CA

68,000 20 C062C683M1R5CA

82,000 10 C062C823K1R5CA

100,000 10 C062C104K1R5CA

100,000 20 C062C104M1R5CA

120,000 10 C062C124K5R5CA

150,000 10 C062C154K5R5CA

150,000 20 C062C154M5R5CA

180,000 10 C062C184K5R5CA

220,000 10 C062C224K5R5CA

220,000 20 C062C224M5R5CA

270,000 10 C062C274K5R5CA

330,000 10 C062C334K5R5CA

330,000 20 C062C334M5R5CA

390,000 10 C062C394K5R5CA

470,000 10 C062C474K5R5CA

470,000 20 C062C474M5R5CA

560,000 10 C062C564K5R5CA

680,000 10 C062C684K5R5CA

680,000 20 C062C684M5R5CA

820,000 10 C062C824K5R5CA

1,000,000 10 C062C105K5R5CA

1,000,000 20 C062C105M5R5CA

1,000,000 10 C512C105K5X5CA

1,000,000 20 C512C105M5X5CA

1,500,000 10 C512C155K5X5CA

1,500,000 20 C512C155M5X5CA

2,000,000 10 C512C205K5X5CA

2,000,000 20 C512C205M5X5CA

2,200,000 10 C512C225K5X5CA

2,200,000 20 C512C225M5X5CA

1,000,000 10 C522C105K1X5CA

1,000,000 20 C522C105M1X5CA

2,700,000 10 C522C275K5X5CA

2,700,000 20 C522C275M5X5CA

3,300,000 10 C522C335K5X5CA

3,300,000 20 C522C335M5X5CA

50 VOLT – C522 SIZE

100 VOLT – C062 SIZE

50 VOLT – C062 SIZE

50 VOLT – C512 SIZE

100 VOLT – C522 SIZE

1,000,000 10 C062C105K1R5CA

1,000,000 20 C062C105M1R5CA

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630046

CERAMIC LEADED

PACKAGING INFORMATION

Ceramic Axial

Lead Tape and Reel Packaging

KEMET offers standard reeling of Molded and Conformally

Coated Axial Leaded Ceramic Capacitors for automatic insertion

or lead forming machines per EIA specification RS-296. KEMET’s

internal specification four-digit suffix, 7200, is placed at the end of

the part number to designate tape and reel packaging, ie:

C410C104Z5U5CA7200.

Paper (50 lb.) test minimum is inserted between the layers of

capacitors wound on reels for component pitch ≤0.400”.

Capacitor lead length may extend only a maximum of .0625”

(1.59mm) beyond the tapes’ edges. Capacitors are centered in a

row between the two tapes and will deviate only ± 0.031

(0.79mm) from the row center. A minimum of 36” (91.5 cm) leader

tape is provided at each end of the reel capacitors. Universal

splicing clips are used to connect the tape. Standard reel

quantities are shown on page 48.

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 47

Tape and Reel Packaging

CERAMIC LEADED

PACKAGING INFORMATION

©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630048

CERAMIC LEADED

PACKAGING INFORMATION

KEMET

Series

Military

Style

Military

Specification

Standard (1)

Bulk

Quantity

Ammo Pack

Quantity

Maximum

Maximum

Reel

Quantity

Reel

Size

C114C-K-G CK12, CC75 MIL-C-11015/ 200/Box 5000 12"

C124C-K-G CK13, CC76 MIL-PRF-20 200/Box 5000 12"

C192C-K-G CK14, CC77 100/Box 3000 12"

C202C-K CK15 25/Box 500 12"

C222C-K CK16 10/Tray 300 12"

C052C-K-G CK05, CC05 100/Bag 2000 2000 12"

C062C-K-G CK06, CC06 100/Bag 1500 1500 12"

C114G CCR75 MIL-PRF-20 200/Box 5000 12"

C124G CCR76 200/Box 5000 12"

C192G CCR77 100/Box 3000 12"

C202G CC78-CCR78 25/Box 500 12"

C222G CC79-CCR79 10/Tray 300 12"

C052/56G CCR05 100/Bag 1700 12"

C062/66G CCR06 100/Bag 1500 12"

C512G CC07-CCR07 Footnote (2) N/A N/A

C522G CC08-CCR08 Footnote (2) N/A N/A

C114T CKR11 MIL-PRF-39014 200/Box 5000 12"

C124T CKR12 200/Box 5000 12"

C192T CKR14 100/Box 3000 12"

C202T CKR15 25/Box 500 12"

C222T CKR16 10/Tray 300 12"

C052/56T CKR05 100/Bag 1700 12"

C062/66T CKR06 100/Bag 1500 12"

C31X 500/Bag 2500 2500 12"

C32X 500/Bag 2500 2500 12"

C33X 250/Bag 1500 1500 12"

C340 100/Bag 1000 1000 12"

C350 50/Bag N/A 500 12"

C410 300/Box 4000 5000 12"

C412 200/Box 4000 5000 12"

C420 300/Box 4000 5000 12"

C430 200/Box 2000 2500 12"

C440 200/Box 2000 2500 12"

C512 N/A N/A Footnote (2) N/A N/A

C522 N/A N/A Footnote (2) N/A N/A

C617 250/Bag 1000 12"

C622/C623 100/Bag 500 12"

C627/C628 100/Bag 500 12"

C630/C631 100/Bag 500 12"

C637/C638 50/Bag 500 12"

C640/C641 50/Bag 500 12"

C642/C643 50/Bag 500 12"

C647/C648 50/Bag 500 12"

C657/C658 50/Bag 500 12"

C667/C668 50/Bag 500 12"

CERAMIC PACKAGING

NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.

(2) Quantity varies. For further details, please consult the factory.