EV-ADF5356SD1Z User Guide UG-1087 One Technology Way * P.O. Box 9106 * Norwood, MA 02062-9106, U.S.A. * Tel: 781.329.4700 * Fax: 781.461.3113 * www.analog.com Evaluating the ADF5356 Frequency Synthesizer for Phase-Locked Loops FEATURES ONLINE RESOURCES Self contained board, including ADF5356 frequency synthesizer with integrated voltage controlled oscillator (VCO), differential 122.88 MHz temperature controlled crystal oscillator (TCXO), loop filter (5 kHz), USB interface, and voltage regulators Windows-based software allows control of synthesizer functions from a PC Externally powered by 6 V Documents Needed ADF5356 data sheet EV-ADF5356SD1Z user guide PLL Software Installation Guide Required Software Analog Devices, Inc., ADF5356 software, Version 1.1.6 or higher (download at www.analog.com/ADF5356) EQUIPMENT NEEDED The EV-ADF5356SD1Z evaluates the performance of the ADF5356 frequency synthesizer with integrated VCO for phaselocked loops (PLLs). A photograph of the evaluation board is shown in Figure 1. The evaluation board contains the ADF5356 synthesizer with integrated VCO, a differential 122.88 MHz reference TCXO, a loop filter, a USB interface, power supply connectors, and subminiature Version A (SMA) connectors. A USB cable is included to connect the board to a PC USB port. GENERAL DESCRIPTION Windows-based PC with USB port for evaluation software System demonstration platform, serial only (SDP-S) EVAL-SDP-CS1Z controller board Power supply (6 V) Spectrum analyzer 50 terminators EVALUATION KIT CONTENTS For easy programming of the synthesizer, download the Windows(R)-based software from www.analog.com/ADF5356. EV-ADF5356SD1Z USB cable This board requires an SDP-S controller board that is not supplied with the kit. The SDP-S controller board allows software programming of the ADF5356 device. For full details on the ADF5356, see the ADF5356 data sheet, which must be consulted in conjunction with this user guide when using this evaluation board. 15361-001 EV-ADF5356SD1Z EVALUATION BOARD PHOTOGRAPH Figure 1. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 19 UG-1087 EV-ADF5356SD1Z User Guide TABLE OF CONTENTS Features .............................................................................................. 1 RF Output .......................................................................................4 Equipment Needed ........................................................................... 1 Loop Filter ......................................................................................4 Evaluation Kit Contents ................................................................... 1 Reference Source ...........................................................................4 Online Resources .............................................................................. 1 Default Configuration ..................................................................4 General Description ......................................................................... 1 Evaluation Board Setup ................................................................5 Evaluation Board Photograph......................................................... 1 Evaluation Board Software ...............................................................6 Revision History ............................................................................... 2 Main Controls ................................................................................6 Getting Started .................................................................................. 3 Evaluation and Test ...........................................................................7 Software Installation Procedures ................................................ 3 Evaluation Board Schematics and Artwork ...................................8 Evaluation Board Setup Procedures........................................... 3 Ordering Information .................................................................... 17 Evaluation Board Hardware ............................................................ 4 Bill of Materials ........................................................................... 17 Power Supplies .............................................................................. 4 REVISION HISTORY 8/2017--Revision 0: Initial Version Rev. 0 | Page 2 of 19 EV-ADF5356SD1Z User Guide UG-1087 GETTING STARTED SOFTWARE INSTALLATION PROCEDURES EVALUATION BOARD SETUP PROCEDURES See the ADF5356 product page for the EV-ADF5356SD1Z control software. For the software installation procedure, see the PLL Software Installation Guide. To run the software, 1. 2. 3. Click the ADF5356 file on the desktop or from the Start menu. On the Select Device and Connection tab, click ADF5356 and SDP board (black), and then click Connect (see Figure 2). When connecting the board, allow 5 sec to 10 sec for the label on the status bar to change. 15361-002 Under the File menu, the current settings can be saved to, and loaded from, a text file. Figure 2. Software Front Panel Display--Select Device and Connection Rev. 0 | Page 3 of 19 UG-1087 EV-ADF5356SD1Z User Guide EVALUATION BOARD HARDWARE The EV-ADF5356SD1Z requires an SDP-S controller board, EVAL-SDP-CS1Z (SDP-B is not recommended). LOOP FILTER The EV-ADF5356SD1Z schematics are shown in Figure 7, Figure 8, and Figure 9. The silkscreens for the evaluation board are shown in Figure 10 and Figure 11. POWER SUPPLIES The board is powered by a 6 V power supply connected to the red and black banana connectors. Connect the red connector to a 6 V power supply and the black connector to ground. The power supply circuitry allows the user two or three separate low dropout (LDO) regulators to feed the ADF5356 (using fewer LDO regulators increases the risk of spur contaminated dc feeds). For lowest noise at 100 kHz offset, use the following components (that are inserted on the evaluation board) with a 0.9 mA charge pump current: C60 = 22 nF, C59 = 0.47 F, C61 = 10 nF, C73 = 10 pF R14 = 220 , R17 = 470 For lowest rms phase noise, use the following components with a 0.9 mA charge pump current: C60 = 1.2 nF, C59 = 33 nF, C61 = 390 pF, C73 = 10 pF R14 = 1 k, R17 = 3.3 k C59 C60 RPIN18 The charge pump and VCO supply pins are powered from a 5 V ADM7150 high performance, low noise regulator. The remaining supplies are powered from a 3.3 V ADM7150 high performance, low noise regulator. The loop filter schematic is included in the board schematic in Figure 7. Figure 3 shows the loop filter component placements. R14 C61 R1 R17 LED1 indicates when the ADF5356 is powered on. Use Switch S1 to switch the 6 V power to the board on and off. C73 R5 RF OUTPUT The EV-ADF5356SD1Z has one pair of SMA output connectors: RFOUTA+ and RFOUTA- (differential outputs). Because they are sensitive to impedance mismatch, connect the RF outputs to equal load impedances. If using only one port of a differential pair, terminate the complementary port with an equal load terminator (in general, a 50 terminator). The RFOUTB SMA connector is a single-ended RF output that operates from 6.8 GHz to 13.6 GHz. If only RFOUTB is used, power off the RFOUTA+ and RFOUTA- connectors. If left on, terminate both RFOUTA+ and RFOUTA- SMA connectors with 50 terminators. RVTUNE 15361-003 RCPOUT Figure 3. Loop Filter Placement REFERENCE SOURCE The evaluation board contains a 122.88 MHz differential output TCXO from Vectron International. If preferred, the user may supply either a single-ended or differential reference input to the REFINA/REFINB SMA connectors. When using an external reference, remove R12 to disconnect the power rail from the TCXO. To use a single-ended reference, connect a low noise 122.88 MHz reference source to SMA REFINB, and connect a 50 terminator to SMA REFINA. Remove Resistor R27 (100 ). To use a differential reference, connect the differential signal to the SMA REFINA and SMA REFINB connectors. The differential REFINA/REFINB SMA connectors can operate at up to a 500 MHz input frequency. DEFAULT CONFIGURATION All components necessary for local oscillator generation are inserted on the board. This board is shipped with the ADF5356 synthesizer with an integrated VCO, a differential 122.88 MHz reference TCXO, and a 10 kHz loop filter (ICP = 0.9 mA). Rev. 0 | Page 4 of 19 EV-ADF5356SD1Z User Guide UG-1087 EVALUATION BOARD SETUP SDP-S BOARD PC VSUPPLY EXTERNAL POWER SWITCH EXTERNAL DC SUPPLY PLL POWER LED EXTERNAL DC GND SPECTRUM ANALYZER SIGNAL GENERATOR LOCK DETECT LED REFERENCE IN/OUT REFINB TCXO LOOP FILTER REFINA REFERENCE (OPTIONAL) ADF5356 (UNDERNEATH BOARD) RFOUTA+ RFOUTB 15361-004 RFOUTA- Figure 4. Evaluation Setup Block Diagram Rev. 0 | Page 5 of 19 UG-1087 EV-ADF5356SD1Z User Guide EVALUATION BOARD SOFTWARE MAIN CONTROLS The Main Controls tab (see Figure 5) selects the RF and user configurable register settings. Consult the register descriptions in the ADF5356 data sheet for details. Default settings are recommended for most registers. In Register 4, program CP current to match the value used for the loop filter design. 15361-005 In RF Settings, ensure that VCOout (MHz) equals the VCO frequency. Set Output divider to give the required RFoutA (MHz). Ensure that Reference freq equals the applied reference signal. The PFD frequency is calculated from the reference frequency, the R counter, the reference doubler, and the reference divide by 2. Ensure that the value in PFD (MHz) matches the value specified in the loop filter design. Figure 5. Software Front Panel Display--Main Controls Rev. 0 | Page 6 of 19 EV-ADF5356SD1Z User Guide UG-1087 EVALUATION AND TEST Figure 6 shows a phase noise plot of the SMA RFOUTA+ with the VCO frequency equal to 6.6 GHz. To evaluate and test the performance of the ADF5356, use the following procedure: -70 Rev. 0 | Page 7 of 19 -90 -110 -130 -150 -170 1k 10k 100k 1M 10M FREQUENCY OFFSET FROM CARRIER (Hz) Figure 6. Single Sideband Phase Noise 15361-006 PHASE NOISE (dBc/Hz) Install the ADF5356 software (see the PLL Software Installation Guide). 2. Follow the hardware driver installation procedure (Windows XP only). 3. Connect a 50 terminator to the RFOUTA- SMA connector. 4. Connect the EV-ADF5356SD1Z board to the SDP-S board. 5. Connect the 6 V power supply to the banana connectors and power up the board using S1 (check that LED1 is on). 6. Connect the USB cable from the SDP-S board to the PC. 7. Run the ADF5356 software. 8. Select ADF5356 and SDP board (black) in the Select Device and Connection tab of the software front panel display window (see Figure 2). 9. Click the Main Controls tab, and set the VCOout (MHz) to a frequency of 6600 MHz, and then click Write Init. Seq. 10. Connect the spectrum analyzer to the RFOUTA+ SMA connector. See Figure 4 for a typical evaluation setup. 11. Measure the output spectrum and single sideband phase noise. -50 1. +3.3V RA3 0 DNI CA3 1F DNI GND CA2 1F DNI GND C2 C1 REFINA GND 5 4 3 2 1 GND 5 OUT+ NC GND 2 3 125MHz OUT- 6 DNI 7 Y1_ALT VTUNE VCC 1 CA5 1F DNI GND 4 GND CA4 1F DNI GND 8 RA2 0 DNI REFINA AND REFINB ARE SPACED 15mm CENTER TO CENTER ON PCB CA1 100pF DNI GND 3 R8 51 DNI R7 51 DNI 1 Figure 7. Evaluation Board Schematic--Page 1 CE IN LE IN DATA IN CLK IN NC 1 R16 0 TP2 C44 100pF GND R19 1.8k GND R18 1.8k R23 1.8k TP6 C48 10pF GND C37 10pF GND C43 10pF GND C46 10pF GND C33 0.1F GND C53 0.1F GND ADF5356 29 REFINA 28 REFINB 1 CLK 2 DATA 3 LE 4 CE C45 0.1F GND C50 0.1F GND AVDD2 TP3 TP4 TP5 GND R25 1.5k GND R24 DNI +3.3V C41 1000pF R10 51 DNI GND VP DVDD REFINB CREG2 R12 +3.3V 0 5 4 3 2 1 C47 1F GND R9 51 +3.3V DNI C42 1000pF GND C39 1000pF R27 100 C40 1000pF 5 4 Y1 E/D GND 6 VDD TP1 GND 1 GND +3.3V R11 0 RA4 0 RA5 0 122.88MHz 2 CFO FO RA1 0 DNI 32 16 27 6 22 U1 GND GND GND R3 0 DNI GND C51 10pF 0201 R33 0 0201 R32 0 0201 VRF1 GND L7 4.7nH 0201 DNI GND L6 4.7nH 0201 DNI R1 0 C57 120pF C58 0.1F C21 1F C56 120pF GND C61 10000pF GND C23 DNI C3 10pF 0201 C60 22nF GND L2 C6 7.4nH 10pF 0201 0201 VRF1 GND L3 4.7nH 0201 DNI L1 7.4nH 0201 VRF1 A DS1 C R26 0 DNI R4 0 C19 10F GND 32K243-40ML5 RFOUTB 32K243-40ML5 GND RFOUTB GND RFOUTA- RF CHOKE MATCHED LINE WIDTH'S TRACE WIDTH = 380m RFOUTA- GND GND C17 4.7F GND VREF C15 1F DNI GND VBIAS VREGVCO RFOUTA+ C30 1000pF GND C27 1000pF GND C29 10pF GND C31 10pF GND C26 0.1F GND C28 10pF GND GND LOCK DETECT 32K243-40ML5 RFOUTA+ C73 10pF GND R5 VTUNE 0 LOOP FILTER PLACE ON BOTTOM SIDE OF PCB SHIELD SIGNALS WITH VIAS R17 470 C55 0.1F GND GND AVDD1 R21 0 C54 10pF R14 220 C59 0.47F C12 1F GND GND VVCO GND GND CPOUT RCPOUT 0 IN VRF C9 1F C32 1000pF GND C36 1000pF GND C35 0.1F R22 68 R20 0 DNI IN MUXOUT MUXOUT RMUX 0 1 C34 10pF GND PDRF PDRF R2 10k +3.3V C25 10pF CREG1 C38 10pF ADF5355BCPZ 30 25 7 5 10 17 20 24 23 19 11 12 14 R6 5.1k GND MUXOUT CREG1 CPOUT AVDD VRF VVCO VTUNE VBIAS VREF VREGVCO RFOUTA+ RFOUTA- RFOUTB CREG2 AVDD DVDD VP RSET AGND CPGND SDGND AGNDVCO AGNDVCO AGNDRF AGNDRF PDBRF PAD 9 8 31 18 21 13 15 26 PAD Rev. 0 | Page 8 of 19 15361-007 +3.3V UG-1087 EV-ADF5356SD1Z User Guide EVALUATION BOARD SCHEMATICS AND ARTWORK AVDD DVDD VRF VRF1 VVCO VP VRVCO G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G20 G21 G22 G23 G24 G25 G26 G27 G28 G29 G30 G31 G32 G33 G34 G35 G36 1 2 3 4 5 6 7 8 GND MUX/LE IN GND CVVCO 22F 0 RV7 GND CVP 22F Rev. 0 | Page 9 of 19 Figure 8. Evaluation Board Schematic--Page 2 GND CVRF1 22F RV5 DNI AVDD2 GND CVRF 22F GND CDVDD 22F GND CAVDD 22F GND 0 VRF1 TP_VRF1 RV31 1 0 VRF DVDD TP_VRF RV25 1 0 RV20 1 DNI VREF VBIAS GND C4 1F RV9 0 RV10 0 DNI GND REF VIN 4 GND PAD EP VR2 ADM7150ACPZ-5.0 1 VREG 3 2 VOUT BYP 7 5 REF_SENSE EN 6 8 3.3V RV30 0 0 RV26 RV4 DNI RV19 0 0 RV15 1k 0 GND C16 10F GND C2 10F RV3 0 RAVDD R3V3 GND C18 1F RV27 0 GND C5 1F RV16 0 LED1 RV28 0 DNI GND RV17 0 DNI GND GND VIN 4 GND PAD REF EP 4 VIN GND PAD EP VR5 ADM7150ACPZ-3.3 1 VREG 3 2 VOUT BYP 7 5 REF_SENSE EN 6 8 REF VR3 ADM7150ACPZ-3.3 1 VREG 3 2 VOUT BYP 5 7 REF_SENSE EN 6 8 R_VREGVCO VREGVCO PLACE VBIAS, VREF 7 VREGVCO RESISTORS CLOSE TO DUT PINS 0 AVDD2 RV2 0 AVDD1 TP_DVDD 1 TP_AVDD2 0 RV14 1 1 DNI R_VREF C1 10F GND R_VBIAS RV12 0 RV8 0 RV6 0 TP_+3.3V VVCO VP TP_AVDD1 1 TP_VVCO 0 + CVRVCO 22F + + TP_VP RV1 1 GND GND C22 10F RV29 0 GND C24 + 1F C20 10F GND GND C11 10F RV18 0 C76 100F GND 6V C75 100F GND 6V 6V C14 + 10F C8 10F GND GND C10 10F RV11 0 C13 + C74 10F 100F GND GND C7 10F GND GND + G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 G13 G14 G15 G16 1 2 3 4 P2 DNI 6V GND ZD1 RPIN18 0 DNI VSUPPLY DNI IN IN GND VSUPPLY_ALT LE MUX/LE MUXOUT IN IN IN 1 2 3 JUMPER 3 PIN P3 CPOUT SHIELD SIGNALS WITH VIAS ALL THE WAY TO THE DUT PINS. VTUNE PLACE VTUNE, CPOUT AND SW RESISTORS CLOSE TO DUT PINS GND 1 2 1 2 GND 5 4 3 2 1 VSUPPLY RVTUNE 0 DNI 1 3 3 GND GND C71 22F 1 S1 15361-008 P1 EV-ADF5356SD1Z User Guide UG-1087 EV-ADF5356SD1Z User Guide CN1 IN DATA IN MUXOUT IN CLK IN VIO_+3.3V RE3 TBD0603 DNI RE1 100k GND RE2 100k GND 1 2 3 6 7 8 RLE 1.5k LE RDATA 1.5k RMUXOUT 0 RCLK 1.5k UE1 A0 VCC A1 5 SDA_0 SDA A2 SCL WP VSS 4 24LC32A-I/MS SDA 1 SCL GND SCL_0 PDRF CE 1 R28 0 DNI IN IN R29 0 DNI R30 0 DNI GND LE IN R31 0 DNI Figure 9. Evaluation Board Schematic--Page 3 Rev. 0 | Page 10 of 19 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 GND CN1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 GND 15361-009 UG-1087 UG-1087 15361-010 EV-ADF5356SD1Z User Guide Figure 10. Evaluation Board Silkscreen--Top Side Rev. 0 | Page 11 of 19 EV-ADF5356SD1Z User Guide 15361-011 UG-1087 Figure 11. Evaluation Board Silkscreen--Reverse Side Rev. 0 | Page 12 of 19 UG-1087 15361-012 EV-ADF5356SD1Z User Guide Figure 12. Evaluation Board Layer 1--Primary Rev. 0 | Page 13 of 19 EV-ADF5356SD1Z User Guide 15361-013 UG-1087 Figure 13. Evaluation Board Layer 2--Ground Rev. 0 | Page 14 of 19 UG-1087 15361-014 EV-ADF5356SD1Z User Guide Figure 14. Evaluation Board Layer 3--Power Rev. 0 | Page 15 of 19 EV-ADF5356SD1Z User Guide 15361-015 UG-1087 Figure 15. Evaluation Board Layer 4--Secondary Rev. 0 | Page 16 of 19 EV-ADF5356SD1Z User Guide UG-1087 ORDERING INFORMATION BILL OF MATERIALS Table 1. Reference Designator C1, C2, C7, C8, C10, C11, C16, C20, C22 C9, C12, C21, C47 Description Ceramic multilayer capacitor, X5R Value1 10 F Manufacturer TDK Part Number C2012X5R1E106K085AC Ceramic capacitor, X7R 1 F 0603YC105KAT2A C4, C5, C13, C14, C18, C24 C17 C19 C25, C28, C29, C31, C34, C37, C38, C43, C46, C48, C54 C27, C30, C32, C36, C39 to C42 C3, C6, C51 Ceramic capacitor, X8R Ceramic capacitor, X5R Ceramic capacitor, X5R RF/microwave capacitor, C0G 1 F 4.7 F 10 F 10 pF Ceramic capacitor, C0G, 0402 1000 pF Allied Electronics TDK TDK TDK Allied Electronics Murata Ceramic chip capacitor, RF 10 pF Allied Electronics KEMET 0201ZK100GBSTR Yageo Murata Murata Allied Electronics Yageo Allied Electronics Murata Allied Electronics Allied Electronics HIROSE 2238 867 15101 GRM1555C1H121JA01 GRM188F51C474ZA01D 0603YC223KAT2A C26, C33, C35, C45, C50, C53, C55, C58 C44 C56, C57 C59 C60 Ceramic capacitor, X7R 0.1 F Ceramic capacitor, NP0 Ceramic capacitor, C0G, 0402 Ceramic capacitor, Y5V Ceramic capacitor 100 pF 120 pF 0.47 F 22 nF C61 C71 Ceramic capacitor, X7R Solid tantalum electrolytic capacitor 10,000 pF 22 F C73 C74 to C76 Chip capacitor, C0G, 0603 Tantalum chip capacitor 10 pF 100 F CVP, CVRF, CAVDD, CDVDD, CVRF1, CVVCO, CVRVCO CN1 22 F DS1, LED1 Tantalum capacitor surface-mount device (SMD) Connector printed circuit board (PCB), vertical type receptacle SMD LED, 570 nm, SMD (green) GND Connector PCB, single socket (black) L1, L2 SCL, SDA, TP1 to TP6, PDRF, TP_VP, MUXOUT, TP_VRF, TP_DVDD, TP_VRF1, TP_VVCO, TP_+3.3V, TP_AVDD1, TP_AVDD2 P3 R1, R4, R5, R12, R21, RV1 to RV3, RV6 to RV9, R3V3, RV11, RV12, RV14 to RV16, RV18 to RV20, RV25 to RV27, RV29 to RV31, RMUXOUT R11, R16, RMUX, RCPOUT, R_VREGVCO R14 Inductor chip Connector PCB, test point (yellow) R17 7.4 nH C2012X8R1C105K125AB C1608X5R1C475K080AC C1608X5R1A106M080AC 04025U100GAT2A GRM1555C1H102JA01 C0402C104K4RACTU CC0603KRX7R9BB103 TCJC226M025R0100 GRM1885C1H100JA01D TAJB107K006R TAJB226K016R FX8-120S-SV(21) Avago Technologies Del-Tron Precision, Inc. Coilcraft Components Corporation HSMG-C170 571-0100 0302CS-7N4XJLU TP-104-01-04 Connector PCB, Header 3 Film SMD resistor, 0603 0 Molex Multicomp 22-28-4033 MC0603WG00000T5E-TC Resistor thick film chip 0 Multicomp 0402WGF0000TCE Film SMD resistor, 0603 220 Multicomp Film SMD resistor, 0603 470 Multicomp MC 0.063W 0603 1% 220R MC 0.063W 0603 1% 470R Rev. 0 | Page 17 of 19 UG-1087 Reference Designator R18, R19, R23 R2 R22 R25, RLE, RCLK, RDATA R27 R32, R33 R6 RAVDD RE1, RE2 RE3 REFINA, REFINB RFOUTB, RFOUTA+, RFOUTA- S1 U1 UE1 VR2 VR3, VR5 VSUPPLY VSUPPLY_ALT Y1 ZD1 1 2 EV-ADF5356SD1Z User Guide Description Film SMD resistor, 0603 Precision thick film chip, resistor R0603 Film SMD resistor, 0603 Precision thick film chip resistor, R0805 High frequency thin film chip resistor Chip SMD resistor, 0201 Standard thick film chip resistor Precision thick film chip resistor, R0805 Precision thick film chip resistor, R0805 Do not install (TBD0603)2 PCB, coaxial SMA, end launch connector PCB, SMA right angle jack connector Value1 1.8 k 10 k 68 1.5 k 100 0 5.1 k 1 k 100 k Momentary single pole single throw switch IC, Analog Devices microwave wideband synthesizer with integrated VCO IC, 32 kB serial EEPROM IC, 800 mA, ultralow noise/high power supply rejection ratio (PSRR), RF linear regulator, 5.0 V output IC, 800 mA, ultralow noise/high PSRR, RF linear regulator, 3.3 V output Connector PCB, coaxial SMA, end launch (do not install) PCB, single socket (red) connector IC, crystal low voltage positive emitter coupled logic (LVPECL) Zener diode, 6.8 V, SOT-23 A component with no value listed means it is not applicable. TBD means no value assigned; component not inserted. Rev. 0 | Page 18 of 19 Manufacturer Multicomp Panasonic Multicomp Panasonic Vishay Panasonic Vishay Panasonic Panasonic Johnson Rosenberger Part Number MC 0.063W 0603 1% 1K8 ERJ-3EKF1002V MC 0.063W 0603 1% 68R ERJ-6ENF1501V FC0402E1000BST1 ERJ-1GE0R00C CRCW04025K10FKED ERJ-6ENF1001V ERJ-6ENF1003V Do not install 142-0701-801 32K243-40ML5 Alcoswitch Analog Devices TT11AGPC-1 ADF5356BCPZ Microchip Technology, Inc. Analog Devices 24LC32A-I/MS ADM7150ACPZ-5.0 Analog Devices ADM7150ACPZ-3.3 Do not install Del-Tron Precision, Inc. Vectron International Philips 571-0500 VCC6-LAB-122M880000 BZX84-C6V8 EV-ADF5356SD1Z User Guide UG-1087 NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the "Evaluation Board"), you are agreeing to be bound by the terms and conditions set forth below ("Agreement") unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you ("Customer") and Analog Devices, Inc. ("ADI"), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term "Third Party" includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED "AS IS" AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER'S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI'S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. (c)2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG15361-0-8/17(0) Rev. 0 | Page 19 of 19