ALUMINUMELECTROLYTICCAPACITORS UCM Chip Type, Low Impedance Chip type, low impedance temperature range up to +105C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. UCL Smaller Higher capacitance UCM Smaller Higher capacitance Specifications Specifications UCV Item Item PerformancePerformance Characteristics Characteristics Category Temperature TemperatureRange Range Category Rated Voltage Range Range Rated Voltage Rated Capacitance Range Rated Capacitance Range Capacitance Tolerance Capacitance Tolerance Leakage Current Leakage Current Tangent of loss angle (tan ) Tangent of loss angle (tan ) - 55 to +105C -55 to +105C 6.36.3 to 50V to 50V 10 to 2200 F 10 to 2200F 20% at 120Hz, 20C 20% at 120Hz, 20C of rated voltage, leakage current is not more than 0.01CV After 2 minute's application After 2 minutes' application of rated voltage at 20C, leakage current is not more than 0.01 CV (A). frequency : 120Hz, Measurement Rated voltage (V) 6.3 10 Rated voltage (V) 0.266.3 tan (MAX.) 16 0.1910 0.19 6.3 Rated voltage 2 6.3 Z-25C /(V) Z+20C Stability at Low Temperature Impedance ratio Z- 25C / Z+20C 3 2 ratio Z-40C / Z+20C Stability at Low Temperature ZT /Impedance Z20 (MAX.) Z- 40C / Z+20C 4 3 ZT / Z20 (MAX.) Z-55C / Z+20C Z- 55C / Z+20C 4 Endurance Endurance Shelf Life Shelf Life Resistance to soldering heat Resistance to soldering Marking heat 0.26 Rated voltage (V) 25 0.16 16 0.14 16 216 32 43 4 After storing the capacitors under no load at 105C for 1000 hoursCapacitance and then performing voltage treatment based on JIS C 5101-4 Change Within 10% of the initial capacitance value clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. tan Less than or equal to the initial specified value The capacitors are kept on a hot plate for 30 seconds, which is LeakageCapacitance current Less thanWithin or equal value 10%toofthe theinitial initial specified capacitance value change maintained at 250C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan Black print on the case requirements listedtop. at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20C. Black print on the case top. Marking 1 C 0.2 0.3MAX. H C 0.2 0.3MAX. E B 0.2 a2 470E CM D 0.5 Series Capacitance L 0.5 Negative H Pressure relief vent 7 8 9 10 11 12 13 14 Size code Configuration Capacitance tolerance (20%) Rated capacitance (100F) Negative A 0.2 Lot No. 6 Rated voltage (16V) Series name Positive Plastic platform Trade mark 5 A 0.2 L 0.3 Voltage( E : 25V ) 4 A 0.2 Capacitance Lot No. 3 E B 0.2 D 0.5 a2 100C CM (4 to 6.3) A 0.2 Series 2 U CM 1 C 1 0 1 M C L 1 GS Type numbering system (Example : 16V 100 F) Taping code Configuration D Code 4 to 6.3 CL 8 * 10 NL Type 0.5MAX. Chip Type 0.5MAX. Positive Plastic platform Voltage( C : 16V ) (8,10 ) 50 Measurement frequency : 120Hz at 20C 0.10 50 Temperature : 20C 0.12 35 0.12 0.10 Measurement frequency : 120Hz 25 35 50 Measurement frequency : 120Hz 50 2 352 25 2 23 23 2 3 33 33 3 3 3 3 3 Capacitance Change Within 30% of the initial capacitance value tan 200% or less than the initial specified value Capacitance change Within 30% of the initial capacitance value The specifications listed at right shall be met Leakage current Less than or equal to the initial specified value tan 200% or less than the initial specified value when the capacitors are restored to 20C after the Less than or equal to the initial specified valueclause Leakage current After storing the capacitors no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 rated voltage is appliedunder for 2000 hours at 105C. 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. tan (MAX.) 0.16 10 210 32 43 4 35 0.14 25 (mm) DL 4 5.8 5 5.8 6.3 5.8 6.3 7.7 8 10 10 10 A 1.8 2.1 2.4 2.4 2.9 3.2 B 4.3 5.3 6.6 6.6 8.3 10.3 C 4.3 5.3 6.6 6.6 8.3 10.3 E 1.0 1.3 2.2 2.2 3.1 4.5 L 5.8 5.8 5.8 7.7 10 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 10 0.8 to 1.1 Voltage V Code Voltage V 6.3 j Code 6.3 j 10 A 10 A 16 C 16 C 25 E 25 E 35 V 35 V 50 H 50 H Dimension table in next page. 138 CAT.8100H ALUMINUMELECTROLYTICCAPACITORS UCM Dimensions V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 10 100 22 220 4 x 5.8 1.00 160 4 x 5.8 1.00 160 33 330 4 x 5.8 1.00 160 5 x 5.8 0.36 240 47 470 68 680 100 101 150 151 220 221 5 x 5.8 0.36 330 331 6.3 x 5.8 0.26 470 471 6.3 x 7.7 560 561 680 681 6.3 x 7.7 4 x 5.8 4 x 5.8 1.00 160 5 x 5.8 0.36 240 5 x 5.8 0.36 240 4 x 5.8 1.00 160 5 x 5.8 0.36 240 5 x 5.8 0.36 240 6.3 x 5.8 0.26 300 5 x 5.8 0.36 240 6.3 x 5.8 0.26 300 6.3 x 5.8 0.26 300 5 x 5.8 0.36 240 6.3 x 5.8 0.26 300 6.3 x 7.7 0.16 600 6.3 x 7.7 0.16 600 240 6.3 x 5.8 0.26 300 6.3 x 5.8 0.26 300 6.3 x 7.7 0.16 600 300 6.3 x 7.7 0.16 600 6.3 x 7.7 0.16 600 8 x 10 0.08 850 0.16 600 6.3 x 7.7 0.16 600 0.16 600 1.00 160 8 x 10 0.08 820 821 1000 102 1500 152 8 x 10 2200 222 10 x 10 0.08 0.08 850 10 x 10 0.08 850 10 x 10 85 0.88 165 5 x 5.8 0.88 165 6.3 x 5.8 0.68 195 6.3 x 7.7 0.34 350 8 x 10 0.18 670 10 x 10 0.12 900 0.06 1190 850 10 x 10 8 x 10 2.30 5 x 5.8 850 10 x 10 8 x 10 4 x 5.8 0.06 1190 0.06 1190 0.06 1190 x 0.06 1190 Impedance Rated ripple MAX. Impedance () at 20 100kHz, Rated ripple current(mArms) at 105 100kHz In this case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency coefficient of rated ripple current Frequency Frequency Coefficient Coefficient 50Hz 120Hz 300Hz 1kHz 10kHz or more 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more 0.35 0.35 0.50 0.50 0.64 0.64 0.83 0.83 1.00 1.00 Taping specifications are given in page 23. Recommended land size, soldering by refrow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 139 CAT.8100H