Integrated Device Technology, Inc. FAST CMOS 16-BiT BUFFER/LINE DRIVER IDT54/74FCT1G244T/AT/CT/ET IDT54/74FCT162244T/ATICT/ET IDT54/74FCT166244T/AT/CT IDT54/74FCT162H244T/AT/CT/ET ADVANCE INFORMATION FEATURES: Common features: - 0.5 MICRON CMOS Technology High-speed, low-power CMOS replacement for ABT functions - Typical tsk(o} (Output Skew) < 250ps - Low input and output leakage < 111A (max.) ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) - 25 mil pitch SSOP and Cerpack Packages and 19.6 mil pitch TSSOP Package Extended commercial range of -40C to +85C Features for FCT16244T/AT/CT/ET: High drive outputs (-32mA lon, 64mA IoL) Power off disable outputs permit live insertion - Typical VoLP (Output Ground Bounce) < 1.0V at Vcc = 5V, TA = 25C Features for FCT162244T/AT/CT/ET: - Balanced Output Drivers: +24mA (commercial), +16mA (military) ~ Reduced system switching noise Typical VoLP (Output Ground Bounce) < 0.6V at Vec = 5V,TA = 25C Features for FCT166244T/AT/CT: Light Drive Balanced Output: +8mA (commercial), +6mA (military) Minimal system switching noise Typical VoLP (Output Ground Bounce) < 0.25V at Vcc = 5V,TA = 28C Features for FCT162H244T/AT/CT/ET: - Bus Hold retains last active bus state during 3-state Eliminates the need for external pull up resistors FUNCTIONAL BLOCK DIAGRAM DESCRIPTION: The 16-Bit Buffer/Line Driver is forbusinterface orsignal buffering applications requiring high speed and low power dissipation. These devices have a flow through pin organization, and shrink packaging to simplify board layout. All inputs are designed with hysteresis for improved noise margin. The three-state controls allow independent 4-bit, 8-bit or combined 16-bit operation. These parts are plug in replacements for 54/74ABT 16244 where higher speed, lower noise or lower power dissipation levels are desired. The FCT16244T/AT/CT/ET are ideally suited for driving high capacitance loads (>200pF) and low impedance backplanes. These high drive" buffers are designed with power off disable capability to allow live insertion" of boards when used in a backplane interface. The FCT162244T/AT/CT/ET have balanced output current levels and current limiting resistors. These offer low ground bounce, minimal undershoot, and controlied output fall times, reducing the need for external series terminating resistors while still providing very high speed operation for loads of less than 200pF. The FCT166244T/AT/CT are suited for very low noise, point-to-point driving where there is a single receiver, or avery light lumped load (<SOpF). The buffers are designed to limit the output current to levels which will avoid noise and ringing on the signal lines without using external series terminating resistors. The FCT162H244T/AT/CT/ET have "Bus Hold" which re- tains the input's last state whenever the input goes to high impedance. This prevents "floating" inputs and eliminates the need for pull-up/down resistors. 10E 30E 1A1 v1 3A1 3Y1 1A2 12 3A2 3Y2 1A3 13 3A3 3Y3 1Aa 14 3A4 34 20E 40E oAi 2Yi 4Ai 4t 2A2 2Y2 4A2 42 2A3 2Y3 4A3 4Y3 2A4 ava 4A4 4Y4 The IDT logo is @ registered trademark of Integrated Davice Technology, Inc. 2544 drw 01 2544 drw 02 MILITARY AND COMMERCIAL TEMPERATURE RANGES JUNE 1996 1996 Integrated Device Technalagy, Inc. 5.2 2544/8IDTS4/74FCTIG244T/ATICTIET, 162244T/AT/CT/ET, 166244T/ATICT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES PIN CONFIGURATIONS 10E [_| 1 48 |_| 20E 10E 1 v1 [7] 2 47[ J 1A 2 12 [7] 3 46 [_] 1A2 3 GND C] 4 45 | GND GND 4 13 [| 5 44 |] 1A3 5 14 [7] 6 43 [] 1A4 6 vec [_| 7 42 [__] Vec Vec 7 2v1 (_ | 8 41] 2A1 2v1 8 ayvz[_| 9 40 [7] 2A2 2 9 GND [| 10 39 | | GND GND 10 23 [_ | 11 38 ["_] 2A3 2Y3 1 24 12 $048-1 37 2A4 ava 31 oy 13 S048-2 36 = 3A1 32 [| 14 35 [] 3A2 GND i 15 34 |_| GND GND 3a [__| 16 33 |] 3A3 3a [| 17 32 [7] 3A4 Vec [7] 18 31 [7] vec Voc 41 [| 19 30 |] 4A1 42 [ | 20 29 |] 4Az GND [_] 21 28 | | GND GND 43 [] 22 27 |] 4A3 44 [| 23 26 [7] 4A4 40E [| 24 25 [7] 208 AOE 2544 drw 03 ie SBA TOP VIEW PIN DESCRIPTION xOE 3-State Enable (Active LOW) xAX Data xYx 3-State Outputs NOTE: 2544 thi 01 1. On FCT16xH these pins have Bus Hold. Alf other pins are standard inputs, outputs or I/Os. 5.2 2IDT54/74FCTIG244T/ATI/CTIET, 162244T/AT/CTIET, 1GG244T/ATICT, 162H244T/ATICTIET FAST CMOS 16-81T BUFFER/LINE DRIVER ABSOLUTE MAXIMUM RATINGS" FUNCTION TABLE) MILITARY AND COMMERCIAL TEMPERATURE RANGES Symbol Rating Commercial Military | Unit Vrerm(2)! Terminal Voitage | -0.5 to +7.0 | -0.5to+7.0] V with Respect to GND VTERM@)| Terminal Voltage 0.5 to 0.5 to v with Respect to Vcc +0.5 Voc +0.5 GND 5 c NOTE: 2544 tl 02 TA Operating 40 to +85 | -55to+125 | C 1. H=HIGH Voltage Level Temperature X = Don't Care Taias | Temperature -55 to +125 | -65to +135 | C L = LOW Voltage Level Under Bias Z = High Impedance TsTG Storage -55 to +125 | -65to +150] C Temperature Pr Power Dissipation 1.0 1.0 W CAPACITANCE (TA = +25C, f= 1.0MHz) louT DC Output 60 to +120 | -60 to +120 | mA Symboi | Parameter(t) Conditions {| Typ. | Max. | Unit Current Cin Input VIN =0V 3.5 6.0 | pF NOTES: 2544 Ink 03 Capacitance 1. Stresses greaterthan thoselisted under ABSOLUTE MAXIMUMRATINGS Cout Output Vout = OV 35 8.0 pF may cause permanent damage to the device. This is a stress rating only Cc it and functional operation of the device at these or any other conditions apachance above those indicated in the operational sections of this specification is NOTE: 2544 Ink 04 not implied. Exposure to absolute maximum rating conditions for 1. This parameter is measured at characterization but not tasted. extended periods may affect reliability. 2. All device terminals except FCT162XXXT and FCT166XXXT output and VO terminais. 3. Output and I/O terminals for FCT162XXXT and FCT166XXXT. DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (STANDARD PARTS) Foliowing Conditions Apply Unless Otherwise Specified: Commercial: Ta = ~40C to +85C, Vcc = 5.0V + 10%; Military: Ta = -55C to +125C, Voc= 5.0V + 10% Symbol Parameter Test Conditions()) Min. | Typ.2)| Max. | Unit VIH Input HIGH Level Guaranteed Logic HIGH Level 2.0 _ Vv VIL Input LOW Level Guaranteed Logic LOW Level _ _ 0.8 Vv NH Input HIGH Current (Input pins)) | Vcc = Max. Vi = Voc ~~ - HH nA Input HIGH Current (I/O pins) _ +1 In Input LOW Current (Input pins){5) Vi= GND ~_ +1 Input LOW Current (I/O pins) ) _ +i lozH High Impedance Output Current Voc = Max. Vo=2.7V _ _ +1 pA loz (3-State Output pins) (5) Vo = 0.5V = +1 VIK Clamp Diode Voltage Vcc = Min., lin = -18mA _ -0.7 | -1.2 Vv los Short Circuit Current Vcc = Max., Vo = GND@) -80 | -140 | -225 | mA Vu Input Hysteresis _ _ 100 _ mV IoeL Quiescent Power Supply Current | Voc = Max., Vin = GND or Vcc 5 500 HA ICCH Iecez NOTES: 2844 Ink 05 Obons . For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. . Typical values are at Vcc = 5.0V, +25C ambient. . Not more than one output should be tested at one time. Duration of the test should not exceed one second. . Duration of the condition can not exceed one second. . The test limit for this parameter is + 5A at Ta = ~55C. .2IDTS4/74FCTIG244T/AT/CTIET, 162244T/AT/CT/ET, 166244T/ATICT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (BUS HOLD) Following Conditions Apply Unless Otherwise Specified: Commercial: Ta = 40C to +85C, Vcc = 5.0V + 10%; Military: Ta = -55C to +125C, Vec= 5.0V + 10% MILITARY AND COMMERCIAL TEMPERATURE RANGES Symbol Parameter Test Conditions Min. | Typ.@)| Max. | Unit VIH Input HIGH Level Guaranteed Logic HIGH Level 2.0 _ _ v VIL Input LOW Level Guaranteed Logic LOW Level _ - 0.8 v WH Input Standard Input) Vcc = Max. Vi = Voc _ +1 pA HIGH Standard I/0{5) _ _ +1 Current'4) | Bus Hold Input _ | +100 Bus Hold I/O _ _ 100 He Input Standard input'5) Vi = GND _ _ +1 LOW Standard 1/0!) _ _ +1 Current) | Bus Hold Input | +100 Bus Hold I/O _ _ +100 IBHH Bus Hold | Bus Hold Input Vcc = Min. Vi = 2.0V -50 _ _ pA {BHL Sustain Vi = 0.8V +50 _ _ Current(4) lozH High Impedance Output Current Vcc = Max. Vo=2.7V +1 pA Jozi (3-State Output pins) 5:6) Vo = 0.5V _ _ +1 Vik Clamp Diode Voltage Vcc = Min., lin =-18mA _ -0.7 | -1.2 Vv los Short Circuit Current Vcc = Max., Vo = GND) -80 -140 | -225 mA Vu Input Hysteresis ~ _ 100 _ mV lect Quiescent Power Supply Current | Vcc = Max., VIN= GND or Vcc _ 5 500 HA IccH lecz NOTES: 2544 ink 06 aOnhoan = . For conditions shown as Max. or Min.. use appropriate value specified under Electrical Characteristics for the applicable device type. . Typical values are at Vcc = 5.0V, +25C ambient. . Net more than one output should be tested at one time. Duration of the test should not exceed one second. . Pins with Bus Hold are identified in the pin description. . The test limit for this parameter is + 5uA at Ta = -55C. . Does not include Bus Hold 1/0 pins. 5.2IDTS4/74FCTIG244 T/AT/CTIET, 162244 T/ATI/CTIET, 166244T/AT/CT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER OUTPUT DRIVE CHARACTERISTICS FOR FCT16244T MILITARY AND COMMERCIAL TEMPERATURE RANGES Symbol Parameter Test Conditions(!) Min. | Typ.2)| Max. | Unit lo Output Drive Current Vcc = Max., Vo = 2.5V@) -50 | -180 | mA Vou Output HIGH Voltage Vec = Min. loH = -3mA 2.5 3.5 _ Vv VIN = VIH or VIL 10H = -12mA MIL. 2.4 3.5 = Vv loH = -15mA COM'L. IOH = 24mA MIL. 2.0 3.0 _ Vv oH = 32mA COM'L.4) VoL Output LOW Voltage Vec = Min. loL = 48mA MIL. 0.2 0.55 v VIN = Vin or Vit loL=64mA COM'L. loFF Input/Output Power Off Leakage} Vcc = OV, Vin or Vo <4.5V _ +1 pA 2544 Ink 07 OUTPUT DRIVE CHARACTERISTICS FOR FCT162244T Symbol Parameter Test Conditions ) Min. | Typ.2)] Max. | Unit lope Output LOW Current Vcc = 5V, VIN = ViH or Vit, VouT= 1.5V@) 60 115 | 200 | mA lO0H Output HIGH Current Vec = 5V, VIN = ViH or ViL, Vour= 1.5V'3) -60 | -115] -200] mA Vou Output HIGH Voltage Vcc = Min. 1OH = -16MA MIL. 2.4 3.3 _ Vv Vin = Viktor Vit lOH = 24mA COM'L. VoL Output LOW Voltage Vcc = Min. loL = 16mA MIL. _ 0.3 0.55 v VIN = VIH or Vit fol = 24mA COM'L. 2544 Ink OB OUPUT DRIVE CHARACTERISTICS FOR FCT166244T Symbol Parameter Test Conditions Min. Typ.2} Max.| Unit loo Output LOW Current Vcc = 5V, VIN = Vinor VIL, VouT= 1.5V@) 16 48 96 mA JODH Output HIGH Current Vec = 5V, VIN = Vin or ViL, Vout = 1.5V@) -i6} -48] -96] mA VOH Output HIGH Voltage Vcc = Min. lon = 6mA MIL. 2.4 3.3 _- Vv Vin = Vid or Vit (0H = -8mA COM'L. VoL Output LOW Voitage Vcc = Min. lo. = 6MA MIL. _ 0.3 0.55 Vv VIN = VIH or VIL lot = 8mMA COM'L, NOTES: 2544 tnk 09 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. . Typical values are at Vcc = 5.0V, +25C ambient. . Not more than one output should be tested at one time. . Duration of the condition can not exceed one second. . The test limit for this parameter is + 5A at Ta = 55C. ms & Duration of the test should not exceed one second. 5.2IDTS4/74FCTIG244T/AT/CT/ET, 162244T/ATICT/ET, 166244T/AT/CT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES POWER SUPPLY CHARACTERISTICS Symbol Parameter Test Conditions() Min. |Typ.@)| Max. | Unit Alcc Quiescent Power Supply Current | Vcc = Max. _ 0.5 1.5 mA TTL Inputs HIGH Vin = 3.4V1) Iccb Dynamic Power Supply Vcc = Max. VIN = Voc _- 60 100 pA/ Current() Outputs Open Vin = GND MHz xOE = GND One Input Toggling 50% Duty Cycle Ic Total Power Supply Current(6) Vcc = Max. VIN = Voc 0.6 1.5 mA Outputs Open Vin = GND fi = 10MHz 50% Duty Cycle VIN =3.4V | o9 | 23 xOE = GND Vin = GND One Bit Toggling Vcc = Max. VIN = Voc _ 2.4 | 456) Outputs Open Vin = GND fi = 2.5MHz 50% Duty Cycle VIN = 3.4V _ 6.4 | 16.56) xOE = GND Vin = GND Sixteen Bits Toggling NOTES: 2544 tbl 10 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. . Typical values are at Vcc = 5.0V, +25C ambient. Per TTL driven input (Vin = 3.4V). All other inputs at Vcc or GND. . This parameter is not directly testable, but is derived for use in Tatal Power Supply Calculations. . Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. ic = JquiescenT + linpuTs + IDYNAMIC Ic = Iec + Alcc DHNT + Iccp (fcPNcp/2 + fiNi) lec = Quiescent Current (IccL, IccH and Iccz) Alcc = Power Supply Current for a TTL High Input (Vin = 3.4V) DH = Duty Cycle for TTL Inputs High Nt = Number of TTL Inputs at DH tIccp = Dynamic Current Caused by an input Transition Pair (HLH or LHL) fcp = Clock Frequency for Register Devices (Zero for Non-Register Devices) Ncp = Number of Clock Inputs at for fi = Input Frequency N: = Number of Inputs at fi AaPop .2 6IDTS4/74FCTIG244T/AT/CT/ET, 162244 T/ATICT/ET, 166244T/AT/CT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES SWITCHING CHARACTERISTICS OVER OPERATING RANGE FOR FCT16244T/FCT162244T FCT162441/162244T/166244T FCT16244AT/162244AT/166244AT Com'l. Mil. Com't. Mil. Symbol Parameter Condition Min.) | Max. | Min.@) | Max. | Min.@) | Max. | Min.) | Max. | Unit Pn Propagation Delay Cu = 50pF 15 6.5 1.5 7.0 1.5 48 z= 51 ns tPHL xAx to xYx Ri = 5009 tPZH Output Enable Time 1.5 8.0 1.5 8.5 1.5 6.2 1.5 6.5 ns tPZL tPHZ Output Disable Time 1.5 7.0 1.5 7.5 15 5.6 1.5 5.9 ns tPLZ tsk(o) Output Skew(9) _ 0.5 _ 0.5 0.5 0.5 ns 2544 tbl 11 FCT16244CT/162244CT/166244CT FCT16244ET/162244ET Com'l. Mil. Com'l. Mil. | Symbol Parameter Condition Min.@) | Max. { Min.@) | Max. | Min? | Max. | Min.@) | Max. | Unit {PLH Propagation Delay CL = SOpF 1.5 4.1 1.5 46 1.5 3.2 _ _ ns {PHL xAx to xx Rt = 5002 tPZH Output Enable Time 1.5 5.8 1.5 6.5 1.5 4.4 _ _- ns tPZL. tPHZ Output Disable Time 1.5 5.2 1.5 5.7 15 3.6 _ ns {PLZ tsk(o) Output Skew!) _ 0.5 ~ 0.5 _ 0.5 _ _ ns NOTES: 2544 tht 12 1. See test circuit and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed by design. 5.2 7IDTS4/74FCT16244T/AT/CT/ET, 162244T/AT/CTIET, 166244T/AT/CT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER TEST CIRCUITS AND WAVEFORMS TEST CIRCUITS FOR ALL OUTPUTS Vcc o-* 7.0 I 5000 VIN Pulse Generator D.U.T. 5002 2544 dw 05 SET-UP, HOLD AND RELEASE TIMES DATA av 1.5V INPUT is TIMING 3V INPUT 1.5V ASYNCHRONOUS CONTROL ov PRESET 3V CLEAR 1.5V ETC. ov SYNCHRONOUS CONTROL PRESET Ny CLEAR Fy CLOCK ENABLE ETC. 2544 drw 06 PROPAGATION DELAY SAME PHASE INPUT TRANSITION OUTPUT OPPOSITE PHASE INPUT TRANSITION 2544 drw 08 MILITARY AND COMMERCIAL TEMPERATURE RANGES SWITCH POSITION Test Switch Open Drain Disable Low Closed Enable Low All Other Tests Open DEFINITIONS: 2544 Ink 13 Ci= Load capacitance: includes jig and probe capacitance. Rt = Termination resistance: should be equal to Zour of the Pulse Generator. PULSE WIDTH LOW-HIGH-LOW PULSE 1.5V tw HIGH-LOW-HIGH 1.5V PULSE 2544 drw 07 ENABLE AND DISABLE TIMES ENABLE DISABLE _ 3 CONTROL - 15v INPUT / 7 ov wm] {PLZ ka OUTPUT 3.5V NORMALLY VK Y LOW 0.3 VoL => -|ohav VoH OUTPUT NORMALLY SWiGH Na HIGH EC w ov NOTES: 2544 drw 09 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH 2. Pulse Generator for All Pulses: Rate < 1.0MHz; tr < 2.5ns; ta < 2.5nsIDT54/74FCTIG244T/AT/CT/ET, 162244 T/AT/CT/ET, 166244T/ATICT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES ORDERING INFORMATION IOT XX FCT x x XXXX x x Temp. Range Drive BusHold Device Type Package Process Blank B Po PV PA E 244T 244AT 244CT 244ET { Blank }H 162 | 166 1 74 Commercial MIL-STD-883, Class B Shrink Small Outline Package (SO48-1) Thin Shrink Small Outline Package (SO48-2) CERPACK (E48-1)} Non-Inverting 16-Bit Buffer/Line Driver Standard Bus Hold 16-Bit High Drive 16-Bit Balanced Drive 16-Bit Light Drive -55C to +125C 40C to +85C 2544 drw 10 5.2